sensor INFINITI QX80 2014 Quick Reference Guide

4
Around View® Monitor with Moving Object Detection (MOD)
Moving Object Detection (MOD) operates only with
the Around View® Monitor activated.



•


To temporarily turn the system on or off select

the “MOD” key on the bottom of the control
panel display.
When the CAMERA button is pressed and the vehicle
speed is less than 6 MPH (10 km/h) or the shift lever
is moved to the R (REVERSE) position, the Information
Display Screen will automatically change to view the area surrounding th\
e vehicle.
With the Around View® Monitor displayed, the corner sonar system can detect objects
near the vehicle and warn the driver by sounding a tone and showing an i\
ndicator in
the display screen.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4\
)” of your
Owner’s Manual.
new system features
Lane Departure Prevention (LDP) System
(if so equipped)
This system will help you return the vehicle to the
center direction of the traveling lane by applying
brake control to the left or right wheels individually
(for a short period of time).
For more information, refer to the “Starting and driving (section 5)” of your
Owner’s Manual.
Blind Spot Warning (BSW) and Blind Spot Intervention™ (BSI)
(if so equipped)
The Blind Spot Warning (BSW) system alerts the
driver when another vehicle moves into the vehicle’s
blind spot area.
An indicator light near the outside mirror will
illuminate if the radar sensors detect a vehicle in the
detection zone.
The Blind Spot Intervention™ (BSI) system can assist
the driver in returning the vehicle to the center of the
traveling lane by applying individual brake pressure
to the left or right wheels for a short period of time.
The indicator light will first illuminate in orange and
then turn green before turning off. This indicates
that the Blind Spot Warning (BSW) and Blind Spot
Intervention (BSI) systems are operational.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
1591592_14b_Infiniti_QX80_QRG_093013.indd 49/30/13 9:35 AM

15
Windshield Wiper and Washer Switch
Move the lever to the following positions to operate
the windshield wipers:
01 Mist
(MIST) - One sweep operation of the
front wipers.
02 Auto
(AUTO) - Operates the rain-sensing
auto front wiper system. The rain sensor
sensitivity level can be adjusted by twisting
the time control ring
03 to increase or
decrease wiper sensitivity.
04 Low
(LO) - Front wipers operate at a continuous
low speed.
05 High (HI) - Front wipers operate at a continuous
high speed.
06 Pull the lever toward you to activate the
front washer. The front wipers will operate
several times.
REAR WINDSHIELD WIPER AND WASHER
07 Intermittent (INT) - Rear wiper operates
intermittently.
08 Low (ON) - Rear wiper operates at a
continuous low speed.
09 Push the lever forward to activate the
rear washer. The rear wiper will operate
several times.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
0301
02
04
05
INT07
ON08
MIST
OFF
AUTO LOHI
06
09
TYPE B (if so equipped)
1591592_14b_Infiniti_QX80_QRG_093013.indd 159/30/13 9:36 AM

20
first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
The Intelligent Cruise Control (ICC) system
automatically maintains a selected distance from
the vehicle traveling in front of you according to that
vehicle’s speed (up to the set speed) or at the set
speed when the road ahead is clear.
This system may not function properly due to
road conditions when direct sunlight, rain, mud,
snow or other road spray cause the sensor to
become blocked.
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE
To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button
01 for less than 1.5
seconds. The indicator light
02 will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch 03 and release it. Cruise control
will be set to the desired speed.
Press the distance button 04 repeatedly to change the set distance
between long, middle, and short.
When a vehicle is not detected ahead of you in the lane, the set distanc\
e and set vehicle
speed indicator lights will illuminate
05 in set mode.
When a vehicle is detected ahead of you in the lane, t he vehicle ahead detection, set
distance, and set vehicle speed indicator lights will illuminate
06 in set mode.
TO SET CONVENTIONAL FIXED SPEED CRUISE CONTROL MODE:
While cruise control is off, press the CRUISE ON/OFF button and hold it down for more than
1.5 seconds. The CRUISE indicator light will illuminate.
Accelerate to the desired speed.
Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control should be set to the desired speed.
TO SWITCH BETWEEN THE TWO CRUISE CONTROL MODES:
When one of the two cruise modes is in use, you must turn the system off\
, and then turn it
on again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
03
01
04
0205
06
1591592_14b_Infiniti_QX80_QRG_093013.indd 209/30/13 9:36 AM