JAGUAR XJ 2013 X351 / 4.G Quick Start Guide

SOME OF THE FEATURES DESCRIBED MAY NOT APPLY TO YOUR VEHICLE
XJ
QUICK START GUIDE
DRIVER CONTROLS 2
VEHICLE ACCESS 3
COMFORT ADJUSTMENTS 4
STARTING AND DRIVING 5
DRIVING AIDS 8
TOUCH SCREEN AND AUDIO 10
HEATING AND VENTILATION 13
NAVIGATION 14
TELEPHONE 15
GAS STATION INFORMATION 16

JAGUAR XJ JAGUAR XJ JAGUAR XJ
2
Driver controls
Headlamps, direction indicators and trip computer1.
Manual gear change paddle (-) down2.
Instrument panel, warning lamps, message center 3. and turn by turn navigation
Manual gear change paddle (+) up4.
Wiper and Washers5.
STOP/START6.
Sunroof control 7.
Parking aid8.
Rear screen sun blind9.
Sunroof blinds10.
Interior lamps11.
Audio system12.
Climate control13.
Windshield heater14.
Rear screen heater15.
Gear selector 16.
Dynamic Stability Control (DSC) switch17.
Automatic speed limiter (ASL) switch18.
Electronic Parking Brake (EPB)19.
Dynamic mode switch20.
Winter mode switch21.
Instrument panel menu control22.
Adaptive cruise control gap setting and cruise control 23. cancel
Cruise control24.
Steering column adjustment25.
Telephone controls26.
Heated steering wheel27.
Audio/video menu control28.
Instruments dimmer control29.
Rear Fog lamps30.
Trunk release31.
Central locking switches32.
Hazard warning33.
Touch screen Home menu34.
Telephone menu 35.
Navigation menu36.
Intellient stop/start37.
Heated front seats menu38.
Audio settings menu39.
Audio/video menu40.
CD/DVD eject41.
Audio/video sources42.
Rear window isolator43.
Window controls44.
Power folding mirror selectors and adjuster45.
Driving position memory store controls46.
22/05/2012 14:13:2622/05/2012 14:13:2622/05/2012 14:13:26

JAGUAR XJ JAGUAR XJ JAGUAR XJ
3
Vehicle access
Unlocking mode alternatives
Single-point entry allows only the driver’s door to unlock with a single press. A second press unlocks all other doors and the luggage area.
Multi-point entry will unlock all doors and luggage area with a single press.
To change between modes, with the vehicle unlocked, press the lock and unlock buttons simultaneously for three seconds. The hazard warning lamps will flash twice to confirm the change. Mode change can also be made via the instrument panel menu control.
Smart Key Smart Key
Keyless entry/exit Keyless entry/exit
Press once to lock the vehicle and arm only the exterior alarm.
Multi-point entry - Press once to disarm the alarm, unlock all doors and unlock the trunk.
Press and hold to unlock all doors and open the windows (Global opening).
Press once to switch the headlamps on for 25 seconds. Press again to switch off.
Press to open only the trunk. The rest of the security system remains active.
Press and hold for 3 seconds to activate/cancel the panic alarm.
To unlock the vehicle and disarm the alarm first ensure that the Smart Key is outside the vehicle but within 3 ft (1 m).
Press a door handle button or trunk release button.
To lock the vehicle and arm the alarm first ensure that the Smart Key is outside the vehicle but within 3 ft (1 metre).
Press a door handle button once to single lock.
Operating note
If the Smart Key fails to operate, hold it against the facia below the auxiliary switch pack. Start the engine as normal (see page 5). The Smart Key can now be removed.
Care point
The Smart Key may not be detected if it is placed within a metal container or if it is shielded by a device with a back lit LCD screen, (e.g. laptop, smartphone etc.) Keep the Smart Key clear of such devices when attempting Keyless entry or Keyless starting.
Do not leave your Smart Key inside the trunk; the vehicle WILL NOT automatically unlock (should it become shielded).
Emergency key release
Slide the side section up to remove. Remove the keyblade and unfold it. Use the blade to release the front left-hand door lock cover.
Insert the key into the exposed lock and turn towards the front of the vehicle, then release it to unlock.
If the security system was previously armed with the Smart Key, when the door is unlocked the alarm will sound. To disarm the alarm, press the unlock button on the Smart Key or press the START/STOP button with the Smart Key inside the vehicle.

