key ISUZU AXIOM 2002 Service Repair Manual

0B±6MAINTENANCE AND LUBRICATION
Always change the oil and the oil filter as soon as possible
after driving in a dust storm.
Engine Cooling System Inspection
Inspect the coolant/anti±freeze. If the coolant is dirty or
rusty, drain, flush and refill with new coolant. Keep coolant
at the proper mixture for proper freeze protection,
corrosion inhibitor level and best engine operating
temperature. Inspect hoses and replace if cracked,
swollen or deteriorated. Tighten the hose clamps if
equipped with screw±type clamps. Clean outside of
radiator and air conditioning condenser. Wash filler cap
and neck. To help ensure proper operation, a pressure
test of both the cooling system and the cap is also
recommended.
Exhaust System Inspection
Visually inspect the exhaust pipes, muffler, heat shields
and hangers for cracks, deterioration, or damage.
Be alert to any changes in the sound of the exhaust
system or any smell of fumes. These are signs the system
may be leaking or overheating. Repair the system at
once, if these conditions exist. (See also ªEngine Exhaust
Gas Safetyº and ªThree Way Catalytic Converterº in the
Owner's manual.)
Fuel Cap, Fuel Lines, and Fuel Tank
Inspection
Inspect the fuel tank, the fuel cap and the fuel lines every
60,000 miles (96,000 km) for damage which could cause
leakage.
Inspect the fuel cap and the gasket for correct sealing and
physical damage. Replace any damaged parts.
Drive Belt Inspection
Check the serpentine belt driving for cracks, fraying,
wear, and correct tension every 30,000 miles (48,000
km). Replace as necessary.
Wheel Alignment, Balance and Tires
Operation
Uneven or abnormal tire wear, or a pull right or left on a
straight and level road may show the need for a wheel
alignment. A vibration of the steering wheel or seat at
normal highway speeds means a wheel balancing is
needed. Check tire pressure when the tires are ªcoldº
(include the spare).
Maintain pressure as shown in the tire placard, which is
located on the driver's door lock pillar.
Steering System Operation
Be alert for any changes in steering operation. An
inspection or service is needed when the steering wheel
is harder to turn or has too much free play, or if there are
unusual sounds when turning or parking.
Brake Systems Operation
Watch for the ªBRAKEº light coming on. Other signs of
possible brake trouble are such things as repeated pulling
to one side when braking, unusual sounds when braking
or between brake applications, or increased brake pedaltravel. If you note one of these conditions, repair the
system at once.
For convenience, the following should be done when
wheels are removed for rotation: Inspect lines and hoses
for proper hookup, bindings, leaks, crack, chafing etc.
Inspect disc brake pads for wear and rotors for surface
condition.
Inspect other brake parts, including parking brake drums,
linings etc., at the same time. Check parking brake
adjustment.
Inspect the brakes more often if habit or conditions
result in frequent braking.
Parking Brake and Transmission Park
Mechanism Operation
Park on a fairly steep hill and hold the vehicle with the
parking brake only. This checks holding ability. On
automatic transmission vehicles, shifting from ªPº
position to the other positions cannot be made unless the
brake pedal is depressed when the key switch is in the
ªONº position or the engine is running.
WARNING: B E F O R E C H E C K I N G T H E S TA R T E R
SAFETY SWITCH OPERATION BELOW, BE SURE TO
HAVE ENOUGH ROOM AROUND THE VEHICLE.
THEN FIRMLY APPLY BOTH THE PARKING BRAKE
AND THE REGULAR BRAKE. DO NOT USE THE
ACCELERATOR PEDAL. IF THE ENGINE STARTS,
BE READY TO TURN OFF THE KEY PROMPTLY.
TAKE THESE PRECAUTIONS BECAUSE THE
VEHICLE COULD MOVE WITHOUT WARNING AND
POSSIBLY CAUSE PERSONAL INJURY OR
PROPERTY DAMAGE.
Starter Safety Switch Operation
Check by trying to start the engine in each gear while
setting the parking brake and the foot brake. The starter
should crank only in ªPº (Park) or ªNº (Neutral).
Accelerator Linkage Lubrication
Lubricate the accelerator pedal fulcrum pin with chassis
grease.
Steering and Suspension Inspection
Inspect the front and rear suspension and steering
system for damaged, loose or missing parts or signs of
wear. Inspect power steering lines and hoses for proper
hookup, binding, leaks, cracks, chafing, etc.
Body and Chassis Lubrication
Lubricate the key lock cylinders, the hood latch, the hood
and door hinges, the door check link, the parking cable
guides, the underbody contact points, and the linkage.
Propeller Shaft Inspection and Lubrication
Check the propeller shaft flange±to±pinion bolts for
proper torque to 63 Nwm (46 lb ft) for front and rear
propeller shaft.

