Tcm ISUZU TF SERIES 2004 Owner's Guide

6E-312 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
7
Using the DVM and check the CAN BUS high circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the TCM connector.
3. Ignition "On".
4. Check the circuit for short to power supply circuit.
Was the problem found?


V



-
Repair faulty
harness and
verify repair
Go to Step 8
8
Using the DVM and check the CAN BUS low circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the TCM connector.
3. Ignition "On".
4. Check the circuit for short to power supply circuit.
Was the problem found?


V



-
Repair faulty
harness and
verify repair
Go to Step 9
9
Using the DVM and check the ECM CAN BUS circuit.
1. Ignition "Off", engine "Off".
2. Disconnect TCM connector.
3. Measure the resistance of ECM CAN BUS circuit.
Does the tester indicate standard resistance?






Approximately
120
Go to Step 14
Close to 0: Go
to Step 10
No resistance:
Go to Step 11

6E-314 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
11

Using the DVM and check the CAN BUS high circuit.
Breaker box is available:
1. Ignition "Off", engine "Off".
2. Install the breaker box as type A (ECM
disconnected).
Refer to 6E-95 page.
3. Disconnect the TCM connector.
4. Check the circuit for open or short to ground circuit.
Was the problem found?
A10
Breaker Box







Breaker box is not available:
1. Ignition "Off", engine "Off".
2. Disconnect the TCM connector and ECM
connector.
3. Check the circuit for open or short to ground circuit.
Was the problem found?
E-60(A)










-

Repair faulty
harness and
verify repair

Go to Step 12

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-315
Step Action Value (s) Yes No
12

Using the DVM and check the CAN BUS low circuit.
Breaker box is available:
1. Ignition "Off", engine "Off".
2. Install the breaker box as type A (ECM
disconnected).
Refer to 6E-95 page.
3. Disconnect the TCM connector.
4. Check the circuit for open or short to ground circuit.
Was the problem found?
A11
Breaker Box







Breaker box is not available:
1. Ignition "Off", engine "Off".
2. Disconnect the TCM connector and ECM
connector.
3. Check the circuit for open or short to ground circuit.
Was the problem found?
E-60(A)










-

Repair faulty
harness and
verify repair

Go to Step 13
13
Is the ECM or TCM programmed with the latest
software release?
If not, download the latest software to the ECM or
TCM using the "SPS (Service Programming
System)".
Was the problem solved?
- Verify repair Go to Step 14
14
Replace the TCM.
Was the problem solved?
IMPORTANT: The replacement TCM must be
programmed. "SPS (Service Programming System)
and is necessary."
- Verify repair Go to Step 15

ENGINE DRIVEABILITY AND EMISSIONS 6E–85
2. Demand of Data
1. Connect Tech-2 to the vehicle. When activated by
turning on the power of Tech-2, push the “Enter”
switch.
2. Turn on the ignition switch (without starting the
engine)
3. In the main menu of Diagnostic Tester, push “F1:
Service Programming System (SPS)”.
4. Push “F0: Request Info” of Tech-2.5. Where vehicle data has been already saved in Tech
2, the ex isting data come on display. In this
instance, as Tech-2 starts asking whether to keep
the data or to continue obtaining anew data from the
control unit, choose either of them
6. If you select “continue”, you have to select “Model
Year”, “Vehicle Type”.
7. After that. then push button and turn Ignition switch
tuned on, off, on following Tech-2 display. Tech-2
will read information from controller after this
procedure.
8. During obtaining information, Tech-2 is receiving
information from the control unit ECM and TCM (A/T
only) at the same time. With VIN not being
programmed into the new control unit at the time of
shipment, "obtaining information" is not complete
(because the vehicle model, engine model and
model year are specified from VIN). For the
procedure get additional information on vehicles,
instruction will be provided in dialog form, when
TIS2000 is in operation.
9. Following instructions by Tech-2, push the “Ex it”
switch of Tech-2, turn off the ignition of the vehicle
and turn off the power of Tech-2, thereby removing
from the vehicle.3. Data Exchange
1. Connect Tech-2 to P/C, turn on the power and click
the “Next” button of P/C.
2. Check VIN of the vehicle and choose “Next”.
3. Select “System Type” for required control unit.
Engine (Programming for ECM or PCM)
Transmission (Programming for TCM)
4. When a lack of data is asked from among the
following menu, enter accordingly.
Select following Menu
Model Year
Model
Engine type
Transmission type
Destination code (vehicles for general export)*1
Immobilizer
Etc.
* 1: How to read the destination code
Destination code can be read from ID Plate affix ed on
vehicles, while on VIN plate the destination code is
described at the right-hand edge of Body Type line. In
the figure, the destination code can be read as "RR3"
(Australia).

