radio JAGUAR XJ6 1994 2.G User Guide

15.8 IN - CAR ENTERTAINMENT (ICE)
0
1. Radio/Cassette Unit
2. Auto Changer
Fig.
1
3 Door Speakers
4. Tweeters
'5.8.1 General Description
The plan view in Fig.1 shows the locations of the In-Car Entertainment (ICE) equipment. This consists of a radio cas- sette playerfitted inside an aperture ofthecentreconsole switch assembly, a compact disc auto-changer located inside
the trunk, four speakers fitted to the front and rear doors and four tweeters of which two are located on either side of
the crash
- roll dash below the windscreen and two on either side of the rear shelf.
The vehicle has an electrically operated, retractable aerial fitted on the offside rear fender.
X300 VSM 19 Issue 1 August 1994

Clear
(amps) 1
Circuit
I
25 5 Power amplifier - radio / cassette and compact disc player (where
fitted)
Tail lamp
- left-hand side
Number plate lamp
- left-hand side I Back-up lights
Stop lamp
- left-hand side
Turn indicator
- rear left-hand side
F3 Light Blue
F4 Red 10 Security system
F5 Red 10 Body processor unit (BPU)
F6 Tan 5 Data link connector
F7 Light Green 30 Fuel pump
F8 Light Blue 15 Luggage compartment remote release
F9 Light Blue 15 i Rear fog guard lamps
Radio
telephone (where fitted)
1
Aerial, Radio /cassette and compact disc player memory feed.
Stop lamp
- right-hand side
1 Turn indicator - rear right-hand side I.
I FIO Tan 5 i Radio / cassette and compact disc player control relay
F11 Clear 25 1 Caravan /Trailer module I
t F12 Tan 5 ~ Accessories
and telephone control relay I I
I I I F13 Red 10 ~ Accessories 1 1 I I F14 - - I Not used 1 I I F15 Clear 25 1 Heated
rear window I I I F16 Tan 5 1 Airbag warning
Luggage Compartment Fuse Box
Issue 1 August 1994 AI-95MY 18 X300 VSM
L F18 Tan 5 Tail lamp - right-hand side
License plate lamp - right-hand side

Security System - RESTRICTED /SSUE 84
-
Uo feature
A5.5 HOW TO OPERATE THE SYSTEM
Deadlock all doors, lock
trunk lid and fuel filler cap.
Arm the alarm system
(perimeter, inclination and
intrusion). Close open win
-
dows and sliding roof.
Once deadlocking is com
-
pleted, the sounder gives
one audible tone.
Note:
No deadlock feature in Ja- panese market.
Locking, unlocking and setting the vehicle alarm system is carried out by key or by radio frequency key-ring trans- mitter.
Unlock
all other doors and
trunk lid.
- Operation of the system by key or key-ring transmitter will be described separately in this sub-section.
Key-ring transmitter functions vary slightly between market variants. The action for each variant is described separate- ly where appropriate
m: Certain functions differ due to market variations. Differences will be detailed in the the following instruction
tables. The variants are defined as follows:
No feature
A
0 Variant 1 - European and UK markets
0 Variant 2 - North American markets
0 Variant 3 - Rest of the World.
,5. 1 Locking (key)
Instruction
rurn key to lock position
and release.
rurn key to lock position,
?old for 2 seconds and re-
ease.
rurn key to unlock position
and then to lock position
Nithin 3 seconds. Hold in
ock position for
2 seconds :o close windows and slid-
ng roof.
A5.5.2 Unlocking (key)
Instruction
Turn key to unlock position
and release.
rurn key to unlock position
and hold for
2 seconds.
Variant 1
Lock all doors, trunk lid,
fuel filler cap and arm the
alarm system (perimeter
only).
Lock
all doors, trunk lid,
fuel filler cap. Arm the
alarm system (perimeter
only). Close open windows
and sliding roof.
Deadlock
all doors, lock
trunk lid and fuel filler cap.
Arm the alarm system
(perimeter, inclination and
intrusion). Close open win
-
dows and sliding roof.
Once deadlocking is com
- pleted, the sounder gives
one audible tone.
Variant 1
Unlock all doors, trunk lid,
fuel filler cap.
On variant
1 unlocking
with the key does not dis
- arm the alarm system. An
audible ticking indicates
that the alarm will activate
after 30 seconds unless
the key is turned to posi-
tion II in the ignition or the
key-ring transmitter but-
ton (small) is pressed.
No feature
rlariant 2
-ock all doors, trunk lid,
'uel filler cap and arm the alarm system.
Variant 3
Lock all doors, trunk lid,
fuel filler cap and arm the
alarm system (perimeter
only) alarms.
-ock all doors, trunk lid,
'uel filler cap. Arm the
alarm system. Close open
Nindows and sliding roof. Lock
all doors,
trunk lid,
fuel filler cap. Arm the
alarm system (perimeter
only). Close open windows
and sliding roof.
Variant 2 I Variant 3
Unlock drivers door only,
trunk lid, fuel filler cap.
Disarm the alarm system.
Switch on the interior light
for
15 seconds. Unlock
all doors, trunk lid,
fuel filler cap. Disarm the
alarm system. Switch on
the interior light for
15 sec-
onds.
X300 VSM Issue 1 August 1994 12