0B±8MAINTENANCE AND LUBRICATION
Recommended Fluids and Lubricants
USAGEFLUID/LUBRICANT
EngineAPI SE, SF, SG, SH or ILSAC GF-1 Engine oil (See oil
chart on the following page for proper viscosity)
Engine coolantMixture of water and good quality ethylene glycol base
type antifreeze.
Brake systemDOT-3 hydraulic brake fluid.
Power steering systemDEXRON) -III Automatic transmission fluid.
Automatic transmissionDEXRON) -III Automatic transmission fluid.
TOD SYSTEM (TOD system model only)DEXRON) -IIE or DEXRON) -III Automatic transmis-
sion fluid.
Rear axle and front axleGL-5 gear lubricant (Standard differential)
GL-5 Limited slip differential gear lubricant together
with limited slip differential lubricant additive (Part No.
8-01052-358-0) or equivalent (If equipped with optional
limited slip differential) (See oil chart in this section for
proper viscosity)
Hood latch assembly
a. Pivots and spring anchorEngine oil
b. Release pawlChassis grease
Hood and door hingesEngine oil
Chassis lubricationChassis grease
Parking brake cablesChassis grease
Front wheel bearingsMultipurpose grease
Shift on the fly systemGL-5 gear lubricant (SAE 75W-90)
Body door hinge pins and linkage, fuel door hinge, rear
compartment lid hingesEngine oil
Windshield washer solventWasher fluid
Key lock cylinderSynthetic light weight engine oil (SAE 5W-30)
Accelerator linkageChassis grease

1A±92
HEATING, VENTILATION AND AIR CONDITIONING (HVAC)
StepActionValue(s)Ye sNo
11. Allow the engine to idle until it completely warms up.
2. Turn the starter switch to the OFF position.
3. Place a 60±watt lamp approximately 15 cm from the
sun sensor.
NOTE: This procedure is best performed at night or in
a dark, unlit area.
Is the action complete?
ÐGo to Step 2Ð
2Simultaneously press and hold the RESET key and the
CLOCK key (display unit).
Move the starter switch to start the engine.
Does DIAG appear on the display?
ÐGo to Step 3
Replace
display unit
3Press the COMPUTER MODE key.
Does DIAG AIRCON appear on the display?
ÐGo to Step 4
Replace
audio unit
4NOTE: A '1' should appear in the set temperature
segment of the display.
Does '0' appear in the outside air segment of the
display?
ÐGo to Step 6Go to Step 5
5Repair or replace damaged parts.
NOTE: Refer to
Step 1 Trouble Code Table.
Is the action complete?ÐGo to Step 1Ð
6Press and release the  fan switch (one time only).
NOTE: A '2' should appear in the set temperature
segment of the display.
Does '0' appear in the outside air segment of the
display?
ÐGo to Step 8Go to Step 7
7Repair or replace damaged parts.
NOTE: Refer to
Step 2 Trouble Code Table.
Is the action complete?ÐGo to Step 1Ð
8Press and release the  fan switch (one time only).
NOTE:

Refer to
Step 3 Sensor Output Check for a sample
output value.

