fuel JAGUAR S TYPE 1999 1.G Powertrain Manual

V6 EngineAJ-V6/AJ28
43 Intake Air Temperature (IAT) Sensor
The IAT sensor is a conventional thermistor type
device which is a push fit in the intake resonator
duct.
Mass Air Flow (MAF) Sensor
The MAF sensor is an integral assembly consisting
of a hot wire sensor unit and air duct and is non-
serviceable. The assembly is fitted between the air
cleaner and intake resonator tube.
D.303.1381
MAF AND IAT SENSORS
D.303-1381
J.303.1386
HO2 SENSORS
J.303-1386
Heated Oxygen (HO2) Sensors
HO2 sensors are fitted in both the upstream and
downstream positions on the catalytic converters.
Both sensors are standard types with a step
response at the stoichiometric (lambda) air/fuel
value. The upstream sensors provide the feedback
for stoichiometric fuelling control and the
downstream sensors monitor catalyst efficiency
and also provide long term fuelling adaptation
trim.
MAF SensorIAT Sensor

V8 EngineAJ-V6/AJ28
45
Introduction
The AJ28 engine is a variant of the 4.0L 90û V8 units fitted to the XJ and XK range of vehicles. The AJ28
shares some of the changes incorporated in the current AJ27 engine: both engines are derived from the
original AJ26 unit. A number of features are unique to the AJ28 or are shared with the AJ-V6 engine also
described in this publication.
Features of the AJ28 engine are:
¥ Continuously variable inlet valve timing over a 48û
+
-2û crank angle: as fitted to the AJ27 engine
¥ Full authority cable-less electronic throttle control: as fitted to the AJ-V6 engine
¥ Air assisted fuel injection: similar to system used on the AJ27 engine
¥ Unique induction manifold with centrally mounted throttle body
¥ Returnless fuel system: similar to AJ-V6 engine
¥ Twin wall exhaust manifold
¥ Engine management system as used on the AJ-V6
¥ New sensors
¥ Modified sump and oil cooler
¥ Modified front end ancillary drive and components
Engine Specification
Maximum power DIN - 209 kW (281 BHP) at 6100 RPM
EEC - 203 kW (276 PS) at 6100 RPM
Maximum torque DIN - 390 Nm (287 lbft) at 4300 RPM
EEC - 278 Nm (279 lbft) at 4300 RPM
Oil Specification
All markets except the USA and Canada
Engine oil for all markets except the USA and
Canada must be to API specification SJ/ACEA A1
or A3.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 1.
USA/Canada
Engine oil for USA and Canada must be to API
specification SJ/ILSAC GF-2.
The recommended SAE viscosity for different
ranges of ambient temperature are shown in
table 2. For maximum economy and in most
climate conditions, SAE 5W/30 is to be preferred
but SAE 10W/30 or 15W/40 are acceptable in
moderate to hot climates.
JOL.29550
50JOL.296
SAE/TEMPERATURE TABLE 2
SAE/TEMPERATURE TABLE 1

V8 EngineAJ-V6/AJ28
51
Air Induction System
Charge air is supplied to the cylinders via an air
cleaner, induction tube, throttle body, throttle
body adaptor and induction manifold.
The throttle body and system operation is
identical to that of the V6 engine.
Induction Manifold
(see illustration on page 52)
To accommodate the V8 engine in the S-TYPE
model, the throttle body is re-located and now
supplies charge air via an inlet at the top centre of
the induction manifold. The manifold is
manufactured from a plastic material and has an
integral injector air supply tube on each side with
holes for the fuel injectors, but as on the AJ27
engine, the fuel feed pipes are not incorporated
into the manifold (see Fuel System). Two stub
pipes at the top of the manifold provide vacuum
connections for the vacuum hose and the brake
servo hose.
A polypropylene covered foam noise isolation pad
fits between the manifold assembly and the block.Throttle Adaptor
The throttle body is mounted to the induction
manifold via a cast aluminium adaptor. The
throttle body adaptor provides input ports for the
evaporative emissions (top stub) and part load
breather (lower side stub) and also mounts the air
assisted injection control (AAC) valve. Input and
output ports for the side mounted AAC valve are
an integral part of the adaptor casting (the ports
do not connect to the induction airstream).
Throttle de-icing is achieved by a coolant feed
through the base of the adaptor instead of the
throttle body itself as on the V6 engine (see
cooling section).
D.303.1278
AIR INDUCTION LAYOUT
D.303.1278
Air Cleaner
Induction Tube
MAF SensorIAT Sensor
Throttle Body
Throttle Body Adaptor