JAGUAR XJ JAGUAR XJ JAGUAR XJ
Setting the driving position Setting the driving position See page 2, items See page 2, items 25 and 46and 46and
Restraints
Comfort adjustments
4
Driver’s seat
Set the seat position using the following controls.
Seat forwards and back, cushion height and cushion 1. angle.
Cushion length.2.
Side bolster - inflate.3.
Side bolster - deflate.4.
Lumbar support.5.
Seat back angle and head restraint. 6.
Steering column
With the vehicle stationary, adjust the steering column 7. to the required driving position.
Door mirrors
1. Press the left or right mirror selector.
2. Use the mirror adjuster to set mirror position.
Storing the driving position to memory
When the driver’s seat, steering column and door mirrors are adjusted to the required position, the settings can be stored.
1. Press the M button to activate the memory store function. The button will illuminate to indicate the memory store function is active.
2. Press button 1, 2 or 3 to store the current driving position to the chosen number.
Use a stored memory position by pressing the appropriate button; 1, 2 or 3. The seat, steering wheel and mirrors will move to their preset positions.
Operating note
Memory buttons 1, 2 or 3 must be pressed within 5 seconds after pressing the M button otherwise the memory store function will cancel.
A warning indicator on the instrument panel will illuminate if the seat belt of an occupied front seat is not fastened. This may be accompanied by an audible warning.
Using child seats
Refer to Child Seat Positioning in the Owner’s Handbook to determine the correct seat for your child.
If it becomes necessary to fit a child restraint on the front passenger seat, make the following seat adjustments.
Move the seat fully rearward.•
Lumbar support to minimum setting.•
Seat cushion to highest position.•
Cushion front tilt to lowest position.•
Seat back to upright position.•
Adjust the upper seat belt anchorage to its lowest • position.
When a front passenger seat occupancy sensor is fitted it determines the state of seat occupancy and sets the airbag status to suit. The status indicator is in the overhead console.
Seat unoccupied - air bag deactivated and indicator • off.
Seat occupied - air bag activated and indicator off.•
Low weight occupant or object - air bag deactivated • and indicator on.
1
2
3456
7
22/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:2722/05/2012 14:13:27

JAGUAR XJ JAGUAR XJ JAGUAR XJ
Engine start/stop Engine start/stop See page 2, item See page 2, item 6
Starting and driving
5
Operating note
The engine will continue to run even if the Smart Key is removed from the vehicle by more than 3 ft (1 m). However, if the engine is stopped, it cannot be restarted until the Smart Key is returned to the vehicle.
Ignition only on:
With the Smart Key inside the vehicle, press the • START/STOP button to switch on ignition.
A second press will switch off the ignition.•
Engine start
The selector lever must be in • Park or Neutral position to enable engine starting.
With the foot brake depressed, press and release the • START/STOP button to start the engine.
Press again to stop the engine and switch off the • ignition.