A '3' should appear in the set temperature
segment of the display.
Does the correct sensor output value appear in the
outside air segment of the display?
ÐGo to Step 10Go to Step 9
9Repair or replace damaged parts.
NOTE: Refer to
Trouble Spot Inspection.
Is the action complete?ÐGo to Step 1Ð
10Press and release the  fan switch one time only.
NOTE: Refer to
Step 4 (Operation Check) for display
readings and inspection steps.
Are all parts operating normally?
ÐGo to Step 12Go to Step 11

2A±6
POWER±ASSISTED STEERING SYSTEM
Power Steering Pump
Foaming milky power steering fluid, low fluid level, and
possible low pressure can be caused by air in the fluid, or
loss of fluid due to internal pump leakage. Check for leak
and correct. Bleed the system. Extremely cold
temperatures will cause air bubbles in the system if thefluid level is low. If the fluid level is correct and the pump
still foams, remove the pump from the vehicle and check
housing for cracks. If the housing is cracked, replace the
pump housing.
Condition
Possible causeCorrection
Low Pressure Due to Steering PumpRelief valve sticking or inoperative.Replace relief valve.
Side plate not flat against cam ring.Replace side plate.
Extreme wear of cam ring.Replace cam ring.
Scored side plate or rotor.Replace side plate or rotor.
Vanes sticking in rotor slots.Repair or replace vanes and rotor.
Cracked or broken side plate.Replace side plate.
High internal leakage.Repair internal leakage.
Low Pressure Due to Steering GearScored housing bore.Replace housing.
Growling Noise In Steering PumpExcessive back pressure in hoses or
steering unit caused by restriction.Repair steering unit or pump.
Scored side plate or rotor.Replace side plate or rotor.
Worn cam ring.Replace cam ring.
Groaning Noise In Steering PumpAir in the fluid.Bleed hydraulic system.
Low fluid level.Replenish fluid.
Pump mounting loose.Tighten mounting bolt.
Rattling Noise In Steering PumpVanes sticking in rotor slots.Repair or replace vanes and rotor.
Vane improperly installed.Repair rotor and vane.
Swishing Noise In Steering PumpDamaged relief valve.Replace relief valve.
Whining Noise In Steering PumpScored side plate and vanes.Replace side plate and vanes.
Steering Column Lock System
ConditionPossible causeCorrection
Will Not UnlockDamaged lock cylinder.Replace lock cylinder.
Damaged park lock cable.Replace park lock cable.
Will Not LockLock spring broken or worn.Replace lock cylinder.
Damaged lock cylinder.Replace lock cylinder.
Ignition switch stuck.Repair or replace ignition switch.
Park lock cable damaged.Replace park lock cable.
Key Cannot be Removed in
ªOFF LOCKº
Ignition switch is not set correctly.Correct ignition switch.
ªOFF-LOCKºDamaged lock cylinder.Replace lock cylinder.
Faulty shift lock mechanism.Repair or replace the shift lock
mechanism.
Column
ConditionPossible causeCorrection
Noise in ColumnUniversal joint loose.Tighten joint.
Shaft lock snap ring not seated.Place snap ring in proper position.

3F±6INTELLIGENT SUSPENSION
FLASHING CODES
1. ON BOARD DIAGNOSIS (SELF-DIAGNOSIS)
1. The Control Unit conducts a self-test of most of the
wiring and components in the system each time the
key is turned ON. If a fault is detected the Control
Unit will store a Diagnostic Trouble Code (DTC) in
memory. It's a number that corresponds to a
specific problem.
2. When the problem detected is important: the
warning lamp turns on until the fault is repaired and
the Control Unit memory is cleared.
2. DIAGNOSTIC TROUBLE CODES (DTC)
1. DTC can be expressed by flashing times of warning
lamp by shorting together terminals 3 and 4 or 5 of
the Diagnosis Connector (C-39) located left side of
instrument panel.
350R200002
Normal
F03RY00001
Abnormal
F03R200001
Legend
(1) Diagnostic Trouble Code 2
(2) Diagnostic Trouble Code 3

