wheel ISUZU TF SERIES 2004 Workshop Manual

5D-10 PARKING BRAKE SYSTEM

Removal
1. Remove wheel and tire.
2. Remove brake drum.
3. Remove tension pin (1) and shoe clamp spring (2).
4. Remove return spring (3).
5. Remove shoe assemblly with parking brake leve
r
(4).
6. Remove shoe assembly with adjuster lever (5) and
spring (6).
7. Remove parking brake inner cable from parking
brake lever (4).
8. Use offset box wrench (12mm hex.) to compress
locking lugs on the cable, then remove parking
brake outer cable from back plate.
NOTE: Do not twist or bend the cable too much.
A damaged cable will cause poor operation or a cable
break down.





311RS012

Legend
(1) Offset Box Wrench (12mm hex)
9. Remove nut (8) to fix the cable (7) on the leaf
spring.
10. Take out parking brake rear cable (7) from the
back plate.
11. Remove bolt (9) and nut (10).
12. Disconnect T-end (11) from the equalizer of front
cable.

Installation
NOTE: Be sure to use the new shoe clamp spring (2)
and the new adjuster lever clip (14).
1. Apply grease (multipurpose type grease) to the
connecting portion of the rear cable (11) and
equalizer (13). (aroow mark).
2. Install parking brake outer cable in back plate and
inner cable in parking brake lever (4).
3. Install return spring (3).
4. Install shoe clamp spring (2) and tension pin (1)
5. Install shoe assembly with adjuster lever, shoe
assembly with parking brake lever (4) and spring
(6). ---- snap action
6. Install nut (8) and tighten it to the specified torque.
Torque: 7N




m (0.7 kg




m/61 lb in)
7. Connect T-end (11) with equalizer (13) through
outer cable retainer (12).
8. Install nut (10) and tighten it to the specifed
torque.
Torque: 15 N





m (1.5 kg





m/11 lb ft)
9. Install bolt (9) and tighten it to the specified
torque.
Torque: 7 N




m (0.7 kg




m/61 lb in)
10. Install brake drum.
11. Install wheel and tire.
12. Pull parking brake lever with a force equivalent to
poerating force: 490 N (50 kg/110 lb), 10 times fo
r
conditioning.
13. Adjust parking brake lever adjusting nut so that
parking brake lever goes through 8

14 (bench
seat) or 6

8 (bucket seat) notches, when pulled
with a operation force of 294N (30 kg/66 lb).
14. Check brake for no drag.

CAB 10-1
SECTION 10
CAB
TABLE OF CONTENTS
PAGE
Windshield.......................................................................................................................... 10- 2
Rear Window Assembly .................................................................................................... 10- 7
Front Door Assembly ........................................................................................................ 10- 10
Rear Door Assembly (Crew Cab) ...................................................................................... 10- 20
Instrument Panel................................................................................................................ 10- 28
Floor Console..................................................................................................................... 10- 34
Console Box (Without Floor Console) ............................................................................. 10- 38
Headlining .......................................................................................................................... 10- 39
Interior Trim Panels ...........................................................................................................10- 44
Fuel Filler Lid Opener Lever/Cable................................................................................... 10- 55
Quarter Glass (Extend Cab) .............................................................................................. 10- 70
Font Seat ............................................................................................................................ 10- 71
Rear Seat (Crew Cab) ........................................................................................................ 10- 74
Jump Seat (Extend Cab) ................................................................................................... 10- 75
Front Seat Belt ................................................................................................................... 10- 76
Rear Seat Belt (Crew Cab) ................................................................................................ 10- 80
Rear Seat Belt (Extend Cab) ............................................................................................. 10- 84
Front Wheel Extension ...................................................................................................... 10- 87
Rear Wheel Extension ....................................................................................................... 10- 88
Tail Gate Assembly ............................................................................................................ 10- 89

10-28 CAB
INSTRUMENT PANEL
REMOVAL


This illustration is based on RHD model
RTW4A0LF001001

Disassembly Steps

1. Front console assembly

2. Glove box

3. Instrument panel driver lower cover
assembly

4. Driver knee bolster assembly

5. Driver air bag

6. Steering wheel/ steering cowl

7. Meter cluster assembly
8. Dash side trim cover
9. Front pillar trim cover
10. Front cover
11. Side cover

12. Instrument panel & Cross beam
assembly


13. Ashtray case

14. Center cluster assembly

15. Control lever assembly
16. Storage box assembly

17. Ashtray bracket
18. Meter assembly
19. Passenger lower bracket
20. Glove box cover

21. Passenger air bag (if so equipped)

22. Side ventilation grille

23. Vent duct assembly/Defroster nozzle
assembly
24. Instrument harness assembly

25. Instrument panel

26. Cross beam

CAB 10-29

Important Operations
1. Front Console Assembly


Refer to Floor Consol in this section.