w:
A5.5.4 Locking (Key-ring Transmitter)
Locking is inhibited if any door is open or ajar.
nstruction
'ress large button once.
Press large button again
within
3 seconds of first
press.
Press large button for third
time within ten seconds of
previous action.
rlariant 1
-ock all doors, trunk lid, 'uel filler cap and arm the
darm system (perimeter
mly).
lirection indicators flash
mce. Warning light (cen-
:ral locking switches)
'lashes when vehicle se-
:ured.
Deadlock all doors, Arm
the alarm system (per
- imeter, inclination and in-
:rusion).
Variant 2
Security System - RESTRICTED ISSUE
A5.5.3
Each vehicle is supplied with two radio frequency transmitters, designed to be attached to the drivers key-ring. Key- ring transmitter 1 is dedicated to driving position memory 1 and key-ring transmitter 2 is dedicated to driving position
memory 2.
The key-ring transmitter is activated by pointing it towards the vehicle and pressing one of the two operating buttons;
the large button locks the vehicle and arms the alarm system, whilst the small button unlocks the vehicle and disarms
the alarm system. When either one of the buttons are pressed, an indicator light on the key-ring transmitter flashes;
red for the large button, green for the small button.
If the ignition key is left in the ignition switch the following features will be inhibited:
Locking / Unlocking (Key-ring Transmitter)
0 Alarm system
0 Remote luggage compartment release.
If the ignition key is left in the ignition switch in position 1 the remote headlamp convenience feature will be inhibited. ~~ ~
Headlamps on for 25 sec- mds.
Note:
The headlamps will also :ome on if the large but-
ton is pressed whenever
the vehicle is locked or
deadlocked. Lock
all doors,
trunk lid,
Fuel filler cap and arm the
alarm system (perimeter,
inclination and intrusion
alarms).
An audible signal will be
heard and side lights will
Flash once. Warning light
(central locking switches)
flashes when vehicle se
- cured.
Headlamps on for
25 sec- onds if vehicle previously
locked and armed.
Headlamps on for
25 sec
onds.
No Feature.
Variant 3
Lock all doors, trunk lid,
fuel filler cap and arm the
alarm system (perimeter
only).
Direction indicators flash
once. Warning light (cen
-
tral locking switches)
flashes when vehicle secu-
red.
Headlamps on for
25 sec- onds if vehicle previously
locked and armed.
Japanese Market Only:
Lock all doors, trunk lid,
fuel filler cap and arm the
alarm system.
Headlamps on for
25 sec
onds if vehicle previously
locked and armed.
Deadlock all doors, Arm
the alarm system (per
-
imeter, inclination and in- trusion).
Japanese Market Only:
Headlamps on for 25 sec- onds.
Headlamps on for
25 sec-
onds.
Japanese Market Only;
No Feature.
Issue 1 August 1994 X300 VSM 13

