INFINITI QX60 HYBRID 2014 Quick Reference Guide

Clock Set/Adjustment
DIGITAL CLOCK ADJUSTMENT
To adjust the time and the appearance
of the clock on the display:
1. Press the SETTING button on the control panel.
2.
Touch the Others key.
3.
Touch the Clock key.

The following settings can be adjusted:
•
On-screen Clock: The clock in the upper right corner
of the display can be turned ON or OFF.
• Clock Format (24h): The clock can be set to 12 hours or 24 hours.
• Offset (hour): The time can be adjusted by increasing or decreasing per hour.
•
Offset (min): The time can be adjusted by increasing or decreasing per minute.
• Daylight Savings Time: The application of daylight savings time can be turned ON or OFF.
• Time Zone: Adjust the time zone. Choose a time zone from the available list.
Press the BACK button to return to the previous screen.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (secti\
on 4)” of your
Owner’s Manual.
9
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 99/24/13 11:43 AM

10
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or unlock your
vehicle, open your liftgate and remotely start the engine. It is importa\
nt to
make sure the Intelligent Key is with you (that is, in your pocket or p\
urse).
REMOTE ENGINE START* (if so equipped)

The remote engine start system must be enabled in the vehicle
settings within the vehicle information display.

The remote engine start operating range is approximately 200 ft
(60 m) from the vehicle. The effective operating range may be
shorter due to environmental conditions or obstacles between you
and the vehicle.

For the remote engine start to function, the vehicle must be in the
P (PARK) position with the ignition off, and all the doors closed
and locked.

To start your vehicle remotely:
1. Press the

button
01.
2. Within 5 seconds press and hold the remote
engine start

button
02 for at least 2 seconds.

The engine will start and the parking lights will turn on.

Automatic climate control will begin heating or
cooling the vehicle depending on the last used mode.

The engine will run for 10 minutes and then turn off.

Repeat steps 1 and 2 to extend the time for an additional 10 minute peri\
od.
• After two remote starts the ignition switch must be cycled before the re\
mote
start can be
used again.

To start driving depress the brake pedal and push the ignition switch
START/STOP button.
LOCKING AND UNLOCKING THE VEHICLE

The lock and unlock operating range of the Intelligent Key is within 31.\
5 in (80 cm) from
each request switch.

To lock the vehicle, push either door handle request switch
03 once or press the
button
01 on the key fob.
To unlock the vehicle, perform one of the following procedures:
• Push either door handle request switch

03 once; the corresponding door will unlock. Push
the door handle request switch again within 30 seconds; all other doors will unlock, or
• Press the

button
04 on the key fob to unlock the driver’s side door. Press the

button again; all other doors will unlock.
LIFTGATE RELEASE

To open the rear liftgate, press the
button
05 for longer than 1 second.
To close the rear liftgate, press the
button
05 again for longer than 1 second.
PANIC ALARM

The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the
button
06 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
first drive features
02
01
04
05
06
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 109/24/13 11:43 AM

INTELLIGENT KEy BATTERy DISCHARGE

If the battery of the Intelligent Key is discharged,
or environmental conditions interfere with the
Intelligent Key operation, start the engine according
to the following procedure:
1. Move the shift lever to the P (PARK) position.
2. Firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key
and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch while depressing
the brake pedal and the engine will start.
*Laws in some communities may restrict the use of remote starters. Check\
local regulations before using this feature.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and
the “Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
11
Power Liftgate

When the liftgate is closed and locked, the liftgate
will open automatically by:
• Pushing the power liftgate switch

01 on the
instrument panel.
• Pushing the liftgate opener switch

02, the
liftgate must be unlocked, or you must have the
Intelligent Key with you (in your pocket or purse).
• Pressing the

button
03 on the INFINITI
Intelligent Key for more than 1 second.

The power liftgate operation can be turned on or
off by the power liftgate main switch

04 on the
instrument panel.

•
When the power liftgate main
switch is pushed to the OFF
position, power operation is not
available using the power liftgate
switch on the liftgate

05 or the
liftgate opener switch 02.
For more information, refer to the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
0401
02
0503
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 119/24/13 11:43 AM

first drive features
12
Power Seat Adjustments
To slide the seat forward or backward, push the
control switch

01 forward or backward.

To recline the seatback, push the switch
02
forward or backward.
SEAT LIFTER

To raise or lower the front portion or height of the
seat, push the front or back end of the switch

01 up or down.
POWER LUMBAR SUPPORT (if so equipped for driver’s seat)

To adjust the seat lumbar support, push the front or back end of the swi\
tch
03.
For more information, refer to the “Safety —— seats, seat belts and supplemental restraint system (section 1)”\
of your
Owner’s Manual.
2ND Row Seats
To slide the seat forward or backward, pull the
center of the bar

01 up and hold it while you slide
the seat forward or backward to the desired
position. Release the bar to lock the seat
in position.

