height ISUZU TF SERIES 2004 Owner's Manual

6A-78 ENGINE MECHANICAL (C24SE)

Adjustment Values/Checking Values

Valve clearance
Inlet Hydraulic valve lash adjustment
Outlet No adjustment necessary

Spark plugs - electrode gap 1.0  1.1mm

Compression The difference in compression
between the individual cylinders
in the engine must not exceed
100 kPa (1 bar).

Pressure loss The pressure loss of an engine
in perfect condition per cylinder
is not more than max. 25%
























Cylinder Head
Cylinder Head Gasket
Thickness - installed mm 1.2

Valve seat width at cylinder head
inlet mm 1.0 to 1.5
outlet mm 1.7 to 2.2

Valve stem play inlet mm 0.018 to 0.052
outlet mm 0.038 to 0.072

Permissible valve stem to cone runout
inlet mm 0.03
outlet mm 0.33

Overall height of cylinder head
(Sealing surface to sealing surface) mm 95.5  0.25

Installation height
inlet and
outlet valves mm 17.85 to 18.25
dimension "A" Distance Gauge
5-8840-2596-0

Installation height valve guide mm 83.50 to 83.80

Sealing surface peak-to-valley height mm max. 0.025

ENGINE MECHANICAL (C24SE) 6A-79
Cylinder Head (continued)
Valve System

Valve lifter valve play compensator
(hydraulic)

Valve rotators
(inlet or outlet) outlet

Valve play
(warm or cold) inlet mm 0
outlet mm 0

Cylinder head height mm 280.30.075
Cylinder head bottom, face parallelism mm 0.05
Valve Dimensions
C24SE
A in mm B in
mm C(diameter in mm) and identification mark D
1) 2) Normal K Oversize K1
0.075 Oversize K2
0.150 Oversize A
0.250
Inlet valve 104.2 103.8 41.8 7.012
6.998 7.087
7.073 7.162
7.148 7.262
7.248 44

Outlet valve 104.0 103.6 36.5 6.992
6.978 7.087
7.053 7.142
7.128 7.242
7.228 44

Valve stem
bore - 7.050
7.030 7.125
7.105 7.200
7.180 7.300
7.280 -
1) Production
2) Customer service
The P and A department only supplies valves with a length of 103.8mm (inlet valve) and 103.6mm (outlet valve)
only



Camshaft
2.4L
Identification letter K

Colour code Normal size -
0.1mm undersize violet

Radial runout mm 0.03

End play mm 0.09 to 0.21

Cam lift Inlet and outlet valve mm 6.67

ENGINE MECHANICAL (C24SE) 6A-81
Crankshaft, Cylinder Block

Cylinder Grinding and Piston Dimensions
Size Cylinder bore dia. in mm Cylinder to Related piston dia. in mm Piston head
Crankshaft co- efficient
housing
co-efficient
over to over to
Production
(2.4L) 1 87.48
87.49 87.49
87.50 99
00 87.46
87.47 87.47
87.48 99
00
Customer
service
(2.4L) - 87.99 88.00 0+0.5 87.97 87.98 7+0.5
Piston diameter must be measured at the position "D".
*inclusive


Cylinder Bore
Rebore cylinder Permissible oversize to 0.5mm (see parts
microfiche)

After reboring, invalidate original crankcase
housing coefficient and drive in new oversize
coefficient

Permissible out-of-round: 0.013mm
Permissible taper: 0.013mm
Measure out-of-round in bore at 4 different
heights
Piston projection above upper edge of cylinder block
0.40mm

Piston
Type Recessed pistons

Clearance For short-blocks and cylinder blocks with
complete pistons, the clearance is 0.02 to
0.04mm

For replacement (oversize), depending on
available pistons, a clearance of 0.02 to
0.04mm is permissible

6A-82 ENGINE MECHANICAL (C24SE)
Crankshaft, Cylinder Block (continued)
Piston Rings
2.4L
Square ring Height mm 1.2

Tapered ring Height mm 1.5

Oil scraper Height mm 2.5

Ring gap offset 180


Note that the upper steel band ring gap is offset 25 to 50mm to
the left and the lower 25 to 50mm to the right opposite the
intermediate ring gap.

Piston Pin

Length mm 61.5
Diameter mm 21
Type Shrunk into con-rod
Play mm 2.4L
in piston 0.010-0.015
in con-rod none
Installation When installing piston pins,
heat con-rods to approx.
280
C in oil bath. This
temperature should under no
circumstances be exceeded.


Crankshaft, Cylinder Block (continued)
The permissible weight variation of con-rods without piston and
bearing shell inside an engine is 8 g.
As the con-rods do not have balancing studs, reworking is not
possible.
Con-rods can only be replaced in sets.

6A-86 ENGINE MECHANICAL (C24SE)






Crankshaft, Cylinder Block (continued)
Flywheel
Starter ring gear Before fitting, heat ring gear to 180
C -
230
C

Lateral run-out Permissible lateral run-out of installed
starter ring gear to flywheel: 0.5mm

Precision turning Permissible removal of material in clutch
disc lining surface area: 0.3mm

In order to achieve the functional
relationship again after removal of material,
the same removal of material must take
place on the fore part of the flywheel
(contact for clutch assembly)

Dimension A: 2.1 to 2.2mm

Cylinder block
Top deck flatness mm 0.05
Cylinder block height mm 2710.075

SHEET METAL 2B-3



Important Operations - Removal
1. Washer Nozzle Tube

1) Open the hood.
2) Support the hood.
3) Remove the windshield washer nozzle tube.




2. Hood Hinge Bolts



Before removing
the hinges from the engine hood, scribe a
mark showing location of
the hinges to facilitate installation in
the original position.