Rolling start
If the engine is switched off while the vehicle is moving, it can be restarted by selecting N position then pressing the START/STOP button.
Virtual instrument panel Virtual instrument panel
Main Menu
Display settings Trip computer
Ve
hicle set-up
Show warnings
Service MenuDriver information is displayed on a TFT Virtual Instrument Panel.
Many features of the display can be changed to suit personal preferences. Other features, such as the speedometer, can be altered to suit the driving situation. The speedometer can be configured for KPH or MPH via the Vehicle Settings menu.
To access the main menu in the instrument panel, press any button on the right side steering wheel control. Use the direction controls to move through the menu and subsequent options. Press OK to confirm your selections.
The stop/start system is automatically activated when the ignition is turned on. If the vehicle is stopped, the engine will turn off (unless it is required to support other vehicle systems). When the brake is released and a drive gear is selected the engine will restart automatically.
A warning lamp on the instrument panel will illuminate when the engine has been switched off by the stop/start system.
Intelligent stop/start Intelligent stop/start See page 2, item See page 2, item 37
To switch the system off, • press the Eco switch.
Note: The engine will restart Note: The engine will restart Note:automatically if the switch is pressed whilst an automatic engine stop is in progress.
JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 5JJM189634131.indd 522/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:2822/05/2012 14:13:28

JAGUAR XJ JAGUAR XJ JAGUAR XJ
Warning lamps Warning lamps Displayed on the instrument panelDisplayed on the instrument panel
Transmission See page 2, item See page 2, item 2, 4 2, 4 and 16and 16and
Electronic parking brake Electronic parking brake See page 2, item See page 2, item 19
Starting and driving
6
Select P before switching off the engine. However, if the engine is switched off with Reverse, Drive or Sport selected, the selector will automatically return to P while retracting.
Low tire pressure
Braking system fault or brake fluid low
Braking system fault or brake fluid low. USA onlyElectric parking brake is applied. Flashing - EPB fault. USA only Electric parking brake is applied. Flashing - EPB fault.
Seat belt reminder
Forward alert active
Automatic speed limiter active
Adaptive cruise control active in follow mode
Dynamic stability control fault. Flashes when DSC is operatingAnti-lock braking system fault.
Anti-lock braking system fault. USA only
Engine/transmission malfunction
DSC switched off, Trac DSC on
Air bag fault
Gearshift interlock
Apply the foot brake then move the selector from the Park position. Maintain brake pressure until a gear is selected.
Automatic gear selection
Select D for fully automatic gear changes.
Sport mode
This is an automatic gear change mode, however, change points are modified to make full use of engine power.
Press the selector down and rotate from D to Sport.
Manual gear changes
Manual gear change mode is effective when rapid acceleration and engine braking are required.
To shift down, briefly pull the left (-) paddle.•
To shift up, briefly pull the right (+) paddle.•
When the paddles are used in D, gear selection will revert to automatic if use of the paddles is not maintained. With S selected, continuous manual operation is initiated if the paddles are used.
To return to automatic operation pull and hold the right hand paddle for 2 seconds.
Operating note
If the engine is switched off with Neutral selected, automatic selection of P is delayed for 10 minutes. DONOTuse this feature to enable towing of the vehicle. Refer to Vehicle recovery in the Owner’s Handbook.
Releasing
With the ignition on, apply the foot brake and press • down on the parking brake lever.
If the vehicle is stationary with the parking brake • applied and either Drive or Reverse selected, pressing the accelerator will automatically release the parking brake.
Applying
With the vehicle stationary, lift up the parking brake • lever and then release it. The red warning lamp in the instrument panel will illuminate.
22/05/2012 14:13:2922/05/2012 14:13:2922/05/2012 14:13:29

