light ISUZU AXIOM 2002 Service Repair Manual

METER AND GAUGE8E±5
Connector A
TerminalFunction
1Ð
2Intelligent suspension indicator light
3TOD indicator light ªRearº
4Ð
5TOD indicator light ªAUTOº
6Ð
7TOD indicator light ªFrontº
8A/T shift indicator light ª3º
9A/T shift indicator light ªDº
10A/T shift indicator light ª2º
11SRS ± air bag warning light
12Ground
13Battery
14Stater switch
15A/T oil temperature warning light
16Seat belt indicator light
17Charge warning light
18Ð
19Ð
20Ð
21A/T shift indicator light ªLº
22ABS warning light
23Ð
24Ð
25Reduced power warning light
26Oil pressure warning light
27Check trans warning light
28MIL(check engine) warning light
29Check TOD
30Engine coolant temperature gauge
Connector B
TerminalFunction
1A/T shift indicator light ªRº
2A/T shift indicator light
3A/T shift indicator light ªNº
4A/T shift indicator light ªPº
5Illumination light
6Engine revolution pulse
7Speed sensor pulse
8Turn signal indicator light (LH)
9Brake warning light
10High beam indicator light (+)
11High beam indicator light (±)
12Turn signal indicator light (RH)
13Turn signal indicator light
14Ð
15Illumination light
16Ground
Connector C
TerminalFunction
1Starter switch
2Ð
3Fuel gauge
4Low fuel warning light
5Cruise set indicator light
6Ð
7Ð
8Ð
9Ð
10Sport mode indicator light
11Ð
12Winter drive indicator light
13Power drive indicator light
14Ð

8E±6METER AND GAUGE
Removal
1. Disconnect the battery ground cable.
2. Remove the Dash Side Trim Panel ±LH.
3. Remove the lower cover Assembly(2).

Refer to
Instrument Panel Assembly in Body
Structure
section.
4. Remove the meter cluster Assembly(1).

Refer to
Instrument Panel Assembly in Body
Structure
section.
821R200020
5. Remove the meter assembly(3).

Remove four fixing screws.

Disconnect the meter connectors.
825RW197
CAUTION: The removed meter assembly should be
placed upright or with its face side up.
Installation
To install, follow the removal steps in the reverse order.
Warning Light Bulb and Indicator Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the meter assembly.

Refer to
Meter Assembly in this section.
3. Remove the bulb.

Hold the bulb socket by hand, rotate it
counterclockwise and pull it out.
Installation
To install, follow the removal steps in the reverse order.

METER AND GAUGE8E±7
A/T Shift Indicator Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Pry up the bended portions(2) of the metal cover(1).
821RY00060

8F±15 BODY STRUCTURE
Front Fender Panel
Parts Location
605R200001
Legend
(1) Antenna Assembly
(2) Rocker Cover Assembly
(3) Front Turn Signal Light Assembly(4) Front Bumper Fascia Assembly
(5) Inner Liner
(6) Front Fender Panel

8F±16BODY STRUCTURE
Removal
1. Disconnect the battery ground cable.
2. Remove the front bumper fascia assembly.

Refer to
Front Bumper in this section.
3. Remove the front turn signal light assembly.

Remove the fixing screw and disconnect the
connector.
610R200008
4. Remove the rocker cover assembly.

Refer to
Rocker Cover Assembly in Exterior/Interior
Trim section.
5. Remove the inner liner.
647RY00003
6. Remove the antenna assembly.

Refer to
Rod Type Antenna in Entertainment
section.
7. Remove the front fender panel (1).

Remove the eight fixing bolts.
8. Remove the engine compartment upper extension
(2).
614R200002
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Tighten the front fender panel fixing bolts to the
specified torque.
Torque : 7 N´m (61 lb in)
2. Check the fender and front door (1).
Clearance: 5.0 mm (0.196 in)
Height (step): Flush
610R200009

8F±33 BODY STRUCTURE
Removal
CAUTION: F o r p recautions on installation or
removal of SRS ± air bag system, refer to
Supplemental Restraint System (SRS) ± AIR BAG in
Restraint section.
1. Disconnect the battery ground cable.
2. Pry the knee pads (4).
3. Remove the cluster upper cover (1) and connectors.
4. Remove the center cluster assembly (2).

Remove six screws and pull out the cluster at the six
clip positions.

Disconnect the cigarette lighter (6), ash tray (5)
illumination and hazard switch (3) connectors.
740R200008
5. Remove the display unit.

