cruise control INFINITI QX60 2016 Owner's Guide

To cancel the preset speed,use any of the
following three methods:
1. Press the CANCEL button. The SET indica-
tor will go out.
2. Tap the brake pedal. The SET indicator will
go out.
3. Turn the CRUISE ON/OFF switch off. Both
the CRUISE indicator and SET indicator will
go out.
To reset at a faster cruising speed,use one of
the following three methods:
1. Depress the accelerator pedal. When the
vehicle attains the desired speed, push and
release the COAST/SET switch.
2. Push and hold the ACCEL/RES set switch.
When the vehicle attains the speed you de-
sire, release the switch.
3. Push, then quickly release the ACCEL/ RES
switch. Each time you do this, the set speed
will increase by about 1 mph (1.6 km/h).
To reset at a slower cruising speed,use one
of the following three methods:
1. Lightly tap the brake pedal. When the ve-
hicle attains the desired speed, push the
COAST/SET switch and release it.2. Push and hold the COAST/SET switch. Re-
lease the switch when the vehicle slows
down to the desired speed.
3. Push, then quickly release the COAST/SET
switch. Each time you do this, the set speed
will decrease by about 1 mph (1.6 km/h).
To resume the preset speed,push and re-
lease the ACCEL/RES switch. The vehicle will
resume the last set cruising speed when the
vehicle speed is over 25 mph (40 km/h).
Automatic cancellation
Under the following condition, a chime will sound
and the system control is automatically canceled.
●When the vehicle speed falls below approxi-
mately 20 mph (32 km/h)
●When the shift lever is not in the D (Drive) or
Manual mode
●When the parking brake is applied
●When the VDC (including the TCS) oper-
ates
●When a wheel slips
Warning light
When the system is not operating properly, the
chime sounds and the system warning light (or-
ange) will come on.
Action to take:
If the warning light comes on, park the vehicle in a
safe place. Turn the engine off, restart the engine,
resume driving and then perform the setting again.
If it is not possible to set or the indicator
stays on, it may indicate that the system is
malfunctioning. Although the vehicle is still
driveable under normal conditions, have the
vehicle checked. It is recommended that you
visit an INFINITI retailer for this service.
LSD2067
5-92Starting and driving

●When the VDC system is off (To use the
DCA system, turn on the VDC, then push the
dynamic driver assistance switch.)
For additional information about the VDC
system, refer to “Vehicle Dynamic Control
(VDC) system” in this section.
●When ABS or VDC (including the TCS) is
operating
When the Conventional (fixed speed) cruise con-
trol mode is operating, the DCA system will not
operate. (To use the DCA system, turn the Con-
ventional (fixed speed) cruise control mode off,
then push the dynamic driver assistance switch.)
For additional information about the Conventional
(fixed speed) cruise control mode, refer to “Intel-
ligent Cruise Control (ICC)” in this section.
When the engine is turned off, the system is
automatically turned off.
1System set display with vehicle ahead
2System set display without vehicle ahead
Automatic cancellation
Condition A:
Under the following conditions, the DCA system
is automatically canceled. The chime will sound
and the DCA cancellation message will display.●When the VDC system is turned off
●When the VDC or ABS operates
●When SNOW mode is selected by using the
INFINITI drive mode selector
Action to take:
When the conditions listed above are no longer
present, turn the system off with the dynamic
driver assistance switch. Turn the DCA system
back on to use the system.
LSD2126LSD2080
5-104Starting and driving

Condition B:
When the sensor area of the front bumper is dirty,
making it impossible to detect a vehicle ahead,
the DCA system is automatically canceled.
The chime sounds and the system warning light
(orange) will come on and the “Sensor Blocked”
indicator will appear.
Action to take:
If the warning light comes on, park the vehicle in a
safe place, turn the engine off. Clean the sensor
area of the bumper and then perform the settings
again.
Condition C:
When the DCA system is not operating properly,
the chime sounds and the system warning light
(“DCA” orange) will come on.
Action to take:
If the warning light comes on, park the vehicle in a
safe place. Turn the engine off, restart the engine,
and turn on the DCA system again.If it is not possible to set the system or the
indicator stays on, it may indicate that the
system is malfunctioning. Although the ve-
hicle is still driveable under normal condi-
tions, have the vehicle checked. It is recom-
mended that you visit an INFINITI retailer
for this service.
SYSTEM MAINTENANCE
The sensor for the DCA system is common with
ICC and is located behind the front bumper.
For additional information, refer to “Intelligent
Cruise Control (ICC)” in this section.
DCA warning light (orange)
LSD2081
Starting and driving5-105

