check engine ISUZU TF SERIES 2004 Workshop Manual

6E-248 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
13
Using the DVM and check the CMP sensor ground
circuit.
1. Ignition "On", engine "Off".
2. Disconnect the CMP sensor connector .
3. Check the circuit for short to power supply circuit.
Was the DVM indicated specified value?
E-62
V




Less than 1V
Go to Step 14
Repair faulty
harness and
verify repair
14
Check the shield wire for open or short circuit.
Was the problem found?
- Verify repair Go to Step 15
15
Substitute a known good CMP sensor and recheck.
Was the problem solved?
- Go to Step 16 Go to Step 17
16
Replace the CMP sensor.
Was the problem solved?
- Verify repair Go to Step 17
17
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 18
18
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

6E-250 3.5L ENGINE DRIVEABILITY AND EMISSIONS

Condition For Setting The DTC and Action Taken When The DTC Sets
Flash
Code Code Type DTC Name DTC Setting Condition Fail-Safe (Back Up)
P0351 A Ignition 1 Control
Circuit
P0352 A Ignition 2 Control
Circuit
P0353 A Ignition 3 Control
Circuit
P0354 A Ignition 4 Control
Circuit
P0355 A Ignition 5 Control
Circuit
42
P0356 A Ignition 6 Control
Circuit 1. No DTC relating to CMP sensor and CKP sensor.
2. Engine speed is between 250rpm and 850 rpm.
3. 10 ignition signals are not detected consecutively. Fuel cut is operated more than
2000rpm.

CIRCUIT DESCRIPTION
The Engine Control Module's (ECM) control circuit 1
provides a zero-volt or a 5-volt output signal to the
ignition coil. The normal voltage on the circuit is zero
volts. When the ignition coil receives the 5-volt signal
from the ECM, it provides a ground path for the B+
supply to the primary side of the number 1 ignition coil.
When the ECM shuts off the 5 volts to the ignition coil,
the ignition coil turns “OFF." This causes the ignition coil
primary magnetic field to collapse, producing a voltage
in the secondary coil which fires the spark plug.
The circuit between the ECM and ignition coil is
monitored for an open circuit, short to voltage, and shor
t
to ground. When the ECM detects a problem on ignition
control circuit, it will set a DTC P0351, P0352, P0353,
P0354, P0355 or P0356.

DIAGNOSTIC AIDS
Check for the following conditions:
 Poor connection at ECM – Inspect the harness
connectors for backed-out terminals, imprope
r
mating, broken locks, improperly formed or damaged
terminals, and poor terminal-to-wire connections.
 Damaged harness –Inspect the wiring harness fo
r
damage. If the harness appears to be OK, observe
the Tech 2 display related to DTC P0351 or P0352,
P0353, P0354, P0355 or P0356 while moving the
connector and wiring related to the ignition system.
A
change in the display will indicate the location of the
fault.
Reviewing the Failure Records vehicle mileage since
the diagnostic test last failed may help determine ho
w
often the condition that caused the DTC to be set
occurs. This may assist in diagnosing the condition.

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-251
Diagnostic Trouble Code (DTC) P0351 (Flash Code 42) Ignition 1
Control Circuit
Diagnostic Trouble Code (DTC) P0352 (Flash Code 42) Ignition 2
Control Circuit
Diagnostic Trouble Code (DTC) P0353 (Flash Code 42) Ignition 3
Control Circuit
Diagnostic Trouble Code (DTC) P0354 (Flash Code 42) Ignition 4
Control Circuit
Diagnostic Trouble Code (DTC) P0355 (Flash Code 42) Ignition 5
Control Circuit
Diagnostic Trouble Code (DTC) P0356 (Flash Code 42) Ignition 6
Control Circuit