Remove the four fixing screws and connectors.
6. Remove the audio kit.

Remove the four fixing screws and connectors.
7. Remove the front and rear consoles.

Refer to
Consoles in Exterior/Interior Trim section.
8. Remove the dash side trim panels.

Remove the sill plates, then remove the trim panels.
9. Remove the glove box.

Remove the two fixing screws.
470RW002
10. Remove the instrument panel driver lower cover
assembly.

Remove the engine hood opener two fixing screws
and another one fixing screw.
After four clips are pried, disconnect switch
connector and duct.
610R200007
11. Remove the meter cluster assembly.

Remove the six fixing screws and switch
connectors.
12. Remove the meter assembly.

Remove the four fixing screws and disconnect the
connectors.
13. Remove the driver knee bolster assembly.

Remove the six fixing bolts and screw.
14. Remove the instrument panel assembly.
CAUTION: F o r p recautions on installation or
removal of SRS ± air bag system, refer to
Supplemental Restraint System (SRS) ± AIR BAG in
Restraint section.

8F±36BODY STRUCTURE
4. Remove the upper and lower hinge bolts.

Position a wood block under the door for protection
and support the door assembly with hands during
removal or installation.
635R200013
5. Remove the door harness connector.

Pull the door harness grommet out in order to
disconnect the harness connector.
630R200012
6. Remove the front door assembly.
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Align the door fitting to the body.

Check the fender and front door (1).
Clearance: 5.0 mm (0.196 in)
Height (step): Flush

Check the front door and rear door (2).
Clearance: 5.0 mm (0.196 in)
Height (step): Flush

Check the rear door and body (3).
Clearance: 5.0 mm (0.196 in)
Height (step): Flush
Adjust clearance with door hinges.
Adjust height (step) by tapping on the fender lightly
with a rubber hammer.
610R200005
2. Tighten the door hinge bolts to the specified torque.
Torque : 34 N´m (25 lb ft)
3. Tighten the door check arm bolt and nuts to the
specified torque.
Torque : 9 N´m (78 lb in)

8F±39 BODY STRUCTURE
Front Window Regulator, Glass and Glass Run
Parts Location
635R200012
Legend
(1) Glass
(2) Glass Run
(3) Door Mirror Assembly
(4) Door Mirror Cover
(5) Tweeter
(6) Speaker Spacer
(7) Speaker Assembly
(8) Inner Waist Seal
(9) Door Trim Panel
(10) Power Window Switch
(11) Inside Lock Bracket(12) Inside Handle
(13) Pull Box
(14) Courtesy Light
(15) Pull Box Bracket
(16) Waterproof Sheet
(17) Front Door Panel
(18) Door Lock Assembly
(19) Door Lock Cylinder
(20) Outside Handle
(21) Window Regulator
(22) Outer Waist Seal

8F±40BODY STRUCTURE
Removal
1. Disconnect the battery ground cable.
2. Remove the pull box.

Remove the one fixing screw.
635R200004
3. Remove the power window switch (1).

Pull the power window switch and remove the
connector.
635R200002
4. Remove the inside handle.

Open the screw cover (1) and remove the screw.

Disconnect the cable.
635R200003
5. Remove the door mirror cover.
6. Remove the trim panel at the 8 clip positions (1).

Disconnect the tweeter and courtesy light
connectors.
635R200005

8F±41 BODY STRUCTURE
7. Remove the inner waist seal.
8. Remove the tweeter.
9. Remove the courtesy light.
10. Remove the pull box bracket.
11. Remove the inside lock bracket.

Disconnect the cable.
12. Remove the speaker (2) and speaker spacer (1).

Disconnect the speaker connector (3).
890R200028
13. Remove the waterproof sheet.
14. Remove the outer waist seal.

Remove the rear side screw and pull the outer waist
seal upward.
15. Remove the window glass.

Operate the requlator (power window switch) to
adjust the glass height and expose the access hole.
Remove the 2 bolts fixing the bottom channel and
the requlator. Remove the glass.
631R200001
631R200002
16. Remove the window regulator.

Remove the 7 fixing bolts and disconnect the
window regulator motor harness connector.
17. Remove the glass run.

Pull the glass run (6) from the door frame.
631RS007
Installation
To install, follow the removal steps in the reverse order,
noting the following points:
1. Check to see that the window regulator operates
smoothly and the glass opens and closes properly.
2. Install the waterproof sheet tightly against the door
panel.
3. Tighten the window regulator assembly fixing bolts to
the specified torque.
Torque : 6 N´m (52 lb in)