power steering fluid ISUZU AXIOM 2002 Service Repair Manual

0B±1 MAINTENANCE AND LUBRICATION
AXIOM
GENERAL INFORMATION
Maintenance and Lubrication
CONTENTS
Maintenance Schedule List 0B±1. . . . . . . . . . . . . . .
Explanation of Complete Vehicle Maintenance
Schedule 0B±5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Fluids and Lubricants 0B±8. . . .
Lubricant Viscosity Chart 0B±9. . . . . . . . . . . . . . . . . Recommended Liquid Gasket 0B±11. . . . . . . . . . .
Recommended Thread Locking Agents 0B±11. . .
Maintenance Service Data 0B±12. . . . . . . . . . . . . . . .
Maintenance Schedule List
Normal Vehicle Use
The maintenance instructions in this Maintenance
Schedule are based on the assumption that the vehicle
will be used as designed:

to carry passengers and cargo within the limitations
specified on the tire placard located on the inside of
the glove compartment door;

to be driven on reasonable road surfaces within legal
operating limits;

to be driven on a daily basis, as a general rule, for at
least several miles/kilometers;

to be driven on unleaded fuel
Unusual or severe operating conditions will require more
frequent vehicle maintenance, as specified in the
following sections.
Severe Driving Conditions
If the vehicle is usually operated under any of the severe
driving conditions listed below, it is recommended that the
applicable maintenance services be performed at the
specified interval shown in the chart below.
Severe driving conditions:

Towing a trailer, using a camper or car top carrier.

Repeated short trips of less than 8 Km (5 miles) with
outside temperature remaining below freezing.

Extensive idling and/or low speed driving for long
distances, such as police, taxi or door±to±door
delivery use.

Operating on dusty, rough, muddy or salt spread
roads.
ITEMS
INTERVAL
CHANGE ENGINE OIL AND OIL FILTEREvery 3,000 miles (4,800 km) or 3 months
CHANGE AUTOMATIC TRANSMISSION FLUIDEvery 20,000 miles (32,000 km)
CHANGE REAR AXLE OILEvery 15,000 miles (24,000 km)
REPLACE TIMING BELTEvery 75,000 miles (120,000 km)
REPLACE AIR CLEANER FILTERSee explanation of service, page 0B±5
CHANGE POWER STEERING FLUIDEvery 30,000 miles (48,000 km)

