Electrical JAGUAR XFR 2010 1.G Workshop Manual
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2010, Model line: XFR, Model: JAGUAR XFR 2010 1.GPages: 3039, PDF Size: 58.49 MB
Page 227 of 3039
Published: 18-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Remote
Keyless Entry Module (RFA)
Description and Operation
Remote Keyless Entry Module (RFA)
CAUTIONS:
Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not guarantee
confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
When probing connectors to take measurements in the course of the pinpoint tests, use the adaptor kit, part number
3548-1358-00
NOTES:
If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual (section B1.2), or determine if any prior approval programme is in operation, prior to
the installation of a new module/component
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)
When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion
If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals
Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system
The table below lists all diagnostic trouble codes (DTCs) that could be logged in the remote keyless entry module, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Remote Keyless Entry (RKE) Module (419-10 Multifunction Electronic Modules, Diagnosis
and Testing).
DTC Description Possible Causes Action B102B-00
Passive Key - No sub
type information
Response Error - general
failure
Using the manufacturer approved diagnostic
system, clear all passive keys, re-learn all passive
keys B10C1-00
Left Front Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C1-24
Left Front Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck left front unlock switch.
Refer to the electrical circuit diagrams and check
left front unlock switch circuit for short to ground
Page 228 of 3039
DTC Description Possible Causes Action B10C2-00
Left Rear Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C2-24
Left Rear Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck left rear unlock switch.
Refer to the electrical circuit diagrams and check
left rear unlock switch circuit for short to ground B10C3-00
Right Front Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C3-24
Right Front Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck right front unlock switch.
Refer to the electrical circuit diagrams and check
right front unlock switch circuit for short to ground B10C4-00
Right Rear Unlock Pull
Switch - No sub type
information
No power supply to door
handle
Switch circuit open, or
short circuit to power
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check the power supply to the door handle. Check
the switch circuit is not open circuit or short to
power. Repair wiring as required B10C4-24
Right Rear Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck right rear unlock switch.
Refer to the electrical circuit diagrams and check
right front unlock switch circuit for short to ground B10C5-24 Trunk Unlock Pull
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check for stuck luggage compartment lid
unlock switch. Refer to the electrical circuit diagrams
and check luggage compartment lid unlock
switch circuit for short to ground B10C6-1F Exterior Trunk Antenna
- Circuit intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check exterior luggage compartment antenna
circuits for short to ground, power, open circuit B10C7-1F Interior Trunk Antenna
- Circuit intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check interior luggage compartment antenna circuits
for short to ground, power, open circuit B10C8-1F
Interior Center
Antenna - Circuit
intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check interior center antenna circuits for short to
ground, power, open circuit B10C9-1F Interior Front Antenna
- Circuit intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check interior front antenna circuits for short to
Page 229 of 3039
DTC Description Possible Causes Action ground, power, open circuit B10CA-1F
Left Rear Door Handle
Antenna - Circuit
intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check left rear door handle antenna circuits for short
to ground, power, open circuit B10CB-1F
Right Rear Door Handle
Antenna - Circuit
intermittent
Circuit intermittent -
general electrical error
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Refer to the electrical circuit diagrams and
check right rear door handle antenna circuits for
short to ground, power, open circuit B10CC-24
Left Front Latch Clutch
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Check for stuck left front door latch clutch switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10CD-24
Left Rear Latch Clutch
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Check for stuck left rear door latch clutch switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10CE-24
Right Front Latch
Clutch Switch - Signal
stuck high
Signal stuck high - button
stuck in active position
Check for stuck right front door latch clutch switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10CF-24
Right Rear Latch Clutch
Switch - Signal stuck
high
Signal stuck high - button
stuck in active position
Check for stuck right rear door latch clutch switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10D1-24 Left Front Lock Button
- Signal stuck high
Signal stuck high - button
stuck in active position
Check for stuck left front door handle lock switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10D2-24
Left Rear Lock Button -
Signal stuck high
Signal stuck high - button
stuck in active position
Check for stuck left rear door handle lock switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10D3-24
Right Front Lock
Button - Signal stuck
high
Signal stuck high - button
stuck in active position
Check for stuck right front door handle lock switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground B10D4-24 Right Rear Lock Button
- Signal stuck high
Signal stuck high - button
stuck in active position
Check for stuck right rear door handle lock switch.
Refer to the electrical circuit diagrams and check
left front door latch clutch switch circuit for short to
ground U0010-00
Medium Speed CAN
Communication Bus -
No subtype information
No subtype information
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity test using
the manufacturer approved diagnostic system U0140-00
Lost Communication
With Body Control
Module - No subtype
information
Missing message from
CJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity test using
the manufacturer approved diagnostic system. Refer
to the electrical circuit diagrams and check power
and ground supplies to CJB
Page 230 of 3039
DTC Description Possible Causes Action U0142-00
Lost Communication
With Body Control
Module "B" - No
subtype information
Missing message from
RJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity test using
the manufacturer approved diagnostic system. Refer
to the electrical circuit diagrams and check power
and ground supplies to RJB U0155-00
Lost Communication
With Instrument Panel
Cluster (IPC) Control
Module - No subtype
information
Missing message from
instrument cluster
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity test using
the manufacturer approved diagnostic system. Refer
to the electrical circuit diagrams and check power
and ground supplies to instrument cluster U0300-00
Internal Control
Module Software
Incompatibility - No
subtype information
Invalid configuration
message is received
Re-configure the RJB using the manufacturer
approved diagnostic system. Clear the DTC and
retest. If the DTC is still logged suspect the remote
keyless entry module, refer to the new module
installation note at the top of the DTC Index U201F-00
External Receiver - No
subtype information
No subtype information -
communication error
Suspect the RF receiver, check and install a new RF
receiver as required, refer to the new
module/component installation note at top of DTC
Index U201F-13
External Receiver -
Circuit open
Line open
Refer to the electrical circuit diagrams and test RF
receiver communication circuit to remote keyless
entry module for short to ground or open circuit U201F-87
External Receiver -
Missing message
Transmission error
Refer to the electrical circuit diagrams and check
the data line between the RF receiver and the
remote keyless entry module for short, open circuit.
Suspect the RF receiver or remote keyless entry
module, check and install a new RF receiver or
remote keyless entry module as required, refer to
the new module/component installation note at top
of DTC Index U2100-00
Initial Configuration
Not Complete - No
subtype information
No subtype information
Configure the Remote Keyless Entry module using
the manufacturer approved diagnostic system U2101-00
Control Module
Configuration
Incompatible - No subtype information
No subtype information
Re-configure the RJB using the manufacturer
approved diagnostic system U3000-49
Control Module -
Internal electronic
failure
Internal electronic failure
Install a new remote keyless entry module, refer to
the new module installation note at the top of the
DTC Index U3002-81
Vehicle Identification
Number - Invalid serial
data received
Vehicle/component
mis-match. Module
previously installed to
other vehicle
Install correct/new module to vehicle specification,
refer to the new module/component installation
note at the top of the DTC Index U3003-62
Battery Voltage -
Signal compare failure
Mis-match in battery
voltage, of 2 volts or
more, between remote
keyless entry module and
RJB
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system
Refer to the relevant section of the workshop
manual and test the battery and charging system
Page 232 of 3039
DTC Description Possible Causes Action B0001-11
Driver Frontal Stage 1
Deployment Control - Circuit
short to ground
Driver front stage 1 air bag
circuit - short to ground
Refer to electrical circuit diagrams and
test driver front stage 1 air bag circuit
for short to ground B0001-12
Driver Frontal Stage 1
Deployment Control - Circuit
short to battery
Driver front stage 1 air bag
circuit - short to power
Refer to electrical circuit diagrams and
test driver front stage 1 air bag circuit
for short to power B0001-1A
Driver Frontal Stage 1
Deployment Control - Circuit
resistance below threshold
Circuit resistance below
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0001-1B
Driver Frontal Stage 1
Deployment Control - Circuit
resistance above threshold
Circuit resistance above
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0001-1C
Driver Frontal Stage 1
Deployment Control - Circuit
voltage out of range
Driver front stage 1 air bag
circuit - high resistance
Refer to electrical circuit diagrams and
test driver front stage 1 air bag circuit
for high resistance B0001-56
Driver Frontal Stage 1
Deployment Control -
Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0001-95
Driver Frontal Stage 1
Deployment Control - Incorrect
assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test driver front stage 1 air bag circuit
for crosscoupling with other firing loop B0002-09
Driver Frontal Stage 2
Deployment Control -
Component failures
Driver front stage 2 air bag -
internal driver failure
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0002-11
Driver Frontal Stage 2
Deployment Control - Circuit
short to ground
Driver front stage 2 air bag
circuit - short to ground
Refer to the electrical circuit diagrams
and test driver front stage 2 air bag
circuit for short to ground B0002-12
Driver Frontal Stage 2
Deployment Control - Circuit
short to battery
Driver front stage 2 air bag
circuit - short to power
Refer to the electrical circuit diagrams
and test driver front stage 2 air bag
circuit for short to power B0002-1A
Driver Frontal Stage 2
Deployment Control - Circuit
resistance below threshold
Circuit resistance below
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0002-1B
Driver Frontal Stage 2
Deployment Control - Circuit
resistance above threshold
Circuit resistance above
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0002-1C
Driver Frontal Stage 2
Deployment Control - Circuit
voltage out of range
Driver front stage 2 air bag
circuit - high resistance
Refer to electrical circuit diagrams and
test driver front stage 2 air bag circuit
for high resistance B0002-56
Driver Frontal Stage 2
Deployment Control -
Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0002-95
Driver Frontal Stage 2
Deployment Control - Incorrect
assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test driver front stage 2 air bag circuit
for crosscoupling with other firing loop B0010-09
Passenger Frontal Stage 1
Deployment Control -
Component failures
Passenger front stage 1 air
bag - internal driver failure
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system
Page 233 of 3039
DTC Description Possible Causes Action B0010-11
Passenger Frontal Stage 1
Deployment Control - Circuit
short to ground
Passenger front stage 1 air
bag circuit - short to ground
Refer to the electrical circuit diagrams
and test passenger front stage 1 air bag
circuit for short to ground B0010-12
Passenger Frontal Stage 1
Deployment Control - Circuit
short to battery
Passenger front stage 1 air
bag circuit - short to power
Refer to the electrical circuit diagrams
and test passenger front stage 1 air bag
circuit for short to power B0010-1A
Passenger Frontal Stage 1
Deployment Control - Circuit
resistance below threshold
Circuit resistance below
threshold
Carry out the pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0010-1B
Passenger Frontal Stage 1
Deployment Control - Circuit
resistance above threshold
Circuit resistance above
threshold
Carry out the pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0010-1C
Passenger Frontal Stage 1
Deployment Control - Circuit
voltage out of range
Passenger front stage 1 air
bag circuit - high resistance
Refer to electrical circuit diagrams and
test passenger front stage 1 air bag
circuit for high resistance B0010-56
Passenger Frontal Stage 1
Deployment Control -
Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0010-95
Passenger Frontal Stage 1
Deployment Control - Incorrect
assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test passenger front stage 1 air bag
circuit for crosscoupling with other firing
loop B0011-09
Passenger Frontal Stage 2
Deployment Control -
Component failures
Passenger front stage 2 air
bag - internal driver failure
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0011-11
Passenger Frontal Stage 2
Deployment Control - Circuit
short to ground
Passenger front stage 2 air
bag circuit - short to ground
Refer to the electrical circuit diagrams
and test passenger front stage 2 air bag
circuit for short to ground B0011-12
Passenger Frontal Stage 2
Deployment Control - Circuit
short to battery
Passenger front stage 2 air
bag circuit - short to power
Refer to the electrical circuit diagrams
and test passenger front stage 2 air bag
circuit for short to power B0011-1A
Passenger Frontal Stage 2
Deployment Control - Circuit
resistance below threshold
Circuit resistance below
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0011-1B
Passenger Frontal Stage 2
Deployment Control - Circuit
resistance above threshold
Circuit resistance above
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0011-1C
Passenger Frontal Stage 2
Deployment Control - Circuit
voltage out of range
Passenger front stage 2 air
bag circuit - high resistance
Refer to electrical circuit diagrams and
test passenger front stage 2 air bag
circuit for high resistance B0011-56
Passenger Frontal Stage 2
Deployment Control -
Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0011-95
Passenger Frontal Stage 2
Deployment Control - Incorrect
assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test passenger front stage 2 air bag
circuit for crosscoupling with other firing
loop
Page 234 of 3039
DTC Description Possible Causes Action B0020-09
Left Side Air Bag Deployment
Control - Component failures
Left side air bag circuit -
internal driver failure
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0020-11
Left Side Air Bag Deployment
Control - Circuit short to
ground
Left side air bag circuit -
short to ground
Refer to the electrical circuit diagrams
and test left side air bag circuit for short
to ground B0020-12
Left Side Air Bag Deployment
Control - Circuit short to
battery
Left side air bag circuit -
short to power
Refer to the electrical circuit diagrams
and test left side air bag circuit for short
to power B0020-1A
Left Side Air Bag Deployment
Control - Circuit resistance
below threshold
Circuit resistance below
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0020-1B
Left Side Air Bag Deployment
Control - Circuit resistance
above threshold
Circuit resistance above
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0020-1C
Left Side Air Bag Deployment
Control - Circuit voltage out of
range
Left side air bag circuit -
high resistance
Refer to electrical circuit diagrams and
test left side air bag circuit for high
resistance B0020-56
Left Side Air Bag Deployment
Control - Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0020-95
Left Side Air Bag Deployment
Control - Incorrect assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test left side air bag circuit for
crosscoupling with other firing loop B0028-09
Right Side Air Bag Deployment