4B1±4
DRIVELINE CONTROL SYSTEM
Functions of Indicator Lamp
TOD Switch and Indication of Drive Mode
The TOD switch sends signals to the TOD control unit
which selects drive modes and controls the shift on the fly
system (axle disconnect : ADC).
TOD
switch
tt
Drive modeTransfer shift conditionTransfer posi-
tion detectionShift on the flyTOD indicator
state
state4HSW4LSWAxle
SWADC circuit
2HRear-wheel
drive (RWD)Permissible during
driving (less than
100 km/h or 62 mph)OFFOFFOFFTurning on
electricity
TODElectronic
torque split
4WD (HIGH)
OFFOFFONTurning off
electricity
4WD (HIGH)
(TOD)AT: Neutral
Brake: Applied
Th t (l4LLow range
mechanical
direct 4WD
(LOW) (4L)The car stops (less
than 2 km/h or
1.2 mph and less than
1500 rpm)OFFONONTurning off
electricity
ADC: Shift on the fly
SW: Switch
Bulb check :The bulb of indicator lamp is checked for 2
seconds when ignition key is turned on.
Bulb Check
When the starter switch is turned on, the TOD indicator
lamps comes on as shown below.
NOTE: Once the starter switch is turned on, all the TOD
indicator lamps are lit for two seconds even if the transfer
lever is in any position.
C07RW016

