sensor ISUZU TF SERIES 2004 Workshop Manual

6E-360 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
11
1. Using a Tech 2, display the ECT sensor and IAT
sensor value.
2. Check the specified value or wire.
Was the problem found?
- Verify repair Go to Step 12
12
1. Remove the spark plugs and check for gas or oil
fouling cracks, wear, improper gap, burned
electrodes, heavy deposits, or improper heat
range.
2. If spark plugs are fouled, the cause of fouling must
be determined before replacing the spark plugs.
Was a problem found?
- Verify repair Go to Step 13
13
Check for proper calibration of the speedometer.
Does the speed indicated on the speed meter closely
match the vehicle speed displayed on the Tech 2?
- Go to Step 15 Go to Step 14
14
Diagnose and repair the inaccurate speedometer
condition as necessary. Refer to Vehicle Speed
Sensor in Electrical Diagnosis.
- Verify repair -
15
Check for proper calibration of the fuel gauge.
Was a problem found?
- Verify repair Go to Step 16
16
Check for the following engine mechanical problems
(refer to Engine Mechanical):

Low compression.

Worn camshaft.

Sticking or leaking valves.

Valve timing.
Was a problem found?
- Verify repair Go to Step 17
17
1. Review all diagnostic procedures within this table.
2. If all procedures have been completed and no
malfunctions have been found, review/inspect the
following:

Visual/physical inspection.

Tech 2 data.

All electrical connections within a suspected circuit
and/or system.
Was a problem found?
- Verify repair Go to Step 18
18
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 19

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-363
Step Action Value (s) Yes No
14
Check the EVAP purge solenoid valve operation.
Is the valve operated normally?
- Verify repair &
Go to Step 17 Verify repair &
Go to Step 15
15
Check the exhaust system for a possible restriction:

Damaged or collapsed pipes.

Internal catalytic converter failure.
Was a problem found?
- Verify repair &
Go to Step 17 Go to Step 16
16
1. Remove excessive carbon buildup with a top
engine cleaner. Refer to the instructions on the top
engine cleaner can.
2. Perform the exhaust emission test.
Does the vehicle pass the test?
- System OK Go to Step 18
17
Perform the exhaust emission test.
Does the vehicle pass the test?
- System OK Go to Step 18
18
Check the fuel control Heated Oxygen Sensor
(HO2S). When monitored on the Tech 2, the HO2S
should respond quickly to different throttle positions. If
it doesn't check for silicon or other contaminates from
fuel or use of improper sealant. The sensors may have
a white powdery coating. Silicon contamination sends
a rich exhaust signal which causes the ECM to
command and excessively lean air/fuel mixture.
Was a problem found?
- Verify repair Go to Step 19
19
Monitor "B1S1 (Bank 1 Sensor 1) Status" and "B2S1
(Bank 2 Sensor 1) Status" on the Tech 2.
Is the "B1S1 (Bank 1 Sensor 1) Status" or "B2S1
(Bank 2 Sensor 1) Status" in the rich condition?
- Go to Step 20 Go to Step 21
20
Check items that can cause the engine to run rich.
Refer to DTC P0172 "O2 Sensor System Too Rich
(Bank 1)" or DTC P0175 "O2 Sensor System Too Rich
(Bank 2)".
Was a problem found?
- Verify repair Go to Step 22
21
Check items that can cause the engine to run lean.
Refer to DTC P0171 "O2 Sensor System Too Lean
(Bank 1)" or DTC P0174 "O2 Sensor System Tool
Lean (Bank 2)".
Was a problem found?
- Verify repair Go to Step 22
22
Check for the following engine mechanical problems
(refer to Engine Mechanical):

Low compression.

Leaking cylinder head gaskets.

Worn camshaft. -Sticking or leaking valves.

Valve timing. -Broken valve springs.
Was a problem found?
- Verify repair Go to Step 23

6E-366 3.5L ENGINE DRIVEABILITY AND EMISSIONS
BACKFIRE SYMPTOM
DEFINITIONS: Fuel ignites in the intake manifold, or in
the exhaust system, making a loud popping noise.