Step Action Value (s) Yes No
1
Was the "On-Board Diagnostic (OBD) System Check"
performed?
- Go to Step 2 Go to On Board
Diagnostic (OBD)
System Check
2
1. Connect the Tech 2.
2. Review and record the failure information.
3. Select "F0: Read DTC Infor By Priority" in "F0:
Diagnostic Trouble Code".
Is the DTC P0351, P0352, P0353, P0354, P0355 or
P0356 stored as "Present Failure"?
- Go to Step 3 Refer to
Diagnostic Aids
and Go to Step 3
3
1. Using the Tech2, ignition "On" and engine "Off".
2. Select "Clear DTC Information" with the Tech2 and
clear the DTC information.
3. Operate the vehicle and monitor the "F5: Failed
This Ignition" in "F2: DTC Information"
Was the DTC DTC P0351, P0352, P0353, P0354,
P0355 or P0356 stored in this ignition cycle?
- Go to Step 4 Refer to
Diagnostic Aids
and Go to Step 4

6E-252 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
4
Check for poor/faulty connection at the ignition coil or
ECM connector. If a poor/faulty connection is found,
repair as necessary.
Was the problem found?
E-60(A)
E-61(B)
E-53/E-54/E-55/
E-56/E-57/E-58
E-73/E-74











- Verify repair Go to Step 5
5
Visually check the ignition coil for the affected cylinder.
Was the problem found?
- Go to Step 12 Go to Step 6
6
Using the DVM and check the ignition coil signal
circuit for the affected cylinder.
1. Ignition "On", engine "Off".
2. Disconnect the ignition coil connector for the
affected cylinder.
3. Check the circuit for short to battery voltage circuit.
Was the DVM indicated battery voltage?
E-53/E-54/E-55/
E-56/E-57/E-58
V




-
Repair faulty
harness and
verify repair
Go to Step 7

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-253
Step Action Value (s) Yes No
7

Using the DVM and check the ignition coil signal
circuit for the affected cylinder.
Breaker box is available:
1. Ignition "Off", engine "Off".
2. Install the breaker box as type A (ECM
disconnected).
Refer to 6E-95 page.
3. Disconnect the ignition coil connector for the
affected cylinder.
4. Check the circuit for open or short to ground circuit.
Was the problem found?
A32
Breaker Box No.1 Cylinder


E-53





B7
Breaker Box No.2 Cylinder


E-54





A31
Breaker Box No.3 Cylinder


E-55





B8
Breaker Box No.4 Cylinder


E-56





A30
Breaker Box No.5 Cylinder


E-57

6E-254 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No

B9
Breaker Box No.6 cylinder


E-58






Breaker box is not available:
1. Ignition "Off", engine "Off".
2. Disconnect the ignition coil connector for the
affected cylinder and ECM connector.
3. Check the circuit for open or short to ground circuit.
Was the problem found?
E-60(A)
E-53







 No.1 Cylinder

E-60(A)
E-54







No.2 Cylinder

E-60(A)
E-55







 No.3 Cylinder

6E-256 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
8
Using the DVM and check the ignition coil power
supply circuit.
1. Ignition "On", engine "Off".
2. Disconnect the ignition coil connector for the
affected cylinder.
3. Check the circuit for open circuit.
Was the DVM indicated specified value?
E-53/E-54/E-55/
E-56/E-57/E-58
V



10-14.5V
Go to Step 10
Go to Step 9
9
Repair the open or short to ground circuit between the
"IGN. COIL" (15A) and ignition coil for the affected
cylinder.
Is the action complete?
- Verify repair -
10
Using the DVM and check the ignition coil ground
circuit for the affected cylinder.
1. Ignition "On", engine "Off".
2. Disconnect the ignition coil connector for the
affected cylinder.
3. Check the circuit for short to power supply circuit.
Was the DVM indicated specified value?
E-53/E-54/E-55/
E-56/E-57/E-58
V



Less than 1V
Go to Step 11
Repair faulty
harness and
verify repair

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-257
Step Action Value (s) Yes No
11
Using the DVM and check the ignition coil ground
circuit.
1. Ignition "Off", engine "Off".
2. Disconnect the ignition coil connector for the
affected cylinder and ECM connector.
3. Check the circuit for open circuit.
Was the problem found?
E-53/E-54/E-55/
E-56/E-57/E-58




