sensor JAGUAR XJ 2004 X350 / 3.G Owners Manual
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2004, Model line: XJ, Model: JAGUAR XJ 2004 X350 / 3.GPages: 227, PDF Size: 4.22 MB
Page 24 of 227
Security and Locks 2 - 9
Central locking switch
With the ignition switch in either
position ‘I’ or ‘II’ and all the doors closed
and unlocked, one press of the switch
will lock all of the doors and inhibit the
luggage compartment.
With the ignition switch in either
position ‘I’ or ‘II’ and all the doors closed
and locked, one press of the switch will
unlock all of the doors and allow access
to the luggage compartment.
If the vehicle is unlocked, press and hold
the switch for more than two seconds to
centrally lock the vehicle and close all the
windows and sunroof (if fitted). Releasing
the switch will halt the operation of the
windows and sunroof (if fitted). If the vehicle is locked, press and hold the
switch for more than two seconds to
unlock the vehicle and open all the
windows and sunroof (i
f fitted). Releasing
the switch will halt the operation of the
windows and sunroof (if fitted).
Note: All windows must be ‘taught’ to
the vehicle for this function to operate.
See Window Operation on page 4 - 29.
If the central locking switch is pressed
when the ignition switch is not in
position ‘I’ or ‘II’ the security systems
inclination and intrusion sensors (if fitted)
will not operate for one arming period.
The security LED in the fascia will flash
for 5 seconds to indicate that this has
occurred.
!WARNING:
1. Make sure that all occupants are kept clear of the windows and
sunroof aperture (if fitted).
2. When an interior door release lever is pulled, the door will
unlatch.
After using the central locking switch,
it may be necessary to press the switch
again or pull a front door interior release
lever to unlock the vehicle. Smart locking
This feature helps prevent locking the key
in the vehicle.
If a door is open or ajar and an attempt is
made to lock the doors using a front door
interior locking le
ver, all doors will
centrally lock and then centrally unlock.
If a door is open or ajar and an attempt is
made to lock the doors using a rear door
interior locking lever, only the door on
which the lever is operated will lock,
the remaining doors will remain
unlocked.
If a door, hood or luggage compartment is
open, the vehicle can only be locked from
the outside by using a key in the driver’s
door lock.
Note: An audible and/or visual error
warning will be given.
It will not be possible to lock the vehicle
with a key transmitter if a door, luggage
compartment or hood is open, or a key is
left in the ignition.
Page 30 of 227
Security and Locks 2 - 15
2. If the vehicle alarm system is armed and the luggage compartment is
opened using the key transmitter,
the alarm will not sound. The system
will be rearmed when the lid is closed,
provided the vehicle has not been
disarmed.
3. Neither the luggage compartment lid release switch on the fascia
switchpack nor the lid release button
will operate when the vehicle is
armed, or in valet mode. An attempt
to operate these switches whilst in
valet mode will result in an audible
warning chime.
4. Operating the inte rnal, external or
remote luggage compartment switches
more than 15 times within
20 seconds, or opening and closing
the luggage compartment will cause
opening to be inhibited for
20 seconds. Should this happen wait
20 seconds for normal operation to
resume. If required, the luggage
compartment may be opened by using
the key during the 20 second waiting
period.Alarms and Audible
Signals
Note: In certain markets, legislation
prohibits the use of audible confirmation
signals. In such cases, the sound source
has been removed from the system.
Audible Signals
Two audible signals will be heard
(if enabled) if an atte mpt is made to lock
the vehicle with a key in the drivers door
lock or the lock button is pressed on the
key transmitter if a door, the hood or the
luggage compartment is not fully closed
or, a key is in the ignition switch.
If the vehicle is unlocked with a key when
it is armed, the vehicle will disarm,
the direction indicators will flash twice
and two audible tones will be heard
(if enabled).
The full alarm will activate, as previously
described, unless the security system is
disarmed, either by pressing the unlock
button on the key tr ansmitter, or by
placing a key into the ignition switch and
turning the key to position ‘II’.
Full Alarm
Once armed, any of the following
circumstances will create a full alarm
state, sound the horns, sound the siren,
or a combination of both (as regional
legislation dictates) and flash the
direction indicators:
• Opening a door, luggage compartment lid (except with
transmitter) or hood.
• Movement in the passenger area (if intrusion sensors are fitted).
• Using a key in the ignition switch which is not programmed to the
vehicle.
• One press of the headlamp convenience button will switch on the
headlamps for 25 seconds or until the
button is pressed again, or until a key
is inserted in the ignition switch.
