relay ISUZU TF SERIES 2004 Workshop Manual

9-10 ACCESSORIES

CONNECTOR LIST
No. Connector face No. Connector face
B-10
White
Clock B-56
WhiteJ/B I4
B-14
Gray
Audio B-62
WhiteIgnition switch
B-20
White
Cigar lighter illumination B-64
SilverWeld splice 1
B-21
White
Cigar lighter B-65
SilverWeld splice 2
B-22
Black
Cigar lighter B-73
SilverWeld splice 3
B-40
Black
Acc socket relay C-2
BlackEngine room –RH ground
B-41
Natural
Acc socket C-108
White
J/B E1
B-42
White
Acc socket C-109
BlackBody –LH ground
B-43

Anti theft control unit D-3
BlackFront speaker -RH
B-55
White
J/B I3 D-8
BlackFront speaker -LH

ACCESSORIES 9-11


No. Connector face No. Connector face
D-13
Black
Rear speaker -LH H-25
BlackINST
Front door -LH
D-17
Black
Rear speaker -RH H-27
BlackINST

Rear body
D-19
White
Remote mirror switch drive side P-1
SilverBattery (+)
D-21
White
Tweeter -RH P-2
SilverRelay 
Fuse box
D-22
White
Tweeter -LH P-5
SilverBattery (-)
H-6
White
Engine room

INST P-6
SilverBody earth
H-14
White
Rear body

Rear door -LH P-10
SilverEngine ground
H-16
White
Rear body
Rear door -RH R-7
BlackRear speaker -LH
H-18
White
Engine room

INST R-8
BlackRear speaker -RH
H-24
Black
INST

Front door -RH

BRAKE CONTROL SYSTEM 5A-3

DTC C0235 (Flash Code 35) Rear Left Wheel Speed Sensor Short Circuit or
Circuit Open .................................................................................................................... 5A-62
DTC C0236 (Flash Code 36) Rear Left Wheel Speed Sensor Incorrect Signal ............. 5A-64
DTC C0237 (Flash Code 37) Rear Left Wheel Speed Sensor Signal - Tooth
Chipping ........................................................................................................................... 5A-66
DTC C0238 (Flash Code 38) Tire Diameter Error ............................................................. 5A-68
DTC C0241 (Flash Code 41) Front Right Isolation Solenoid Circuit Open or
Shorted to Ground ........................................................................................................... 5A-69
DTC C0242 (Flash Code 42) Front Right Dump Solenoid Circuit Open or Shorted
to Ground.......................................................................................................................... 5A-69
DTC C0243 (Flash Code 43) Front Right Isolation Solenoid Circuit Shorted to
Battery............................................................................................................................... 5A-69
DTC C0244 (Flash Code 44) Front Right Dump Solenoid Circuit Shorted to
Battery............................................................................................................................... 5A-69
DTC C0245 (Flash Code 45) Front Left Isolation Solenoid Circuit Open or
Shorted to Ground ........................................................................................................... 5A-71
DTC C0246 (Flash Code 46) Front Left Dump Solenoid Circuit Open or Shorted
to Ground.......................................................................................................................... 5A-71
DTC C0247 (Flash Code 47) Front Left Isolation Solenoid Circuit Shorted to
Battery............................................................................................................................... 5A-71
DTC C0248 (Flash Code 48) Front Left Dump Solenoid Circuit Shorted to
Battery............................................................................................................................... 5A-71
DTC C0251 (Flash Code 51) Rear Isolation Solenoid Circuit Open or Shorted to
Ground .............................................................................................................................. 5A-73
DTC C0252 (Flash Code 52) Rear Dump Solenoid Circuit Open or Shorted to
Ground .............................................................................................................................. 5A-73
DTC C0253 (Flash Code 53) Rear Isolation Solenoid Circuit Shorted to Battery ......... 5A-73
DTC C0254 (Flash Code 54) Rear Dump Solenoid Circuit Shorted to Battery .............. 5A-73
DTC C0265 (Flash Code 65) Fail Safe Relay (FSR) Shorted to Ground ......................... 5A-75
DTC C0266 (Flash Code 66) Fail Safe Relay (FSR) Shorted to Battery.......................... 5A-75
DTC C0267 (Flash Code 67) ABS Motor Shorted to Ground .......................................... 5A-77
DTC C0268 (Flash Code 68) ABS Motor Shorted to Battery ........................................... 5A-77
DTC C0271 (Flash Code 71) ECU Failure or Valve +B Circuit Open .............................. 5A-79
DTC C0274 (Flash Code 74) ABS Operation Long Time ................................................. 5A-80
DTC C0276 (Flash Code 76) G-Sensor Malfunction ........................................................ 5A-82

