oil filter JAGUAR S TYPE 2005 1.G Electrical Manual
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2005, Model line: S TYPE, Model: JAGUAR S TYPE 2005 1.GPages: 200, PDF Size: 5.93 MB
Page 60 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI55 2-WAY / BLACK ENGINE TIMING COVER, CRANKSHAFT PULLEY
CMP SENSOR 1 PI57 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI56 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR IL9 2-WAY / BLACK FUEL RAIL, FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
IMT SOLENOID VALVE 1 PI30 2-WAY / BLACK INTAKE MANIFOLD, REAR
IMT SOLENOID VALVE 2 PI31 2-WAY / BLACK INTAKE MANIFOLD, REAR
IP SENSOR IL12 3-WAY / BLACK FUEL RAIL, REAR
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, TOWARD FRONT, BANK 2 (FRONT SENSOR)
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE BLOCK, REAR, BANK 1 (REAR SENSOR)
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, UPPER REAR
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, FRONT
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFT
VVT SOLENOID VALVE 1 PI16 2-WAY / BLACK RH CYLINDER HEAD, FRONT
VVT SOLENOID VALVE 2 PI17 2-WAY / BLACK LH CYLINDER HEAD, FRONTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
IL10 12-WAY / BLACK / ENGINE HARNESS TO FUEL INJECTOR LINK REAR OF ENGINE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–38 INTAKE MANIFOLD TUNING VALVE SOLENOID DRIVE – 1 / TOP: GROUND WHEN ACTIVATED
O PI1–39 INTAKE MANIFOLD TUNING VALVE SOLENOID DRIVE – 2 / BOTTOM: GROUND WHEN ACTIVATED
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–53 GENERATOR CONTROL: VARIABLE VOLTAGE
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
I PI1–65 GENERATOR FIELD RETURN SIGNAL: VARIABLE VOLTAGE BY GENERATOR OPERATING CONDITION
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
O PI1–109 BANK 1 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
O PI1–110 BANK 2 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED
Page 64 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.3
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI21 2-WAY / BLACK ENGINE UNDER SIDE, FORWARD OF BELL HOUSING
CMP SENSOR 1 PI23 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI22 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR PI27 2-WAY / BLACK FUEL RAIL, RH REAR
EGR VALVE PI15 6-WAY / BLACK INTAKE MANIFOLD, RH FRONT
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
IP SENSOR PI28 3-WAY / BLACK FUEL RAIL, RH FRONT
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, BANK 1
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE VEE, BANK 2
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, LOWER REAR
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, FRONT
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFT
VVT SOLENOID VALVE 1 PI16 2-WAY / BLACK RH CYLINDER HEAD, FRONT
VVT SOLENOID VALVE 2 PI17 2-WAY / BLACK LH CYLINDER HEAD, FRONTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–57 EGR DRIVE 1: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–58 EGR DRIVE 2: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–59 EGR DRIVE 3: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–60 EGR DRIVE 4: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
O PI1–109 BANK 1 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
O PI1–110 BANK 2 VVT SOLENOID VALVE: PWM, 300 Hz, POSITIVE DUTY CYCLE RANGE 0% – 100%
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED
Page 68 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 03.5
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAPP SENSOR CA88 6-WAY / BLACK TOP OF ACCELERATOR PEDAL
BRAKE ON / OFF SWITCH CA37 2-WAY / GREEN TOP OF BRAKE PEDAL
CKP SENSOR PI21 2-WAY / BLACK ENGINE UNDER SIDE, FORWARD OF BELL HOUSING
