lights INFINITI QX70 2015 Quick Reference Guide

6
first drive features
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock
or unlock your vehicle, open your liftgate and start
the engine.

It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).

The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.

To lock the vehicle, push either door handle request
switch

1 once or press the
button
2 on the key fob.

To unlock the vehicle, perform one of the following procedures:
•
Push either door handle request switch

1 once; the
corresponding door will unlock. Push the door handle
request switch
1 again within 1 minute; all other
doors will unlock, or
•
Press the

button
3 on the key fob to unlock the driver’s
side door. Press the
button again; all other doors will unlock.

To open the liftgate, press the button
4 for more than 1 second.

The Intelligent Key can also be used to activate the panic alarm by pres\
sing and holding
the

button
5 for more than 1 second. Once activated, the panic alarm and headlights
will stay on for a period of time.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE

If the battery in the Intelligent Key is almost dis-
charged, the guide light

6 of the Intelligent Key port
blinks and the Intelligent Key insertion indicator 7
is displayed in the vehicle information display.

To start the engine under these circumstances, insert
the Intelligent Key into the key port with the keyring
side facing backward until it latches into place. Then
push the ignition switch to start the engine.

To remove the Intelligent Key from the port, push
the ignition switch to turn the engine off and then
pull the Intelligent Key out of the port.

The Intelligent Key port does not charge the
Intelligent Key battery. If you see the Intelligent
Key warning light

8, replace the battery in the
Intelligent Key.

Do not insert the mechanical key or other objects into
the key port because it will damage the key port.
For more information, refer to the “Pre-driving checks and adjustments
(section 3)”, “Starting and driving (section 5)” and the “Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
1
2
3
4
5
6
F E
7
8
1807402_15b_Infiniti_QX70_QRG_100114.indd 610/1/14 4:18 PM

9
Starting/Stopping the Engine
It is important to make sure the INFINITI Intelligent
Key is with you (that is, in your pocket or purse).

Depress the brake pedal.
• If the brake pedal is not depressed, pushing the
ignition switch once enters the ACC mode.
• If the ignition switch is pushed a second time, the
vehicle will enter the ON mode.

Move the shift lever to the P (PARK) position.

Push the ignition switch to start the engine.
TURNING THE ENGINE OFF

Move the shift lever to the P (PARK) position and apply the parking brake.

Press the ignition switch START/STOP button to turn the engine off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
Headlight Control Switch
Turn the headlight control switch to the position
1 to turn on the front parking, side
marker, tail, license plate and instrument panel
lights. Turn the switch to the
position
2 to
turn on the headlights.
AUTOLIGHT SYSTEM

The autolight system will automatically turn the headlights on when it i\
s dark and off when
it is light. The system will keep the headlights on for a period of time\
after you turn the igni -
tion off and all the doors are closed.

To activate the autolight system, turn the headlight control switch to t\
he AUTO position
3
then push the ignition switch to ON. To deactivate the autolight system, turn the headlight
control switch to the OFF,
position 1 or
position
2.
HIGH BEAM SELECT

Push the headlight control switch forward
4 to
select the high beam function. The blue indicator
light
illuminates in the instrument panel. Pull
the headlight switch back to the original position to
select the low beam. The blue indicator light
will extinguish.

Pull and release the headlight control switch
5 to
flash the headlight high beams on and off.
4
5
1
2
3
1807402_15b_Infiniti_QX70_QRG_100114.indd 910/1/14 4:18 PM

10 FOG LIGHT SWITCH


The headlights must be on and the low beams

selected for the fog lights to operate.


Turn the switch (inside collar) to the position
6
to turn the fog lights on.


Turn the switch (inside collar)
to the OFF position to
turn the fog lights off.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
first drive features
Windshield Wiper and Washer Switch
Move the lever to one of the following positions to
operate the windshield wipers:

1 Mist (MIST) – One sweep operation of the
front wipers.

2 Auto (AUTO) (if so equipped) – Operates
the rain-sensing wipers intermittently. To
increase or decrease wiper sensitivity twist the
control ring
3 .

4 Low (LO) – Front wipers operate at a
continuous low-speed.

5 High (HI) – Front wipers operate at a
continuous high-speed.

6 Front washer – Pull the lever toward you
to activate the front washer. The front wipers
will operate several times.
REAR WINDSHIELD WIPER AND WASHER

7 Intermittent (INT) –
Rear wiper operates intermittently.

8 Low (ON) – Rear wiper operates at a
continuous low-speed.

9 Rear washer – Push the lever forward to
activate the rear washer. The rear wiper will
operate several times.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.2
6
INT
ON
MIST OFF
AUTO
LO
HI1
2
4
5
3
69
7
8
1807402_15b_Infiniti_QX70_QRG_100114.indd 1010/1/14 4:18 PM

15
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
1 for less
than 1.5 seconds. The CRUISE indicator light 2
will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch
3 and
release it. Cruise control will be set to the
desired speed.

Press the distance button
4 repeatedly to change
the set distance between long, middle and short.

When a vehicle is not detected ahead of you in
the lane, the set distance and set vehicle speed
indicator lights will illuminate

5 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance and set
vehicle speed indicator lights will illuminate

6 in
set mode.

To reset at a faster cruising speed, push and hold
the ACCEL/RES switch

7. When the vehicle attains the desired
speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET
switch

3. Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
8 or tap the brake pedal. The set
vehicle speed indicator 5 will extinguish.

To turn off cruise control, press the CRUISE ON/OFF button
1. The CRUISE indicator
light
2 in the instrument panel will extinguish.
To set the conventional (fixed speed) cruise control mode:

While cruise control is off, press the CRUISE ON/OFF
button
1 and hold it down for more
than 1.5 seconds. The CRUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control should be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off\
and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
87
3
4
1
25
6
1807402_15b_Infiniti_QX70_QRG_100114.indd 1510/1/14 4:18 PM

24
HOMELINK
HomeLink® Universal Transceiver
The HomeLink® Universal Transceiver can learn and consolidate the functions of up to \
three different hand-held transmitters, operating items such as garage d\
oors, property
gates, outdoor and indoor lights or alarm systems.

To program the HomeLink® Universal Transceiver:
• Position the handheld transceiver 1-3 in (26-76 mm) away from the Home\
Link surface,
keeping the HomeLink indicator light in view.
• Press and hold the desired HomeLink button and the handheld transmitter \
button
simultaneously until the HomeLink indicator light flashes slowly and the\
n rapidly.
• Both buttons may be released when the indicator light flashes rapidly.

To verify the programing is complete, press and hold the HomeLink button\
and observe the
indicator light:
• A solid, continuous light indicates the programing is complete and the H\
omeLink button
will activate your device.
• A blinking light that turns to a solid, continuous light after 2 seconds\
indicates additional
steps are required to complete the programing.

An additional person may make the remaining steps easier. To complete th\
e
programing process:
• At the receiver of the device that you are programing to the HomeLink bu\
tton, press
and release the learn or smart button (the name may vary by manufacture\
r but it is
usually located near where the hanging antenna wire is attached to the u\
nit). You have
approximately 30 seconds to initiate the following step.
• Press and hold the programed HomeLink button for 2 seconds and release.

You may have to repeat the previous 2 steps up to 3 times to complete th\
e programing
process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
system guide
1807402_15b_Infiniti_QX70_QRG_100114.indd 2410/1/14 4:19 PM