TRANSFER CONTROL SYSTEM 7D1-31
CONNECTOR LIST
No. Connector face No. Connector face
B-24
Green
Meter-B C-57
(4JH1-
TC)
ECM
B-54
White
J/B I2 C-67
BlackEHCU
B-62
White
Ignition switch (IGSUB : G1) C-94
(4JH1-
TC)
Gray TCM
B-63
White
Ignition switch (IGSUB : G2) C-95
(6VE1)
WhiteTCM
B-64
Silver
Weld splice 1(Illumination) C-107
WhiteJ/B E2
B-65
Silver
Weld splice 2 (Ground) C-108
WhiteJ/B E1
B-66
White
4WD switch C-109
SilverBody-LH ; ground
C-2
Silver
Engine room-RH ; Ground C-118
(4JH1-
TC)
WhiteA/C Resister & Neutral switch
C-36
Silver
Engine room-LH ; Ground C-119
(6VE1)
BlackAuto cruise actuator
C-56
(4JH1-
TC)
Gray
ECM R-15
BlackTransfer controller

TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L) 7A2-1
TRANSMISSION
TRANSMISSION CONTROL SYSTEM (AW30–40LE) (V6 3.5L)
CONTENTS

Service Precaution .................................................
7A2-2
General Description ...............................................
7A2-2
Electronic Control Diagram ...............................
7A2-3
Transmission Control Module (TCM) (1/2) ......
7A2-4
Transmission Control Module (TCM) (2/2) ......
7A2-5
TCM Point Table .................................................
7A2-6
TCM Voltage & Resistance Check Sheet .......
7A2-7
Control System Diagram ....................................
7A2-9
Control and Functions ........................................
7A2-10
Gear Shift Control 3rd start ...............................
7A2-10
Mode Type ...........................................................
7A2-10
Mode Selection ....................................................
7A2-10
Comparison of mode ..........................................
7A2-11
3rd start Mode .....................................................
7A2-11
Backup Mode .......................................................
7A2-11
Functions of Input / Output Components ........
7A2-12
CAN bus systems in automatic transmission
control (AW30-40LE) ........................................
7A2-13
High speed CAN bus ..........................................
7A2-13
Diagnosis .................................................................
7A2-13
Electronic Diagnosis ...........................................
7A2-13
Check Trans Indicator ........................................
7A2-13
On Board Diagnostic Check ..............................
7A2-13
"Check Trans" Check .........................................
7A2-14
Tech 2 OBD Connection ....................................
7A2-17
Snapshot Display With TIS2000 .................. 7A2-23
Service Programming System (SPS)............. 7A2-27
OBD Diagnostic Management System ............
7A2-30
16 - Terminal Data Link Connector (DLC) ......
7A2-31
Clear DTC ............................................................
7A2-32
DTC Check ..........................................................
7A2-32
TCM Precaution ..................................................
7A2-32
Information On TCM ...........................................
7A2-32
TCM Diagnostic Trouble Codes ........................
7A2-33
DTC P0560 (FLASHING CODE 25)
System Voltage Error ...........................................
7A2-34

DTC P0602 (FLASHING CODE 63)
Transmission Control Module (TCM)
Programming Error ................................................
7A2-36
DTC P0705 (FLASHING CODE 17)
Transmission Range Sensor Circuit
Malfunction .............................................................
7A2-38
DTC P0712 (FLASHING CODE 15)
Transmission Oil Temperature Sensor
Circuit Low Input ....................................................
7A2-42
DTC P0713 (FLASHING CODE 16)
Transmission Oil Temperature Sensor
Circuit Hight Input ..................................................
7A2-45
DTC P0717 (FLASHING CODE 14)
Input Speed Sensor Signal Error .........................
7A2-48
DTC P0722 (FLASHING CODE 11)
Output Speed Sensor Signal Error .....................
7A2-51
DTC P0743 (FLASHING CODE 33)
Torque Converter Clutch Electrical .....................
7A2-54
DTC P0748 (FLASHING CODE 35)
Pressure Control Solenoid Electrical ..................
7A2-57
DTC P0753 (FLASHING CODE 31)
Shift Solenoid S1 Electrical ..................................
7A2-60
DTC P0758 (FLASHING CODE 32)
Shift Solenoid S2 Electrical ..................................
7A2-63
DTC P1767 (FLASHING CODE 67)
ECM CAN Invalid ...................................................
7A2-66
DTC P1790 (FLASHING CODE 61)
Transmission Control Module ROM
Checksum Error .....................................................
7A2-69
DTC P1791 (FLASHING CODE 62)
Transmission Control Module RAM
Error .........................................................................
7A2-71
DTC U2104 (FLASHING CODE 65)
CAN BUSS OFF ....................................................
7A2-73

