brake pads ISUZU AXIOM 2002 Service Repair Manual

0A±9
GENERAL INFORMATION
Lifting Instructions
CAUTION:

If a lifting device other than the original jack is
used, it is most important that the device be
applied only to the correct lifting points. Raising
the vehicle from any other point may result in
serious damage.
When jacking or lifting a vehicle at the frame side
rail or other prescribed lift points, be certain that
lift pads do not contact the catalytic converter,
brake pipes or cables, or fuel lines. Such contact
may result in damage or unsatisfactory vehicle
performance.
Lifting Points and Supportable Point Locations
C00RX002
Lifting Point: Front

When using a floor jack, lift on the Convex portion of
the skid plate.
545RS001

0B±5 MAINTENANCE AND LUBRICATION
Explanation of Complete Vehicle
Maintenance Schedule
Brief explanations of the services listed in the preceding
Maintenance Schedule are presented below.
Replace all questionable parts and note any necessary
repairs as you perform these maintenance procedures.
Front and Rear Axle Lubricant
Replacement
Check the lubricant level after every 7,500 miles (12,000
km) of operation and add lubricant to level of filler hole if
necessary.
Replace the front and rear axle lubricant at 15,000 miles
(24,000 km) and 30,000 miles (48,000 km) and after
every 30,000 miles (48,000 km) of operation thereafter.
Air Cleaner Element Replacement
Replace the air cleaner under normal operating
conditions every 30,000 miles (48,000 km).
Operation of the vehicle in dusty areas will necessitate
more frequent replacement.
Spark Plug Replacement
Replace the plugs at 100,000 miles (160,000 km)
intervals with the type specified at the end of this section.
Cooling System Service
Drain, flush and refill system with new engine coolant.
Refer to
ªRecommended Fluids and Lubricantsº in this
section, or ENGINE COOLING (SEC.6B).
Timing Belt Replacement
Replacement of the timing belt is recommended at every
100,000 miles (160,000 km).
Failure to replace the timing belt may result in serious
damage to the engine.
Valve Clearance Adjustment
Incorrect valve clearance will result in increased engine
noise and reduced engine output.
Retorque the camshaft bracket bolts before checking and
adjusting the valve clearance.
Check and adjust the valve clearance whenever
increased engine noise is heard.
Tire Rotation
Rotate tires every 7,500 miles (12,000 km).
Front Wheel Bearings Lubricant
Replacement (Vehicles Produced Before
July/31/2001)
Clean and repack the front wheel bearings at 30,000
miles (48,000 km) intervals.
Refer to DRIVE SHAFT SYSTEM (SEC. 4C).
Front Wheel Bearings Check (Vehicles
Produced After Aug./1/2001)
Inspect hub unit bearing at every 60,000 miles (96,000
km).
If there is abnormal condition, replace hub unit bearing.
Radiator Core and Air Conditioning
Condenser Cleaning
Clean the front of the radiator core and air conditioning
condenser, at 60,000 miles (96,000 km) intervals.
Fluid Level Check
A fluid loss in any system (except windshield
washer) may indicate a problem. Repair the system
at once.
Engine oil level
Check level and add if necessary. The best time to check
the engine oil level is when the oil is warm. After stopping
the engine with the vehicle on a level surface, wait a few
minutes for the oil to drain back to the oil pan. Pull out the
oil level indicator (dipstick). Wipe it clean and push the oil
level indicator back down all the way. Pull out the oil level
indicator, keeping the tip down, and look at the oil level on
it.
Add oil, if needed, to keep the oil level above the ªADDº
mark and between the ªADDº and ªFULLº marks in the
operating range area. Avoid overfilling the engine since
this may cause engine damage. Push the oil level
indicator back down all the way after taking the reading.
If you check the oil level when the oil is cold, do not run the
engine first. The cold oil will not drain back to the pan fast
enough to give a true oil level.
Engine coolant level and condition
Check engine coolant level in the coolant reservoir and
add engine coolant if necessary. Inspect the engine
coolant and replace it if dirty or rusty.
Windshield washer fluid level
Check washer fluid level in the reservoir and add if
necessary.
Power steering system reservoir level
Check and keep at the proper level.
Brake master cylinder reservoir level
Check fluid. Keep fluid at proper level. A low fluid level can
indicate worn disc brake pads which may need to be
serviced.
Hydraulic clutch system
Check fluid level in the reservoir. Add fluid as required.
Battery fluid level
Check fluid level in the battery.
Fluid Leak Check
Check for fuel, water, oil or other fluid leaks by looking at
the surface beneath the vehicle after it has been parked
for a while. Water dripping from the air conditioning
system after use is normal. If you notice gasoline fumes or
fluid at any time, locate the source and correct it at once.
Engine Oil and Oil Filter Replacement
Always use API SE, SF, SG, SH or ILSAC GF±1 quality
oils of the proper viscosity.
When choosing an oil, consider the range of
temperatures the car will be operated in before the next oil
change. Then, select the recommended oil viscosity from
the chart.

0B±6MAINTENANCE AND LUBRICATION
Always change the oil and the oil filter as soon as possible
after driving in a dust storm.
Engine Cooling System Inspection
Inspect the coolant/anti±freeze. If the coolant is dirty or
rusty, drain, flush and refill with new coolant. Keep coolant
at the proper mixture for proper freeze protection,
corrosion inhibitor level and best engine operating
temperature. Inspect hoses and replace if cracked,
swollen or deteriorated. Tighten the hose clamps if
equipped with screw±type clamps. Clean outside of
radiator and air conditioning condenser. Wash filler cap
and neck. To help ensure proper operation, a pressure
test of both the cooling system and the cap is also
recommended.
Exhaust System Inspection
Visually inspect the exhaust pipes, muffler, heat shields
and hangers for cracks, deterioration, or damage.
Be alert to any changes in the sound of the exhaust
system or any smell of fumes. These are signs the system
may be leaking or overheating. Repair the system at
once, if these conditions exist. (See also ªEngine Exhaust
Gas Safetyº and ªThree Way Catalytic Converterº in the
Owner's manual.)
Fuel Cap, Fuel Lines, and Fuel Tank
Inspection
Inspect the fuel tank, the fuel cap and the fuel lines every
60,000 miles (96,000 km) for damage which could cause
leakage.
Inspect the fuel cap and the gasket for correct sealing and
physical damage. Replace any damaged parts.
Drive Belt Inspection
Check the serpentine belt driving for cracks, fraying,
wear, and correct tension every 30,000 miles (48,000
km). Replace as necessary.
Wheel Alignment, Balance and Tires
Operation
Uneven or abnormal tire wear, or a pull right or left on a
straight and level road may show the need for a wheel
alignment. A vibration of the steering wheel or seat at
normal highway speeds means a wheel balancing is
needed. Check tire pressure when the tires are ªcoldº
(include the spare).
Maintain pressure as shown in the tire placard, which is
located on the driver's door lock pillar.
Steering System Operation
Be alert for any changes in steering operation. An
inspection or service is needed when the steering wheel
is harder to turn or has too much free play, or if there are
unusual sounds when turning or parking.
Brake Systems Operation
Watch for the ªBRAKEº light coming on. Other signs of
possible brake trouble are such things as repeated pulling
to one side when braking, unusual sounds when braking
or between brake applications, or increased brake pedaltravel. If you note one of these conditions, repair the
system at once.
For convenience, the following should be done when
wheels are removed for rotation: Inspect lines and hoses
for proper hookup, bindings, leaks, crack, chafing etc.
Inspect disc brake pads for wear and rotors for surface
condition.
Inspect other brake parts, including parking brake drums,
linings etc., at the same time. Check parking brake
adjustment.
Inspect the brakes more often if habit or conditions
result in frequent braking.
Parking Brake and Transmission Park
Mechanism Operation
Park on a fairly steep hill and hold the vehicle with the
parking brake only. This checks holding ability. On
automatic transmission vehicles, shifting from ªPº
position to the other positions cannot be made unless the
brake pedal is depressed when the key switch is in the
ªONº position or the engine is running.
WARNING: B E F O R E C H E C K I N G T H E S TA R T E R
SAFETY SWITCH OPERATION BELOW, BE SURE TO
HAVE ENOUGH ROOM AROUND THE VEHICLE.
THEN FIRMLY APPLY BOTH THE PARKING BRAKE
AND THE REGULAR BRAKE. DO NOT USE THE
ACCELERATOR PEDAL. IF THE ENGINE STARTS,
BE READY TO TURN OFF THE KEY PROMPTLY.
TAKE THESE PRECAUTIONS BECAUSE THE
VEHICLE COULD MOVE WITHOUT WARNING AND
POSSIBLY CAUSE PERSONAL INJURY OR
PROPERTY DAMAGE.
Starter Safety Switch Operation
Check by trying to start the engine in each gear while
setting the parking brake and the foot brake. The starter
should crank only in ªPº (Park) or ªNº (Neutral).
Accelerator Linkage Lubrication
Lubricate the accelerator pedal fulcrum pin with chassis
grease.
Steering and Suspension Inspection
Inspect the front and rear suspension and steering
system for damaged, loose or missing parts or signs of
wear. Inspect power steering lines and hoses for proper
hookup, binding, leaks, cracks, chafing, etc.
Body and Chassis Lubrication
Lubricate the key lock cylinders, the hood latch, the hood
and door hinges, the door check link, the parking cable
guides, the underbody contact points, and the linkage.
Propeller Shaft Inspection and Lubrication
Check the propeller shaft flange±to±pinion bolts for
proper torque to 63 Nwm (46 lb ft) for front and rear
propeller shaft.