0 Variant 3 -Rest of the World.
A5.7.1 Locking (key)
Turn key to unlock position
and hold for 2 seconds.
nstruction I Variant 1 I Variant 2 I Variant 3
with the key does not dis-
arm the alarm system. An
audible ticking indicates
that the alarm will activate
after
30 seconds unless
the key is turned to posi
- tion II in the ignition or the
key
-ring transmitter but- ton (small) is pressed.
No feature
I I I rurn key to lock position
and release. imeter
onlv).arms.
Check that all doors, trunk lid and fuel filler cap lock and that the alarm system (per-
rurn key to lock position,
Told for 2 seconds and re-
Check that all doors, trunk lid and fuel filler cap lock,.the alarm system (perimeter
only) arms and all open windows and sliding roof close within 1.5 seconds.
ease.
rurn key to unlock position
and then to lock position
tvithin 3 seconds. Hold in
ock position for
2 seconds
:o close windows and slid- ng roof. Check
all doors
are dead-
locked and trunk lid and
fuel filler cap are locked.
Check alarm system (per
-
imeter, inclination and in- trusion) arms and all open
windows and sliding roof
close within 1.5 seconds.
Ensure that once deadlock
- ing is completed, the
sounder gives one audible
tone.
A5.7 SYSTEM TESTING
The following information details the procedures for a complete system test to identify and locate possible fault condi-
tions. Where faulty operation is identified refer to Diagnostic Sub-Routines for possible causes and remedies.
Locking, unlocking and setting the vehicle alarm system is carried out by key
or by radio frequency key-ring trans- mitter.
W:
Key-ring transmitter functions vary slightly between market variants. The action for each variant is described separate- ly where appropriate
m: Certain functions differ due to market variations. Differences will be detailed in the the following instruction
tables. The variants are defined as follows:
o Variant 1 - European and UK markets.
0 Variant 2 - North American markets.
Ensure
all doors
are fully closed before initiating lock procedures.
A5.7.2 Unlocking (key)
e Instruction Variant 1
Turn key to unlock position Check all doors, trunk lid
and release. and fuel filler cap unlock.
No feature
Variant 2
Check drivers door and
fuel filler cap unlock.
Check that the alarm
sys- tem disarms and the in-
terior light illuminates for
15 seconds.
Check all passenger doors
and trunk lid lock. Check
all doors
are dead-
locked and trunk lid and
fuel filler cap are locked.
Check alarm system (per
-
imeter, inclination and in- trusion) arms and all open
windows and sliding roof
close within 1.5 seconds.
Ensure that once deadlock
-
ing is completed, the
sounder gives one audible
tone.
Note:
No deadlock feature in Ja- panese market.
variant 3
Check all doors, trunk lid
and fuel filler cap. Check
that the alarm system dis
- arms and the interior light
illuminates for 15 seconds.
No feature
_____ X300 VSM 17 Issue 1 August 1994

