service ISUZU TF SERIES 2004 Workshop Manual

6E-286 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
22

Using the DVM and check the VSS signal circuit.
Breaker box is available:
1. Ignition "Off", engine "Off".
2. Install the breaker box as type A (ECM
disconnected).
Refer to 6E-95 page.
3. Disconnect the immobilizer control unit connector (if
equipped).
4. Check the circuit for open or shot to ground circuit.
Was the problem found?
B32
Breaker Box


B-68






Breaker box is not available:
1. Ignition "Off", engine "Off".
2. Disconnect the immobilizer control unit connector (if
equipped) and ECM connector.
3. Check the circuit for open or short to ground circuit.
Was the problem found?
E-61(B)
B-68










-

Repair faulty
harness and
verify repair

Go to Step 25
23
Substitute a known good VSS and recheck.
Was the problem solved?
- Go to Step 24 Go to Step 25
24
Replace the VSS.
Was the problem solved?
- Verify repair Go to Step 25
25
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 26

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-287
Step Action Value (s) Yes No
26
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-290 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No


Breaker box is not available:
1. Ignition "Off", engine "Off".
2. Disconnect the ECM connector.
3. Check the circuit for open circuit.
Was the problem found?
E-60(A)












E-61(B)







-

Repair faulty
harness and
verify repair

Go to Step 9
9
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 10
10
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-291
DIAGNOSTIC TROUBLE CODE (DTC) P0563 (FLASH CODE 66)
SYSTEM VOLTAGE HIGH

Condition For Setting The DTC and Action Taken When The DTC Sets
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up)
66 P0563 A System Voltage High Battery voltage is above 16V for more than 20 seconds. No fail-safe function.

CIRCUIT DESCRIPTION
The engine control module (ECM) monitors the system
voltage on the ignition feed terminals to the ECM.
A
system voltage DTC will set whenever the voltage is
above a calibrated value.
DIAGNOSTIC AIDS
If the DTC sets when an accessory is operated, check
for a poor connection or defective accessory.


Diagnostic Trouble Code (DTC) P0563 (Flash Code 66)
System Voltage High

Step Action Value (s) Yes No
1
Was the "On-Board Diagnostic (OBD) System Check"
performed?
- Go to Step 2 Go to On Board
Diagnostic
(OBD) System
Check
2
1. Connect the Tech 2.
2. Review and record the failure information.
3. Select "F0: Read DTC Infor By Priority" in "F0:
Diagnostic Trouble Code".
Is the DTC P0563 stored as "Present Failure"?
- Go to Step 3 Refer to
Diagnostic Aids
and Go to Step
3
3
1. Using the Tech2, ignition "On" and engine "Off".
2. Select "Clear DTC Information" with the Tech2 and
clear the DTC information.
3. Operate the vehicle and monitor the "F5: Failed This
Ignition" in "F2: DTC Information"
Was the DTC P0563 stored in this ignition cycle?
- Go to Step 4 Refer to
Diagnostic Aids
and Go to Step
4
4
1. Using the Tech 2, ignition "On" and engine "On".
2. Monitor the "Ignition Voltage" in the data display.
3. Load the electrical system by turning on the
headlights, etc..
Does the Tech 2 indicate correct ignition voltage?
Less than 16VGo to Step 5 Check the
charging
system and Go
to Step 5
5
Is the battery jamp start cable incorrectly connecting?
- Verify
procedure Go to Step 6
6
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using the
"SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 7

6E-292 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
7
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if equipped)
must be linked to the ECM. Refer to section 11
“Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-293
DIAGNOSTIC TROUBLE CODE (DTC) P0601 (FLASH CODE 51)
CONTROL MODULE MEMORY CHECKSUM

Condition For Setting The DTC and Action Taken When The DTC Sets
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up)
51 P0601 A Control Module
Memory Checksum ECM memory area error. Engine control disabled.


CIRCUIT DESCRIPTION
The engine control module (ECM) used in this vehicle
utilizes an electrically erasable programmable read-only
memory (EEPROM). The EEPROM contains program
information and the calibrations required for engine,
transmission, and engine diagnostics operation.
Unlike the PROM used in past applications, the
EEPROM is not replaceable.