Step Action Value (s) Yes No
1
Was the "On-Board Diagnostic (OBD) System Check"
performed?
- Go to Step 2 Go to On Board
Diagnostic (OBD)
System Check
2
1. Perform a bulletin search.
2. If a bulletin that addresses the symptom is found,
correct the condition as instructed in the bulletin.
Was a bulletin found that addresses the symptom?
- Verify repair Go to Step 3
3
Was a visually/physical check performed?
- Go to Step 4 Go to Visual /
physical Check.
4
Check for proper ignition voltage output with the spark
tester.
Was a problem found?
- Verify repair Go to Step 5
5
Check the ignition coils for cracks or carbon tracking.
If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 6
6
1. Remove the spark plugs and check for gas or oil
fouling cracks, wear, improper gap, burned
electrodes, heavy deposits, or improper heat
range.
2. If spark plugs are fouled, the cause of fouling must
be determined before replacing the spark plugs.
Was a problem found?
- Verify repair Go to Step 7
7
Check the fuel pressure. Refer to Fuel System
Pressure Test.
Was a problem found?
- Verify repair Go to Step 8
8
Refer to 6E-116 page Fuel System Diagnosis to
determine if there is a problem with fuel delivery.
Was a problem found?
- Verify repair Go to Step 9
9
Check the CKP sensor signal, shield wire, or
installation condition. Refer to DTC P0336 "Crankshaft
Position Sensor Circuit Range/Performance" and DTC
P0337 "Crankshaft Position Sensor Circuit No Signal".
Was a problem found?
- Verify repair Go to Step 10

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-369
CRANKSHAFT POSITION (CKP)
SENSOR

Location
Right-hand side of the cylinder block.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect connector from the CKP sensor.
3. Loosen a bolt and remove the CKP sensor from
the cylinder block.
NOTE:
Use caution to avoid any hot oil that might drip out.




Installation Procedure
1. Install the CKP sensor to the cylinder block.
Before installation, apply small amount of engine
oil to the O-ring.
2. Tighten CKP sensor by a bolt with specified
tightening torque.
Tightening Torque





Bolt: 10N




m (1.0kgf




m).
3. Connect a sensor connector to the CKP sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.

CAMSHAFT POSITION (CMP)
SENSOR

Location
The rear of right bank of the cylinder head.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect connector from the CMP sensor.
3. Loosen a bolt and remove the CMP sensor from
the cylinder head.





Installation Procedure
1. Install the CMP sensor to the cylinder head.
Before installation, apply small amount of engine
oil to the O-ring.
2. Tighten CMP sensor by a bolt with specified
tightening torque.
Tightening Torque





Bolt: 10N




m (1.0kgf




m)
3. Connect a sensor connector to the CMP sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.

6E-370 3.5L ENGINE DRIVEABILITY AND EMISSIONS
ENGINE COOLANT TEMPERATURE
(ECT) SENSOR

Location
Installed to the thermostat housing.

Removal Procedure
1. Disconnect the negative battery cable.
2. Drain enough engine coolant so that the coolan
t
level will be below the ECT sensor.
3. Disconnect connector from the ECT sensor.
4. Loosen and remove the ECT sensor from the
thermostat housing.
NOTE:
Cool down the engine before above procedures are
carried out.










Installation Procedure
1. Apply sealer to threads of screw at the ECT
sensor.
2. Tighten the ECT sensor with specified tightening
torque.
Tightening Torque





13N




m (1.3kgf




m)
3. Connect a ECT sensor connector to the ECT
sensor.
4. Fill the engine coolant.
5. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.
Verify no engine coolant leaking from the senso
r
threads after replacement.


MASS AIR FLOW (MAF) SENSOR &
INTAKE AIR TEMPERATURE (IAT)
SENSOR
Location
Installed to the intake duct housing.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect a MAF & IAT sensor connector from
the MAF & IAT sensor.
3. Loosen two screws and remove the MAF & IAT
sensor from the intake duct.





Installation Procedure
1. Install the MAF & IAT sensor into intake air duct.
2. Tighten MAF & IAT sensor by two screws.
Tightening Torque : 1.5 N




m (0.15 kgf




m)
3. Connect a sensor connector to the MAF & IAT
sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-371
THROTTLE POSITION SENSOR
(TPS)

Location
Installed on the throttle body.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the TPS connector.
3. Loosen two screws and remove TPS from the
throttle body.




Installation Procedure
1. Temporary tighten the TPS by two screws.
2. Connect a TPS connectors to the TPS.
3. Connect the Tech2 to the vehicle.
4. Connect the negative battery cable.
5. Select "Data Display" with the Tech2.
6. Check the throttle position data and adjust the TPS
position.
7. Tighten two screws.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.



IDLE AIR CONTROL (IAC) VALVE

Location
Installed on the throttle body.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the IAC valve connector.
3. Loosen two screws and remove IAC valve from
the throttle body.




Cleaning and Inspection
1. Clean the IAC valve O-ring sealing surface, pintle
valve seat and air passage.
2. Use carburetor cleaner and a parts cleaning brush
to remove carbon deposit.
Do not use a cleaner that contain methyl ethyl
ketone. This is an extremely strong solvent and no
t
necessary for this type of deposit.
3. Shiny spots on the pintle are normal and do no
t
indicate misalignment or a bent pintle shaft.
4. Inspect the IAC valve O-ring for cuts, cracks o
r
distortion.

