battery JAGUAR XFR 2010 1.G Manual Online

DTC Description Possible Causes Action B1B42-96 Front Left Inner Sensor
- Component internal
failure
Wiring harness fault
Front left inner sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the front
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B44-01
Rear Right Outer
Sensor - General
electrical failure
Wiring harness fault
Rear Right Outer Sensor
- Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B44-12
Rear Right Outer
Sensor - Circuit short
to battery
Wiring harness fault
Refer to electrical wiring diagrams and check the rear
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B44-96
Rear Right Outer
Sensor - Component
internal failure
Wiring harness fault
Rear Right Outer Sensor
- Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B46-01
Rear Right Inner
Sensor - General
electrical failure
Wiring harness fault
Rear Right Inner Sensor
- Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for

DTC Description Possible Causes Action signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B46-12
Rear Right Inner
Sensor - Circuit short
to battery
Wiring harness fault
Refer to electrical wiring diagrams and check the rear
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B46-96
Rear Right Inner
Sensor - Component
internal failure
Wiring harness fault
Rear Right Inner Sensor
- Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B48-01 Rear Left Outer Sensor
- General electrical
failure
Wiring harness fault
Rear Left Outer Sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B48-12 Rear Left Outer Sensor
- Circuit short to
battery
Wiring harness fault
Refer to electrical wiring diagrams and check the rear
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B48-96 Rear Left Outer Sensor
- Component internal
failure
Wiring harness fault
Rear Left Outer Sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the

DTC Description Possible Causes Action bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B50-01 Rear Left Inner Sensor
- General electrical
failure
Wiring harness fault
Rear Left Inner Sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B50-12 Rear Left Inner Sensor
- Circuit short to
battery
Wiring harness fault
Refer to electrical wiring diagrams and check the rear
bumper harness for damage. Check sensor circuit for
short circuit to power. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test B1B50-96 Rear Left Inner Sensor
- Component internal
failure
Wiring harness fault
Rear Left Inner Sensor -
Component internal
failure
Refer to electrical wiring diagrams and check the rear
bumper harness for damage/corrosion. Check sensor
circuit for short circuit to ground, short circuit to
power, open circuit. Repair or replace any wiring
harness as required
Check the connector for integrity and damage, then
re-connect sensor to confirm connection
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test
If the problem persists remove the suspect sensor
from the bumper. Inspect the sensor connector for
signs of water ingress/corrosion. Exchange the
suspect sensor with another sensor within the
bumper that is not reporting a fault. Clear the DTC
and run the on demand self test to confirm if the
fault code now appears for the new position of the
suspect sensor. Renew the faulty sensor B1B54-11 Function LED - Park Aid
- Circuit short to
ground
Wiring harness fault
Switch/LED - Component
internal failure
Refer to electrical wiring diagrams and check the
parking aid LED circuit for short circuit to ground.
Repair or replace any wiring harness as required
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test. If the
problem persists, suspect the switch/LED B1B54-12 Function LED - Park Aid
- Circuit short to
battery
Wiring harness fault
Switch/LED - Component
internal failure
Control Module -
Component internal
failure
Refer to electrical wiring diagrams and check the
parking aid LED circuit for short circuit to power.
Repair or replace any wiring harness as required
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test. If the
problem persists, suspect the switch/LED B1B57-11
Front Sensors Power
Circuit- Circuit short to
ground
Wiring harness fault
Control Module -
Component internal
failure
Check front and rear bumper harness for signs of
damage and security of connections
Refer to electrical wiring diagrams and check the
parking assist front sensor power circuit and rear
sensor power circuit for short circuit to ground. Repair
or replace any wiring harness as required
Using the manufacturers approved diagnostic system
clear the DTC and run the on demand self test. If the
problem persists, suspect the control module www.JagDocs.com