0B±5 MAINTENANCE AND LUBRICATION
Explanation of Complete Vehicle
Maintenance Schedule
Brief explanations of the services listed in the preceding
Maintenance Schedule are presented below.
Replace all questionable parts and note any necessary
repairs as you perform these maintenance procedures.
Front and Rear Axle Lubricant
Replacement
Check the lubricant level after every 7,500 miles (12,000
km) of operation and add lubricant to level of filler hole if
necessary.
Replace the front and rear axle lubricant at 15,000 miles
(24,000 km) and 30,000 miles (48,000 km) and after
every 30,000 miles (48,000 km) of operation thereafter.
Air Cleaner Element Replacement
Replace the air cleaner under normal operating
conditions every 30,000 miles (48,000 km).
Operation of the vehicle in dusty areas will necessitate
more frequent replacement.
Spark Plug Replacement
Replace the plugs at 100,000 miles (160,000 km)
intervals with the type specified at the end of this section.
Cooling System Service
Drain, flush and refill system with new engine coolant.
Refer to
ªRecommended Fluids and Lubricantsº in this
section, or ENGINE COOLING (SEC.6B).
Timing Belt Replacement
Replacement of the timing belt is recommended at every
100,000 miles (160,000 km).
Failure to replace the timing belt may result in serious
damage to the engine.
Valve Clearance Adjustment
Incorrect valve clearance will result in increased engine
noise and reduced engine output.
Retorque the camshaft bracket bolts before checking and
adjusting the valve clearance.
Check and adjust the valve clearance whenever
increased engine noise is heard.
Tire Rotation
Rotate tires every 7,500 miles (12,000 km).
Front Wheel Bearings Lubricant
Replacement (Vehicles Produced Before
July/31/2001)
Clean and repack the front wheel bearings at 30,000
miles (48,000 km) intervals.
Refer to DRIVE SHAFT SYSTEM (SEC. 4C).
Front Wheel Bearings Check (Vehicles
Produced After Aug./1/2001)
Inspect hub unit bearing at every 60,000 miles (96,000
km).
If there is abnormal condition, replace hub unit bearing.
Radiator Core and Air Conditioning
Condenser Cleaning
Clean the front of the radiator core and air conditioning
condenser, at 60,000 miles (96,000 km) intervals.
Fluid Level Check
A fluid loss in any system (except windshield
washer) may indicate a problem. Repair the system
at once.
Engine oil level
Check level and add if necessary. The best time to check
the engine oil level is when the oil is warm. After stopping
the engine with the vehicle on a level surface, wait a few
minutes for the oil to drain back to the oil pan. Pull out the
oil level indicator (dipstick). Wipe it clean and push the oil
level indicator back down all the way. Pull out the oil level
indicator, keeping the tip down, and look at the oil level on
it.
Add oil, if needed, to keep the oil level above the ªADDº
mark and between the ªADDº and ªFULLº marks in the
operating range area. Avoid overfilling the engine since
this may cause engine damage. Push the oil level
indicator back down all the way after taking the reading.
If you check the oil level when the oil is cold, do not run the
engine first. The cold oil will not drain back to the pan fast
enough to give a true oil level.
Engine coolant level and condition
Check engine coolant level in the coolant reservoir and
add engine coolant if necessary. Inspect the engine
coolant and replace it if dirty or rusty.
Windshield washer fluid level
Check washer fluid level in the reservoir and add if
necessary.
Power steering system reservoir level
Check and keep at the proper level.
Brake master cylinder reservoir level
Check fluid. Keep fluid at proper level. A low fluid level can
indicate worn disc brake pads which may need to be
serviced.
Hydraulic clutch system
Check fluid level in the reservoir. Add fluid as required.
Battery fluid level
Check fluid level in the battery.
Fluid Leak Check
Check for fuel, water, oil or other fluid leaks by looking at
the surface beneath the vehicle after it has been parked
for a while. Water dripping from the air conditioning
system after use is normal. If you notice gasoline fumes or
fluid at any time, locate the source and correct it at once.
Engine Oil and Oil Filter Replacement
Always use API SE, SF, SG, SH or ILSAC GF±1 quality
oils of the proper viscosity.
When choosing an oil, consider the range of
temperatures the car will be operated in before the next oil
change. Then, select the recommended oil viscosity from
the chart.

0B±8MAINTENANCE AND LUBRICATION
Recommended Fluids and Lubricants
USAGEFLUID/LUBRICANT
EngineAPI SE, SF, SG, SH or ILSAC GF-1 Engine oil (See oil
chart on the following page for proper viscosity)
Engine coolantMixture of water and good quality ethylene glycol base
type antifreeze.
Brake systemDOT-3 hydraulic brake fluid.
Power steering systemDEXRON) -III Automatic transmission fluid.
Automatic transmissionDEXRON) -III Automatic transmission fluid.
TOD SYSTEM (TOD system model only)DEXRON) -IIE or DEXRON) -III Automatic transmis-
sion fluid.
Rear axle and front axleGL-5 gear lubricant (Standard differential)
GL-5 Limited slip differential gear lubricant together
with limited slip differential lubricant additive (Part No.
8-01052-358-0) or equivalent (If equipped with optional
limited slip differential) (See oil chart in this section for
proper viscosity)
Hood latch assembly
a. Pivots and spring anchorEngine oil
b. Release pawlChassis grease
Hood and door hingesEngine oil
Chassis lubricationChassis grease
Parking brake cablesChassis grease
Front wheel bearingsMultipurpose grease
Shift on the fly systemGL-5 gear lubricant (SAE 75W-90)
Body door hinge pins and linkage, fuel door hinge, rear
compartment lid hingesEngine oil
Windshield washer solventWasher fluid
Key lock cylinderSynthetic light weight engine oil (SAE 5W-30)
Accelerator linkageChassis grease