5A±1
BRAKE CONTROL SYSTEM
AXIOM
BRAKES
CONTENTS
Brake Control System 5A±1. . . . . . . . . . . . . . . . . . . .
Anti±lock Brake System 5B±1. . . . . . . . . . . . . . . . . .
Power±assisted Brake System 5C±1. . . . . . . . . . . .
Parking Brakes (4x4 Model) 5D1±1. . . . . . . . . . . . . .
Parking Brakes (4x2 Model) 5D2±1. . . . . . . . . . . . . .
Brake Control System
CONTENTS
Service Precaution 5A±2. . . . . . . . . . . . . . . . . . . . . .
General Description 5A±3. . . . . . . . . . . . . . . . . . . . .
Functional Description 5A±4. . . . . . . . . . . . . . . . .
System Components 5A±10. . . . . . . . . . . . . . . . . . .
Electronic Hydraulic Control Unit (EHCU) 5A±10.
ABS Warning Light 5A±10. . . . . . . . . . . . . . . . . . . .
Wheel Speed Sensor 5A±10. . . . . . . . . . . . . . . . . .
G-Sensor 5A±10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Normal and Anti-lock Braking 5A±10. . . . . . . . . . .
Brake Pedal Travel 5A±10. . . . . . . . . . . . . . . . . . . .
Acronyms and Abbreviations 5A±11. . . . . . . . . . . .
General Diagnosis 5A±11. . . . . . . . . . . . . . . . . . . . . . .
General Information 5A±11. . . . . . . . . . . . . . . . . . . .
ABS Service Precautions 5A±11. . . . . . . . . . . . . . .
Computer System Service Precautions 5A±11. . .
General Service Precautions 5A±11. . . . . . . . . . . .
Note on Intermittents 5A±11. . . . . . . . . . . . . . . . . . .
Test Driving ABS Complaint Vehicles 5A±12. . . . .
ªABSº Warning Light 5A±12. . . . . . . . . . . . . . . . . . .
Normal Operation 5A±12. . . . . . . . . . . . . . . . . . . . .
Tech 2 Scan Tool 5A±13. . . . . . . . . . . . . . . . . . . . . .
DATA LIST 5A±16. . . . . . . . . . . . . . . . . . . . . . . . . . .
ACTUATOR TEST 5A±17. . . . . . . . . . . . . . . . . . . . .
Tech 2 Service Bleed 5A±21. . . . . . . . . . . . . . . . . .
Basic Diagnostic Flow Chart 5A±22. . . . . . . . . . . .
Basic Inspection Procedure 5A±23. . . . . . . . . . . . .
EHCU Connector Pin-out Checks 5A±24. . . . . . . . .
Circuit Diagram 5A±25. . . . . . . . . . . . . . . . . . . . . . .
Connector List 5A±28. . . . . . . . . . . . . . . . . . . . . . . .
Part Location 5A±29. . . . . . . . . . . . . . . . . . . . . . . . .
Symptom Diagnosis 5A±30. . . . . . . . . . . . . . . . . . . . .
Chart A-1 ABS Works Frequently But
Vehicle Does Not Decelerate 5A±30. . . . . . . . . . .
Chart TA-1 ABS Works Frequently But
Vehicle Does Not Decelerate
(Use TECH 2) 5A±31. . . . . . . . . . . . . . . . . . . . . . . .
Chart A-2 Uneven Braking Occurs While
ABS Works 5A±31. . . . . . . . . . . . . . . . . . . . . . . . . . .
Chart TA-2 Uneven Braking Occurs While
ABS Works (Use TECH 2) 5A±31. . . . . . . . . . . . . Chart A-3, TA-3 The Wheels Are Locked 5A±32.
Chart A-4 Brake Pedal Feed Is Abnormal 5A±32.
Chart A-5, TA-5 Braking Sound
(From EHCU) Is Heard While Not Braking 5A±33
Diagnostic Trouble Codes 5A±34. . . . . . . . . . . . . . . .
Diagnosis By ªABSº Warning Light
Illumination Pattern 5A±36. . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes (DTCs) 5A±37. . . . . . .
Chart B-1 With the key in the ON position
(Before starting the engine). Warning light
(W/L) is not activated. 5A±39. . . . . . . . . . . . . . . . .
Chart B-2 CPU Error (DTC 14 (Flash out) /
C0271, C0272, C0273, C0284 (Serial
communications)) 5A±39. . . . . . . . . . . . . . . . . . . . .
Chart B-3 Low or High Ignition Voltage
(DTC 15 (Flash out) / C0277, 0278 (Serial
communications)) 5A±40. . . . . . . . . . . . . . . . . . . . .
Chart B-4 Excessive Dump Time (DTC 17
(Flash out) / C0269 (Serial
communications)) 5A±40. . . . . . . . . . . . . . . . . . . . .
Chart B-5 Excessive Isolation Time
(DTC 18 (Flash out) / C0274
(Serial communications)) 5A±40. . . . . . . . . . . . . . .
Chart B-6 G-Sensor Output Failure
(DTC 21 (Flash out) / C0276
(Serial communications)) 5A±41. . . . . . . . . . . . . . .
Chart B-7 Brake Switch Failure
(DTC 22 (Flash out) / C0281
(Serial communications)) 5A±41. . . . . . . . . . . . . . .
Chart B-8 2WD Controller in 4WD Vehicle
Controller (DTC 13 (Flash out) / C0285
(Serial communications)), 4WD State Input
Signal Failure (DTC 24 (Flash out) / C0282
(Serial communications)) 5A±42. . . . . . . . . . . . . . .
Chart B-9 Pump Motor Failure
(DTC 32 (Flash out) / C0267, C0268
(Serial communications)) 5A±42. . . . . . . . . . . . . . .
Chart B-10 EHCU Valve Relay Failure
(DTC 35 (Flash out) / C0265, C0266
(Serial communications)) 5A±43. . . . . . . . . . . . . . .
Chart B-11 FL Isolation Solenoid Coil Failure
(DTC 41 (Flash out) / C0245, C0247
(Serial communications)) 5A±43. . . . . . . . . . . . . . .
Chart B-12 FL Dump Solenoid Coil Failure
(DTC 42 (Flash out) / C0246, C0248
(Serial communications)) 5A±43. . . . . . . . . . . . . . .