RTW32BSH000101

Important Operations - Installation
3. Engine Hood


Check the engine hood and fender. (1)




Clearance : 4.0 mm (0.16 in)


Height (step) : Flushness


Adjust clearance with the hinges on the engine hood.











Adjust height (step) with the hood rests (1).






Engine Hood Striker


Apply a light coat of grease to the striker.

SHEET METAL 2B-9

RTW32BSH000201


2) Check the fender and front door (1).


Clearance : 5.0 mm (0.2 in)


Height (step) : Flushness

RTW32BSH000301

MSG MODEL 7B-25
INSPECTION AND REPAIR

Make the necessary adjustments, repairs, and part replacements if excessive wear or damage is discovered during
inspection.






SHIFT ARM THICKNESS
Use a micrometer to measure the shift arm thickness.
If the measured value is less than the specified limit, the shift
arm must be replaced.
Shift Arm Thickness mm(in)
Standard Limit
1st-2nd 9.6-9.8 (0.378-0.386) 9.0 (0.354)
3rd-4th 6.95-7.2 (0.273-0.283) 6.5 (0.256)
Rev.-5th 6.8-6.9 (0.268-0.272) 6.3 (0.248)





DETENT SPRING FREE LENGTH
Use a venier caliper to measure the detent spring free length.
If the measured value is less than the specified limit, the
detent spring must be replaced.
Detent Spring Free Length mm(in)
Standard Limit
25.6 (1.01) 23.6 (0.93)





DETENT SPRING TENSION
Use a spring tester to measure the valve spring tension.
If the measured value is less than the specified limit, the valve
spring must be replaced.
Valve Spring Tension N(kg/lb)
Compressed
Height mm(in)Standard Limit
22.1 (0.870)61.8-65.7
(6.3-6.7/13.9-14.8)55.9
(5.7/12.6)




BLOCK RING AND DOG TEETH
CLEARANCE
Use a thickness gauge to measure the clearance between the
block ring and the dog teeth.
If the measured value exceeds the specified limit, the block
ring must be replaced.
Block Ring and Dog Teeth Clearance mm(in)
Standard Limit
1st,2nd 2.0 (0.078) 1.3 (0.051)
3rd, 4th, 5th 1.5 (0.059) 0.8 (0.032)

MANUAL TRANSMISSION 7B1-25

Inspection and Repair
Make the necessary adjustments, and part
replacements if excessive wear or damage is
discovered during inspection.
Shift Arm Thickness

Use a micrometer to measure the shift arm
thickness.
If the measured value is less than the specified limit,
the shift arm must be replaced.

Shift Arm Thickness
Standard Limit
1st-2nd 9.60 - 9.85 mm
(0.378 - 0.388 in)
3rd-4th
Rev.5th 9.60 - 9.80 mm
(0.378 - 0.386 in) 9.0 mm
(0.354 in)


230RS006
Detent Spring Free Length

Use a vernier caliper to measure the detent spring
free length.
If the measured value is less than the specified limit,
the detent spring must be replaced.

Detent Spring Free Length
Standard Limit
26.8 mm (1.06 in) 26.2 mm (1.03 in)


SOUTH AFRICA 5th-Rev Only
Detent Spring Free Length
Standard Limit
Outer 27.6 mm (1.09 in) 27.0 mm (1.06 in)
Inner 26.6 mm (1.05 in) 26.0 mm (1.02 in)

220RS012
Detent Spring Tension


Use a spring tester to measure the detent spring
tension.
If the measured value is less than the specified limit,
the detent spring must be replaced.

Detent Spring Tension
Compressed height Standard
20 mm (0.787 in) 87.2 - 97.1 N
(19.6 - 21.8 lb)

220RS013

SOUTH AFRICA 5th-RV Only
Detent Spring Free Length
Compressed Standard
Outer 20 mm (0.787 in) 93.5 – 103.3 N
(21.0 – 23.3 lb)
Inner 20 mm (0.787 in) 26.4 – 36.3 N
(5.9 – 8.2 lb)

MANUAL TRANSMISSION 7B1-83

Inspection and Repair
Make the necessary adjustments, and part
replacements if excessive wear or damage is
discovered during inspection.
Shift Arm Thickness

Use a micrometer to measure the shift arm
thickness.
If the measured value is less than the specified limit,
the shift arm must be replaced.

Shift Arm Thickness
Standard Limit
1st-2nd 9.60 - 9.85 mm
(0.378 - 0.388 in)
3rd-4th
Rev.5th 9.60 - 9.80 mm
(0.378 - 0.386 in) 9.0 mm
(0.354 in)

230RS006
Detent Spring Free Length


Use a vernier caliper to measure the detent spring
free length.
If the measured value is less than the specified limit,
the detent spring must be replaced.

Detent Spring Free Length
Standard Limit
26.8 mm (1.06 in) 26.2 mm (1.03 in)


SOUTH AFRICA 5th-Rev Only
Detent Spring Free Length
Standard Limit
Outer 27.6 mm (1.09 in) 27.0 mm (1.06 in)
Inner 26.6 mm (1.05 in) 26.0 mm (1.02 in)

220RS012
Detent Spring Tension


Use a spring tester to measure the detent spring
tension.
If the measured value is less than the specified limit,
the detent spring must be replaced.

Detent Spring Tension
Compressed height Standard
20 mm (0.787 in) 87.2 - 97.1 N
(19.6 - 21.8 lb)

220RS013


SOUTH AFRICA 5th-RV Only
Detent Spring Free Length
Compressed Standard
Outer 20 mm (0.787 in) 93.5 – 103.3 N
(21.0 – 23.3 lb)
Inner 20 mm (0.787 in) 26.4 – 36.3 N
(5.9 – 8.2 lb)