7A2-4 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

Transmission Control Module (TCM) (1/2)




RTW48AXF028101

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-5

Transmission Control Module (TCM) (2/2)








RTW48AXF003101

7A2-6 TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L)

TCM Point Table



RTW37ASF000101-1


PIN No. SIGNAL NAME
A1 GND
A2 PRESSURE CONTROL SOLENOID GND
A3 —
A4 PRESSURE CONTROL SOLENOID
A5 L-up SOLENOID
A6 STARTER SW(IG1)
A7 CAN COMMUNICATION (-)
A8 —
A9 —
A10 —
A11 T/M OIL TEMPERATURE SENSOR
A12 T/M OIL TEMPERATURE SENSOR GND
A13 —
A14 —
A15 SHIFT SOLENOID (S2)
A16 SHIFT SOLENOID (S1)
A17 CAN COMMUNICATION (+)
A18 —
A19 —
A20 —
A21 —
A22 —
A23 GND
A24 BATTERY

PIN No. SIGNAL NAME
B1 NEUTRAL START SW (R)
B2 POWER LAMP
B3 CHECK TRANS LAMP
B4 PATTERN SELECT SW (3rd START)
B5 SPEED SENSOR (+)
B6 INPUT REVOLUTION SENSOR (+)
B7 NEUTRAL START SW (D)
B8 NEUTRAL START SW (N)
B9 NEUTRAL START SW (3)
B10 3rd START LAMP
B11 OIL TEMPERATURE WARNING LAMP
B12 DIAGNOSIS TERMINAL
B13 PATTERN SELECT SW (POWER)
B14 SPEED SENSOR (-)
B15 —
B16 INPUT REVOLUTION SENSOR (+)
B17 —
B18 NEUTRAL START SW (L)
B19 NEUTRAL START SW (2)
B20 NEUTRAL START SW (P)
B21 TRANSMISFER LOW 4 SW
B22 BRAKE LAMP SW
B23 DIAGNOSIS OUT PUT
B24 —
B25 —
B26 CRUISE CONTROL UNIT

TRANSMISSION CONTROL SYSTEM (AW30 –40LE) (V6 3.5L) 7A2-7

TCM Voltage & Resistance Check Sheet
CHECK ITEM PIN No. VALUE NOTE
VIGN A6 –A1 VIGN
Key “ON ”

A6 –A23 VIGN
Key “ON ”
Backup Power Supply A24 –A1 +B (Always)
Key “ON ”
Inhibitor (Select) SW P B20 –A1 “P ” Range VIGN Key “ON ”

Except “P ” 0V
Inhibitor (Select) SW R B1
–A1 “R ” Range VIGN Key “ON ”

Except “R ” 0V
Inhibitor (Select) SW N B8
–A1 “N ” Range VIGN Key “ON ”

Except “N ” 0V
Inhibitor (Select) SW D B7
–A1 “D ” Range VIGN Key “ON ”

Except “D ” 0V
Inhibitor (Select) SW 2 B19
–A1 “2 ” Range VIGN Key “ON ”

Except “2 ” 0V
Inhibitor (Select)SW 1 B18
–A1 “1 ” Range VIGN Key “ON ”

Except “1 ” 0V
Inhibitor (Select) SW 3 B9
–A1 “3 ” Range VIGN Key “ON ”

Except “3 ” 0V
Power SW B13
–A1 ON 0V Key “ON ”

OFF VIGN
3rd Start SW B4
–A1 ON 0V Key “ON ”

OFF VIGN
Brake SW B22
–A1 ON VIGN Key “ON ”

OFF 0V
AT Oil Temperature
Sensor A11
–A12 20
C 4.6V Engine run.

155

C 1.1V
4L Signal B21
–A1 4L 0V Key “ON ”

2H/4H VIGN
Diag SW B12
–A1 ON VIGN Key “ON ”

OFF 0V
Shift Solenoid A (S1) A16
–A1 P VIGN Engine run.

R VIGN

N VIGN

D –1 VIGN

D –2 VIGN

D –3 0V

D –4 0V