center console ISUZU TF SERIES 2004 Workshop Manual

[x] Cancel search | Manufacturer: ISUZU, Model Year: 2004, Model line: TF SERIES, Model: ISUZU TF SERIES 2004
Pages: 4264, PDF Size: 72.63 MB

Page 495 of 4264

ISUZU TF SERIES 2004 Workshop Manual PARKING BRAKE SYSTEM 5D-5

Front Parking Brake Cable
Front Parking Brake Cable and Associated Parts (Bench Seat)

750R300003

Legend

(1)
Shift Knob (manual transmission)

(2)
Front

Page 536 of 4264

ISUZU TF SERIES 2004 Workshop Manual 10-28 CAB
INSTRUMENT PANEL
REMOVAL

This illustration is based on RHD model
RTW4A0LF001001

Disassembly Steps
1. Front console assembly
2. Glove box
3. Instrument pa

Page 540 of 4264

ISUZU TF SERIES 2004 Workshop Manual 10-32 CAB
INSTALLATION

This illustration is based on RHD model
RTW4A0LF001101

Installation Steps
1. Cross beam
2. Instrument panel
3. Instrument harness assembly
4. Vent

Page 2516 of 4264

ISUZU TF SERIES 2004 Workshop Manual 6B-6 ENGINE COOLING

Draining and Refilling Cooling
System
Before draining the cooling system, inspect the system and
perform any necessary service to ensure tha

6B-6 ENGINE COOLING

Draining and Refilling Cooling
System
Before draining the cooling system, inspect the system and
perform any necessary service to ensure that it is clean, does
not leak and is in proper working order. The engine coolant
(EC) level should be between the "MIN" and "MAX" lines of
reserve tank when the engine is cold. If low, check for leakage
and add EC up to the "MAX" line. There should not be any
excessive deposit of rust or scales around the radiator cap or
radiator filler hole, and the EC should also be free from oil.
Replace the EC if excessively dirty.
1. Completely drain the cooling system by opening the drain
plug at the bottom of the radiator.
2. Remove the radiator cap.
WARNING: TO AVOID THE DANGER OF BEING BURNED,
DO NOT REMOVE THE CAP WHILE THE ENGINE AND
RADIATOR ARE STILL HOT. SCALDING FLUID AND
STEAM CAN BE BLOWN OUT UNDER PRESSURE.
3. Disconnect all hoses from the EC reserve tank.
Scrub and clean the inside of the reserve tank with soap
and water. Flush it well with clean water, then drain it. Install
the reserve tank and hoses.
4. Refill the cooling system with the EC using a solution that is
at least 50 percent antifreeze.
5. Fill the radiator to the base of the filler neck.
Fill the EC reserve tank to "MAX" line when the engine is
cold.
6. Block the drive wheels and firmly apply the parking brake.
Shift an automatic transmission to "P" (Park) or a manual
transmission to neutral.
7. Remove the radiator cap. Start the engine and warm it up a
t
2,500 - 3,000 rpm for about 30 minutes.
8. When the air comes out from the radiator filler neck and the
EC level has gone down, replenish with the EC. Repeat this
procedure until the EC level does not go down. Then stop
the engine and install the radiator cap. Let the engine cool
down.
9. After the engine has cooled, replenish with EC up to the
"MAX" line of the reserve tank.
10. Start the engine. With the engine running at 3,000 rpm,
make sure there is no running water sound from the heate
r
core (behind the center console).
11. If the running water sound is heard, repeat steps 8 to 10.

Page 3079 of 4264

ISUZU TF SERIES 2004 Workshop Manual HEATER AND AIR CONDITIONING 1-69
REAR HEATER DUCT
REMOVAL AND INSTALLATION

This illustration is based on RHD model
RTW410LF001301

Disassembly Steps
1. Front seat assembly (RH/LH)

Page 3181 of 4264

ISUZU TF SERIES 2004 Workshop Manual MANUAL TRANSMISSION 7B1-17

14. Install the exhaust pipe (8). (6VE1)
Torque: 67 N
m (6.8 kg
m/49 lb
ft)
RTW37ASH000101
15. Install rear propeller shaft (6).
Torque: 63 N