V8 Engine AJ-V6/AJ28
54
Engine Management Sensors
The configuration of the AJ28 engine management sensors is changed from the previous V8 variants:
¥ New components unique to AJ28 engine are the MAF sensor and engine fuel temperature (EFT)
sensor.
¥ Components in common with the V6 engine are the IAT sensor, KS sensors, injector pressure (IP)
sensor, engine oil temperature (EOT) sensor and HO2 sensors.
¥ The crankshaft (CKP) and camshaft (CMP) sensors are the same as those fitted to the AJ27 engine.
Heated Oxygen (HO2) Sensors
Upstream and dowmstream HO2 sensors are
fitted and are of the type used on the V6 engine
(the linear type sensor is not used).
J.303.1387
HO2 SENSORS
J.303.1387
J.303.1281
COIL ON PLUG UNIT
J.303.1281
Ignition System
The coil-on-plug ignition modules are specific to
the AJ28 engine and are triggered directly from
the PCM. Double electrode platinum plugs are
fitted.

V8 EngineAJ-V6/AJ28
55
J.303.1389
ENGINE MANAGEMENT SCHEMATIC
13
2
45
6
8
157
9
1110
13
16
J.303-1287
9
10
12
14
Key :
1. MAF sensor
2. IAT sensor
3. TP sensor
4. Throttle motor
5. AAC valve
6. IP sensor8
11
16
1616
7. EFT sensor
8. Fuel injectors
9. CMP sensor
10. Coil-on-plug units
11. VVT shuttle valve
12. ECT sensor13. KS sensors
14. CKP sensor
15. EOT sensor
16. HO2 sensors

V8 Engine AJ-V6/AJ28
56
Fuel Injection
Returnless Fuel System
The function and operation of the returnless fuel
system is the same as that fitted to the V6 engine
but with different fuel pipework to suit the V8
layout. The air assisted, top fed, fuel injectors are
supplied from two separate rails joined by an
interconnecting cross-over pipe (similar to AJ27)
with a single common feed from the fuel tank.
The fuel rail assembly is removeable. An engine
fuel temperature (EFT) sensor and injector
pressure (IP) sensor provide feedback to the PCM
to control the fuel pump flow rate (see ÔS-TYPE
IntroductionÕ Technical Guide). Note that the EFT
sensor is not in direct contact with the fuel (ÔdryÕ
type sonser).
J.303.1390
FUEL RAIL ASSEMBLY
IP Sensor
EFT Sensor
J.303.1390

V8 EngineAJ-V6/AJ28
57
Air Assisted Injection
The air assisted injection system is very similar to
the AJ27 system, with a solenoid valve controlling
an air supply to the fuel injector nozzles. The AJ28
engine uses a different type of injector and air
assist control AAC valve. The AAC valve bolts to
the side of the throttle adaptor which provides an
inlet port connection from the intake resonator
duct via a hose and an outlet port to the air rails.
The injectors are located in the air rails which are
integral with the manifold.
J.303.1257
AAC VALVE AND AIR DISTRIBUTION
J.303.1257
J.303.1392
AAC VALVE
J.303-1392
Valve shown in the closed,
de-energised state
InletOutlet
AAC Valve

V8 Engine AJ-V6/AJ28
58FUEL INJECTOR
303-135
Fuel Injectors
The type of fuel injector used operates in a similar
way to the type fitted to the AJ27 engine but has a
different shroud arrangement at the nozzle to
provide the air/fuel mixing.
Fuel Supply
Assisted
Air Inlet

Powertrain ManagementAJ-V6/AJ28
69
Introduction
All powertrain and associated management
functions are controlled from a single unit, the
powertrain control module (PCM). These
functions are as follows:
¥ overall monitoring and control of
performance, fuel economy, emissions,
driveability and safety
¥ receives and processes direct inputs from
engine, transmission, fuel system and
ancillary systems sensors
¥ provides direct control of actuator devices
¥ communicates with other modules via the
SCP bus (eg to obtain wheel speed
information)
¥ provides system diagnostics to conform to
OBDII requirements.
Powertrain Control Module (PCM)
The basic PCM is common to the V6 and V8
engines but with unique programming to suit the
respective engine characteristics and some
differences in the interface circuits for the
different sensors and actuators.
The PCM is located below the LH or RH mounted
A/C evaporator/blower unit and has a single
connector panel which protrudes through the
forward bulkhead into the engine bay.
The PCM has three connectors:
¥ a 60 pin connector which provides the
interfacing with the engine wiring harness:
carries engine mounted sensor inputs and
output control signals
¥ a 32 pin connector which carries the
transmission sensing and control signals and
also the rear HO2 sensor inputs
¥ a 58 pin connector which carries non engine
mounted sensor and actuator signals and
provides the PCM link to the SCP bus.
Powertrain Sub-Systems
Brief descriptions of PCM control of new
subsystems are given in the relevant engine and
transmission sections (electronic throttle,
returnless fuel etc).
J.303.1393
POWERTRAIN CONTROL MODULE
J.303.1393