DTC Description Possible Causes Action U0300-00
Internal Control
Module Software
Incompatibility - No
sub type information
Car configuration file
stored in parking aid
control module does not
match the master car
configuration file
Master car configuration
file not being
transmitted by master
control module
Using the manufacturer approved diagnostic system,
check all other control modules, for related DTCs and
refer to the relevant DTC index
Check the components installed on the vehicle were
installed by the factory or a dealer
Install the original component or a new one as
required U0422-00
Invalid Data Received
From Body Control
Module - No sub type
information
Invalid data received
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U0423-00
Invalid Data Received
From Instrument Panel
Control Module - No
sub type information
Invalid data received
Using the manufacturer approved diagnostic system,
check instrument cluster, for related DTCs and refer
to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U0443-00
Invalid Data Received
From Body Control
Module "B" - No sub
type information
Invalid data received
Using the manufacturer approved diagnostic system,
check auxiliary junction box, for related DTCs and
refer to the relevant DTC index
Using the manufacturer approved diagnostic system,
complete a CAN network integrity test
Cycle the ignition off, then on, and check if the DTC
is still logged
Clear the DTC and re-test U2100-00
Initial Configuration
Not Complete - No sub
type information
Car configuration file not
the same as expected by
the parking aid control
module
NOTE: After updating the car configuration file, set the
ignition to on and wait 30 seconds before clearing the DTCs

Using the manufacturer approved diagnostic system,
check and update the car configuration file as
required. Clear the DTC and retest U2101-00
Control Module
Configuration
Incompatible - No sub
type information
Parking aid control
module configuration
error
Using the manufacturer approved diagnostic system
check and up-date the car configuration file as
required. Clear the DTC and re-test U3000-49
Control Module -
Internal electronic
failure
Parking aid control
module internal failure
Using the manufacturers approved diagnostic system
clear the DTC, cycle the ignition off, then on, and
check if the DTC is still logged
If the DTC is still logged suspect the parking aid
control module U3002-81
Vehicle Identification
Number - Invalid serial
data received
VIN Mismatch, stored
VIN does not match
broadcast VIN
Using the manufacturers approved diagnostic system
clear the DTC, cycle the ignition off, then on, and
check if the DTC is still logged
If the DTC is still logged replace the parking aid
control module U3003-16
Battery voltage -
Circuit voltage below
threshold
Circuit voltage below
threshold
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits

DTC Description Possible Causes Action for short circuit to ground, short circuit to power,
open circuit
Clear the DTC and retest U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage above
threshold
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits
for short circuit to ground, short circuit to power,
open circuit
Clear the DTC and retest U3003-62
Battery Voltage -
Signal compare failure
Signal compare failure in
battery voltage, of 2
volts or more, between
parking aid control
module and central
junction box
Using the manufacturer approved diagnostic system,
check central junction box, for related DTCs and refer
to the relevant DTC index
Check the vehicle charging system performance to
ensure the voltage regulation is correct
Refer to relevant section of workshop manual and
battery care manual. Check battery state of charge
and starting/charging system performance
Refer to the electrical circuit diagrams and check
parking aid control module power and ground circuits
for short circuit to ground, short circuit to power,
open circuit
Clear the DTC and retest

Published: 18-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Pedestrian
Protection System Control Module (PPSCM)
Description and Operation

Pedestrian Protection System Control Module (PPSCM)


WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY MUST
BE DEPLETED BEFORE REPAIRING OR REPLACING ANY PEDESTRIAN PROTECTION SYSTEM COMPONENTS. TO DEPLETE THE
BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT TWO MINUTES. FAILURE TO FOLLOW
THIS INSTRUCTION MAY RESULT IN PERSONAL INJURY.


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Pedestrian Protection System Control
Module (PPSCM). For additional diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the
workshop manual.
For additional information, refer to: Pedestrian Protection System (501-20C Pedestrian Protection System, Diagnosis and Testing).