JAGUAR XJ JAGUAR XJ JAGUAR XJ
Setting cruise control speed
Press to set cruise control 1. at the current speed.
Resumes the set speed 2. after a cancellation.
Press to decrease set 3. speed until the desired new speed is reached.
Press to cancel.4.
Auto headlamps and wipers Auto headlamps and wipers See page 2, items See page 2, items 1 and 5and 5and
Cruise control and forward alert See page 2, items See page 2, items 23 and 24and 24and
Starting and driving
7
For automatic wipe activated by the rain sensor, move the wiper control up to the first position. Sensitivity can be adjusted.
5. First stop for auto position.
6. Rain sensor maximum sensitivity.
7. Rain sensor minimum sensitivity.
Care point
Before entering an automatic car wash, turn the wipers off to deactivate the rain sensor. Otherwise, the wipers will operate during the washing process and may be damaged.
ACC gap setting
5, 6. Press to increase or decrease the set gap to the vehicle ahead.
4. Press to cancel ACC and the set speed.
When ACC is active an amber warning lamp will illuminate in the instrument panel. Set speeds are cleared at ignition off.
Forward alert
An additional feature of ACC, forward alert provides limited detection of objects in the road ahead. When necessary it will give an audible warning plus the visual warning ‘FORWARDALERT’ in the message center. The driver must take appropriate action.
See the Owner’s Handbook for full details.
1
432
MA X
MIN
MAX
MIN
6
5
7
When lighting control 1. AUTO is selected, side lamps and headlamps will turn on automatically as ambient light fades.
With the control in the low beam position, high beam will activate automatically when ambient light falls below a pre set level. Vehicle speed must be above 25 mph (40 km/h).
2, 3, 4. The headlamps can temporarily illuminate ahead when exiting the car at night. Rotate the control for delay periods of 30, 60 or 120 seconds.
1
2
34
5
4
6
Cruise control override
Cruise control will disengage if the brake pedal is pressed or when vehicle speed falls below 30 km/h (18 mph).
Adaptive cruise control (ACC)
This enhancement uses a front mounted radar to monitor traffic ahead. ACC can be programmed to maintain a set gap to the vehicle ahead. If the vehicle ahead is travelling slower than the set cruise control speed, your vehicle will automatically slow down and then maintain the set gap until the road ahead clears. At that point your vehicle will accelerate to the set cruise control speed.

JAGUAR XJ JAGUAR XJ JAGUAR XJ
Automatic speed limiter (ASL) Automatic speed limiter (ASL) See page 2, items See page 2, items 18 and 24and 24and
Instrument panel Instrument panel See page 2, items See page 2, items 1, 3 1, 3 and 22and 22and 22 22
Driving aids
ASL allows any speed between 18 and 150 mph (30 and 240 km/h) to be set as a maximum speed. This is useful to ensure any road speed limit is not exceeded.
Setting a speed
The setting procedure can be made while the vehicle is stationary.
Press the ASL button. An ASL 1.warning lamp illuminates in the speedometer.
Use the cruise control + and - 2.controls to set a speed. The message center will display the set speed. Adjustment can be made at any time to suit variable speed limits.
If ASL is cancelled due to kick down acceleration or by pressing the cruise control CAN, the message center will display a ‘LIMITERCANCELLED’ message.
Press the RES control to reinstate the ASL set speed.
Message center
Messages are displayed within the tachometer dial and may be accompanied by an icon. If more than one message is active then each will be displayed in turn.
Turn by turn navigation
When a destination is set on the navigation touch screen and guidance is commenced, a simplified graphic guide is displayed in the instrument panel. It gives turn by turn information about the next part of the journey.
Trip computer
Trip computer information can be accessed via the TRIP button on the end of the lighting control. Information is displayed in the instrument panel left side dial.
Press the TRIP button repeatedly to display data in the following order:
Odometer•
Trip distance since trip reset•
Average speed since start of trip•
Average fuel consumption since trip reset•
Remaining range estimate based on current fuel • consumption.
Three trip memories are available via the right side steering wheel control. Trip A and B can be reset to zero with a long press of the TRIP button. Auto will reset to zero after each ignition cycle.
8
Operating note
When negotiating a steep downhill gradient, vehicle speed may exceed the set speed. The message center will display a warning. Driver intervention may be required to reduce speed.
2588kmOdo237kmRange
2.30pm 23°C
CD 2Groove Armada
Tr
3/15 Mix CD
02:32
Text line 1
Te xt line 2
Press OK
to hide message
A423 Wa rwick Road