●Above 40 mph (64 km/h), it is more effi-
cient to use A/C to cool the vehicle due to
increased aerodynamic drag.
●Recirculating the cool air in the cabin
when the A/C is on reduces cooling load.
4.Drive at Economical Speeds and Dis-
tances
●Observing the speed limit and not ex-
ceeding 60 mph (97 km/h) (where legally
allowed) can improve fuel efficiency due
to reduced aerodynamic drag.
●Maintaining a safe following distance be-
hind other vehicles reduces unnecessary
braking.
●Safely monitoring traffic to anticipate
changes in speed permits reduced brak-
ing and smooth acceleration changes.
●Select a gear range suitable to road con-
ditions.
5.Use Cruise Control
●Using cruise control during highway driv-
ing helps maintain a steady speed.
●Cruise control is particularly effective in
providing fuel savings when driving on flat
terrains.
6.Plan for the Shortest Route●Utilize a map or navigation system to de-
termine the best route to save time.
7.Avoid Idling
●Shutting off your engine when safe for
stops exceeding 30–60 seconds saves
fuel and reduces emissions.
8.Buy an Automated Pass for Toll Roads
●Automated passes permit drivers to use
special lanes to maintain cruising speed
through the toll and avoid stopping and
starting.
9.Winter Warm Up
●Limit idling time to minimize impact to fuel
economy.
●Vehicles typically need no more than
30 seconds of idling at start-up to effec-
tively circulate the engine oil before driv-
ing.
●Your vehicle will reach its ideal operating
temperature more quickly while driving
versus idling.10.Keeping your Vehicle Cool
●Park your vehicle in a covered parking
area or in the shade whenever possible.
●When entering a hot vehicle, opening the
windows will help to reduce the inside
temperature faster, resulting in reduced
demand on your A/C system.
Starting and driving5-129

SPECIAL WINTER EQUIPMENT
It is recommended that the following items be
carried in the vehicle during winter:
●A scraper and stiff-bristled brush to remove
ice and snow from the windows and wiper
blades.
●A sturdy, flat board to be placed under the
jack to give it firm support.
●A shovel to dig the vehicle out of snowdrifts.
●Extra washer fluid to refill the windshield-
washer fluid reservoir.
DRIVING ON SNOW OR ICE
WARNING
●Wet ice (32°F, 0°C and freezing rain) ,
very cold snow or ice can be slick and
very hard to drive on. The vehicle will
have much less traction or “grip” under
these conditions. Try to avoid driving on
wet ice until the road is salted or
sanded.
●Whatever the condition, drive with cau-
tion. Accelerate and slow down with
care. If accelerating or downshifting too
fast, the drive wheels will lose even
more traction.●Allow more stopping distance under
these conditions. Braking should be
started sooner than on dry pavement.
●Allow greater following distances on
slippery roads.
●Watch for slippery spots (glare ice) .
These may appear on an otherwise
clear road in shaded areas. If a patch of
ice is seen ahead, brake before reach-
ing it. Try not to brake while on the ice,
and avoid any sudden steering
maneuvers.
●Do not use the cruise control on slip-
pery roads.
●Snow can trap dangerous exhaust
gases under your vehicle. Keep snow
clear of the exhaust pipe and from
around your vehicle.
ENGINE BLOCK HEATER (if so
equipped)
Engine block heaters are used to assist with cold
temperature starting.
The engine block heater should be used when
the outside temperature is 20°F (-7°C) or lower.
WARNING
●Do not use your engine block heater
with an ungrounded electrical system or
a 2-pronged adapter. You can be seri-
ously injured by an electrical shock if
you use an ungrounded connection.
●Disconnect and properly store the en-
gine block heater cord before starting
the engine. Damage to the cord could
result in an electrical shock and can
cause serious injury.
●Use a heavy-duty 3-wire, 3-pronged ex-
tension cord rated for at least 10 A. Plug
the extension cord into a Ground Fault
Interrupt (GFI) protected, grounded
110-VAC outlet. Failure to use the
proper extension cord or a grounded
outlet can result in a fire or electrical
shock and cause serious personal
injury.
To use the engine block heater:
1. Turn the engine off.
2. Open the hood and unwrap the engine block
heater cord.
3. Plug the engine block heater cord into a
grounded 3-wire, 3-pronged extension
cord.
Starting and driving5-145

Use the following steps to mount the front license
plate:
Before mounting the license plate, confirm that the
following parts are enclosed in the plastic bag:
Only use the recommended mounting position,
otherwise the Intelligent Cruise Control (ICC) (if
so equipped) sensor obstruction may result.
●License plate bracket
●License plate bracket (J-nut) screws x 2
●License plate screws x 2
●Screw grommets x 2
1. Park the vehicle on flat, level ground.
2. Locate the center position
Aas illustrated.
Line up the license plate bracket under the
top of the front bumper
Bwith the tabsC.
Hold the license plate bracket in place.
3. Mark the center of the hole
Dwith a felt-tip
pen.
4. Carefully drill two pilot holes using a 0.39 in
(10 mm) drill bit at the marked locations.(Be
sure that the drill only goes through the
bumper fascia.)
5. Insert the grommets into the holes in the
bumper fascia.
6. Insert a small flat-bladed screwdriver into
the grommet hole to turn the threaded part of
the grommet 90°
E.LTI2035
INSTALLING FRONT LICENSE PLATE
Technical and consumer information9-13