To recline the seatback, pull up on the recline handle

02 and lean back. To bring the seatback forward, pull

the lever up and lean your body forward. Release the
lever to lock the seatback in position.
MULTI-MODE/CHILD SEAT ACCESS FUNCTION

This feature is not available on driver’s side of 2nd row seat.

If a child safety seat is installed on the passenger’s side of the 2nd row seat, the 3rd row
can be accessed without removing the child safety seat.

To access the 3rd row from outside the vehicle, lift up on the seatback release lever
03.
EZ ENTRy MODE

To enter the 3rd row from outside the vehicle, lift up on fully the seatback lever
03.
This will release the back of the seat and fold up the seat cushion.

For access to the rear seat slide the entire seat forward by pushing on \
the upper
seatback area.

To return the seat to a locked position, push the upper seatback rearwar\
d until the
seatback and track are locked. Push the seat cushion down. Locking the s\
eatback will
also lock the track.
For more information, refer to the “Safety —— seats, seat belts and supplemental restraint system (section 1)”\

of your Owner’s Manual.
010203
0102
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 129/24/13 11:43 AM

13
3RD Row Manual Reclining Seatback
To recline the seatback, pull up on the latch
01
located on the outside corner of each seatback.
Lean back until the desired angle is obtained.

To bring the seatback forward again, pull up on the
latch

01 and move your body forward. The
seatback will move forward.
For more information, refer to the “Safety —— seats, seat belts and
supplemental restraint system (section 1)” of your Owner’s Manual.
Automatic Drive Positioner (if so equipped)
Two positions for the driver’s seat, steering column
and outside mirrors can be stored in the automatic
drive positioner
01 memory.

Follow these procedures to set the memory positions:
• Confirm the shift lever is in the P (PARK) position.
• Push the ignition switch to the ON position.
•
Adjust the driver’s seat, steering column and
outside mirrors to the desired positions using the
adjusting switches for each feature.
• Push the SET switch and within 5 seconds, push the memory switch (1 or 2) for at least 1 second.
• The indicator light on the memory switch you select will illuminate for \
approximately
5 seconds, and a chime will sound (if so equipped) when memory is stor\
ed correctly.
• The driver’s seat, steering column and outside mirror positions are n\
ow set to your preference.

These memorized positions can also be linked to your INFINITI Intelligen\
t Key.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Outside Mirror Control Switch
To select the right or left side mirror, move the
control switch

01 right or left.

Adjust each mirror to the desired position using the
switch

02.

To fold the outside rearview mirrors, push the
switch
03 to the
position. To unfold the
outside rearview mirrors, push the switch

03 to
the

position.
02
01
03
01
01
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 139/24/13 11:43 AM

first drive features
14REVERSE TILT-DOWN FEATURE (if so equipped)


The reverse tilt-down feature will turn the selected outside mirror surf\
ace downward to
provide better rear visibility close to the vehicle.
1. Push the ignition switch to the ON position.
2. Choose the right or left outside mirror by operating the outside mirror \
control switch
01.
3. Move the shift lever to the R (REVERSE) position.
4. The outside mirror surfaces move downward.

The outside mirror surfaces will return to their original positions when\
one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center (neutral) posit\
ion.
• The ignition switch is pushed to the OFF position.
For more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Hybrid System
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).

Depress the brake pedal.

Press the ignition switch START/STOP button to
start the hybrid system.
TURNING THE HYBRID SYSTEM OFF

Move the shift lever to the P (PARK) position and
apply the parking brake.

Press the ignition switch START/STOP button to turn the hybrid system off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Assist Charge Gauge

This shows the power consumed 02, or generated
01 by the electric motor.
For more information, refer to the “Hybrid System Overview” section and the
“Instruments and controls (section 2)” of your Owner’s Manual.0102
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 149/24/13 11:43 AM

15
Headlight Control Switch
HEADLIGHT CONTROL


Turn the headlight control switch to the
position
01 to turn on the front parking, tail, license plate and

instrument panel lights. Turn the switch to the
position 02 to turn on the headlights.
AUTOLIGHT SySTEM


The autolight system will automatically turn the headlights on when it i\
s dark and off when
it is light. The system will keep the headlights on for a period of time\
after you turn the
ignition off and all doors are closed.


To activate the autolight system, turn the headlight control switch to t\
he AUTO position
03
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
position
01 or
position
02.
HIGH BEAM SELECT


Push the headlight control switch forward
04 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel.
Pull the headlight switch back to the original
position to select the low beam. The blue
indicator light goes off.


Pull and release the headlight control switch
05 to
flash the headlight high beams on and off.
FOG LIGHT SWITCH


The headlights must be in auto, or the low
beams

selected for the fog lights to operate.


Turn the switch (inside collar) to the
position
06
to turn the fog lights on.


