oil pressure ISUZU TF SERIES 2004 Workshop Manual

ISUZU TF SERIES 2004 Workshop Manual TF SERIES 2004 ISUZU ISUZU https://www.carmanualsonline.info/img/61/57180/w960_57180-0.png ISUZU TF SERIES 2004 Workshop Manual

Page 190 of 4264

ISUZU TF SERIES 2004  Workshop Manual 4B-26  REAR AXLE
 
4.  Place the shim on the drive pinion, then install the
inner bearing onto the pinion by using installer 9-
8522-1165-0 and a press. 
Note: 
Do not apply pressure to the roller cag

Page 202 of 4264

ISUZU TF SERIES 2004  Workshop Manual 4B-38  REAR AXLE
 
Inspection and Repair 
Make all necessary adjustments, repairs, and part 
replacements if wear, damage, rust or other problems 
are discovered during inspection. 
 
Visual Check 
In

Page 205 of 4264

ISUZU TF SERIES 2004  Workshop Manual REAR AXLE  4B-41
 
 
 
425RS066
 
2.  Measuring dimension between thrust washers at 
both ends. 
  Assemble side gear, pinion, pinion shaft pressure 
ring and thrust washer. 
   Eliminate clearance b

Page 257 of 4264

ISUZU TF SERIES 2004  Workshop Manual FRONT WHEEL DRIVE  4C1-37 
(7) Select the shim using the chart; 
 
 mm(i n) 
 Pi ni on 
 marki ng 
 
+10 +8 +6 +4 +2  0  -2  -4  -6  -8 -10 Dial indicator 
reading (inches)            
0.081

Page 325 of 4264

ISUZU TF SERIES 2004  Workshop Manual BRAKE CONTROL SYSTEM   5A-9
 
Pressure Isolation (Pressure Maintain) 
The electronic-hydraulic control unit is activated when 
the brakes are applied. 
If the information from the wheel speed sensors

Page 449 of 4264

ISUZU TF SERIES 2004  Workshop Manual BRAKES  5C-23
 
 RTW35CSH001301 
 
 4)  Failure on front master cylinder. 
  In case of failure on front master cylinder the pressure on 
the inlet port (C) drop to zero. The pressure from inlet por
t

Page 450 of 4264

ISUZU TF SERIES 2004  Workshop Manual 5C-24  BRAKES
 
 RTW35CSH000201 
3)  Rear wheel cylinder fluid pressure measurement 
  Step on the brake pedal until the fluid pressure of the 
front wheel cylinder gets to 9.8Mpa (100kg/cm
2), and 
c

Page 451 of 4264

ISUZU TF SERIES 2004  Workshop Manual BRAKES  5C-25
 
  
Filling Master Cylinder Reservoir 
CAUTION :  
Use only specified brake fluid.  Do not use any fluid which 
contains a petroleum base.  Do not use a container which 
has been used f

Page 646 of 4264

ISUZU TF SERIES 2004  Workshop Manual 7C-44  CLUTCH
 
Checkpoint  Trouble Cause  Countermeasure 
 
Replace the release bearingRelease bearing broken
Clean the related parts and/or
replace the facing
Replace the crankshaft rear oil
seal
De

Page 649 of 4264

ISUZU TF SERIES 2004  Workshop Manual CLUTCH  7C-47
 
3.  CLUTCH SHUDDER 
 
Checkpoint 
 Trouble Cause 
 Countermeasure 
 
Grease or oil adhering to the
facing
Clean the related parts and/or
replace the facing
Replace the transmission fro
Page:   1-10 11-20 21-30 31-40 41-50 ... 220 next >