POWER±ASSISTED STEERING SYSTEM2A±1
AXIOM
STEERING
POWER-ASSISTED STEERING SYSTEM
CONTENTS
Service Precaution 2A±2. . . . . . . . . . . . . . . . . . . . . .
Diagnosis 2A±2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Description 2A±8. . . . . . . . . . . . . . . . . . . . .
Power Steering System Test 2A±10. . . . . . . . . . . . . .
Maintenance 2A±11. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fluid Level 2A±11. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bleeding The Power Steering System 2A±11. . . . . .
Bleeding Procedure 2A±11. . . . . . . . . . . . . . . . . . . . .
Flushing The Power Steering System 2A±11. . . . . .
Steering Wheel Free Play Inspection 2A±12. . . . . .
Front End Alignment Inspection and
Adjustment 2A±12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 2A±16. . . . . . . . . . . . .
Special Tools 2A±17. . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Unit 2A±18. . . . . . . . . . . . . . . . . . . . .
Power Steering Unit and Associated Parts 2A±18
Removal 2A±18. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation (4y2 Model) 2A±19. . . . . . . . . . . . . . . .
Installation (4y4 Model) 2A±19. . . . . . . . . . . . . . . .
Power Steering Unit Disassembled View 2A±20. .
Disassembly 2A±21. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 2A±21. . . . . . . . . . . . . . . . . .
Reassembly 2A±21. . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 2A±22. . . . . . . . . . .
Special Tools 2A±22. . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Pump 2A±23. . . . . . . . . . . . . . . . . . . .
Power Steering Pump and Associated Parts 2A±23
Removal 2A±23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 2A±23. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Steering Pump Disassembled View 2A±24
Disassembly 2A±24. . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 2A±25. . . . . . . . . . . . . . . . . .
Reassembly 2A±25. . . . . . . . . . . . . . . . . . . . . . . . . .
Main Data and Specifications 2A±27. . . . . . . . . . .
Transfer Gear Assembly 2A±28. . . . . . . . . . . . . . . . .
Transfer Gear Assembly and Associated
Parts 2A±28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removal 2A±28. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 2A±28. . . . . . . . . . . . . . . . . .
Installation 2A±28. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental Restraint System Steering
Wheel & Column 2A±29. . . . . . . . . . . . . . . . . . . . . . .
Service Precaution 2A±29. . . . . . . . . . . . . . . . . . . .
SRS Connectors 2A±29. . . . . . . . . . . . . . . . . . . . . .
Inflator Module 2A±31. . . . . . . . . . . . . . . . . . . . . . . . . .
Inflator Module and Associated Parts 2A±31. . . . .
Removal 2A±31. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 2A±32. . . . . . . . . . . . . . . . . .
Installation 2A±32. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering Wheel 2A±33. . . . . . . . . . . . . . . . . . . . . . . . .
Steering Wheel and Associated Parts 2A±33. . . .
Removal 2A±33. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 2A±35. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Combination Switch 2A±36. . . . . . . . . . . . . . . . . . . . .
Combination Switch and Associated Parts 2A±36
Removal 2A±36. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 2A±38. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Cylinder 2A±40. . . . . . . . . . . . . . . . . . . . . . . . . . .
Lock Cylinder and Associated Parts 2A±40. . . . . .
Removal 2A±40. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 2A±42. . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Inspection 2A±43. . . . . . . . . . . . . . . . . . . . .
Steering Column 2A±44. . . . . . . . . . . . . . . . . . . . . . . .
Steering Column and Associated Parts 2A±44. . .
Removal 2A±44. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection 2A±46. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 2A±48. . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Inspection 2A±49. . . . . . . . . . . . . . . . . . . . .
Supplemental Restraint System Steering
Wheel & Column and Associated Parts 2A±50. . . .
Main Data and Specifications 2A±50. . . . . . . . . . .
Special Tools 2A±50. . . . . . . . . . . . . . . . . . . . . . . . . .