- Repair faulty
harness and
verify repair Go to Step 12
12
Replace the ignition coil for the affected cylinder.
Was the problem solved?
- Verify repair Go to Step 13
13
Is the ECM programmed with the latest software
release?
If not, download the latest software to the ECM using
the "SPS (Service Programming System)".
Was the problem solved?
- Verify repair Go to Step 14
14
Replace the ECM.
Is the action complete?
IMPORTANT: The replacement ECM must be
programmed. Refer to section of the Service
Programming System (SPS) in this manual. Following
ECM programming, the immobilizer system (if
equipped) must be linked to the ECM. Refer to section
11 “Immobilizer System-ECM replacement” for the
ECM/Immobilizer linking procedure.
- Verify repair -

3.5L ENGINE DRIVEABILITY AND EMISSIONS 6E-259
CIRCUIT DESCRIPTION
The engine control module (ECM) monitors the EGR
valve pintle position input to ensure that the valve
responds properly to commands from the PCM, and to
detect a fault if pintle position is differen
t
fromcommanded position.
DIAGNOSTIC AIDS
Check for the following conditions:

Excessive carbon deposit on EGR valve shaf
t
maycause EGR stuck open or unsmooth operation.
Those carbon deposit may occur by unusual
portoperation. Clean up carbon may make
smoothfunction of EGR valve.


Poor connection or damaged harness Inspec
t
thewiring harness for damage. If the harness
appears to be OK, observe the EGR actual position
display on the Tech 2 while moving connectors and
wiring harnesses related to EGR valve. A change in
the display will indicate the location of the fault.

Diagnostic Trouble Code (DTC) P0404 (Flash Code 32) EGR Circuit
Range/Perfomance (Open Valve)
Diagnostic Trouble Code (DTC) P1404 (Flash Code 32) EGR Circuit
Range/Perfomance (Closed Valve)

Step Action Value (s) Yes No
1
Was the "On-Board Diagnostic (OBD) System Check"
performed?
- Go to Step 2 Go to On Board
Diagnostic (OBD)
System Check
2
1. Connect the Tech 2.
2. Review and record the failure information.
3. Select "F0: Read DTC Infor By Priority" in "F0:
Diagnostic Trouble Code".
Is the DTC P0404 or P1404 stored as "Present
Failure"?
- Go to Step 3 Refer to
Diagnostic Aids
and Go to Step 3
3
1. Using the Tech2, ignition "On" and engine "Off".
2. Select "Clear DTC Information" with the Tech2 and
clear the DTC information.
3. Operate the vehicle and monitor the "F5: Failed
This Ignition" in "F2: DTC Information"
Was the DTC P0404 or P1404 stored in this ignition
cycle?
- Go to Step 4 Refer to
Diagnostic Aids
and Go to Step 4

6E-260 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Step Action Value (s) Yes No
4
Check for poor/faulty connection at the EGR valve or
ECM connector. If a poor/faulty connection is found,
repair as necessary.
Was the problem found?
E-60(A)
E-76





- Verify repair Go to Step 5
5
Using the DVM and check the EGR valve.
1. Ignition "Off", engine "Off".
2. Disconnect EGR valve connector.
3. Measure the resistance of EGR valve solenoid coil.
Does the tester indicate standard resistance?
EGR Valve





Apporoximately
8.3 at 20C
Go to Step 6
Go to Step 11
6
Inspect the EGR valve.
1. Remove the EGR valve from the engine.
2. Inspect the EGR valve whether there is any carbon
deposit on shaft.
If excessive carbon deposit is found, clean up the
EGR valve and inspect damage of the pintle and seat.
Was the problem found?
-
Verify repair or
Go to Step 11
Go to Step 7
7
Using the DVM and check the EGR valve solenoid
power supply circuit.
1. Ignition "On", engine "Off".
2. Disconnect the EGR valve connector.
3. Check the circuit for open circuit.
Was the DVM indicated specified value?
E-76
V




10-14.5 V
Go to Step 9
Go to Step 8