5A-14 BRAKE CONTROL SYSTEM


No. Connector face No. Connector face
H-15
White
Engine Room ~ Chassis


H-18
White
Engine Room ~ INST


P-2
Silver
Relay & Fuse Box


P-6
Silver
Body Earth (Ground)


P-10
Silver
Engine Ground


R-15
Black
2-4WD Control Unit

BRAKE CONTROL SYSTEM 5A-19

System Components
Electronic Hydraulic Control Unit (EHCU), four Wheel
Speed Sensors, two Warning Lamps, and G-sensor.

Electronic Hydraulic Control Unit (EHCU)

The EHCU consists of ABS control circuits, fault
detector, and a fail-safe. It drives the EHCU according
to the signal from each sensor, cancelling ABS to return
to normal braking when a malfunction has occurred in
the ABS.
The EHCU has a self-diagnosing function which can
indicate faulty circuits during diagnosis.
The EHCU is mounted on the engine compartment rear
left side. It consists of a motor, solenoid valves fail safe
relay.
Solenoid Valves: Reduces or holds the caliper fluid
pressure for each front brake or both rear brakes
according to the signal sent from the EHCU.
Buffer chamber: Temporarily holds the brake fluid that
returns from the front and rear brake so that pressure
of front brake can be reduced smoothly.
Motor: Drives the pump according to the signal from
EHCU.
Fail safe Relay: When failure occurs in ABS.
The power supply to solenoid Valve is cut.

ABS Warning Lamp


825L300001
Vehicles equipped with the Anti-lock Brake System
have an amber “ABS” warning lamp in the instrument
panel. The “ABS” warning lamp will illuminate if a
malfunction in the Anti-lock Brake System is detected
by the Electronic Hydraulic Control Unit (EHCU). In
case of an electronic malfunction, the EHCU will turn
“ON” the “ABS” warning lamp and disable the anti-lock
braking function.

The “ABS” warning lamp will turn “ON” for
approximately three seconds after the ignition switch is
to the “ON” position.
If the “ABS” warning lamp stays “ON” after the ignition
switch is the “ON” position, or comes “ON” and stays
“ON” while driving, the Anti-lock Brake System should
be inspected for a malfunction according to the
diagnosis procedure.

Wheel Speed Sensor (WSS)
It consists of a sensor and a rotor. The sensor is
attached to the knuckle on the front wheels and to the
rear wheels.
The rotor is press-fit in the axle shaft.

G-Sensor
The G-sensor detects the vehicle deceleration speed
and sends a signal to the EHCU. In 4WD operation, all
four wheels may be decelerated in almost the same
phase, since all wheels are connected mechanically.
This tendency is noticeable particularly on roads with
low friction coefficient, and the ABS control is adversely
affected.
The G-sensor judges whether the friction coefficient of
road surface is low or high, and changes the EHCU's
operating system to ensure ABS and EBD control.

Normal and Anti-lock Braking
Under normal driving conditions, the Anti-lock Brake
System functions the same as a standard power
assisted brake system. However, with the detection of
wheel lock-up, a slight bump or kick-back will be felt in
the brake pedal. This pedal “bump” will be followed by a
series of short pedal pulsations which occurs in rapid
succession. The brake pedal pulsation will continue
until there is no longer a need for the anti-lock function
or until the vehicle is stopped. A slight ticking or
popping noise may be heard during brake applications
when the anti-lock features is being used.
When the anti-lock feature is being used, the brake
pedal may rise even as the brakes are being applied.
This is also normal. Maintaining a constant force on
the pedal will provide the shortest stopping distance.