POWER±ASSISTED STEERING SYSTEM2A±5
Power Steering System
There is some noise in all power steering systems. One
of the most common is a hissing sound when the steering
wheel is fully turned and the car is not moving. This noise
will be most evident when the steering wheel is operated
while the brakes are applied. There is no relationshipbetween this noise and steering performance. Do not
replace the valve unless the ªhissingº noise is extremely
objectionable. A replacement valve will also have a slight
noise, and is not always a cure for the condition.
Condition
Possible causeCorrection
Rattle or Chucking NoisePressure hose touching other parts
of vehicle.Adjust hose position. Do not bend
tubing by hand.
Tie rod ends loose.Tighten or replace tie rod end.
Loose steering unit mounting.Tighten steering unit mounting.
Poor Return of Steering Wheel to
Center
Improper front wheel alignment.Adjust front wheel alignment.
CenterWheel bearing worn.Replace front wheel bearing.
Tie rod end binding.Replace tie rod end.
Ball joint binding.Replace ball joint.
Tight or frozen steering shaft
bearing.Replace steering assembly.
Sticky or plugged steering unit valve.Flush or replace steering unit.
Entry of air in the power steering
system.Bleed the system.
Momentary Increase In Effort When
Turning Wheel Fast To Right or Left
High internal leakage.Repair steering gear.
Turning Wheel Fast To Right or LeftPower steering fluid level low.Replenish fluid.
Steering Wheel Surges or Jerks
When Turning Especially During
Insufficient pump pressure.Repair pump assembly.
When Turning Especially During
Parkin
gSticky steering unit valve.Flush or replace steering unit.Parking
Power steering fluid level low.Replenish fluid.
Excessive Wheel Kick Back or Loose
Steering
Air in system.Bleed hydraulic system.
SteeringTie rod end loose.Tighten tie rod end.
Wheel bearing worn.Replace wheel bearing.
Hard Steering or Lack or Power
Assist
Sticky steering unit valve.Flush or replace steering unit.
AssistInsufficient pump pressure.Repair pump assembly.
Excessive internal pump leakage.Repair pump assembly.
Excessive internal steering gear
leakage.Repair steering gear.
Power steering fluid level low.Replenish fluid.
Unstable Engine Idling or Stalling
When TurningPressure switch of the power
steering pump or its harness is faulty.Repair or replace.

2A±6
POWER±ASSISTED STEERING SYSTEM
Power Steering Pump
Foaming milky power steering fluid, low fluid level, and
possible low pressure can be caused by air in the fluid, or
loss of fluid due to internal pump leakage. Check for leak
and correct. Bleed the system. Extremely cold
temperatures will cause air bubbles in the system if thefluid level is low. If the fluid level is correct and the pump
still foams, remove the pump from the vehicle and check
housing for cracks. If the housing is cracked, replace the
pump housing.
Condition
Possible causeCorrection
Low Pressure Due to Steering PumpRelief valve sticking or inoperative.Replace relief valve.
Side plate not flat against cam ring.Replace side plate.
Extreme wear of cam ring.Replace cam ring.
Scored side plate or rotor.Replace side plate or rotor.
Vanes sticking in rotor slots.Repair or replace vanes and rotor.
Cracked or broken side plate.Replace side plate.
High internal leakage.Repair internal leakage.
Low Pressure Due to Steering GearScored housing bore.Replace housing.
Growling Noise In Steering PumpExcessive back pressure in hoses or
steering unit caused by restriction.Repair steering unit or pump.
Scored side plate or rotor.Replace side plate or rotor.
Worn cam ring.Replace cam ring.
Groaning Noise In Steering PumpAir in the fluid.Bleed hydraulic system.
Low fluid level.Replenish fluid.
Pump mounting loose.Tighten mounting bolt.
Rattling Noise In Steering PumpVanes sticking in rotor slots.Repair or replace vanes and rotor.
Vane improperly installed.Repair rotor and vane.
Swishing Noise In Steering PumpDamaged relief valve.Replace relief valve.
Whining Noise In Steering PumpScored side plate and vanes.Replace side plate and vanes.
Steering Column Lock System
ConditionPossible causeCorrection
Will Not UnlockDamaged lock cylinder.Replace lock cylinder.
Damaged park lock cable.Replace park lock cable.
Will Not LockLock spring broken or worn.Replace lock cylinder.
Damaged lock cylinder.Replace lock cylinder.
Ignition switch stuck.Repair or replace ignition switch.
Park lock cable damaged.Replace park lock cable.
Key Cannot be Removed in
ªOFF LOCKº
Ignition switch is not set correctly.Correct ignition switch.
ªOFF-LOCKºDamaged lock cylinder.Replace lock cylinder.
Faulty shift lock mechanism.Repair or replace the shift lock
mechanism.
Column
ConditionPossible causeCorrection
Noise in ColumnUniversal joint loose.Tighten joint.
Shaft lock snap ring not seated.Place snap ring in proper position.