DTC Description Possible Causes Action B1001-11
Right Hood Deployment
Control - Circuit short to
ground
Right hood deployment
control circuit short circuit
to ground
Refer to the electrical circuit diagrams and
check the right hood deployment control circuit
for short circuit to ground. Install a new wiring
harness as necessary. If no wiring harness
fault exists, using the manufacturer approved
diagnostic system, clear the DTCs and retest.
If the fault persists, install a new right hood
deployment control B1001-12
Right Hood Deployment
Control - Circuit short to
battery
Right hood deployment
control circuit short circuit
to power
Refer to the electrical circuit diagrams and
check the right hood deployment control circuit
for short circuit to power. Install a new wiring
harness as necessary. If no wiring harness
fault exists, using the manufacturer approved
diagnostic system, clear the DTCs and retest.
If the fault persists, install a new right hood
deployment control

Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Rear
Differential Control Module (RDCM)
Description and Operation

Rear Differential Control Module (RDCM)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle
NOTES:


If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
warranty policy and procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system)


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places and with a
current calibration certificate. When testing resistance, always take the resistance of the digital multimeter leads into account


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals


If the rear differential control module, rear differential actuator or the rear differential are replaced, the on demand self
test (ODST) must be carried out to calibrate the components


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as needed

The table below lists all diagnostic trouble codes (DTCs) that could be logged in the rear differential control module, for
additional diagnosis and testing information refer to the relevant diagnosis and testing section.
For additional information, refer to: Rear Drive Axle and Differential (205-02 Rear Drive Axle/Differential, Diagnosis and
Testing).

DTC Description Possible Causes Action P0562-00
System Voltage Low -
No sub type
information
Rear differential control
module voltage supply
below 9 volts
Check the battery charge condition, refer to the
electrical circuit diagrams and check the wiring to
the rear differential control module, repair as
necessary P0563-00
System Voltage High -
No sub type
information
System voltage high
(supply voltage supply
greater than 16 volts)
Check engine control module for stored DTCs,
suspect charging system fault. Refer to the
electrical circuit diagrams and check, power and
ground circuit for fault P0604-00
Internal Control Module
Random Access Memory
(RAM) Error - No sub
type information
Rear differential control
module internal error
Clear the DTC and retest. If the problem persists,
renew the control module. Refer to the warranty
policy and procedures manual, or determine if any
prior approval programme is in operation, prior to
the installation of a new module/component P0605-00
Internal Control Module
Read Only Memory
(ROM) Error - No sub
type information
Rear differential control
module internal error
Clear the DTC and retest. If the problem persists,
renew the control module. Refer to the warranty
policy and procedures manual, or determine if any www.JagDocs.com

Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Rear
Junction Box (RJB)
Description and Operation

Rear Junction Box (RJB)


CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:


If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.


Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).


When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.


Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.


Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.


If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.


Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.

The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Rear Junction Box (RJB). For additional
diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Communications Network (418-00 Module Communications Network, Diagnosis and Testing).

DTC Description Possible Causes Action P0460-11
Fuel Level Sensor A
Circuit - Circuit short to
ground
Fuel level sensor A
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor A analogue input circuit for short to
ground P0460-15
Fuel Level Sensor A
Circuit - Circuit short to
battery or open
Fuel level sensor A
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor A analogue input circuit for short to
power, open circuit P0571-12
Brake Switch A Circuit -
Circuit short to battery
Footbrake switch digital
input signal circuits -
short to power
Refer to the electrical circuit diagrams and check
footbrake switch digital input signal circuits for
short to power P1230-12
Fuel Pump Low Speed
Malfunction (VLCM) -
Circuit short to battery
High Side output not
driven - Diagnosis
feedback indicates
output is short to power
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to power