CMP SENSOR 1 PI23 2-WAY / BLACK BANK 1 (RH) CAMSHAFT COVER, FRONT
CMP SENSOR 2 PI22 2-WAY / BLACK BANK 2 (LH) CAMSHAFT COVER, FRONT
ECT SENSOR PI25 2-WAY / BLACK ENGINE VEE, COOLANT OUTLET CASTING
EFT SENSOR PI27 2-WAY / BLACK FUEL RAIL, RH REAR
EGR VALVE PI15 6-WAY / BLACK INTAKE MANIFOLD, REAR
ENGINE CONTROL MODULE PI1 134-WAY / BLACK FRONT BULKHEAD, P ASSENGER SIDE
EOT SENSOR PI24 2-WAY / BLACK ADJACENT TO OIL FILTER
EVAP CANISTER CLOSE VALVE CA270 2-WAY / BLACK ABOVE REAR AXLE (FUEL TANK COMPONENTS)
EVAP CANISTER PURGE VALVE FH111 2-WAY / BLACK ENGINE COMPARTMENT, LH SIDE, ADJACENT TO SUSPENSION TURRET
FRONT POWER DISTRIBUTION FUSE BOX — — ENGINE COMPARTMENT, RH SIDE
FTP SENSOR FP1 3-WAY / BLACK FUEL TANK PIPING, LH SIDE (UNDER ACCESS PLATE)
HO2 SENSOR DOWNSTREAM 1/2 PI11 4-WAY / BLACK RH EXHAUST, TOP OF CATALYST
HO2 SENSOR DOWNSTREAM 2/2 PI13 4-WAY / BLACK LH EXHAUST, TOP OF CATALYST
HO2 SENSOR UPSTREAM 1/1 PI10 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
HO2 SENSOR UPSTREAM 2/1 PI12 4-WAY / BLACK RH EXHAUST, CATALYST CENTER
IAT SENSOR 2 PI43 2-WAY / BLACK INTAKE MANIFOLD, RH SIDE, REAR
IP SENSOR PI28 3-WAY / BLACK FUEL RAIL, LH REAR
KNOCK SENSOR 1 PI20 2-WAY / BLACK ENGINE VEE, BANK 1
KNOCK SENSOR 2 PI19 2-WAY / BLACK ENGINE VEE, BANK 2
MAF SENSOR PI14 5-WAY / BLACK ENGINE AIR INTAKE, ADJACENT TO AIR CLEANER
MAP SENSOR PI29 4-WAY / BLACK INTAKE MANIFOLD, REAR, BELOW THROTTLE ASSEMBLY
THROTTLE MOTOR PI18 2-WAY / BLACK ENGINE AIR INTAKE, REAR
THROTTLE MOTOR RELAY — — FRONT POWER DISTRIBUTION FUSE BOX – R5
TP SENSOR PI26 4-WAY / BLACK THROTTLE BODY, THROTTLE SHAFTHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationFC12 14-WAY / GREY / FASCIA HARNESS TO FRONT HARNESS BEHIND INSTRUMENT PANEL, PASSENGER SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FH1 20-WAY / BLACK / CABIN HARNESS TO FRONT HARNESS RH ‘A’ POST, LOWER
FH3 16-WAY / BLUE / CABIN HARNESS TO FRONT HARNESS LH ‘A’ POST
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationPI40 (LHD) ENGINE COMPARTMENT, BEHIND RH WHEEL ARCH LINER
PI40 (RHD) ENGINE COMPARTMENT, BEHIND LH WHEEL ARCH LINER
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Engine Control Module
Pin Description and CharacteristicO PI1–1 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–2 HO2 SENSOR HEATER CONTROL – 1/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
PG PI1–4 POWER GROUND 1: GROUND
PG PI1–5 POWER GROUND 2: GROUND
I PI1–6 ENGINE CRANK: B+
I PI1–7 IGNITION ON: B+
I PI1–8 BRAKE ON / OFF SWITCH: NORMALLY OPEN / B+ WHEN ACTIVATED
I PI1–10 INERTIA SWITCH: NORMALLY CLOSED / OPEN CIRCUIT WHEN ACTIVATED
SS PI1–12 SENSOR POWER SUPPLY 1: NOMINAL 5 V
SS PI1–13 SENSOR POWER SUPPLY 2: NOMINAL 5 V
SG PI1–17 SMALL SIGNAL GROUND 1: GROUND
SG PI1–18 SMALL SIGNAL GROUND 2: GROUND
SG PI1–19 SENSOR GROUND 1: GROUND
SG PI1–20 SENSOR GROUND 2: GROUND
B+ PI1–22 BATTERY POWER SUPPLY: B+
B+ PI1–23 EMS SWITCHED POWER SUPPLY 1: B+
B+ PI1–24 EMS SWITCHED POWER SUPPLY 2: B+
SG PI1–29 HO2 SENSOR HEATER GROUND – 1/1: GROUND
SG PI1–30 HO2 SENSOR HEATER GROUND – 1/1: GROUND
I PI1–31 AUTOMATIC – PARK / NEUTRAL SIGNAL: B+ WHEN ACTIVATED MANUAL, ROW – PARK / NEUTRAL SIGNAL: B+ WHEN IGNITION CRANK (III)
MANUAL, NAS – CLUTCH PEDAL SAFETY SWITCH (PARK / NEUTRAL SIGNAL): B+ WHEN ACTIVATED
I PI1–36 CRANKSHAFT SENSOR SIGNAL: PULSED SIGNAL, 70 PULSES PER ENGINE CYCLE
SG PI1–37 CRANKSHAFT SENSOR SIGNAL GROUND: GROUND
O PI1–40 EMS CONTROL RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
O PI1–41 STARTER RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–43 TP AND APP SIGNALS SHIELD: GROUND
I PI1–44 MASS AIR FLOW SENSOR SIGNAL: NOMINAL 0 – 5 V BY ENGINE OPERATING CONDITION
SG PI1–45 MASS AIR FLOW SENSOR GROUND: GROUND