Security System - RESTRICTED MU€ 84
-
A5.7.3 Locking / Unlocking (Key-ring Transmitter)
Each vehicle is supplied with two radio frequency transmitters, designed to be attached to the drivers key-ring. Key- ring transmitter 1 is dedicated to driving position memory 1 and key-ring transmitter 2 is dedicated to driving position
memory 2.
The key-ring transmitter is activated by pointing it towards the vehicle and pressing one of the two operating buttons;
the large button locks the vehicle and arms the alarm system, whilst the small button unlocks the vehicle and disarms
the alarm system. When either one of the buttons are pressed, an indicator light on the
key-ring transmitter flashes;
red for the large button, green for the small button.
If the ignition key is left in the ignition switch the following features will be inhibited:
0 Alarm system
0 Remote luggage compartment release.
If the ignition key is left in the ignition switch in position 1 the remote headlamp convenience feature will be inhibited.
A5.7.4 locking (Key-ring Transmitter)
nstruction
'ress large button once.
'ress large button again
Nithin 3 seconds of first xess.
'ress large button for third
:ime within ten seconds of
3revious action.
Variant 1
Check all doors, trunk lid
and fuel filler cap lock and
the alarm system (per
- imeter only) arms.
Ensure direction indicators
flash once and the security
active indicator flashes
when vehicle secured.
Check that headlamps are
illuminated for
25 seconds
if vehicle was previously
locked and armed and but
-
ton has not been pressed
within
4 seconds.
Check all doors are dead-
locked and the alarm sys- tem (perimeter, inclination
and intrusion) is armed.
Check headlamps illumi
-
nate for 25 seconds.
Note:
The headlamps will also il- luminate if the large but-
ton is pressed whenever
the vehicle is locked
or
deadlocked.
Variant 2
Check all doors, trunk lid
and fuel filler cap lock and
the alarm system arms.
Ensure that an audible sig
-
nal is heard, side lights
flash once. and security
active indicator flashes
when vehicle secured.
Check that headlamps
are
illuminated for 25 seconds
if vehicle was previously
locked and armed.
Check headlamps illumi
-
nate for 25 seconds.
No Feature.
Variant 3
Check all doors, trunk lid
and fuel filler cap lock and
the alarm system (per
- imeter only) arms.
Ensure direction indicators
flash once. and security
active indicator flashes
when vehicle secured.
Check that headlamps are
illuminated for
25 seconds if vehicle was previously
locked and armed.
Japanese Market Only:
Check all doors, trunk lid
and fuel filler cap lock and
the alarm system arms.
Check that headlamps
il-
luminate for 25 seconds if
vehicle was previously
locked and armed.
Check all doors are dead
-
locked and the alarm sys- tem (perimeter, inclination
and intrusion) is armed.
Japanese Marked Only:
Check headlamps illumi-
nate for 25 seconds. __ Check headlamps illumi-
nate for 25 seconds.
Japanese Marked Only:
No Feature.
X300 VSM issue 1 August 1994 18

Security System - RESTRICTED ISSUE 84
-
A5.18 REAR DOOR LOCKASS€MBLY - RENEW
SRO 86.25.47
. Remove the veneer trim pad. See Section 13 of the VSM.
. Remove the upper trim pad. See Section 13 of the VSM.
. Remove the lower trim pad. See Section 13 of the VSM.
. Using a suitable plastic knife, cut through the weathershield to door sealant and pull back the weathershield for ac-
. Cut and remove the securing tie-wrap from the door lock assembly harness multi-plug.
Displace and reposition the door lock assembly multi-plug from the mounting bracket and disconnect.
Disconnect the door handle link rod.
. Disconnect and remove the door sill button link rod.
= Undo and remove the door lock assembly securing bolts.
. Undo and remove the lower securing bolt from the glass frame.
Displace and reposition the door lock assembly into the bottom of the door.
Displace and remove the edge clip from the door handle release cable.
. Displace and reposition the door handle release cable.
9 Displace and remove the door lock assembly.
cess
to the door lock assembly.
A5.19 TRUNKLIDLOCKACTUATOR- RENEW
SRO 86.25.49
. Open the trunk lid.
. Remove the luggage compartment lamp assembly. See Section 15 of the VSM.
Displace and remove the trunk lid liner fasteners and reposition for access.
. Undo and remove actuator mounting bracket securing bolts.
Disconnect the actuator to lock mechanism link rod.
. Remove the actuator and motor.
Undo and remove the actuator to mounting bracket securing screws.
Fitting
a new actuator is the reverse of the removal procedure.
Disconnect
the actuator harness
multi-plug.
15.20 CLOCKMODULE- RENEW
SRO 86.80.13
. Remove centre console ashtray and veneer panel., refer to VSM, section 13.
. Release and remove gear selector illumination module securing screws.
. Re-position illumination module as necessary for removal of radio console.
= Release radio console securing screws, partially withdraw radio console from center console so that console harness
and radio aerial connectors can be removed.
. Release radio ground lead from securing nut.
. Remove dedicated radio harness connector from multi-plug.
. Fully withdraw radio console and remove radio unit.
Release securing screws and remove clock module.
15.21 READER EXCITER COIL AND MODULE - RENW
. Access to the reader exciter coil is gained by removing top and bottom ignition cowls, refer to VSM, Section 13 for
The exciter coil is mounted around the ignition switch and can be removed by releasing spring tension coil clips.
. The module is mounted on the steering column assembly, secured by two bolts.
. To remove the module disconnect the harness multi-plug and remove the securing bolts.
remove
/ refit instructions.
X300 VSM Issue 1 August 1994 44