JAGUAR XJ JAGUAR XJ JAGUAR XJ
JaguarDrive control JaguarDrive control See page 2, items See page 2, items 17, 20 17, 20 and 21and 21and
Parking aids Parking aids
Blind spot monitoring Blind spot monitoring
Driving aids
9
When Reverse is selected, the rear and front parking aids and rear camera will activate.
The touch screen will display a vehicle graphic and indicate the approximate distance to any object detected. An audible alert will increase in frequency as the object is approached.
When moving forward into a space, activate the front sensors with the parking aid switch in the overhead panel. Alternatively, select R then Drive.
Audible alert volume can be adjusted via the touch screen. Select the Home menu then Setup followed by System. Now select Volume presets. Use the + or -soft keys alongside Parking aid to adjust volume.
Cancelling the parking aid screen
Touch the screen to return to the previous view.
Rear camera
Activates when Reverse is selected. Guidance lines to aid reversing appear on the touch screen.
The camera is deactivated when Drive is selected and vehicle speed exceeds 10 mph (16 km/h).
Winter mode, Dynamic mode and Dynamic Stability Control (DSC) allow the driver to more finely tune the vehicle driving characteristics to suit prevailing conditions.
Winter mode. Use in slippery road conditions. Selects 1. 2nd gear for driving away, moderates engine response and modifies gear change strategy to ensure maximum possible traction is achieved.
Dynamic mode. Delivers a high performance driving 2. experience. If Sport mode is now used with paddle gear selection, there is no automatic gear change, even if the rev limit is reached.
DSC. The default condition at engine start is DSC 3. on and is designed to control vehicle stability. TracDSC is an alternative setting that optimises the DSC settings for maximum traction in difficult conditions. To select TracDSC, depress the DSC switch for less than 10 seconds. Touch the switch again to return to DSC. To turn DSC off, depress the switch for more than 10 seconds.
1
2
3
Each mirror displays amber icons to warn of overtaking vehicles in adjacent lanes. The monitored area extends approximately 20 ft (6 meters) behind the rear wheels and 8.2 ft (2.5 meters) to the sides.
It switches on automatically at speeds above 10 mph (16km/h) while in a forward gear.
JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 9JJM189634131.indd 922/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:3122/05/2012 14:13:31

JAGUAR XJ JAGUAR XJ JAGUAR XJ
Home menu
Touch screen and audio
Destination entry8. . Touch for direct access to the Destination entry menu.
Climate.9. Secondary controls menu. Climate control primary settings are made from the hard controls below the touch screen.
AV.10. Hard key selection of the audio/video sources menu.
Displays the 11. Home menu.
PHONE.12. For Phone settings, Digit Dial, Phonebook and Last 10 numbers dialled.
N AV13. . Hard key selection of the navigation options menu.
Audio tone and balance settings. 14.
The touch screen requires only light touches. Excess pressure could result in damage.
10
Valet1. . Select valet mode to lock the trunk and glove box when using attendant parking. When returning to the vehicle, touch Valet again and follow the on-screen instructions.
Setup.2. Personalize screen view, system settings, voice and volume presets.
Audio settings3. . Tone, balance and fade.
Phone4. . Phone menu.
Shortcut soft keys. Up to 2 personal shortcuts can be 5. set to quickly access any available part of the system. Shortcuts are made in the Setup menu.
Audio/Video.6. Select any of the audio and video sources, set personal preferences and store stations to pre-sets.
N a v.7. On the first navigation screen, touch Agree to move to the main menu or select Language if you need to select a different navigation language.
Operating note
Always run the engine during prolonged use of the touch screen.
Steering wheel control Steering wheel control See page 2, item See page 2, item 28
Short press to move to next available audio or video source. Long press to 1. scroll through sub menu of selected source.
Press to increase volume.2.
Press to decrease volume.3.
Short press to select next radio preset station or next CD/MP3 track. Long 4. press to search up for the next radio station or to advance through the CD/MP3 tracks.
Has the same action as 5. 4 but moves in the opposite direction.
1
54
2
3