DIAGNOSTIC AIDS
 DTC P0601 indicates that the contents of the
EEPROM have changed since the ECM was
programmed. The only possible repair is ECM
replacement.


Diagnostic Trouble Code (DTC) P0601 (Flash Code 51)
Control Module Memory Checksum
Step Action Value (s) Yes No
1
Was the "On-Board Diagnostic (OBD) System Check"
performed?
- Go to Step 2 Go to On Board
Diagnostic (OBD)
System Check
2
1. Connect the Tech 2.
2. Review and record the failure information.
3. Select "F0: Read DTC Infor By Priority" in "F0:
Diagnostic Trouble Code".
Is the DTC P0601 stored as "Present Failure"?
- Go to Step 3 Refer to
Diagnostic Aids
and Go to Step 3
3
1. Using the Tech2, ignition "On" and engine "Off".
2. Select "Clear DTC Information" with the Tech2 and
clear the DTC information.
3. Operate the vehicle and monitor the "F5: Failed
This Ignition" in "F2: DTC Information"
Was the DTC P0601 stored in this ignition cycle?
- Go to Step 4 Refer to
Diagnostic Aids
4
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 5

6E-294 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
5
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-295
DIAGNOSTIC TROUBLE CODE (DTC) P0602 ECU PROGRAMMING ERROR

Condition For Setting The DTC and Action Taken When The DTC Sets
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up)
51 P0602 - ECU Programming
Error ECM memory area error. Engine control disabled.

CIRCUIT DESCRIPTION
The engine control module (ECM) used in this vehicle
utilizes an electrically erasable programmable read-only
memory (EEPROM). The EEPROM contains program
information and the calibrations required for engine,
transmission, and engine diagnostics operation.
Unlike the PROM used in past applications, the
EEPROM is not replaceable.

DIAGNOSTIC AIDS
Check for following conditions.
 When reprogramming operation is stopped unde
r
Service Programming System (SPS), DTC P0602 will
be set.
 When non programmed ECM (service ECM) is used
without Service Programming System (SPS), DTC
P0602 will be set.



Diagnostic Trouble Code (DTC) P0602 ECU Programming Error

Step Action Value (s) Yes No
1
Was the "On-Board Diagnostic (OBD) System Check"
performed?
- Go to Step 2 Go to On Board
Diagnostic (OBD)
System Check
2
1. Connect the Tech 2.
2. Review and record the failure information.
3. Select "F0: Read DTC Infor By Priority" in "F0:
Diagnostic Trouble Code".
Is the DTC P0602 stored as "Present Failure"?
- Go to Step 3 Refer to
Diagnostic Aids
3
Download the latest software to the ECM. "SPS
(Service Programming System) is necessary."
Is the action complete?
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-303
Step Action Value (s) Yes No
11
Using the DVM and check the IAC Valve circuit.
1. Ignition "On", engine "Off".
2. Disconnect the IAC Valve connector.
3. Check the circuit for short to power supply circuit.
Was the DVM indicate voltage?
E-70
VVVV






-
Repair faulty
harness and
verify repair
Go to Step 14
12
Substitute a known good IAC Valve and recheck.
Was the problem solved?
- Go to Step 13 Go to Step 14
13
Replace the IAC Valve.
Was the problem solved?
- Verify repair Go to Step 14
14
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 15
15
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-309
Step Action Value (s) Yes No


Breaker box is not available:
1. Ignition "Off", engine "Off".
2. Disconnect the TCM connector and ECM
connector.
3. Check the circuit for open or short to ground circuit.
Was the problem found?
E-60(A)










-

Repair faulty
harness and
verify repair

Go to Step 13
13
Is the ECM or TCM programmed with the latest
software release?
If not, download the latest software to the ECM or
TCM using the "SPS (Service Programming
System)".
Was the problem solved?
- Verify repair Go to Step 14
14
Replace the TCM.
Was the problem solved?
IMPORTANT: The replacement TCM must be
programmed. "SPS (Service Programming System)
is necessary."
- Verify repair Go to Step 15
15
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -