display INFINITI QX80 2017 Navigation Manual

MAP SYMBOLS
This navigation system uses symbols to display facilities.
3. Map settings
3-21

3. Map settings
3-22
ROAD COLOR
The road types are differentiated by colors.
Freeway:
(Red or light red (zoomed in))
Main road:
(Brown or dark yellow)
Narrow street:
(Gray)
Road with incomplete map data:
(Dark green)
TRAFFIC INFORMATION ON MAP
With a subscription to the NavTraffic
service, traffic information is displayed.
“Viewing available traffic information”
(page 7-16)
Free Flow:
(Green)
Moderate traffic:
(Yellow)
Heavy traffic:
(Red)
Section affected by serious traffic event:
(Purple)
The following traffic information icons may be displayed
: Accident
: Closed road
: Information
: Road work
: Slippery road
: Weather
: Incident

4. Setting destination
4-4
2. Enter the name of the city, highlight[List] and push .
A list screen is displayed.
INFO:
.The same screen will be displayed when a location is searched by “Street Ad-
dress”, “Freeway Entrance/Exit” or“In-
tersection” , and when [City] is
highlighted and is pushed.
“Finding address” (page 4-4)
.Highlight [Last 5 Cities] and push
to display the last 5 cities
recently set as destinations.
3. Highlight the city of the destination from the list and push .
INFO:
There are instances when the destination
list screen number will be less than what
was shown in the matches screen, but this
is due to the system automatically deter-
mining that some destinations are dupli-
cates. The“Matches” destinations includes
duplicates. When the [LIST] is highlighted
and is pushed, the system does a
further analysis to remove the duplicates,
so the number is sometimes less.
FINDING ADDRESS
When the address of the destination is
known, use the following method to enter
the address and then have the system
calculate a route. A location near the
preferred destination can also be searched
by entering the house number if the map
data contains the relevant data.
1. Push , highlight [Street Address]
and push . A character input
screen is displayed.

2. Enter the house number, highlight [OK]and push . If the house number
is not available, highlight [No House #]
and push . A street name input
screen is displayed.
3. Enter the name of the street. After
finishing the entry, highlight [List] and
push . A list of streets is
displayed.
INFO:
When [City] is highlighted and is
pushed, a city can be specified by typing the
city name.
“Specifying city” (page 4-3)
4. Highlight the correct street of the
destination from the list and push
.
INFO:
In some cases, when a street name has
been entered, the number of matching
destinations in the “Matches”column may
be different from the number displayed on
the list screen. If this occurs, enter more
characters to further reduce the number of
matches.
5. The entire route is shown on the map. Highlight [Start] after confirming the
location of the displayed destination,
and push . The system sets the
destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
Voice command
1. Push >located on the steering
wheel.
2. After the tone sounds, speak a com- mand.
To set the destination from a street
address:
“Navigation”“ Address”(Standard
Mode)
“Address” (Alternate Command Mode)
4. Setting destination
4-5

4. Setting destination
4-6
INFO:
When using a voice command to set a street
name, it is recommended that the complete
street name is stated.
Examples:Correct input –North Elm Street
East Jefferson Boulevard
Incorrect input –Elm Street
East Jefferson
FINDING PLACE
There are 3 methods that can be used to
set the destination to places of interest:
typing the name, choosing a category or
selecting a ZAGAT reviewed location. To
help improve searching, different start
points can be chosen to search from such
as near current location, near the destina-
tion or city center.
Finding nearby place
1. Push .
2. Highlight [Places] and push .
3. Highlight the preferred nearby category
from the list and push .
A list screen is displayed.
INFO:
Highlight [Customize Nearby Places] to
customize the 5 nearby categories to show the categories that you frequently use.
4. Highlight the preferred destination
from the list, and push . The
position of the selected location is
displayed in the preview on the right
side of the screen.
INFO:
.A maximum of 100 facilities can be displayed on the list screen.
.To search for facilities along your route, select [Show Along Route].