2A±4
POWER±ASSISTED STEERING SYSTEM
Condition CorrectionPossible cause
Abnormal NoiseWorn, sticky or loose upper or lower
ball joint, steering linkage ball joints
or drive axle joints.Replace.
Faulty shock absorbers.Replace.
Worn upper or lower control arm
bushing.Replace.
Loose stabilizer bar.Retighten bolts or replace bushings.
Loose wheel nuts.Tighten nuts. Check for elongated
wheel nut holes.
Replace wheel if required.
Loose suspension bolts or nuts.Retighten suspension bolts or nuts.
Broken or otherwise damaged wheel
bearings.Replace wheel bearing.
Broken suspension springs. Replace spring.
Loose steering unit. Retighten mounting bolt.
Faulty steering unit.Replace steering unit.
Wandering or Poor Steering StabilityMismatched or unevenly worn tires.Replace tire or inflate tires to proper
pressure.
Loose steering linkage ball joints.Replace ball joints.
Faulty shock absorbers.Replace shock absorber.
Loose stabilizer bar.Tighten or replace stabilizer bar or
bushings.
Broken or sagging springs.Replace spring (pairs).
Improper wheel alignment.Adjust wheel alignment.
Erratic Steering When BrakingWorn wheel bearings.Replace wheel bearings.
Broken or sagging springs.Replace spring (pairs).
Leaking caliper.Repair or replace caliper.
Warped discs.Replace brake disc.
Badly worn brake pads.Replace brake pads.
Tires are inflated unequally.Inflate tires to proper pressure.

3C±4FRONT SUSPENSION
Condition CorrectionPossible cause
Abnormal NoiseWorn, sticky or loose upper or lower
ball joint, steering linkage ball joints
or drive axle joints.Replace.
Faulty shock absorbers.Replace.
Worn upper or lower control arm
bushing.Replace.
Loose stabilizer bar.Retighten bolts or replace bushings.
Loose wheel nuts.Tighten nuts. Check for elongated
wheel nut holes. Replace wheel if
required.
Loose suspension bolts or nuts.Retighten suspension bolts or nuts.
Broken or otherwise damaged wheel
bearings.Replace wheel bearing.
Broken suspension springs. Replace spring.
Loose steering unit. Retighten mounting bolt.
Faulty steering unit.Replace steering unit.
Wandering or Poor Steering StabilityMismatched or unevenly worn tires.Replace tire or inflate tires to proper
pressure.
Loose steering linkage ball joints.Replace ball joints.
Faulty shock absorbers.Replace shock absorber.
Loose stabilizer bar.Tighten or replace stabilizer bar or
bushings.
Broken or sagging springs.Replace spring (pairs).
Improper wheel alignment.Adjust wheel alignment.
Erratic Steering When BrakingWorn wheel bearings.Replace wheel bearings.
Broken or sagging springs.Replace spring (pairs).
Leaking caliper.Repair or replace caliper.
Warped discs.Replace brake disc.
Badly worn brake pads.Replace brake pads.
Tires are inflated unequally.Inflate tires to proper pressure.
Low or Uneven Trim HeightBroken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Incorrect springs.Adjust or replace torsion bar.
Suspension BottomsVehicle overloaded. Reduce load.
Faulty shock absorber.Replace shock absorber.
Incorrect, broken or sagging springs.Replace springs.
Body LeansLoose stabilizer bar.Tighten stabilizer bar bolts or replace
bushings.
Faulty shock absorber, struts or
mounting.Replace shock absorber.
Broken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Cupped TiresWorn wheel bearings.Replace wheel bearing.
Excessive tire or wheel run out.Replace tire or wheel.
Worn ball joints.Replace ball joints.
Tire out of balance.Adjust tire balance.