2. Glove Box


Remove 2 fixing screws and pulling the handle.



3. Instrument Panel Driver Lower Cover Assembly
1) Remove the engine hood opener 2 fixing screws.
2) Remove the lower cover one fixing screw.
3) Pull out the cover (Stick type parking brake only).
4) Pull out the lower cover assembly.




4. Driver Knee Bolster Assembly


Remove 4 fixing bolts.
Caution:
For precaution on installation or removal of SRS-air bag
system, refer to section 9 “Supplemental Restraint System
(SRS) - AIR BAG”

5. Driver Air Bag
6. Steering Wheel/Steering Cowl


Refer to Section 3B “STEERING COLUMN” for steering
lock assembly removal steps.




7. Meter Cluster Assembly


Pull out the 4 clip positions.

10-32 CAB
INSTALLATION


This illustration is based on RHD model
RTW4A0LF001101

Installation Steps
1. Cross beam
2. Instrument panel
3. Instrument harness assembly
4. Vent duct assembly/Defroster nozzle
assembly
5. Side ventilation grille
6. Passenger air bag
7. Glove box cover
8. Passenger lower bracket
9. Meter assembly
10. Ashtray bracket
11. Storage box assembly
12. Control lever assembly
13. Center cluster assembly


14. Ashtray case

15. Instrument panel & Cross beam
assembly
16. Side cover
17. Front cover
18. Front pillar trim cover
19. Dash side trim cover
20. Meter cluster assembly

21. Steering wheel/Steering cowl
22. Driver air bag
23. Driver knee bolster assembly
24. Instrument panel driver lower cover assembly
25. Glove box
26. Front console assembly

CAB 10-33
Important Operations
15. Instrument Panel & Crass Beam Assembly
1) Tighten the 4 bolts fixing the cross beam and body panel
to the specified torque.
Torque N
m (kgf
m/lb
ft)
19 (1.9/14)

2) A Bolt: Steering Column to Cross Beam
Torque N
m (kgf
m/lb
ft)
20 (2.0/14)
B Bolt: Pedal Bracket to Cross Beam
Torque N
m (kgf
m/lb
ft)
15 (1.5/11)


3) C Bolt: Parking Brake Bracket to Cross Beam
Torque Nm (kgfm/lbft)
15 (1.5/11)

21. Steering Wheel/Steering Cowl

Tighten the steering wheel fixing nut to the specified
truque.
Torque N
m (kgf
m/lb
ft)
35 (3.6/26)

CAB 10-55
FUEL FILLER LID OPENER LEVER/CABLE
REMOVAL (REGULAR CAB RHD MODEL)

686R300015

Removal Steps

1. Front sill plate

2. Fuel filler lid opener cover

3. Fuel filler lid opener lever
4. Rear wheel housing extension panel

5. Fuel filler lid cable assembly

10-56 CAB
FUEL FILLER LID OPENER LEVER/CABLE
REMOVAL (EXTEND CAB RHD MODEL)

686R300016

Removal Steps

1. Front sill plate

2. Fuel filler lid opener cover

3. Fuel filler lid opener lever
4. Rear wheel housing extension panel

5. Fuel filler lid cable assembly

CAB 10-57
FUEL FILLER LID OPENER LEVER/CABLE
REMOVAL (REGULAR CAB LHD MODEL)



RTW4A0LF000101

Removal Steps

1. Front sill plate

2. Fuel filler lid opener cover

3. Fuel filler lid opener lever
4. Rear wheel housing extension panel

5. Fuel filler lid cable assembly

10-58 CAB
FUEL FILLER LID OPENER LEVER/CABLE
REMOVAL (EXTEND CAB LHD MODEL)



RTW4A0LF000201

Removal Steps

1. Front sill plate

2. Fuel filler lid opener cover

3. Fuel filler lid opener lever
4. Rear wheel housing extension panel

5. Fuel filler lid cable assembly