SG PI1–46 MASS AIR FLOW SENSOR GROUND: GROUND
I PI1–50 ENGINE FUEL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
O PI1–52 THROTTLE MOTOR RELAY DRIVE: TO ACTIVATE, ECM SWITCHES CIRCUIT TO GROUND
SG PI1–54 THROTTLE MOTOR GROUND: GROUND
O PI1–55 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–56 HO2 SENSOR HEATER CONTROL – 2/1: PWM, 1 CYCLE PER 128 mS, VARIABLE DUTY CYCLE
O PI1–57 EGR DRIVE 1: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–58 EGR DRIVE 2: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–59 EGR DRIVE 3: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–60 EGR DRIVE 4: B+; EGR DRIVE 1, 2, 3 AND 4 ARE OPERATED IN TURN
O PI1–66 EVAP CANISTER PURGE VALVE DRIVE: PWM, 10 Hz, POSITIVE DUTY CYCLE RANGE 7% – 100%
O PI1–67 EVAP CANISTER CLOSE VALVE DRIVE: TO CLOSE, ECM SWITCHES CIRCUIT TO GROUND
I PI1–68 BANK 2 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–69 BANK 2 CAMSHAFT SENSOR GROUND: GROUND
I PI1–70 ENGINE COOLANT TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–71 INTAKE AIR TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–72 INTAKE AIR TEMPERATURE SENSOR 2 SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–73 INJECTION PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: POTENTIOMETER – VOLTAGE INCREASES AS PRESSURE INCREASES
I PI1–75 THROTTLE POSITION SENSOR 1 SIGNAL: IDLE = 0.60 V; FULL THROTTLE = 4.30 V
I PI1–76 THROTTLE POSITION SENSOR 2 SIGNAL: IDLE = 1.48 V; FULL THROTTLE = 4.40 V
I PI1–78 ENGINE OIL TEMPERATURE SENSOR SIGNAL, NOMINAL 0 – 5 V: NTC SENSOR – VOLTAGE DECREASES AS TEMPERATURE INCREASES
I PI1–79 GENERATOR FAULT; CHARGE WARNING
O PI1–80 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
SG PI1–81 HO2 SENSOR HEATER GROUND – 2/1: GROUND
SG PI1–82 HO2 SENSOR HEATER GROUND – 2/1: GROUND
I PI1–83 HO2 SENSOR 1/1 SIGNAL: VARIABLE CURRENT
I PI1–84 HO2 SENSOR 1/1 SIGNAL: CONSTANT CURRENT
SG PI1–91 HO2 SENSOR HEATERS 1/2, 2/2 GROUND: GROUND
O PI1–92 HO2 SENSOR HEATER CONTROL – 1/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
O PI1–93 HO2 SENSOR HEATER CONTROL – 2/2: PWM, 1 CYCLE PER 256 mS, POSITIVE DUTY CYCLE RANGE 0 mS = 0%, 77 mS = 30%, 256 mS = 100%
I PI1–94 BANK 1 CAMSHAFT SENSOR SIGNAL: PULSED SIGNAL, 4 PULSES PER ENGINE CYCLE
SG PI1–95 BANK 1 CAMSHAFT SENSOR GROUND: GROUND
I PI1–98 BANK 1 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
I PI1–99 BANK 2 KNOCK SENSOR SIGNAL: VARIABLE VOLTAGE DEPENDENT ON ENGINE VIBRATION
SG PI1–100 SENSOR SHIELD: GROUND
I PI1–102 ACCELERATOR PEDAL POSITION SENSOR 1 SIGNAL: FOOT OFF = 0.75 V; FULLY DEPRESSED = 3.40 V (AUTO) 3.20 V (MAN)
I PI1–103 ACCELERATOR PEDAL POSITION SENSOR 2 SIGNAL: FOOT OFF = 3.38 V; FULLY DEPRESSED = 2.05 V (AUTO) 2.14 V (MAN)
I PI1–104 FUEL TANK PRESSURE SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS PRESSURE INCREASES
D PI1–105 SERIAL DATA LINK: SERIAL COMMUNICATION
O PI1–106 THROTTLE MOTOR DRIVE: B+ TO ACTIVATE MOTOR
I PI1–107 HO2 SENSOR 2/1 SIGNAL: VARIABLE CURRENT
I PI1–108 HO2 SENSOR 2/1 SIGNAL: CONSTANT CURRENT
SG PI1–111 FUEL INJECTORS 2, 3, 5, 8 GROUND: GROUND
SG PI1–116 FUEL INJECTORS 1, 4, 6, 7 GROUND: GROUND
C PI1–123 CAN –
C PI1–124 CAN +
I PI1–127 MAP SENSOR SIGNAL, NOMINAL 0 – 5 V: VOLTAGE INCREASES AS MANIFOLD ABSOLUTE PRESSURE INCREASES
I PI1–128 HO2 SENSOR 1/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
I PI1–129 HO2 SENSOR 2/2 SIGNAL, NOMINAL 1 V SWING: 0.1 – 0.9 V SWING
SG PI1–130 HO2 SENSORS SHIELD: GROUND
B+ PI1–134 THROTTLE MOTOR POWER SUPPLY: B+ WHEN RELAY ACTIVATED
Page 92 of 200
Refer to the front of this book for detailed information and illustrations regarding the location and identification of harnesses, relays, fuses, grounds,
control modules and control module pins.