6E-372 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Measurement
In order to install a new IAC valve, messier the distance
between the tip of the pintle and the mounting flange. I
f
that measurement is 28mm (1.1in.) or less, the valve
need no adjustment. If the measurement is greater than
28mm (1.1in.), apply finger pressure and retract the
valve. The force required to retract the pintle on a ne
w
valve will not damage the valve, shaft, or pintle.




28mm(1.1in.)
or less


Installation Procedure
1. Tighten the IAC valve by two screws.
2. Connect a IAC valve connector to the IAC valve.
3. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.


HEATED OXYGEN SENSOR (HO2S)

Location
Installed on the exhaust pipe for each bank.

Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the O2 sensor connector.
3. Loosen and remove the O2 sensor from the
exhaust pipe.



Bank 1 Heated Oxygen Sensor (Right bank)



Bank 2 Heated Oxygen Sensor (Left bank)

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-373
Inspection
 Inspect the louvered end of the sensor for grease,
dirt, excessive carbon build up or othe
r
contamination.
 A special anti-seize compound is used on the O2
sensor threads. This compound consists of glass
breads suspended in a liquid graphite solution.
The graphite burns away with engine heat, but the
glass breads will remain, marking the senso
r
easier to remove.
 New or service sensors will already have the
compound applied to the threads. If a sensor is
removed and is to be reinstalled for any reason,
the threads must have anti-seize compound
applied.


Installation Procedure
1. Install the O2 sensor to the exhaust pipe.
Apply anti-seize compound or the equivalent to the
threads of the oxygen sensor, if necessary.
2. Tighten the O2 sensor with specified tightening
torque.
Tightening Torque





Bolt: 42N




m (4.3kgf




m)
3. Connect a sensor connector to the O2 sensor.
4. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.
Verify no exhaust gas leaking from the senso
r
threads after replacement.



EVAP CANISTER PURGE VALVE
SOLENOID

Location
On the intake manifold.

Removal Procedure
1. Disconenct the negative battery cable.
2. Disconnect a purge solenoid connector from the
purge solenoid.
3. Disconnect two hoses from the purge solenoid
valve.
4. Loosen a bolt and remove the purge solenoid from
the intake manifold.






Installation Procedure
1. Put on the purge solenoid on the intake manifold.
2. Tighten the purge solenoid by a bolt.
3. Connect a connector to the purge solenoid.
4. Connect two hoses to the purge solenoid valve.
5. Connect the negative battery cable.

NOTE:
Verify any DTCs (diagnosis Trouble Code) are not
stored after replacement.
Verify proper connection of two hoses.

6F-4 ENGINE EXHAUST (6VE1 3.5L)
Three Way Catalytic Converter and Center Exhaust Pipe
Three Way Catalytic Converter and Center Exhaust Pipe and Associated Parts



RTW46FMF000201
Legend (4) Three Way Catalytic Converter LH
(1) Front Exhaust Pipe Fixing Nuts (5) Mounting Rubber
(2) O
2 Sensor (6) Exhaust Pipe Fixing Nuts
(3) Three Way Catalytic Converter RH (7) Center Exhaust Pipe


Removal
1. Disconnect battery ground cable.
2. Lift up the vehicle and support with suitable safety
stands.
3. Disconnect O
2 sensor harness connectors (2).
4. Remove the center exhaust pipe fixing nuts (6) and
the exhaust silencer fixing bolts, then remove the
center exhaust pipe and the mounting rubber.
5. Remove the front exhaust pipe fixing nuts (1) and
the mounting rubber, then remove the three way
catalytic converter (3) (4).
Installation
1. Install the three way catalytic converter (3) (4) and
the mounting rubber, and tighten the fixing nuts (1)
to the specified torque.
Torque : 67 N




m (6.8 kg




m/49 lb ft)
2. Install the center exhaust pipe and the mounting
rubbler, and tighten the fixing nuts (6) and bolts to
the specified torque.
Torque : 43 N




m (4.4 kg




m/32 lb ft)
3. Connect the O
2 sensor connectors (2).

6J-2 INDUCTION (6VE1 3.5L)
Air Cleaner
Removal
1. Remove positive ventilation hose connector.
2. Remove MAF and IAT sensor.
3. Remove air cleaner duct assembly.
4. Remove air cleaner housing.

P1010024
Inspection
Check the air cleaner filter for damage or dust clogging.
Replace if it is damaged, or clean if it is clogged.
Cleaning Method
Tap the air cleaner filter gently so as not to damage the
paper filter, or clean the element by blowing with
compressed air of about 490 kPa (71 psi) from the
clean side if it is extremely dirty.




130RW002
Installation
1. Install air cleaner housing.
NOTE: The air cleaner filter is not damaged with the
edge to an air cleaner housing.




RTW46JSH000101
2. Attach the mass air cleaner duct cover to the body
completely, then clamp it with the clip.
3. Install MAF and IAT sensor.
4. Install positive crankcase ventilation hose connector.

P1010024