2A±10
POWER±ASSISTED STEERING SYSTEM
The steering column has three important features in
addition to the steering function:
1. The column is energy absorbing, designed to
compress in a front-end collision to minimize the
possibility of injury to the driver of the vehicle.
2. The ignition switch and lock are mounted
conveniently on the column.
3. With the column mounted lock, the ignition and
steering operation can be locked to prevent theft of
the vehicle.The column can be disassembled and reassembled.
However, to insure the energy absorbing action, use only
the specified screws, bolts and nuts as designated, and
tighten them to the specified torque.
Handle the column with care when it is removed from the
vehicle. A sharp blow on the end of steering shaft or shift
lever, or dropping the assembly could shear or loosen the
fasteners that maintain column rigidity.
Power Steering System Test
Test Procedure
C02RW001
Legend
(1) Fluid Reservoir(2) Power Steering Unit
(3) Power Steering Pump
Test of fluid pressure in the power steering system is
performed to determine whether or not the oil pump and
power steering unit are functioning normally.
The power steering system test is used to identify and
isolate hydraulic circuit difficulties. Prior to performing
this test, the following inspections and corrections, if
necessary, must be made.

Inspect pump reservoir for proper fluid level.

Inspect pump belt for proper tension.

Inspect pump driver pulley condition. 1. Place a container under the pump to catch the fluid
when disconnecting or connecting the hoses.
2. With the engine NOT running, disconnect the
pressure hose at the power steering pump and install
power steering tester J-29877-A. The gage must be
between the shutoff valve and pump. Open the
shutoff valve.
3. Check the fluid level. Fill the reservoir with power
steering fluid, to the ªFullº mark. Start the engine,
then turn the steering wheel and momentarily hold it
against a stop (right or left). Turn the engine off and
check the connections at tester for leakage.

POWER±ASSISTED STEERING SYSTEM2A±11
4. Bleed the system. Refer to Bleeding the Power
Steering System
in this section.
5. Start the engine and check the fluid level. Add power
steering fluid if required. When the engine is at
normal operating temperature, increase engine
speed to 1500 rpm.
CAUTION: Do not leave shutoff valve fully closed
for more than 5 seconds, as the pump could become
damaged internally.
6. Fully close the shutoff valve. Record the highest
pressures.

If the pressure recorded is within 9300±9800 kPa
(1350±1420 psi), the pump is functioning within its
specifications.

If the pressure recorded is higher than 9800 kPa
(1420 psi), the valve in the pump is defective.

If the pressure recorded is lower than 9300 kPa
(1350 psi), the valve or the rotating group in the
pump is defective.
7. If the pump pressures are within specifications, leave
the valve open and turn (or have someone else turn)
the steering wheel fully in both directions. Record the
highest pressures and compare with the maximum
pump pressure recorded in step 6. If this pressure
cannot be built in either side of the power steering
unit, the power steering unit is leaking internally and
must be replaced.
8. Shut the engine off, remove the testing gauge.
9. Reconnect the pressure hose, check the fluid level
and make the needed repairs.
10. If the problem still exists, the steering and front
suspension must be thoroughly examined.
Maintenance
The hydraulic system should be kept clean and fluid level
in the reservoir should be checked at regular intervals and
fluid added when required. Refer to
Recommended
Fluids and Lubricants in General Information
section for
the type of fluid to be used and the intervals for filling.
If the system contains some dirt, flush it as described in
this section. If it is exceptionally dirty, the pump must be
completely disassembled before further usage. (The
steering unit cannot be disassembled.)
All tubes, hoses, and fittings should be inspected for
leakage at regular intervals. Fittings must be tight. Make
sure the clips, clamps and supporting tubes and hoses
are in place and properly secured.
Power steering hoses and lines must not be twisted,
kinked or tightly bent. Air in the system will cause spongy
action and noisy operation. When a hose is disconnected
or when fluid is lost, for any reason, the system must be
bled after refilling. Refer to
Bleeding the Power Steering
System
in this section.

Inspect belt for tightness.

Inspect pulley for looseness or damage. The pulley
should not wobble with the engine running.

Inspect hoses so they are not touching any other
parts of the vehicle.