NOTE: The values listed are approximately those that can be expected at the control module connector pins with all circuit conn
ections made and all
components connected and fitted. The following abbreviations are used to represent values for Control Module Pin-Out data
I Input
O Output
B+ Battery Voltage PG Power Ground
SS Sensor / Signal Supply V
SG Sensor / Signal GroundC CAN Network
S SCP Network
D2 D2B Network D Serial and Encoded Data
V Voltage (DC)
PWM Pulse Width Modulated
CAUTION: The information on this data page is furnished to ai d the user in understanding circuit operation. THIS INFORMATION SH OULD BE USED FOR
REFERENCE ONLY.DATE OF ISSUE: May 2004
Fig. 07.1
FOR CONTROL MODULE PIN-OUT INFORMATION, UNFOLD PAGE TO LEFT. COMPONENTS
Component Connector(s) Connector Description LocationAUXILIARY LIGHTING SWITCH FC11 10-WAY / YELLOW FASCIA, ADJACENT TO STEERING COLUMN
ENGINE COOLANT LEVEL SENSOR CP3 2-WAY / BLACK ENGINE COMPARTMENT, COOLANT EXPANSION TANK
FRONT ELECTRONIC MODULE CA24 26-WAY / NATURAL LH ‘A’ POST
CA31 20-WAY / BLACK
FH9 22-WAY / BLACK
FH59 12-WAY / BLACK
FH60 17-WAY / BLACK
FUEL LEVEL SENSOR – LH SIDE (DIESEL) FP14 2-WAY / BLACK FUEL TANK, LH SIDE
FUEL LEVEL SENSOR – LH SIDE (GASOLINE) FP3 4-WAY / BLACK FUEL TANK, LH SIDE
FUEL LEVEL SENSOR – RH SIDE (DIESEL) FP13 6-WAY / GREY FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (GASOLINE) FP4 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (NAS N/A ONLY) FP8 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LEVEL SENSOR – RH SIDE (NAS SC ONLY) FP9 4-WAY / BLACK FUEL TANK, RH SIDE
FUEL LOW LEVEL SWITCH (DIESEL) FP13 6-WAY / GREY FUEL TANK, RH SIDE
IGNITION SWITCH FC18 7-WAY / BLACK STEERING COLUMN COWLING
INSTRUMENT CLUSTER FC8 32-WAY / BLACK INSTRUMENT PANEL FC9 32-WAY / BLACK
MAIN LIGHTING SWITCH (COLUMN SWITCHGEAR) FC116 6-WAY / BLACK STEERING COLUMN COWLING
OIL PRESSURE SWITCH (DIESEL) C29 1-WAY / BLACK ADJACENT TO OIL FILTER
OIL PRESSURE SWITCH (GASOLINE) PI46 1-WAY / BLACK ADJACENT TO OIL FILTER
REAR ELECTRONIC MODULE CA63 17-WAY / BLACK LUGGAGE COMPARTMENT, RH REAR CA100 12-WAY / BLACK
CA101 20-WAY / BLACK
CA102 22-WAY / BLACK
CA103 26-WAY / NATURAL
WASHER FLUID LEVEL SWITCH FH37 2-WAY / BLACK WASHER FLUID CONTAINERHARNESS IN-LINE CONNECTORS
Connector Connector Description / Location LocationCP1 10-WAY / BLACK / INTERCOOLER PUMP LINK LEAD ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
CP7 4-WAY / BLACK / FRONT END HARNESS ENGINE COMPARTMENT, RH FRONT, ADJACENT TO RADIATOR
FC4 14-WAY / GREEN / FASCIA HARNESS IN-LINE CONNECTOR BEHIND INSTRUMENT PANEL, LH SIDE
FC26 16-WAY / BLUE / CABIN HARNESS TO FASCIA HARNESS BEHIND INSTRUMENT PANEL, DRIVER SIDE