DTC Description Possible Causes Action P1230-14
Fuel Pump Low Speed
Malfunction (VLCM) -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is short to
ground, open circuit
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to ground, open
circuit P1230-93
Fuel Pump Low Speed
Malfunction (VLCM) - No
operation
High Side output not
driven - Diagnosis
feedback indicates
output is at open load
or short to power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel pump delivery module for short to power, open
circuit P1346-11
Fuel Level Sensor B
Circuit - Circuit short to
ground
Fuel level sensor B
analogue input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor B analogue input circuit for short to
ground P1346-15
Fuel Level Sensor B
Circuit - Circuit short to
battery or open
Fuel level sensor B
analogue input circuit -
short to power, open
circuit
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
fuel level sensor B analogue input circuit for short to
power, open circuit P1624-13
Anti-theft System -
Circuit open
Anti-theft signal circuit
from CJB - open circuit
Refer to the electrical circuit diagrams and check
anti-theft signal circuit from CJB for open circuit C111A-11
Right Stop Lamp -
Circuit short to ground
Right stomp lamp
control circuit - short to
ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for short to ground C111A-12
Right Stop Lamp -
Circuit short to battery
Right stomp lamp
control circuit - short to
power
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for short to power C111A-13
Right Stop Lamp -
Circuit open
Right stomp lamp
control circuit - open
circuit
Refer to the electrical circuit diagrams and check
right stomp lamp control circuit for open circuit C111B-11
Left Stop Lamp - Circuit
short to ground
Left stomp lamp control
circuit - short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check left
stomp lamp control circuit for short to ground C111B-13
Left Stop Lamp - Circuit
open
Left stomp lamp control
circuit - open circuit
Refer to the electrical circuit diagrams and check left
stomp lamp control circuit for open circuit C1120-11
Reversing lamp - Circuit
short to ground
Reverse lamp control
circuit - short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short to ground C1120-12
Reversing lamp - Circuit
short to battery
Reverse lamp control
circuit - short to power
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short to power C1120-13
Reversing lamp - Circuit
open
Reverse lamp control
circuit - open circuit
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for open circuit C1120-15
Reversing lamp - Circuit
short to battery or open
Reverse lamp control
circuit - short circuit to
power, open circuit, high
resistance
Refer to the electrical circuit diagrams and check
reverse lamp control circuit for short circuit to power,
open circuit, high resistance. Repair wiring harness
as required. Clear DTC and retest

DTC Description Possible Causes Action B100A-51 Fuel Pump Authorisation
- Not programmed
RJB fault
Low speed CAN fault
Instrument cluster fault
Check power and ground supplies to RJB. Check CAN
communications between RJB and instrument
cluster. Check power and ground supplies to
instrument cluster B100A-62 Fuel Pump Authorisation
- Signal compare failure
Low speed CAN fault
RJB fault
Instrument cluster fault
Incorrect module
installed
(RJB/Instrument cluster)
Write target SID
synchronisation error
following
re-programming
Noise/EMC related error
Check CAN communications between RJB and
instrument cluster. Check power and ground supplies
to RJB and instrument cluster. Confirm correct
module installed. Re-synchronise ID by
re-configuring the RJB as a new module. Check CAN
network for interference/EMC related issues B100A-63 Fuel Pump Authorisation
- Circuit/component
protection time-out
RJB fault
Low speed CAN fault
Instrument cluster fault
Low battery voltage <9V
Check power and ground supplies to RJB and
instrument cluster. Check CAN communications
between RJB and instrument cluster. Check battery
is in fully charged and serviceable condition, refer to
the battery care manual B1026-12
Steering Column Lock -
Circuit short to battery
Steering column lock
ground circuit - short to
power
Refer to the electrical circuit diagrams and check
steering column lock ground circuit for short to
power B1087-83
LIN Bus "A" - Value of
signal protection
calculation incorrect
The checksum of the
received LIN frame is
incorrect
Check the battery monitoring system and rear
parking aid system for DTCs and refer to relevant
DTC Index B1087-86
LIN Bus "A" - Signal
invalid
The header of the LIN
message received is
incorrect
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Check the battery monitoring system and rear
parking aid system for DTCs and refer to relevant
DTC Index B1087-88 LIN Bus "A" - Bus off
Battery monitoring
system LIN circuit -
short to ground, power
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
battery monitoring system LIN circuit for short to
ground, power B108A-23
Start Button - Signal
stuck low
Start/Stop switch digital
input signal circuit -
stuck low
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
Start/Stop switch digital input signal circuit for short
to ground B10A1-11 Trailer Tow Detection -
Circuit short to ground
Trailer tow detection
digital input circuit -
short to ground
Carry out any pinpoint test associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check
trailer tow detection digital input circuit for short to
ground B10AF-12
Blower Fan Relay -
Circuit short to battery
High Side output not
driven - Diagnosis
feedback indicates
output is short to power
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to power B10AF-14
Blower Fan Relay -
Circuit short to ground
or open
High Side output not
driven - Diagnosis
feedback indicates
output is short to
ground, open circuit
Refer to the electrical circuit diagrams and check
blower motor supply circuit for short to ground, open
circuit