Turn the switch (inside collar)
to the OFF position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
03
04
06
01
05
02
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 159/24/13 11:43 AM

first drive features
Windshield Wiper and Washer Switch

Move the lever to the following positions to operate
the windshield wipers:

01
Mist (MIST) – One sweep operation of the
front wipers.

02
Auto (AUTO) – Operates the speed-sensing
and rain-sensing (if so equipped) front wipers
intermittently. The intermittent speed can be
adjusted by twisting the time control ring

03
to increase or decrease wiper speed
or sensitivity.

04
Low (LO) – Front wipers operate at a
continuous low-speed.

05
High (HI) – Front wipers operate at a
continuous high-speed.

06
Pull the lever toward you to activate the
front washer. The front wipers will operate
several times.
RAIN-SENSING AUTO WIPER SySTEM (if so equipped)


The rain-sensing auto wiper system can automatically turn on the wipers \
and adjust the
wiper speed depending on the rainfall and the vehicle speed.


To set the rain-sensing auto wiper system, push the lever down to the AUTO position
02.
The wiper will sweep once while the ignition switch is in the ON position.


The rain sensor sensitivity level can be adjusted by turning the time co\
ntrol ring
03 toward
the front or toward the rear.
REAR WINDSHIELD WIPER AND WASHER

07
Intermittent (INT) – Rear wiper
operates intermittently.

08
Low (ON) – Rear wiper operates at a
continuous low-speed.

09
Push the lever forward to activate the
rear washer. The rear wiper will operate
several times.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
16
MIST
OFFAUTO LO
HI
INT
ON
01
02
04
06
07
08
05
09
03
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 169/24/13 11:43 AM

17
Automatic Climate Controls
01 AUTO BUTTON

The auto mode may be used year-round. Press the AUTO button to turn the system on
and the system will automatically control the inside temperature (autom\
atic cooling
and/or dehumidified heating), air flow distribution and fan speed.
02 CLIMATE BUTTON

Press the CLIMATE button to adjust your automatic climate controls using the climate
settings on the control panel display screen.
03 DRIVER’S SIDE TEMPERATURE CONTROL BUTTONS

Press the driver’s side temperature control buttons up for warmer air or down
for
cooler air.
04 DRIVER’S SIDE MANUAL AIR FLOW CONTROL BUTTON

Press the driver’s side manual air flow control button to manually con\
trol the driver’s
side air flow modes.

The following air flow indicator modes will display on the control panel\
display screen:

Air flows from the center and side vents.

Air flows from the center, side and foot vents.

Air flows mainly from the foot vents.

Air flows from the defroster and foot vents.
05 PASSENGER’S SIDE TEMPERATURE CONTROL BUTTONS

To manually adjust the passenger’s side temperature, press the passen\
ger’s side
temperature control buttons up
for warmer air or down
for cooler air.
06 DUAL BUTTON

Press the DUAL button to turn the passenger’s side temperature controls on or off. This
will allow the passenger’s side temperature to be adjusted independen\
tly from the
driver’s side by pressing the passenger’s side temperature control\
buttons.
0406
0809120701101102
0305
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 179/24/13 11:43 AM

first drive features
18
07 FAN SPEED CONTROL BUTTONS


Press the left button to decrease the fan speed or press the right
button to
increase the fan speed.
08 DEFROSTING/DEFOGGING FRONT AND SIDE WINDOWS


Press the defroster control button
to turn the system on. The A/C automatically turns
on when the defroster mode is selected. This feature removes humidity fr\
om the air.


To defrost the front and side windows, set the temperature controls
03 and fan
speed controls 07 to their maximum settings.
09
DEFROSTING REAR WINDOW AND OUTSIDE MIRRORS

Push the rear window defroster switch
REAR to turn the system on or off.
This function automatically turns off after approximately 15 minutes.
10 REAR AIR CONDITIONER


To control the rear automatic air conditioning
system with the front air conditioner control
panel, press the REAR button.


When the rear automatic air conditioning system
is on, the indicator light on the REAR button will
illuminate and the front display will switch to the
rear air conditioner screen. Use the driver
temperature and fan speed buttons to adjust settings.

To adjust the front air conditioning system, press the REAR button again.

To turn off the rear automatic air conditioning system from the front co\
ntrols, press the
REAR button until the Rear Air-conditioning screen is displayed. Then, press the
OFF button
12.

The rear passenger controls are unavailable when Rear Air-conditioning screen is
shown on the front display.
11 INTAKE AIR CONTROL BUTTON


Press the intake air control button to recirculate interior air inside the vehicle. The
indicator light on the button will illuminate. This system is used to a\
void certain
outside odors and helps to adjust the inside vehicle temperature more ef\
fectively.


The air recirculation mode cannot be activated when the climate control \
system is in the
front defrost mode

or front defrost and foot vent mode
.


Press the intake air control button again to change the air circulation from the
intake air to the outside air. The
indicator light on the button will turn off.
12 OFF BUTTON


Press the OFF button to turn the climate control system off.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4\
) ” of your
Owner’s Manual.
1591600_14b_Infiniti_QX60_HEV_QRG_092413.indd 189/24/13 11:43 AM