5A±36BRAKE CONTROL SYSTEM
Diagnosis By ªABSº Warning Light
Illumination Pattern
In the event that there is abnormality in the ªABSº warning
light illumination pattern while the key is in the ON position
or if the warning light is actuated while driving, refer to the
flow chart below for the correct diagnostic procedure.
No.
ConditionªABSº Warning Light Illumination PatternDiagnostic
1Warning light is
actuated normallyNormal
2Warning light is not litWarning light lighting circuit
trouble"Go to Chart B-1
3Warning light remains
ONDiagnostic trouble codes are
stored.
Display diagnostic trouble
codes and diagnose on a
code basis according to the
flow charts.
4Warning light is
actuated while drivingDiagnostic trouble codes are
stored.
Display diagnostic trouble
codes and diagnose on a
code basis according to the
flow charts.
5Warning light goes at
12 km/h (8 mph) or
higher (After repairing
the faulty part)Even after repairing the
faulty part the warning light
(W/L) dose not go out if
vehicle is at a stop.
Turn the ignition switch to the
ON position and drive the
vehicle at 12 km/h (8 mph) or
higher to make sure that the
warning light goes out.

5A±38BRAKE CONTROL SYSTEM
4. Notes

If the following should occur during Diagnostic
Trouble Code (DTC) display, the display will be
discontinued. After initial check, the status that is
under the control of ABS will be returned :
± The vehicle starts (The wheels turn) or the brake
pedal is depressed.

Up to 3 different codes can be stored.

If the ABS should turn OFF due to an intermittent
defect, the system will be restored at the next key
cycle, if the initial check finds no abnormality (when
IGN is switched from OFF to ON).
5. An example of DTC display
B05R100001
After displaying DTC 12 three times, one DTC after
another is displayed, starting with the most recent
one. (However, display is discontinued after about 5
minutes.)
B05R100002
The DTC 12 is displayed repeatedly. (display is
discontinued after about 5 minutes after)

5A±39
BRAKE CONTROL SYSTEM
Chart B-1 With the key in the ON position (Before starting the engine). Warning light (W/L)
is not activated.
StepActionYe sNo
1Is W/L fuse disconnected?Replace fuse.
Go to
Step 5Go to Step 2
2Is W/L burnt out?Replace W/L
bulb.
Go to
Step 5Go to Step 3
31. Turn the key off.
2. Disconnect coil integrated module connector (C-6).
3. Turn the key ON.
Is the check voltage between coil integrated module connector
(C-6) terminals 6 and 7 the battery voltage?
Go to Step 4
Repair harness
and connector.
Go to
Step 5
4Is there the continuity between coil integrated module connector
(C-6) terminals, 1 and 7 and body ground.Check harness
for suspected
disconnection
No fault found:
Replace EHCU.
Go to
Step 5
Repair harness
and connector.
Go to
Step 5
5Reconnect all components, ensure all components are properly
mounted.
Was this step finished?Repeat the ªBasic
diagnostic flow
chartº
Go to Step 5
Chart B-2 CPU Error (DTC 14 (Flash out) / C0271, C0272, C0273, C0284 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnected coil integrated module connector.
3. Inspect coil integrated module ground.
Is there the continuity between the coil integrated module
connector terminals, 2 (C-5) and 7 (C-6) and body ground?
Go to Step 2
Repair the body
ground harness.
Go to
Step 3
21. Turn the key off, connect the coil integrated module connector.
2. Erase the trouble code.
3. Turn Ignition off, then on, to perform system self-check.
4. If warning light remains on, display trouble codes once again.
Is the trouble code the DTC 14 (Flash out) / C0271, C0272,
C0273, C0284 (Serial communications)?
Replace EHCU.
Go to
Step 3
Inspect in
accordance with
the DTC
displayed.
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3