See Headlight convenience on
page 4 - 24 for more details.
• An attempt to lift, or tow the vehicle (when inclination sensor fitted).
• The vehicle battery is disconnected and the vehicle is fitted with a Battery
Backed Sounder (onl y Battery Backed
Sounder will be audible).
Page 31 of 227
2 - 16 Security and Locks
• If, after 15 seconds (passively armed), from opening the driv er’s door with a
key (as regional legislation dictates),
the key is not inserted into the
ignition switch and turned to
position ‘II’, or a passenger door is
opened before the drivers door.
• Any attempt is made to remove the radio or the front navigation system
(if fitted).
• Pressing the headlamp convenience button on the remo te transmitter
3 times within 3 seconds activates the
panic alarm (if enabled).
Error Audible Signal
Two audible signals will be heard
whenever one of the following conditions
are present:
• I f a n y d o o r i s o p e n w h e n a n a t t e m p t i s made to lock the vehicle.
• The luggage compartment or the hood is not properly closed when an
attempt is made to lock the vehicle.
• A key is present in the ignition switch and a button on the key transmitter is
pressed. See
Direction Indicator Unlock Alerts
on page 2 - 11 for the Notes regarding
error signals during failure of intrusion
sensor (if fitted), and inclination sensor
(if fitted).
Note: The error audible signal can be
disabled and the direction indicator flash
option can be enabled (and vice versa) by
a Jaguar Retailer.
Error Flash Signal (Retailer
Enable Option)
The direction indicators will flash seven
times whenever one of the following
conditions are present.
• If any door is open when an attempt is made to lock the vehicle.
• The luggage compar tment or hood are
not fully closed when an attempt is
made to lock the vehicle.
• A key is present in the ignition switch and a button on the key transm itter is
pressed.
See Direction Indicator Unlock Alerts
on page 2 - 11 for the Notes regarding
error signals during failure of intrusion
sensor (if fitted), and inclination sensor
(if fitted).
Audible Signals
An audible signal will sound when:
• The valet switch is pressed with the luggage compartment closed.
• The vehicle is in valet mode and the interior/luggage compartment release
button, or glove compartment valet
switch is pressed.
• The vehicle is locked (if enabled).
• The vehicle is unlocked (if enabled).
• A door is opened if the vehicle has been passively armed. This mode can
be cancelled by disa rming the security
system using the key transmitter,
or by switching the ignition to
position ‘II’, or by turning a key in the
driver’s door lock towards the front of
the vehicle.
• The lock button is pressed twice within three seconds (if enabled).
Page 48 of 227
Before Driving 3 - 9
Interior Rear View Mirror
The interior rear view mirror is of the
electrochromic type but electrochromic
operation may be switched on or off at
the mirror.
When switched on, the mirror darkens
automatically to prevent glare from a
following vehicle’s headlamps, and clears
when light levels return to normal or
when reverse gear is selected.
Electrochromic door mirrors are operated
in conjunction with the interior mirror by
the same buttons an d function in the
same manner.
Note:
1. Should a mirror assembly become detached from the windscreen, it must
be refitted by a Jaguar Retailer.
2. Ensure that the windscreen in front of the mirror is kept clean. Where fitted,
the moisture sensor for wiper
operation is located to the front of the
mirror casing. Any dirt may affect the
operation of this sensor. Electronic road toll systems
If you have an E-ZPass or other electronic
road toll transponder, it is advisable to
mount the transmitter
on the windscreen
about 1 inch (2.5 cm) from the mirror
mount and headlining and to the side of
the mirror ensuring that it does not cover
the forward-facing light sensor. This also
keeps it away from any metal which may
affect it’s operation.
Do not move the tag more often than
need be as it can affect the calibration of
the compass.
Electrochromic operation
To switch on, press the MIRROR button.
An LED lights up to indicate that
automatic operation is selected.
Press again to switch off. Compass operation
When switched on, the compass display
on the right-hand side of the mirror
surface shows the direction the vehicle is
pointing. Eight main directions can be
displayed, e.g. ‘N’ for north, ‘SW’ for
south west.
To switch on:
Press the COMP button.
Press again to switch off.
Page 54 of 227
Before Driving 3 - 15
Various sensors determine the direction
and severity of an impact and the
presence and position of front seat
occupants.
The system analyses this information then
deploys the appropriate air bags only
e.g. the side air bags where the impact is
on that side only.
Air bags are not deployed in a rear
impact.