5A-26 BRAKE CONTROL SYSTEM

DATA LIST (Tech 2)
The data displayed by DATA LIST are as follows:


Strings Units Description 2WD 4WD
Front Left Wheel Speed km/h (MPH)
Front Right Wheel Speed km/h (MPH)
Rear Left Wheel Speed km/h (MPH)
Rear Right Wheel Speed km/h (MPH) Start the vehicle and make sure of linear
change in each wheel speed
Brake Switch Open/Closed Brake switch is “closed” when brake pedal is
stepped on.
ABS Warning Lamp On/Off To be “Off” usually
EBD Warning Lamp On/Off To be “Off” usually
ABS Stop State On/Off To be “Off” usually
ABS Relay Active/Inactive To be “Active” usually
Return Pump Active/Inactive To be “Inactive” usually
DTC Status No DTC To be “No DTC” usually
4 Wheel Drive Status Yes/No To be “Yes” usually
-
FL Dump Valve Commanded
(Front Left) Active/Inactive
FL Isolation Valve Commanded
(Front Left) Active/Inactive
FR Dump Valve Commanded
(Front Right) Active/Inactive
FR Isolation Valve Commanded
(Front Right) Active/Inactive
Rear Dump Valve Commanded Active/Inactive
Rear Isolation Valve Commanded Active/Inactive
FL Dump Valve Feedback
(Front Left) Active/Inactive
FL Isolation Valve Feedback
(Front Left) Active/Inactive
FR Dump Valve Feedback
(Front Right) Active/Inactive
FR Isolation Valve Feedback
(Front Right) Active/Inactive
Rear Dump Valve Feedback Active/Inactive
Rear Isolation Valve Feedback Active/InactiveEach valve is “Active” when each valve is
opereted.
G-Sensor Output V 2.0~3.0V when vehicle speed is 0 km/h (flat
place) -
Battery Voltage V The voltage value currently supplied to EHCU
Diagnostics Connector Open/Closed Diagnostics connector is “Open” when
diagnostics connector is connected.

BRAKE CONTROL SYSTEM 5A-27

Actuator Test (Tech 2)
There are 5 different menus available for this test. The
state of each circuit can be tested by using these
menus. Especially when DTC cannot be detected, a
faulty circuit can be diagnosed by testing each circuit by
means of these menus.
Even when DTC has been detected, the circuit tests
using these menus could help discriminate between a
mechanical trouble and an electrical trouble.
In all cases test condition; Engine stops with the key
turned to the “ON” position. To be more specific, the
test is conducted with the brake pedal stepped on after
stepping once and releasing.
 Engine: Stop
 Ignition SW: ON

060L300002

ABS Check Light Test
Test condition: Engine stops with the key turned to the
“ON” position. To be more specific, the test is
conducted with the brake pedal stepped on after
stepping once and releasing.
 The circuit is normal if the warning light (lamp) in
the meter panel comes on and goes out in
accordance with Tech2’s instruction.

060L300002

Return Pump Test
Test condition: Engine stops with the key turned to the
“ON” position. To be more specific, the test is
conducted with the brake pedal stepped on after
stepping once and releasing.
Make sure of the working sound of the return pump
relay and return pump.
The circuit is normal if the working sound of the return
pump relay and return pump are made in accordance
with Tech2’s instruction.