Control - Component failures
Right side air bag circuit -
internal driver failure
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0028-11
Right Side Air Bag Deployment
Control - Circuit short to
ground
Right side air bag circuit -
short to ground
Refer to the electrical circuit diagrams
and test right side air bag circuit for
short to ground B0028-12
Right Side Air Bag Deployment
Control - Circuit short to
battery
Right side air bag circuit -
short to power
Refer to the electrical circuit diagrams
and test right side air bag circuit for
short to power B0028-1A
Right Side Air Bag Deployment
Control - Circuit resistance
below threshold
Circuit resistance below
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0028-1B
Right Side Air Bag Deployment
Control - Circuit resistance
above threshold
Circuit resistance above
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0028-1C
Right Side Air Bag Deployment
Control - Circuit voltage out of
range
Right side air bag circuit -
high resistance
Refer to electrical circuit diagrams and
test right side air bag circuit for high
resistance B0028-56
Right Side Air Bag Deployment
Control - Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0028-95
Right Side Air Bag Deployment
Control - Incorrect assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test right side air bag circuit for
crosscoupling with other firing loop
Page 235 of 3039
DTC Description Possible Causes Action B0029-09
Right Curtain Deployment
Control 1 - Component failures
Right curtain deployment
control 1 circuit - internal
driver failure
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0029-11
Right Curtain Deployment
Control 1 - Circuit short to
ground
Right curtain deployment
control 1 circuit - short to
ground
Refer to electrical circuit diagrams and
check right curtain deployment control 1
circuit for short to ground B0029-12
Right Curtain Deployment
Control 1 - Circuit short to
battery
Right curtain deployment
control 1 circuit - short to
power
Refer to electrical circuit diagrams and
check right curtain deployment control 1
circuit for short to power B0029-1A
Right Curtain Deployment
Control 1 - Circuit resistance
below threshold
Circuit resistance below
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0029-1B
Right Curtain Deployment
Control 1 - Circuit resistance
above threshold
Circuit resistance above
threshold
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0029-1C
Right Curtain Deployment
Control 1 - Circuit voltage out
of range
Right curtain deployment
control 1 circuit - high
resistance
Refer to electrical circuit diagrams and
test right curtain deployment control 1
circuit for high resistance B0029-56
Right Curtain Deployment
Control 1 - Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0029-95
Right Curtain Deployment
Control 1 - Incorrect assembly
Crosscoupling with other
firing loop
Refer to electrical circuit diagrams and
test right curtain deployment control 1
circuit for crosscoupling with other firing
loop B0050-11
Driver Safety Belt Sensor -
Circuit short to ground
Driver safety belt sensor
circuit - short to ground
Refer to the electrical circuit diagrams
and test driver safety belt sensor circuit
for short to ground B0050-12
Driver Safety Belt Sensor -
Circuit short to battery
Driver safety belt sensor
circuit - short to power
Refer to the electrical circuit diagrams
and test driver safety belt sensor circuit
for short to power B0050-13
Driver Safety Belt Sensor -
Circuit open
Driver safety belt sensor
circuit - open circuit
Refer to the electrical circuit diagrams
and test driver safety belt sensor circuit
for open circuit B0050-1E
Driver Safety Belt Sensor -
Circuit resistance out of range
Driver safety belt sensor
circuit - resistance out of
range
Carry out any pinpoint tests associated
with this DTC using the manufacturer
approved diagnostic system B0050-56
Driver Safety Belt Sensor -
Invalid/incomplete
configuration
Incompatible configuration
Re-configure the RCM using the
manufacturer approved diagnostic
system B0052-11
Passenger Safety Belt Sensor -
Circuit short to ground
Passenger safety belt sensor
circuit - short to ground
Refer to the electrical circuit diagrams
and test passenger safety belt sensor
circuit for short to ground B0052-12
Passenger Safety Belt Sensor -
Circuit short to battery
Passenger safety belt sensor
circuit - short to power
Refer to the electrical circuit diagrams
and test passenger safety belt sensor
circuit for short to power B0052-13
Passenger Safety Belt Sensor -
Circuit open
Passenger safety belt sensor
circuit - open circuit
Refer to the electrical circuit diagrams
and test passenger safety belt sensor
circuit for open circuit
Page 236 of 3039
Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Satellite
Digital Audio Radio System Module (SARM)
Description and Operation
Satellite Radio Module (SARM)
CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:
If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)
When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion
If diagnostic trouble codes are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent
concern may be the cause. Always check for loose connections and corroded terminals
Where an 'on demand self-test' is referred to, this can be accessed via the 'diagnostic trouble code monitor' tab on the
manufacturers approved diagnostic system
Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as needed
The table below lists all diagnostic trouble codes (DTCs) that could be logged on the satellite radio module, for additional
diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System -
General Information, Diagnosis and Testing).