Air bag deployment
To do their life-saving job, air bags must
inflate rapidly and with considerable
force. There is therefore a risk of death or
serious injuries such as fractures, facial
and eye injuries or internal injuries,
particularly to occupants who are not
properly restrained by seats belt or sitting
correctly when the air bag deploys.
The risk of injury fr om a deploying air bag
is greatest close to the trim covering the
air bag.
The whole sequence of events from
sensing the impact to full inflation of the
bag takes place in a fraction of a second.
The noise and gas associated with the
deployment of the air bags is not
injurious to health. After air bag deployme
nt, it is normal to
notice a smoke-like, powdery residue or
smell the burnt propellant. This may
consist of cornstarch, talcum powder or
sodium compounds that result from the
combustion process that inflates the air
bag.
Small amounts of other chemicals may be
present which may irri tate the skin and
eyes, but none of the residue is toxic.
While the system is designed to help
reduce serious injuries, it may also cause
minor burns, abrasions, swelling or
temporary hearing loss.
!WARNING:
1. No objects whatso ever should be
attached to the centre cover of the
steering wheel, the passenger
fascia panel, the sides of the front
seats or the interior trim
immediately above the door
openings. Do not put anything on
or over the air bag inflation area.
Placing objects on or over the air
bag inflation area may cause those
objects to be propelled by the air
bag into your face and torso
causing serious injury. 2. Safety experts recommend a
minimum distance of at least
10 inches (25.4 cm) between an
occupant’s chest and a front air
bag.
3. Children 12 years old and younger can be killed or seriously injured
by the air bag. The rear seat is the
safest place for children.
4. Do not try to put an adult seat belt around two children.
5. Several air bag system components get hot after inflation.
Do not touch them after they have
deployed.
6. If an air bag is inflated, the air bag will not function again and must
be renewed immediately.
If a new air bag is not fitted,
the unrepaired area will increase
the risk of injury in a collision.
Page 56 of 227
Before Driving 3 - 17
Occupancy sensing
The front passenger seat is monitored by ultra-sonic sensors
(shown above) and a seat weight sensor to determine the
presence, weight and position of the front passenger. In certain
conditions, e.g. where no passenger is present, the appropriate
air bags will be deactivated. In a collision these air bags would
not be deployed. Note:
The occupancy sensing system is designed to confirm that
a front passenger is properly seated as recommended:
• Always sit centrally in the seat, remaining in contact with the seat back which for comfort should be rearwards of the
vertical position.
• Adjust the seat to be as far back from the fascia as practical.
• Always wear seatbelts.
The seat adjustment controls are described on page 3 - 3.
!WARNING:
It is important that the passenger position sensors
(see illustration) are not obscured in any way which could
affect air bag deployment, e.g. fitting non-approved
accessories.
Page 92 of 227
On the Road 4 - 21
CRUISE
ENGAGED None None Displayed when cruise control system is operating.
CRUISE
CANCELLED None None Driver has cancelled cruise control or is braking.
CRUISE
OVERRIDE None None Driver is pressing the accelerator pedal.
The following messages only apply to vehi cles fitted with adaptive cruise control.
DRIVER
INTERVENE Red Action by the driver to ap
ply the brakes is required.
SETSPEED
XXX MPH (or km/h) None Speed set for adaptive cruise control.
GAP None Set the distance (time gap).
ACC SENSOR BLOCKED Amber Clean the front of the vehicle in the area of the sensor unit (the sensor is mounted
behind the left-hand cover in the lower cooling air inlet).
Message
Warning
Light Priority
Indicator Meaning
Page 94 of 227
On the Road 4 - 23
Exterior Lighting
Master Lighting Rotary Switch
Positions
• OFF.
• Side (parking) lights.
• Headlights.
• Autolamps/exit delay.
!WARNING:
It is an offence in certain countries to
obscure front and rear lights,
direction indicators and reflectors. The exterior lights ar
e controlled by the
left-hand column stalk switch.
The rotary collar on the stalk has three
positions for turning th e exterior lights on
or off and positions for autolamps/exit
delay. These are:
OFF – All exterior lights OFF (except
vehicles provided with daylight running
lights).
Sidelights – Switches on front sidelights,
tail, number plate an d any other marker
lights required by local legislation.
When the external lights are ON the
instruments will also be lit.
Headlights – With the ignition in
position ‘II’, this position switches on
dipped headlights in addition to the lights
switched on in sidelight position.
The left-hand column stalk switch has
two positions for controlling the main
beam.