060L300002

BRAKE CONTROL SYSTEM 5A-31

Warning Lamp System Control Main Items DTC
(Flash
Code) Description
ABS Brake
(EBD)ABS EBD
C0248
(48) Front Left Dump Solenoid Circuit
Shorted to Battery



Solenoid (EHCU)
C0251
(51) Rear Isolation Solenoid Circuit Open or
Shorted to Ground



Solenoid (EHCU)
C0252
(52) Rear Dump Solenoid Circuit Open or
Shorted to Ground



Solenoid (EHCU)
C0253
(53) Rear Isolation Solenoid Circuit Shorted
to Battery



Solenoid (EHCU)
C0254
(54) Rear Dump Solenoid Circuit Shorted to
Battery



Solenoid (EHCU)
C0265
(65) Fail Safe Relay (FSR) Shorted to
Ground



Motor (EHCU)
C0266
(66) Fail Safe Relay (FSR) Shorted to
Battery



Relay (EHCU)
C0267
(67) ABS Motor Shorted to Ground



Motor (EHCU)
C0268
(68) ABS Motor Shorted to Battery



Motor (EHCU)
C0271
(71) ECU Failure or Valve +B Circuit Open



EHCU
C0274
(74) ABS Operation Long Time



EHCU

C0276
(76) G-Sensor Malfunction



Sensor or Wiring




Battery, Wiring or EHCU
(less than 9V) C0277
(77) Power Supply Low Input




Battery or Wiring
(less than 10V)
C0278
(78) Power Supply High Input



Battery or Wiring EHCU
C0282
(82) 4 Wheel Drive State Input Signal Failure



Wiring
C0285
(85) Assembly Error (G-sensor)



Vehicle (Sensor or EHCU)

*A : When three or more failure are detected, or when
failure containing both front wheels and each rear
wheels are detected, EBD warning lamp is "ON"
and control is canceled.
*B : ABS lamp is “OFF” when the ABS lamp is “ON”
after a repair until vehicles speed becomes more
than 6km/h (4mph) in the following ignition cycle
and failure is not detected.

BRAKE CONTROL SYSTEM 5A-75

DTC C0265 (Flash Code 65) Fail Safe Relay (FSR) Shorted to Ground
DTC C0266 (Flash Code 66) Fail Safe Relay (FSR) Shorted to Battery



RTW45AMF000201

Step Action
Value(s) Yes No
1 Was the “Basic Diagnostic Flow Chart” performed?
- Go to Step 2 Go to Basic
Diagnostic
Flow Chart
2 1. Ignition “OFF”.
2. Check the EHCU circuit for an open, short to
ground, or short to voltage. Also, check the EHCU
ignition feed circuit for an open or short to ground
and the EHCU ground circuit for an open or short to
voltage.
3. If a problem is found, repair as necessary.
Was a problem found?
- Verify repair Go to Step 3
3 1. Ignition “ON,” engine “OFF.”
2. Select “Display DTCs” with the Tech 2.
Note: Perform the various tests (actuator test, test
run, brake test, etc.) then observe the DTC with a
Tech2.
Are any DTCs stored? - Go to Step 4 Verify repair

ELECTRICAL-BODY AND CHASSIS 8A-1
SECTION 8A
ELECTRICAL-BODY AND CHASSIS
TABLE OF CONTENTS
PAGE
General Information ........................................................................................................ 8A- 4
Notes for Working on Electrical Items .......................................................................... 8A- 5
Symbols and Abbreviations ........................................................................................... 8A- 11
Symbols ...................................................................................................................... 8A- 11
Abbreviations ............................................................................................................. 8A- 12
Parts for Electrical Circuit .............................................................................................. 8A- 13
Wiring .......................................................................................................................... 8A- 13
Fuse ............................................................................................................................. 8A- 15
Fusible Link ................................................................................................................ 8A- 15
Relay ............................................................................................................................ 8A- 16
Diode ........................................................................................................................... 8A- 17
Connector ................................................................................................................... 8A- 18
Battery ......................................................................................................................... 8A- 19
Reading the Circuit Diagram .......................................................................................... 8A- 22
Parts Location ............................................................................................................ 8A- 22
Circuit Diagram ........................................................................................................... 8A- 23
Connector List ............................................................................................................. 8A- 23
Main Data and Specifications ........................................................................................ 8A- 24
Bulb Specifications .................................................................................................... 8A- 24
Relay and Fuse ................................................................................................................ 8A- 26
Relay and Fuse Box Location ................................................................................... 8A- 26
Relay Location ............................................................................................................ 8A- 28