3D±4REAR SUSPENSION
Condition CorrectionPossible cause
Erratic Steering When BrakingWorn wheel bearings.Replace wheel bearings.
Broken or sagging springs.Replace spring (In pairs).
Leaking caliper.Repair or replace caliper.
Warped discs.Replace brake disc.
Badly worn brake pads.Replace brake pads.
Tires are inflated unequally.Inflate tires to proper pressure.
Low or Uneven Trim HeightBroken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Incorrect springs.Adjust or replace torsion bar.
Suspension BottomsVehicle overloaded. Reduce load.
Faulty shock absorber.Replace shock absorber.
Incorrect, broken or sagging springs.Replace springs.
Body LeansLoose stabilizer bar.Tighten stabilizer bar bolts or replace
bushings.
Faulty shock absorber, struts or
mounting.Replace shock absorber.
Broken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Cupped TiresWorn wheel bearings.Replace wheel bearing.
Excessive tire or wheel run out.Replace tire or wheel.
Worn ball joints.Replace ball joints.
Tire out of balance.Adjust tire balance.

3D±22REAR SUSPENSION
Condition CorrectionPossible cause
Erratic Steering When BrakingWorn wheel bearings.Replace wheel bearings.
Broken or sagging springs.Replace spring (pairs).
Leaking caliper.Repair or replace caliper.
Warped discs.Replace brake disc.
Badly worn brake pads.Replace brake pads.
Tires are inflated unequally.Inflate tires to proper pressure.
Low or Uneven Trim HeightBroken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Incorrect springs.Adjust or replace torsion bar.
Trim Height out of specAdjust Trim height
Suspension BottomsVehicle overloaded. Reduce load.
Faulty shock absorber.Replace shock absorber.
Incorrect, broken or sagging springs.Replace springs.
Body LeansTrim Height out of specAdjust Trim height
Loose stabilizer bar.Tighten stabilizer bar bolts or replace
bushings.
Faulty shock absorber, struts or
mounting.Replace shock absorber.
Broken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Cupped TiresWorn wheel bearings.Replace wheel bearing.
Excessive tire or wheel run out.Replace tire or wheel.
Worn ball joints.Replace ball joints.
Tire out of balance.Adjust tire balance.

WHEEL AND TIRE SYSTEM3E±5
Condition CorrectionPossible cause
Erratic Steering When BrakingWorn wheel bearings.Replace wheel bearings.
Broken or sagging springs.Replace spring (pairs).
Leaking caliper.Repair or replace caliper.
Warped discs.Replace brake disc.
Badly worn brake pads.Replace brake pads.
Tires are inflated unequally.Inflate tires to proper pressure.
Low or Uneven Trim HeightBroken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Incorrect springs.Adjust or replace torsion bar.
Suspension BottomsVehicle overloaded. Reduce load.
Faulty shock absorber.Replace shock absorber.
Incorrect, broken or sagging springs.Replace springs.
Body LeansLoose stabilizer bar.Tighten stabilizer bar bolts or replace
bushings.
Faulty shock absorber, struts or
mounting.Replace shock absorber.
Broken or sagging springs.Replace springs (In pairs).
Vehicle overloaded.Reduce load.
Cupped TiresWorn wheel bearings.Replace wheel bearing.
Excessive tire or wheel run out.Replace tire or wheel.
Worn ball joints.Replace ball joints.
Tire out of balance.Adjust tire balance.
Irregular and Premature Wear
480RS001
Irregular and/or premature wear has many causes.
Some of them are incorrect inflation pressures, lack of tire
rotation, poor driving habits or improper wheel alignment.
Incorrect inflation is common cause of tire premature
wear.NOTE: Due to their design, radial tires tend to wear faster
in the shoulder area, particularly on the front tires. This
makes regular rotation especially necessary. After
rotation, be sure to check wheel nut torque, and set tire
pressures.

4C±4
DRIVE SHAFT SYSTEM
7. Remove hub and disc assembly.
8. Remove ABS sensor ring.
9. Remove outer bearing.
10. Remove oil seal.
11. Remove inner bearing.
12. Use a brass bar to remove the outer bearing outer
race(1), oil seal, inner bearing and inner bearing outer
race(2) from the hub.
411RS002
13. Remove bolt.
14. If necessary, replace the wheel pin in the following
manner.

Scribe mark(1) on hub to disc before disassembly
to insure proper assembly.
411RS003

Clamp hub and disc assembly in vise, using
protective pads. Remove six(6) disc-to-hub
retaining bolts.
411RS021

Place hub on a suitable work surface and remove
wheel studs, as required, using a hammer.
411RS004
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal condition are
found through inspection.
Check the following parts.