Inspect fluid level and fill to the proper level.
Fluid Level
1. Run the engine until the power steering fluid reaches
normal operating temperature, about 55
C (130
F),
then shut the engine off.
2. Check the level of fluid in the reservoir.
3. If the fluid level is low, add power steering fluid as
specified in General Information to the proper level
and install the receiver cap.
4. When checking the fluid level after the steering
system has been serviced, air must be bled from the
system. Refer to
Bleeding the Power Steering
System
in this section.
Bleeding The Power Steering System
When a power steering pump or unit has been installed,
or an oil line has been disconnected, the air that has
entered the system must be bled out before the vehicle is
operated. If air is allowed to remain in the power steering
fluid system, noisy and unsatisfactory operation of the
system may result.
Bleeding Procedure
When bleeding the system, and any time fluid is added to
the power steering system, be sure to use only power
steering fluid as specified in General Information.
1. Fill the pump fluid reservoir to the proper level and let
the fluid settle for at least two minutes.
2. Start the engine and let it run for a few seconds. Do
not turn the steering wheel. Then turn the engine off.
3. Add fluid if necessary.
4. Repeat the above procedure until the fluid level
remains constant after running the engine.
5. Raise and support the front end of the vehicle so that
the wheels are off the ground.
6. Start the engine. Slowly turn the steering wheel right
and left, lightly contacting the wheel stops.
7. Add power steering fluid if necessary.
8. Lower the vehicle, set the steering wheel at the
straight forward position after turning it to its full steer
positions 2 or 3 times, and stop the engine.
9. Check the fluid level and refill as required.
10. If the fluid is extremely foamy, allow the vehicle to set
a few minutes, then repeat the above procedure.
Flushing The Power Steering System
1. Raise and support the front end of the vehicle off the
ground until the wheels are free to turn.
2. Remove the fluid return line at the pump inlet
connector and plug the connector port on the pump.
Position the line toward a large container to catch the
draining fluid.
3. While running the engine at idle, fill the reservoir with
new power steering fluid. Turn the steering wheel in
both directions. Do not contact or hold the steering
wheel to the wheel stops. This will cause the pump to
go to pressure relief mode, which may cause a
sudden fluid overflow at the reservoir.

2A±12
POWER±ASSISTED STEERING SYSTEM
4. Install all the lines and hoses. Fill the system with new
power steering fluid and bleed the system as
described in Bleeding The Power Steering System.
Operate the engine for about 15 minutes.
Remove the pump return line at the pump inlet and
plug the connection on the pump. While refilling the
reservoir, check the draining fluid for contamination.
If foreign material is still evident, replace all lines,
disassemble and clean or replace the power steering
system components. Do not re-use any drained
power steering fluid.
Steering Wheel Free Play Inspection
430R200001
1. With the tires in the straight-ahead position, check the
amount of steering wheel play by turning the wheel in
both directions until the tires begin to move.
NOTE: The wheel free play should be checked with the
engine running.
Free play: 0 ± 30 mm (0 ± 1.18 in)
2. Also check the steering wheel for play and looseness
in the mount by moving it back and forth and
sideways. When test driving, check for hard steering,
steering shimmy and tendency to pull to one side.
Front End Alignment Inspection and
Adjustment
General Description
ªFront End Alignmentº refers to the angular relationship
between the front wheels, the front suspension attaching
parts and the ground.
Proper front end alignment must be maintained in order to
insure efficient steering, good directional stability and to
prevent abnormal tire wear.
The most important factors of front end alignment are
wheel toe-in, wheel camber and axle caster.Camber:
This illustration shows view from the front of the vehicle.
480RS004Camber is the vertical tilting inward or outward of the front
wheels. When the wheels tilt outward at the top, the
camber is positive (+). When the wheels tilt inward at the
top, the camber is negative (-). The amount of tilt
measured in degrees from the vertical is called the
camber angle (1). If camber is extreme or unequal
between the wheels, improper steering and excessive tire
wear will result. Negative camber causes wear on the
inside of the tire, while positive camber causes wear to the
outside.
Caster:
This illustration shows view from the side of the vehicle.
480RS005

2A±18
POWER±ASSISTED STEERING SYSTEM
Power Steering Unit
Power Steering Unit and Associated Parts
440R100001
Legend
(1) Bracket
(2) Transfer Gear Assembly(3) Universal Joint Assembly
(4) Power Steering Unit Assembly
(5) Crossmember
Removal
1. Remove the stone guard.
2. Remove the transfer gear assembly and universal
joint assembly.
Make a setting mark across the coupling flange and
transfer gear assembly to ensure reassembly of the
parts in the original position.
3. Drain power steering fluid.
4. Remove the tie rod end assembly from knuckle.
Use tie rod end remover J±29107.
433RW002