5. The entire route is shown on the map.Highlight [Start] after confirming the
location of the displayed destination,
and push . The system sets the
destination to the selected location and
starts calculating a route.
INFO:
.
If there is a route already set, the newly
selected location can substitute a previously
set destination or can be added to a route
already set.
.To review the destination location again,
highlight [Move Location] and push
.
Other settings:
The destination can also be set by pushing
in the current or scrolled location
map screen and selecting [Nearby Places].
Voice command
1. Push >located on the steering
wheel.
2. After the tone sounds, speak a com- mand.
To display the nearby category list and
select the destination from it:
“Navigation”“ Places”(Standard Mode)
“Places” (Alternate Command Mode)
Searching by other methods
1. Push.
2. Highlight [Places] and push .
3. Highlight [All Categories or Name] and
push .
4. Setting destination
4-7

4. Setting destination
4-8
4. Set the narrowing down conditions forthe landmarks and push .
INFO:
Highlight [Change Region] and push
to change the region. A screen for
selecting a region is displayed.
“Changing region” (page 4-3)
INFO:
If [Select a City] is highlighted and
is pushed, a city name input screen is
displayed. Specify the city to be searched
before narrowing down the categories.
“Specifying city” (page 4-3)
5. Highlight the main category from the
list and push .
INFO:
To select a category by directly inputting the
category name, highlight [Category Search]
and push. The category name input
screen is displayed.
6. Highlight the subcategory and push .
INFO:
Subcategories may not exist depending on
the category that is selected.

7. Enter the name of the destinationfacility and highlight [List], and then
push .
The facility list is displayed.
INFO:
.It is not necessary to enter the facility name completely. It is also possible to
display the list screen only by high-
lighting [List] without entering the facil-
ity name and pushing .
.The number of narrowed down points are
displayed in the “Matches”column.
.Up to two keywords (part of the facility
name) can be entered by highlighting
[AND Search] and pushing after
entering the first facility name.
INFO:
The facility name can also be entered
directly by highlighting [Choose Name] on
the main category list screen and pushing

8. Highlight the preferred destination from the list, and push .
INFO:
.By highlighting [Sort] and pushing
, options can be sorted from
[By Name] or [By Dist.]. When selecting
[By Dist.], the position of the selected
location is displayed in the preview on
the right side of the screen.
.In some cases, when a facility name has
been entered, the number of matching
destinations in the “Matches”column
may be different from the number displayed on the list screen. If this
occurs, enter more characters to further
reduce the number of matches.
.The search conditions can be changed by
highlighting [Refine] and pushing
.
9. The entire route is shown on the map.
Highlight [Start] after confirming the
location of the displayed destination
and push . The system sets the
destination to the selected location and
starts calculating a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
4. Setting destination
4-9

4. Setting destination
4-10
Searching for restaurant using ZA-
GAT
1. Push.
2. Highlight [Places] and push .
3. Highlight [ZAGAT] and push.
4. Highlight the preferred state and push
. A list screen is displayed.
5. Highlight the preferred city and push
. A list screen is displayed.
6. Highlight [RESTAURANT] and push. A list screen is displayed.
7. Highlight the preferred category andpush . A list screen is dis-
played.
8. Highlight the preferred sorting order and push . A list screen is
displayed.

9. Highlight the preferred destination fa-cility from the list, and then push
.
INFO:
.By highlighting [Sort] and pushing, sorting options can be selected
to re-sort the list.
.The search conditions can be changed by highlighting [Refine].
.By highlighting [Ratings] and pushing, an explanation of the ZAGAT
ratings can be displayed.
10. The entire route is shown on the map. Highlight [Start] after confirming the
location of the displayed destination
and pushing . The system sets
the destination to the selected location
and starts calculating a route.
INFO:
Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc.
“Procedures after setting destination”
(page 5-2)
*C2009 Zagat Survey, LLC. Zagat Survey is
a registered trademark of Zagat Survey,
LLC.
SETTING HOME AS DESTINATION
The home location can be set as the
destination to which the system calculates
a route. This function is especially useful
when searching for a route to return to the
home location.
1. Push .
2. Highlight [Home] and push .
3. The home location is displayed, and the
system sets the home location as the
destination.
4. Setting destination
4-11