DTC Description Possible Causes Action B1A89-01
Satellite Antenna -
General electrical
failure
Wiring harness fault -
Coaxial cable between
satellite radio module and
the satellite antenna
Internal electronic failure
- Satellite digital audio
radio antenna
Internal electronic failure
- Satellite radio module
Refer to the electrical circuit diagrams and check
satellite digital audio radio antenna coaxial cable for
short circuit to ground, short circuit to power, open
circuit, high resistance. Repair wiring harness as
required, clear DTC and retest
If fault persists, check and install a new satellite digital
audio radio antenna
If fault persists, check and install a new satellite radio
module
Refer to the warranty policy and procedures manual, or
determine if any prior approval programme is in
operation, prior to the installation of a new
module/component B1A89-11
Satellite Antenna -
Circuit short to
ground
Satellite antenna circuit -
short to ground
Refer to the electrical circuit diagrams and check
satellite antenna circuit for short circuit to ground.
Repair wiring harness as required. Clear DTC and retest www.JagDocs.com
Page 237 of 3039
DTC Description Possible Causes Action B1A89-12
Satellite Antenna -
Circuit short to
battery
Satellite antenna circuit -
short to power
Refer to the electrical circuit diagrams and check
satellite antenna circuit for short circuit to power. Repair
wiring harness as required. Clear DTC and retest B1A89-13
Satellite Antenna -
Circuit open
Satellite antenna circuit -
open circuit, high
resistance
Refer to the electrical circuit diagrams and check
satellite antenna circuit for open circuit, high
resistance. Repair wiring harness as required. Clear DTC
and retest U3000-04
Control Module -
System internal
failures
System internal failure
Check and install a new satellite radio module as
required. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3000-4A Control Module -
Satellite radio module -
Using the manufacturer approved diagnostic system Incorrect component Incorrect component select the vehicle configuration main menu>vehicle installed installed configuration>display and modify the vehicle Car configuration configuration file data mismatch Check update as required U3000-55
Control Module -
Not configured
Satellite radio module -
Incorrect component
installed
Incorrect car configuration
file data received
Using the manufacturer approved diagnostic system
select the vehicle configuration main menu>select
configure existing modules menu and program the
satellite radio module U3000-87
Control Module -
Missing message
The satellite radio module
has not received the
configuration file
Master module not
transmitting configuration
file
Using the manufacturer approved diagnostic system
check that the satellite radio module is configured
correctly
Check that the configuration file is being transmitted by
the master module
Using the manufacturer approved diagnostic system,
complete a MOST network integrity test U3000-98
Control Module -
Component or
system over
temperature
Satellite radio module
cooling vents obstructed
Wiring harness fault
Internal electronic failure
Check for possible causes of the satellite radio module
overheating. Check that the ventilation is not
obstructed
Check for short circuit related DTCs. Refer to the
electrical circuit diagrams and check ground circuit for
high resistance. Check antenna circuit for short to power
or ground. Repair wiring harness as required. Clear DTC
and retest
Check for internal electronic failure related DTCs
If fault persists, check and install a new satellite radio
module. Refer to the warranty policy and procedures
manual, or determine if any prior approval programme is
in operation, prior to the installation of a new
module/component U3003-62
Battery Voltage -
Signal compare
failure
Signal compare failure
Satellite radio module
voltage differs more than
±2V compared to rear
junction box voltage
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge and
starting/charging system performance. Check power
supply circuit from rear junction box to satellite radio
module
Refer to electrical circuit diagrams and check the power
and ground supply circuits to the module. Repair wiring
harness as required. Clear DTC and retest