●While going downhill, the weight of the
trailer pushing on the tow vehicle may de-
crease overall stability. Therefore, to main-
tain adequate control, reduce your speed
and shift to a lower gear. Avoid long or
repeated use of the brakes when descend-
ing a hill, as this reduces their effectiveness
and could cause overheating. Shifting to a
lower gear instead provides “engine brak-
ing” and reduces the need to brake as fre-
quently.
●If the engine coolant temperature rises to a
high temperature, refer to “If your vehicle
overheats” in the “In case of emergency”
section of this owner’s manual.
●Trailer towing requires more fuel than normal
circumstances.
●Avoid towing a trailer for your vehicle’s first
500 miles (805 km) .
●For the first 500 miles (805 km) that you do
tow, do not drive over 50 mph (80 km/h).
●Have your vehicle serviced more often than
at intervals specified in the recommended
Maintenance Schedule in the “INFINITI Ser-
vice and Maintenance Guide”.●When making a turn, your trailer wheels will
be closer to the inside of the turn than your
vehicle wheels. To compensate for this,
make a larger than normal turning radius
during the turn.
●Crosswinds and rough roads will adversely
affect vehicle/trailer handling, possibly caus-
ing vehicle sway. When being passed by
larger vehicles, be prepared for possible
changes in crosswinds that could affect ve-
hicle handling.
Do the following if the trailer begins to sway:
1. Take your foot off the accelerator pedal to
allow the vehicle to coast and steer as
straight ahead as the road conditions allow.
This combination will help stabilize the ve-
hicle
– Do not correct trailer sway by steering or
applying the brakes.
2. When the trailer sway stops, gently apply the
brakes and pull to the side of the road in a
safe area.
3. Try to rearrange the trailer load so it is bal-
anced as described in this section.●Be careful when passing other vehicles.
Passing while towing a trailer requires con-
siderably more distance than normal pass-
ing. Remember, the length of the trailer must
also pass the other vehicle before you can
safely change lanes.
●Downshift the transmission to a lower gear
for engine braking when driving down steep
or long hills. This will help slow the vehicle
without applying the brakes.
●Avoid holding the brake pedal down too long
or too frequently. This could cause the
brakes to overheat, resulting in reduced
braking efficiency.
●Increase your following distance to allow for
greater stopping distances while towing a
trailer. Anticipate stops and brake gradually.
●INFINITI recommends that the cruise control
not be used while towing a trailer.
●Some states or provinces have specific
regulations and speed limits for vehicles that
are towing trailers. Obey the local speed
limits.
●Check your hitch, trailer wiring harness con-
nections, and trailer wheel lug nuts after
50 miles (80 km) of travel and at every break.
9-28Technical and consumer information

C
Capacities and recommended fuel/lubricants . .9-2
Cargoareastoragebin.............2-57
Cargo(Seevehicleloadinginformation)....9-14
Car phone or CB radio.............4-113
CD care and cleaning..............4-98
CD player (See audio system).........4-76
Check tire pressure...............2-28
Child restraints.......1-25,1-25,1-27,1-29
LATCH (Lower Anchors and Tethers for
CHildren) System..............1-29
Precautions on child
restraints.........1-27,1-34,1-40,1-46
Top tether strap anchor point locations . .1-32
Child restraint with top tether strap.......1-31
Child safety rear door lock............3-6
Chimes, audible reminders...........2-15
Cleaningexteriorandinterior........7-2,7-4
Climatecontrolseatswitch...........2-44
Clock setting
(models with Navigation System)........4-18
Clock setting
(models without Navigation System).......4-9
C.M.V.S.S. certification label..........9-11
Cold weather driving..............5-144
Compact disc (CD) player...........4-76
Consolebox...................2-52
Consolelight...................2-65
Continuously Variable Transmission (CVT) . . .5-18
Continuously Variable Transmission (CVT)
fluid......................8-13
Driving with Continuously Variable
Transmission (CVT).............5-18
Control panel buttons..............4-11Brightness/contrast button......4-10,4-20
Enterbutton...............4-4,4-11
Without navigation system..........4-4
Controls
Audio controls (steering wheel).......4-99
Heater and air conditioner controls.....4-49
Coolant
Capacities and recommended
fuel/lubricants.................9-2
Changingenginecoolant...........8-9
Checking engine coolant level........8-9
Engine coolant temperature gauge.....2-6
Corrosion protection...............7-6
Cruisecontrol...............5-74,5-75
Cupholders...................2-54
D
Daytime running light system (Canada only) . .2-39
Defroster switch
Rear window and outside mirror defroster
switch.....................2-36
Digital Versatile Disc (DVD) player.......4-80
Dimensionsandweights.............9-9
Dimmer switch for instrument panel......2-40
Display......................2-16
Display controls
(seecontrolpanelbuttons) ........4-4,4-11
Distance Control Assist (DCA) system.....5-95
Doors........................3-4
Drive belt.....................8-17
Drive positioner, Automatic...........3-34
Driving
Cold weather driving............5-144Driving with Continuously Variable
Transmission (CVT).............5-18
Precautions when starting and driving....5-4
Driving the vehicle................5-18
Dual head restraint DVD system.......4-101
Dual power moonroof...........2-62,2-62
E
Economy-fuel.................5-130
Emergency engine shutoff.........5-15,6-3
Emission control information label.......9-11
Emission control system warranty.......9-31
Engine
Before starting the engine..........5-16
Blockheater ................5-145
Capacities and recommended
fuel/lubricants.................9-2
Changing engine coolant...........8-9
Changingengineoil.............8-11
Changing engine oil filter..........8-12
Checking engine coolant level........8-9
Checking engine oil level..........8-10
Engine compartment check locations....8-7
Engine coolant temperature gauge.....2-6
Engine cooling system............8-8
Engineoil...................8-10
Engine oil and oil filter recommendation . . .9-6
Engine oil viscosity..............9-7
Engine serial number............9-11
Engine specifications.............9-8
Starting the engine.............5-17
Engine coolant temperature gauge.......2-6
Enter button.................4-4,4-11
Event Data recorders..............9-33
10-2

