mirror ISUZU TF SERIES 2004 Workshop Manual
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2004, Model line: TF SERIES, Model: ISUZU TF SERIES 2004Pages: 4264, PDF Size: 72.63 MB
Page 13 of 4264
ACCESSORIES 9-11
No. Connector face No. Connector face
D-13
Black
Rear speaker -LH H-25
BlackINST Front door -LH
D-17
Black
Rear speaker -RH H-27
BlackINST
Rear body
D-19
White
Remote mirror switch drive side P-1
SilverBattery (+)
D-21
White
Tweeter -RH P-2
SilverRelay
Fuse box
D-22
White
Tweeter -LH P-5
SilverBattery (-)
H-6
White
Engine room
INST P-6
SilverBody earth
H-14
White
Rear body
Rear door -LH P-10
SilverEngine ground
H-16
White
Rear body Rear door -RH R-7
BlackRear speaker -LH
H-18
White
Engine room
INST R-8
BlackRear speaker -RH
H-24
Black
INST
Front door -RH
Page 510 of 4264
10-2 CAB
WINDSHIELD
REMOVAL
RTW4A0LF000901
Removal Steps
1. Interior trim panels (Front side)
/Headlining/Instrument panel assembly
2. Wiper arm assembly
3. Room mirror
4. Side moulding
5. Vent cowl cover
6. Windshield stopper
7. Upper moulding
8. Windshield glass
9. Engine hood rear seal
Page 511 of 4264
CAB 10-3
Important Operations - Removal
3. Room Mirror
Remove the screw and pull the room mirror to upper side.
8. Windshield Glass
Remove the windshield glass, carefully following the steps
listed below:
1) Use a knife to cut through part of the adhesive caulking
material.
2) Secure one end of a piece of steel piano wire (0.02 inches
in diameter) to a piece of wood that can serve as a handle.
3) Use a pair of needle nose pliers to insert the other end o
f
the piano wire through the adhesive caulking material at the
edge of the windshield glass.
4) Secure the other end of the piano wire to another piece o
f
wood.
5) With the aid of an assistant, carefully move the piano wire
with a sawing motion to cut through the adhesive caulking
material around the entire circumference of the windshield
glass.
6) Lift the windshield from the body.
7) Clean any remaining adhesive caulking material from the
area of the body which holds the windshield.
8) Use a soft rag and unleaded gasoline to wipe off an
y
adhesive remaining on the windshield glass.
Page 512 of 4264
10-4 CAB
INSTALLATION
RTW4A0LF001201
Installation Steps
1. Engine hood rear seal
2. Upper moulding
3. Windshield glass
4. Windshield stopper
5. Vent cowl cover
6. Side moulding
7. Room mirror
8. Wiper arm assembly
9. Interior trim panels (Front side)
/Headlining/Instrument panel assembly
Page 520 of 4264
10-12 CAB
DISASSEMBLY
This illustration is based on RHD model
RTW4A0LF000701
Disassembly Steps
1. Switch bezel/Window regulator handle
2. Power window switch
3. Bezel
4. Door mirror cover
5. Door trim panel
6. Tweeter (Required Option)
7. Door mirror assembly
8. Outer waste seal
9. Bracket
10. Speaker assembly
11. Waterproof sheet
12. Inside lever
13. Window glass
14. Window regulator/Power window
regulator
15. Glass run
16. Glass run rear channel / Glass ran rear
channel with Door lock control or Anti
theft (EC)
17. Door lock assembly/Door lock assembly
with super lock
18. Outside handle protector (EUROPE)
19. Outside handle
20. Door lock cylinder protector (EUROPE)
21. Door lock cylinder / Door lock cylinder
with door lock switch (EC)
22. Door harness assembly
23. Anti rattler
Page 521 of 4264
CAB 10-13
Important Operations
1. Switch Bezel/Window Regulator Handle
Remove the 2 screws and disconnect the connectors.
To remove the regulator handle, remove the clip at the
root of the handle by using wire.
2. Power Window Switch
Remove the 3 screws.
3. Bezel
Remove the screw.
4. Door Mirror Cover
Pull out the upper clip, and then take out the cove
r
upward.
5. Door Trim Panel
Pull out the trim panel at the 8 clip positions (Powe
r
window type).
Page 522 of 4264
10-14 CAB
Remove the 2 screws and pull out the trim panel at the 8
clip positions (Window regulator handle type).
RTW3A0SH000701
6. Tweeter (Required option)
Disconnect the tweeter harness connector and remove
the 3 screws.
7. Door Mirror Assembly
Remove 3 fixing bolts and then remove the connector.
8. Outer Waste Seal
9. Bracket
10. Speaker Assembly
Remove the fixing screw and then remove the
connector.
11. Waterproof Sheet
Take care not to damage the sheet when peeling it off.
12. Inside Lever
Disconnect the door lock cables.
Page 524 of 4264
10-16 CAB
REASSEMBLY
This illustration is based on RHD model
RTW4A0LF000801
Reassembly Steps
1. Anti rattler
2. Door harness assembly
3. Door lock cylinder / Door lock cylinder
with door lock switch (EC)
4. Door lock cylinder protector (EUROPE)
5. Outside handle
6. Outside handle protector (EUROPE)
7. Door lock assembly / Door lock
assembly with super lock
8. Glass run rear channel / Glass ran rear channel with Door lock control or Anti
theft (EC)
9. Glass run
10. Window regulator / Power window
regulator
11. Window glass
12. Inside lever
13. Waterproof sheet
14. Speaker assembly
15. Bracket
16. Outer waste seal
17. Door mirror assembly
18. Tweeter (Required option)
19. Door trim panel
20. Door mirror cover
21. Bezel
22. Power window switch
23. Switch bezel / Window regulator handle
Page 661 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-3
PAGE
Power Window ........................................................................................................... 8A- 310
Audio, Clock and Cigarette Lighter .......................................................................... 8A- 329
Power Door Mirror ...................................................................................................... 8A- 337
Rear Defogger ............................................................................................................ 8A- 349
SRS-Air Bag ................................................................................................................ 8A- 358
Transfer Case Control Module .................................................................................. 8A- 361
Anti-Lock Brake System ............................................................................................ 8A- 373
Immobilizer ................................................................................................................. 8A- 376
Keyless Entry ............................................................................................................. 8A- 385
Anti Theft ....................................................................................................................8A- 400
Auto Cruise ................................................................................................................. 8A- 412
Trailer Hitch ................................................................................................................ 8A- 415
Connector List ................................................................................................................8A- 418
Page 995 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-337
POWER DOOR MIRROR
PARTS LOCATION (RHD)
RTW48AXF020401 & RTW48AXF020501