clock ISUZU TF SERIES 2004 User Guide

BRAKES 5C-31

ADJUSTMENT PROCEDURE OF BRAKE PEDAL



The push rod serves as the brake pedal stopper when the
pedal is fully released.
Brake pedal height adjustment should be performed as follows.

RTW35CSH000601


Brake Pedal - Height
Measure the brake pedal height after making sure the pedal is
fully returned by the pedal return spring.
Note:
Pedal height (L2) must be measured after starting the
engine and increasing the revolution several times by
stepping on the accelerator pedal.
mm(in)

Pedal free play (L1) 6-10 (0.23 - 0.39)
M/T 174-186 (6.85-7.32)
RHD
LHD
A/T 176-188 (6.93-7.40) Height (L2)
Note:
Pedal free play must be measured after turning off the
engine and stepping on the brake pedal firmly five times
or more.
If the measured value deviates from the above range, adjust
the brake pedal as follows:
a) Disconnect the stop lamp switch.
b) Loosen the lock nut on the push rod.
c)
Adjust the brake pedal to the specified height by rotating the
push rod in the appropriate direction.



Lock Nut Torque N

m(kgf

m/lb
 
ft)
12 - 18 (1.2 – 1.8 / 9 - 13)

d) Install the stop lamp switch.

Note:
Pedal height (L
2) must be 80 mm (3.14 in.) or more when
applying about 50 kg (110.25 lbs.) of stepping force.

331R300005


How to connect the CLEVICE of BOOSTER ROD with PEDAL
ARM. and how to adjust the PEDAL SW.
After connecting the CLEVIS of BOOSTER ROD with PEDAL
ARM, adjust the PEDAL SW mounted (PDA) to PEDAL
BRACKET by the procedure explained still more bellow.
1. Set the hole of the CLEVIS of BOOSTER&M/CYL ROD
with the hole of the PEDAL ARM.
2. Enter the PIN; PUSH ROD to PEDAL to these holes
from left side of the PEDAL.
3. Enter and fix the PIN; SANP PIN FIX to the DITCH o
f
the PIN; PUSH ROD to PEDAL from right side of the
PEDAL.
4. Release the LOCK by turning the SWITCH counter-
clock-wise.

5C-32 BRAKES


5. After doing so, pull PEDAL ARM to yourself a little so
that PEDAL ARM is not pushed in.
6. Making PEDAL ARM not movable with one hand, push
in the whole SWITCH with the other hand until the
PLUNGER of SWTCH is pushed in and SWITCH itself
hits the RUBBER of PEDAL ARM.
In the condition, turn SWITCH clock-wise until “click”
sound is made and lock it.
By doing this the SWITCH is adjusted at 0.70.5mm
clearance.

CAB 10-31



13.Ashtray Case

Pull out the ashtray case.
14. Center Cluster Assembly
1) Pull out the cluster at the 6 clip positions.
2) Disconnect the cigarette lighter, accessory socket,
hazard switch and clock connectors.
15. Control Lever Assembly


Remove the 2 fixing screws.
17.Ashtray Bracket


Remove the 3 fixing screws and illumination connector.


Caution:
For precautions on installation or removal of SRS-air bag
system, refer to section 9 "Supplemental Restraint System
(SRS) - AIR BAG".
21. Passenger Air Bag



Remove 2 fixing bolts, 2 fixing nuts and connector.
22. Side Ventilation Grille.

Pull out the grilles and disconnect switch connecto
r
(Driver’s side).
23. Vent Duct Assembly/Defroster Nozzle Assembly


Refer to section 1 “HVAC” for defroster nozzle and
ventilation duct removal steps.




25. Instrument Panel


Remove the clip and 6 fixing bolts.
26. Cross Beam

CAB 10-59


Important Operations - Removal
1. Front Sill Plate



Pull out the 4 clip positions.


2. Fuel Filler Lid Opener Cover


Pull out the 3 clip positions.



3. Fuel Filler Lid Opener Lever


Remove the 2 opener fixing bolts and disconnect the
cable.



5. Fuel Filler Lid Cable Assembly


Remove some fixing clips, turn the cable holder on the
side of recess in 90counterclockwise and remove i
t
from the recess. Pull out the grommet to frontward o
f
vehicle and remove the cable assembly.

10-62 CAB



Important Operations - Removal
1. Front Sill Plate



Pull out 4 clip positions.
2. Rear Sill Plate


Pull out 2 clip positions.

4. Fuel Filler Lid Opener Cover


Pull out the 3 clip positions.



5. Fuel Filler Lid Opener Lever


Remove the 2 opener fixing bolts and disconnect the
cable.



