instrument panel JAGUAR XJ 2004 X350 / 3.G Owners Manual

3 - 12 Before Driving
Seat belt fitting
!WARNING:
Do not adjust the seat belt while
driving.
Draw the tongue of the seat belt over the
shoulder, across the chest and push it
into the buckle unit slot. A positive ‘click’
indicates that it is safely locked.
Comfort clips or devices that create slack
in the seat belts are not recommended. Ensure that the webbing is midway
between the neck and the edge of the
shoulder. Correct tension is controlled by
automatic retraction of the reel.
A warning light on the instrument panel
is illuminated when the driver’s seat belt
is not fastened.
Note:
If the vehicle is parked on unlevel
ground, the seat belt mechanism may
lock. This is not a fault, gently ease the
belt from its attachment to unlock it.

4-12 On the Road
Message Centre
Driver information, messages and data
are displayed on the message centre
display panel situated within the
instrument cluster.
For the message centre to operate the
ignition must be switched ON
(position ‘II’).
The primary function of the message
centre is to inform the driver of the
following:
• Warning messages.
• Temporary alert messages.
• Information messages.The message centre displays:
• The total distance covered by the
vehicle.
• Trip computer information.
• Warning messages if system faults are detected.
• Status messages to indicate changes in
state of certain vehicle functions.
Messages
!WARNING:
If a red warning light is displayed,
investigate immediately and,
if necessary, stop the vehicle as soon
as possible but only when it is safe to
do so.
Most messages, when displayed, have an
associated warning light, red or amber,
above the display which will come on to
indicate the message priority.
If more than one message is active, each
is displayed in turn for two seconds in
order of priority.
Messages take priority over the odometer
reading or trip computer data and,
if active, will be displayed when the
ignition is switched ON. Message centre illumination
The message centre is lit at all times when
the ignition is ON, and message
brightness is controlled by the dimmer
switch.
All information displayed will be brightly
lit if the exterior light switch is OFF.
Note:
Warning lights are always brightly
lit and are not affected by the dimmer
switch.
Language Selection
The displayed language can be changed
to another language, if required.
Press the ML/km button on the trip
computer switchpack and whilst pressing,
turn on the ignition to position ‘II’.
Now press the ML/km button, each press
will display a different language.
When the desired language is shown,
press the A/B button. After three seconds
the new language will be displayed for
every message.
Note: If you wish to exit the language
changing procedure and keep the original
language, do not press the A/B button but
wait 10 seconds or turn the ignition off.

On the Road 4 - 25
The fog lights can only be switched on
when the ignition switch is in position ‘II’.
Front fog lights (A)
With the lights on in sidelight or dip
position, press the switch (A) to turn on
the front fog lights. Pushing the switch
again will turn off the front fog lights.
A warning light in the instrument cluster
indicates that the fog light is on.
If the sidelights are turned off, the fog
lamps will automatically turn off.
Note: The front fog lights should only be
used when visibility is severely restricted
by fog. Rear fog lights (B)
The rear fog lights can only be switched
on if the dipped headlights are on or if
front fog lights are switched on.
Press the switch (
B) to turn on the rear
fog lights. Pushing the switch again will
turn off the rear fog lights.
A warning lamp in the instrument cluster
indicates that the fog light is on.
When the side lights are switched off the
fog lights will go off.
If the sidelights are le ft on but the ignition
switch is turned to OFF the fog lights will
switch off.Dimmer Switch
The instruments, switchpacks, in-car
entertainment panel and the climate
control panel will be lit when the exterior
lights are switched on.
Push and release the knob to extend it for
ease of operation.
Rotate the knob to adjust the illumination
to the required level.
Push the knob again to place it in the
stowed position.