Hub

Hub bearing oil seal

Knuckle spindle

Disc

Caliper

ABS sensor ring
For inspection and servicing of disc caliper and related
parts, refer to
Disc Brake in Brake section.

5C±1 POWER±ASSISTED BRAKE SYSTEM
AXIOM (Vehicles Produced Before July/31/2001)
BRAKES
POWER-ASSISTED BRAKE SYSTEM
CONTENTS
Service Precaution 5C±2. . . . . . . . . . . . . . . . . . . . . .
General Description 5C±2. . . . . . . . . . . . . . . . . . . . .
Diagnosis 5C±6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Diagnosis 5C±7. . . . . . . . . . . . . . . . . . . . . . .
Hydraulic Brakes 5C±10. . . . . . . . . . . . . . . . . . . . . . . .
Filling Master Cylinder Reservoir 5C±10. . . . . . . .
Deterioration of Brake Fluid 5C±10. . . . . . . . . . . . .
Leakage of Brake Fluid 5C±10. . . . . . . . . . . . . . . . .
Bleeding Brake Hydraulic System 5C±10. . . . . . . .
Flushing Brake Hydraulic System 5C±11. . . . . . . .
Brake Pipes and Hoses 5C±11. . . . . . . . . . . . . . . .
Brake Hose Inspection 5C±11. . . . . . . . . . . . . . . . .
Front Caliper Brake Hose 5C±12. . . . . . . . . . . . . . . .
Front Caliper Brake Hose and Associated
Parts 5C±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Axle Brake Hose 5C±13. . . . . . . . . . . . . . . . . . .
Rear Axle Brake Hose and Associated
Parts 5C±13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Pipe 5C±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
P & B (Proportioning and Bypass) Valve 5C±15. . . .
P & B (Proportioning and Bypass) Valve
Sectional View 5C±15. . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 5C±16. . . . . . . . . . . . .
Brake Pedal 5C±17. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Pedal Height 5C±17. . . . . . . . . . . . . . . . .
Checking Pedal Travel 5C±17. . . . . . . . . . . . . . . . .
Brake Pedal and Associated Parts 5C±18. . . . . . .
Removal 5C±18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±18. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stoplight Switch 5C±19. . . . . . . . . . . . . . . . . . . . . . . . .
Parts Location 5C±19. . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±19. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±19. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 5C±20. . . . . . . . . . . . .
Fluid Reservoir Tank 5C±21. . . . . . . . . . . . . . . . . . . . .
Fluid Reservoir Tank and Associated Parts 5C±21Removal 5C±21. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±21. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Master Cylinder Assembly 5C±22. . . . . . . . . . . . . . . .
Master Cylinder Assembly and Associated
Parts 5C±22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±22. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 5C±22. . . . . . . . . . . . . . . . . .
Installation 5C±23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 5C±24. . . . . . . . . . .
Special Tools 5C±24. . . . . . . . . . . . . . . . . . . . . . . . . .
Vacuum Booster Assembly 5C±25. . . . . . . . . . . . . . .
Vacuum Booster Assembly and Associated
Parts 5C±25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±25. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 5C±26. . . . . . . . . . . . . . . . . .
Installation 5C±26. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exterior Components 5C±28. . . . . . . . . . . . . . . . . . . .
Exterior Components and Associated Parts 5C±28
Removal 5C±28. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 5C±29. . . . . . . . . . . . . . . . . .
Installation 5C±29. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vacuum Booster Overhaul 5C±29. . . . . . . . . . . . . . . .
Vacuum Booster 5C±29. . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 5C±30. . . . . . . . . . . . .
Special Tools 5C±31. . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Disc Brake Pads 5C±32. . . . . . . . . . . . . . . . . . .
Front Disc Brake Pads Inspection 5C±32. . . . . . . .
Front Disc Brake Pads and Associated
Parts 5C±32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5C±33. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±33. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Disc Brake Rotor 5C±35. . . . . . . . . . . . . . . . . . .
Inspection 5C±35. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing Brake Rotors 5C±35. . . . . . . . . . . . . . . .
Refinishing Brake Rotors 5C±35. . . . . . . . . . . . . . .
Front Disc Brake Caliper Assembly 5C±36. . . . . . . .
Front Disc Brake Caliper Assembly and
Associated Parts 5C±36. . . . . . . . . . . . . . . . . . . . . .
Removal 5C±37. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5C±37. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Disc Brake Caliper 5C±39. . . . . . . . . . . . . . . . .
Front Disc Brake Caliper Disassembled
View 5C±39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly 5C±39. . . . . . . . . . . . . . . . . . . . . . . . . .