7. Fuel Filler Lid Cable Assembly


Remove some fixing clips, turn the cable holder on the
side of recess in 90counterclockwise and remove i
t
from the recess. Pull out the grommet to frontward o
f
vehicle and remove the cable assembly.

CLUTCH 7C-31



Driven Plate Splined Hub Spline Wear
1. Clean the driven plate splined hub.
2. Install the driven plate to the transmission top gear shaf
t
spline.
3. Set a surface gauge to the driven plate outside
circumference.
4. Slowly turn the driven plate counterclockwise.
Measure the spline rotation play as you turn the driven
plate.
If the measured value exceeds the specified limit, the driven
plate assembly must be replaced.
Driven Plate Splined Hub Spline Wear mm(in)
Standard Limit
0.5 (0.020) 1.0 (0.039)



Rivet Head Depression
Use a depth gauge or a straight edge with steel rule to
measure the rivet head depression

1 from the facing surface

2.
Be sure to measure the rivet head depression on both sides of
the driven plate.
If the measured value is less than the specified limit, the facing
must be replaced.
Rivet Head Depression mm(in)

Standard
Fly wheel side P/Plate side Limit
4J 1.35-1.95
(0.053-0.077) 1.65-2.25
(0.065-0.089) 0.2
(0.008)
6VE1
C24SE 1.65-2.25
(0.065-0.089) 1.65-2.25
(0.065-0.089) 0.2
(0.008)

ELECTRICAL-BODY AND CHASSIS 8A-3
PAGE
Power Window ........................................................................................................... 8A- 310
Audio, Clock and Cigarette Lighter .......................................................................... 8A- 329
Power Door Mirror ...................................................................................................... 8A- 337
Rear Defogger ............................................................................................................ 8A- 349
SRS-Air Bag ................................................................................................................ 8A- 358
Transfer Case Control Module .................................................................................. 8A- 361
Anti-Lock Brake System ............................................................................................ 8A- 373
Immobilizer ................................................................................................................. 8A- 376
Keyless Entry ............................................................................................................. 8A- 385
Anti Theft ....................................................................................................................8A- 400
Auto Cruise ................................................................................................................. 8A- 412
Trailer Hitch ................................................................................................................ 8A- 415
Connector List ................................................................................................................8A- 418

8A-130 ELECTRICAL-BODY AND CHASSIS
FRONT TURN LIGHT
Removal
RTW38DSH000601

1. Turn the socket counterclockwise to disconnect it from the
front turn light housing.
2. Pull the bulb from the socket.


Installation
Follow the removal procedure in the reverse order to install the
front turn light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the clearance light connector is
securely connected.
This will prevent a poor contact and an open circuit.


CLEARANCE LIGHT
Removal
RTW38DSH000601

1. Turn the socket counterclockwise to disconnect it from the
clearance light housing.
2. Pull the bulb from the socket.


Installation
Follow the removal procedure in the reverse order to install the
clearance light.
Pay close attention to the important points mentioned in the
following paragraphs.



Connector
Be absolutely sure that the clearance light connector is
securely connected.
This will prevent a poor contact and an open circuit.

8A-142 ELECTRICAL-BODY AND CHASSIS

FRONT FOG LIGHT
Removal
1. Remove the radiator grille.
2. Remove the front bumper
3. Disconnect the fog light connector.
4. Remove the fog light.



5. Remove the bulb from the socket.
 Remove the socket by turning it counterclockwise.


Installation
Follow the removal procedure in the reverse order to install the
fog light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the fog light bulb is correctly installed.
This will prevent a poor contact and open circuit.


FRONT FOG LIGHT ADJUSTMENT
Vertical Adjustment
Turn the adjusting screw (1) with a screwdriver to adjust the
aim of the fog light vertically.



RTU4Z0SH000601
FRONT FOG & REAR FOG SWITCH

8A-148 ELECTRICAL-BODY AND CHASSIS




RTW48ASH000701

REAR FOG LIGHT
Removal
1. Remove the screws 1.
2. Remove the lens cover
2.
3. Rear fog push turn the bulb
3 counterclockwise to
disconnect it from the light housing.



Installation
Follow the removal procedure in the reverse order to install the
rear fog light.
Pay close attention to the important points mentioned in the
following paragraphs.



Bulb
Be absolutely sure that the license plate light bulb is correctly
installed.
This will prevent a poor contact and open circuit.




RTU4Z0SH000601
FRONT FOG & RR FOG SWITCH



RTW48ASH000401

Inspection
Check to see if there is any continuity between the terminals of
the leveling switch.
Replace the switch when the result of inspection is found
abnormal.

Removal
Preparation:
Disconnect the battery ground cable.
1. Ventilation grille
2. Harness connector
3. Front fog light & Rear fog light switch
To remove the switch, push the lock from the back side of
the cluster assembly.
4. Remove the bulb.