Inside automatic anti-glare mirror........3-32
Instrument brightness control..........2-40
Instrument panel...............0-6,2-2
Instrument panel dimmer switch........2-40
Intelligent cruise control (ICC) system
Brake assist.................5-76
Intelligent Key system
Key operating range..............3-8
Key operation................3-10
Mechanicalkey ................3-3
Remote keyless entry operation.......3-13
Troubleshooting guide............3-17
Warning signals...............3-17
Interiorlight....................2-65
iPod®Player ...............4-88,4-90
ISOFIX child restraints.............1-29
J
Jump starting...............6-10,8-17
K
Key.........................3-2
Key fob battery replacement..........8-24
Keyless entry
With Intelligent Key system
(See Intelligent Key system).........3-13
L
Labels
Air conditioner specification label.....9-12C.M.V.S.S. certification label........9-11
Emission control information label.....9-11
Engine serial number............9-11
F.M.V.S.S. certification label.........9-11
Tire and Loading Information label.....9-12
Vehicle identification number (VIN).....9-10
Vehicle identification number (VIN) plate . .9-10
Warning labels (for SRS)..........1-67
Lane Departure Prevention (LDP)
system...............5-26,5-31,5-34
Lane Departure Warning (LDW)
system...............5-26,5-31,5-34
LATCH (Lower Anchors and Tethers for CHildren)
System......................1-29
License plate
Installing the license plate..........9-13
Liftgate......................3-22
Liftgate release..................3-26
Light
Air bag warning light.........1-67,2-12
Brake light (See stop light).........8-26
Bulb check/instrument panel.........2-8
Bulbreplacement..............8-26
Charge warning light.............2-9
Consolelight.................2-65
Exterior and Interior lights..........8-26
Foglights...................8-26
Foglightswitch ...............2-41
Headlight and turn signal switch......2-36
Headlight control switch..........2-37
Headlights..................8-26
Interiorlight..................2-65
Lightbulbs..................8-26
Low tire pressure warning light.......2-10
Low windshield-washer fluid warning
light......................2-27Passenger air bag and status light.....1-58
Personal lights................2-66
Security indicator light............2-14
Warning/indicator lights and audible
reminders.............2-8,2-9,2-13
Lights.......................8-26
Maplights ..................2-66
Lock
Child safety rear door lock..........3-6
Gloveboxlock................2-52
Liftgate release................3-26
Power door locks............3-5,3-6
Loose fuel cap warning.............2-30
Low fuel warning light..........2-11,2-27
Low tire pressure warning light.........2-10
Low windshield-washer fluid warning light . . .2-27
Luggage hook..................2-56
Luggage rack (see roof rack)..........2-57
Luggage (See vehicle loading information) . .9-14
M
Maintenance
General maintenance.............8-2
Insidethevehicle...............8-3
Maintenance precautions...........8-5
Outside the vehicle..............8-2
Seat belt maintenance............1-24
Under the hood and vehicle.........8-4
Maintenance requirements............8-2
Malfunction indicator light............2-13
Maplights ....................2-66
Mappocket....................2-51
Memory Seat...................3-34
Meters and gauges................2-4
10-4