FP2 8-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
FP6 2-WAY / BLACK / CABIN HARNESS TO FUEL PUMP HARNESS TOP OF FUEL TANK, RH SIDE
PI41 42-WAY / BLACK / ENGINE HARNESS TO VEHICLE HARNESSES ENGINE COMPARTMENT, BULKHEAD, PASSENGER SIDEGROUNDS
Ground LocationCA156 LUGGAGE COMPARTMENT, RH SIDE
FC38 UNDER CENTER OF INSTRUMENT PANEL, ON TRANSMISSION TUNNEL
FH42 ENGINE COMPARTMENT, BEHIND RH HEADLAMP
FH77 LH LOWER ‘A’ POST, ADJACENT TO THE FRONT ELECTRONIC MODULE (FORWARD OF CA30)
NOTE: Refer to the Appendix at the rear of this book for Network Messages. Front Electronic Module Pin Description and CharacteristicI FH9–15 WASHER FLUID LEVEL SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
S FH59–1 SCP –
B+ FH59–6 BATTERY POWER SUPPLY (LOGIC): B+
S FH59–7 SCP +
I FH59–9 ENGINE OIL PRESSURE SWITCH (NORMALLY OPEN): OPEN CIRCUIT / GROUND
PG FH59–12 POWER GROUND: GROUND
PG FH60–11 POWER GROUND: GROUND
PG FH60–13 POWER GROUND: GROUND
PG FH60–14 POWER GROUND: GROUND
PG FH60–15 POWER GROUND: GROUNDInstrument ClusterPin Description and CharacteristicPG FC8–2 POWER GROUND: GROUND
I FC8–3 SEAT BELT AUDIBLE WARNING REQUEST: AUDIBLE WARNING REQUEST ACTIVE = GROUND
B+ FC8–4 IGNITION SWITCHED POWER SUPPLY (I): B+
I FC8–5 KEY-IN AUDIBLE WARNING: B+ WHEN KEY IN
I FC8–6 KEY-IN AUDIBLE WARNING (J-GATE): GROUND WHEN NOT-IN-PARK
B+ FC8–14 IGNITION SWITCHED POWER SUPPLY (II): B+
B+ FC8–15 BATTERY POWER SUPPLY (LOGIC): B+
SG FC8–18 AUXILIARY LIGHTING SWITCH SIGNAL GROUND: GROUND
I FC8–19 LOW ENGINE COOLANT LEVEL WARNING: GROUND WHEN COOLANT LEVEL LOW
I FC8–23 AIR BAG WARNING: HARD-WIRED TO AIR BAG INDICATOR
B+ FC8–24 IGNITION SWITCHED POWER SUPPLY (II) (AIRBAG WARNING): B+
SG FC8–32 SIGNAL GROUND: GROUND
I FC9–1 TRIP COMPUTER – MESSAGE CENTER SIGNALS: VARIABLE RESISTANCE
SG FC9–10 MAIN LIGHTING SWITCH SIGNAL GROUND: GROUND
C FC9–12 CAN +
C FC9–13 CAN –
I FC9–17 TRIP CYCLE SWITCH – MESSAGE CENTER SIGNAL: VARIABLE RESISTANCE
S FC9–25 SCP +
S FC9–26 SCP –
C FC9–28 CAN +
C FC9–29 CAN –Rear Electronic ModulePin Description and CharacteristicB+ CA101–3 BATTERY POWER SUPPLY: B+
I CA101–15 GASOLINE, RH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
I CA101–16 GASOLINE, LH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
S CA102–1 SCP +
S CA102–2 SCP –
PG CA102–12 POWER GROUND: GROUND
I CA102–17 LOW LEVEL SWITCH
I CA102–20 LOW LEVEL SWITCH
PG CA103–11 POWER GROUND: GROUND
PG CA103–12 POWER GROUND: GROUND
I CA103–17 DIESEL, RH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
I CA103–18 DIESEL, LH FUEL LEVEL SENSOR SIGNAL: VARIABLE RESISTANCE
SG CA103–23 FUEL LEVEL SENSORS SIGNAL GROUND: GROUND
PG CA103–25 POWER GROUND: GROUND
PG CA103–26 POWER GROUND: GROUND