4-60 On the Road
Use of Headlamps In Daylight
When visibility is poor the headlamps
with dipped beam setting should be
switched on so that the vehicle may be
seen more easily by other road users.
The instrument illumination dimmer
control adjusts the brightness of the panel
lighting.
Engine Oil Consumption
A certain amount of oil consumption is
normal. The rate of consumption will
depend on the following:
• The quality and viscosity of the oil.
• The amount of oxidation and dilution of the oil.
• Climatic conditions.
• The speed at which the engine is being operated.
• Road conditions.
Drivers should expect above normal
consumption when the engine is new,
and after running-in if high speeds are
sustained.
Winter Driving
Freeing a frozen door lock
Caution: Do not ap ply a proprietary
lock de-icer through the keyhole.
Should the lock beco me frozen, warm the
end of the key before use.
Windscreen wiper blades
Before driving away, clear any ice from
the windscreen and check that the wiper
blades are free. Switching on the heated
screen will accelerate this process.
The heated wiper park, if fitted, will come
on automatically.
Frost precautions
The correct concentration of coolant
must be maintained at all times when
‘topping up’ or ‘refilling’ the cooling
system.
Parking the Vehicle
When leaving the vehicle, remember the
following:
• Whenever the vehicle is being parked, apply the parkbrake and move the
gear selector to Park ‘P’.
• Do not leave children or pets in the vehicle unattended.
• Do not leave luggage or valuables on view. Always take your valuables with
you or lock them in the luggage
compartment.
• Remove the ignition key and spare keys, even when the vehicle is in your
garage.
• When the vehicle is unoccupied, close
all windows and lock all doors
securely.
• Park the vehicle where it can be seen. At night, park in a well-lit area.
• Ensure that the keys and the key transmitters are removed from the
vehicle before locking the doors,
and that all doors, the luggage
compartment and the hood are
closed.

5 - 6 Climate Control
Front Climate Controls
The climate control functions are selected
by push buttons and a rotary control.
When a button is pressed, selection of
the function is confirmed by a beep; most
buttons also have an illuminated LED.
Many system functions also have graphic
symbols displayed on the LCD (liquid
crystal display) screen.
Automatic control (AUTO) may be
overridden at any time. Defrost/demist
operation is available and also manual
selection of blower speed,
air distribution, recirculation,
air conditioning and windscreen heating.
Panel illumination
With the exterior lighting switched on or
Autolamps selected at night, the graphics
on the panel controls are illuminated by
low level backlighting.
In countries with daytime runnin g lamps,
the panel illumination will not be on
during daytime if the headlamp switch is
off or in Autolamp position unless it is
dark and the autolamp selects the
headlamps on.
The illumination level is adjusted by the
common instrument panel dimmer
control (see page 4 - 25). 1.
Blower speed and system on/off.
2. Display panel.
3. Fahrenheit/Celsius selector.
4. Air conditioner on/off.
5. Select automatic operation.
6. Recirculation/fresh air.
7. Increase right zone temperature.
8. Decrease right zone temperature. 9.
Select air distribution.
10. Heated rear screen/door mirrors.
11. Heated front screen (optional).
12. Defrost windows.
13. Select dual/single temperature zone.
14. Increase left zone temperature.
15. Decrease left zone temperature.
16. Option without fron t screen heater.

7-16 Maintenance
Battery lead disconnection
Caution:
1. Under no circumstances should a battery be discon nected whilst
the ignition circuit is live,
as permanent damage to the
instrument cluster may occur.
2. Disconnect the negative lead (earth terminal) first.
Fold the luggage compartment floor panel
forwards (see page 6 - 4).
Slacken the negative lead pinch bolt and
disconnect the negative (–) battery lead.
Slacken the positive lead pinch bolt and
disconnect the positive (+) battery lead. Battery lead connection
Note:
Upon battery reconnection the
security system will be armed. Opening
any protected entry will sound the alarm.
Make sure that a key or key transmitter is
available.
Caution: Do not overtighten the
pinch bolts.
Clean the battery posts and coat the post
bases with petroleum jelly.
Connect the positive (+) lead, tighten the
pinch bolt and clip the positive terminal
cover on the battery. Connect the
negative (–) lead and tighten the pinch
bolt.
After the battery ha s been reconnected
and the ignition swit ch is turned to
position ‘II’, the message centre display,
if fitted, will initially show an erroneous
reading i.e.––––––. Thiswill remain
until after the bulb check sequence, when
the correct recorded mileage will be
displayed. This is a normal function of the
instrument cluster.
After battery reconnection
After reconnecting the battery:
• Reset the electric parkbrake; refer to Parkbrake on page 4 - 34. • Reset the electrically operated
windows anti-trap function; refer to
Window Anti-trap Protection on
page 4 - 30.
• The trip computer will lose all recorded trip data and all trip
functions will be reset to zero.
The vehicle total odometer reading is
retained.
• If the battery is disconnected for more than 72 hours the radio preset
channels will need to be reset.
• Where fitted, the TV preset channels may need to be reset. Refer to the
Jaguar Touch-screen Handbook.
• Reset the clock to the correct time.
The engine electronic control system
adapts to certain characteristics of the
vehicle. These adaptations are lost if the
battery is disconnected.
On reconnection, therefore, some slightly
abnormal drive symptoms may occur and
the vehicle may need to be driven
10 miles (16 kilometres) or more while
the control system re-adapts.