Pulling the switch towards the steering
wheel and releasing causes the main
beam to flash on and off. The main beam
can be flashed at any time when the
switch is pulled and will remain ON for
as long as the switch is held. The second position is to switch main
beam headlights ON. With the ignition in
position ‘II’, first select dipped beam
lights, and then push the column light
switch away from the steering wheel.
The blue warning light on the instrument
cluster and main be
am headlights will
come ON.
To turn main beam OFF, pull the column
switch towards the steering wheel to
return to dipped beam.
Note: If dipped beam is switched OFF
with main beam stil l activated, both
dipped and main beam will be
extinguished. Both dipped and main
beam will illuminate if dipped is turned on
again.
Autolamps – A light sensor control,
mounted on the front of the fascia,
monitors exterior light levels and
automatically switches the sidelights and
dipped headlights ON or OFF.
The ignition switch must be in
position ‘II’ and AUTO selected on the
stalk switch for full automatic light
operation.
When light fades towards dusk,
the sidelights and headlights will switch
ON automatically and the sidelight
warning light in the instrument cluster
will illuminate.
Page 95 of 227
4-24 On the Road
At dawn, as light increases, the sidelights
and headlights switch OFF automatically.
Do not cover the sensor and keep the
windscreen clean. Obstructing the light in
this area of the sensor may lead to
unwanted operation of the sidelights and
headlights.
Note:If the windscreen wipers are
switched on in auto, slow or fast modes
for more than 20 seconds then the
exterior lights will be switched on,
if selected to autolamps mode. The lights
will switch off 2 minutes after the wipers
are switched off or will go off straight
away if autolamps is deselected or the
ignition is turned off.
Exit delay
When parking the car at night, if the
headlights were switched on then they
will remain on for a short period after the
key has been removed from the ignition
switch. This is to give a clearly lit area for
occupants leaving the vehicle.
If the light switch rotary collar is in the
AUTO position there will be no exit delay
and the headlights will turn off when the
light switch is turned off. Three settings on the rotary collar set the
time that the lights will remain on after
the key is removed from the ignition
switch;
•10seconds.
•30seconds.
•2minutes.
Note:
The key must not be in the ignition
switch for this feature to operate.
The message centre shows the delay
setting or when this feature is turned off.
Headlight convenience
When approaching the vehicle,
the sidelights and headlights can be
switched on by pressing the headlight
button on the re mote transmitter.
The lights will come on for 25 seconds or
can be switched off by pressing the
remote transmitte r headlight button
again. Daylight running lights
In certain countries it is a legal
requirement for the lights to be on during
the hours of daylight.
With the rotary co
llar in the OFF
position, dipped headlights, sidelights,
tail lights, number plate lights and side
marker lights will switch on automatically
with the following conditions:
• The ignition is turned to position ‘II’.
• The vehicle gear se lector out of park.
• The parkbrake is not applied (released).
Page 97 of 227
4-26 On the Road
Direction Indicators
The direction indicators, the left column
stalk, operate when the ignition is in
position ‘II’. Move the stalk up for
indicating a right turn or move it down to
indicate a left turn.
Two positions are provided. The first
position, partly moving the stalk up or
down, causes the indicator to flash while
it is held in this position. On releasing the
stalk the indicators stop flashing.
The second position is a full movement of
the stalk up or down, which can then be
released. The indicators will remain
flashing and will cancel when the turn is
completed. An audible ticking an
d a flashing green
arrow on the instrument cluster indicates
that the selected direction indicator is
operating.
Bulb failure
The direction indicators (including those
on a trailer, if attached) and side
repeaters are monitored for bulb failure.
If a bulb fails when it is on, a message is
shown in the message centre. At the same
time, the corresponding side green
warning light will flash at twice the
normal rate. The audible ticking will
sound at twice the normal rate.Door Guard/Puddle Lights
Door guard lights are fitted to each door
to give warning of an open door to
passing vehicles.
Puddle lights illuminate the ‘step out’
area at night.
Each light comes on automatically when
the door is opened. If the door is left
open the lights remain on for 5 minutes
and then switch off.
Approach Lights
Approach lights are fitted in the door
mirrors to provide illumination for the
floor area around the front doors.
The approach lights come on when:
• The vehicle is unlocked using a key, key transmitter or the central locking
switch.
• Using the headlight convenience button on the key transmitter.
• Reverse gear is selected.
The approach lights will not illuminate if
the autolamp sensor determines that the
ambient light is sufficiently bright.
Luggage Compartment
Lighting
The luggage compar tment will be
illuminated when the lid is opened.
Glove Compartment
The glove compartment will be
illuminated when the lid is opened.