air condition JEEP CHEROKEE 1988 Service Repair Manual

\0032.5 L C EC S YSTE M

1988 J e ep C hero ke e
1988 Computerized Engine Controls
JEEP 4-CYLINDER 2.5L TBI COMPUTERIZED EMISSION CONTROL
Cherokee, Comanche
DESCRIPTION
The computerized engine control system, used on 2.5L models
with throttle body fuel injection, is built around an electronic
control unit (ECU). The ECU is a microprocessor-based computer.
The major function of the system is to reduce emissions. It
accomplishes this through a series of 13 sensors or switches that
constantly monitor several engine conditions. See Fig. 16.
Fig. 1: Vacuum Diagram for Jeep 2.5L CEC System
The computer processes input information from the sensors to
get an accurate picture of engine operation. It then provides output
control signals to regulate air/fuel ratio, ignition, idle speed and

emission control devices. This permits optimum engine performance
with minimum emissions.
OPERATION
The engine control system is divided into 6 sub-systems:
electronic control unit (also called the ECU or computer), sensors and\
switches, fuel control, emission control, idle speed control, and
ignition advance control.
ELECTRONIC CONTROL UNIT (ECU)
The ECU is located under the instrument panel, above the
accelerator pedal. It receives information from the 13 engine sensors
or switches to determine engine operating conditions at any particular
moment. The ECU responds to these signals by sending a control signal
to the fuel injector, fuel pump, ignition control module, idle speed
actuator (ISA) motor, EGR solenoid, and canister purge solenoid. It
also controls the Load Swap relay, and on Man. Trans. models, the up-
shift indicator lamp.
SENSORS & SWITCHES
Exhaust Gas Oxygen (EGO) Sensor
The amount of oxygen in exhaust gases varies according to the
air/fuel ratio of the intake charge. The exhaust gas oxygen sensor,
located in the exhaust pipe, detects this content and transmits a low
voltage signal to the ECU.
The outer surface of the sensor is exposed to exhaust gases,
the inner surface to outside air. The difference in the amount of
oxygen contacting the inner and outer surfaces of the sensor creates a
pressure, which results in a small voltage signal. This signal, which
is a measure of the unburned oxygen in the exhaust gas, is transmitted
to the ECU.
If the amount of oxygen in the exhaust system is low (rich
mixture), the sensor voltage signal will be high. If the mixture is
lean, the oxygen sensor will generate a low voltage signal.
The sensor has a heating element that keeps the sensor at
proper operating temperature during all operating modes.
Manifold Air/Fuel Temperature (MAT) Sensor
The manifold air/fuel temperature sensor is installed in the
intake manifold. This sensor provides a voltage signal to the ECU
representing the temperature of the air/fuel mixture in the intake
manifold. The ECU compensates for air density changes during high
temperature operation.
Coolant Temperature Sensor (CTS)
The coolant temperature sensor is located in the intake
manifold coolant jacket. This sensor provides a voltage signal to the
ECU. The ECU uses this signal to determine engine temperature. During
cold engine operation, the ECU responds by enriching the air/fuel
mixture delivered to the injector, compensating for fuel condensation
in the intake manifold, controlling engine warm-up speed, increasing
ignition advance, and inhibiting operation of the EGR system.
Manifold Absolute Pressure (MAP) Sensor
The MAP sensor detects absolute pressure in the intake
manifold as well as ambient atmospheric pressure. This information is
supplied to the ECU, through voltage signals, as an indication of
engine load. The sensor is attached to the plenum chamber near the
hood latch. A vacuum line from the throttle body supplies the sensor

with manifold pressure information.
Knock Sensor
The knock (detonation) sensor, located in the cylinder head,
provides an input signal to the ECU whenever detonation occurs. The
ECU then retards ignition advance to eliminate the detonation at the
applicable cylinders.
Speed Sensor
The speed sensor (or crankshaft position sensor) is mounted
at the flywheel/drive plate housing. The sensor detects the flywheel/
drive plate teeth as they pass during engine operation and sends an
electrical signal to the ECU, which calculates engine speed.
The flywheel/drive plate has a large trigger tooth and notch
located 90
and 12 small teeth before each top dead center (TDC)
position. When a small tooth or notch pass the magnetic core in the
sensor, the build-up and collapse of the magnetic field induces a
small voltage signal in the sensor pick-up windings.
The ECU counts these signals representing the number of teeth
as they pass the sensor. When a larger trigger tooth and notch pass
the magnetic core, a higher voltage signal is sent to the ECU. This
indicates to the ECU that a piston will be at the TDC position 12
teeth later. The ECU either advances or retards ignition timing as
necessary according to sensor inputs.
Battery Voltage
Battery voltage input to the ECU ensures that proper voltage
is applied to the injector. The ECU varies voltage to compensate for
battery voltage fluctuations.
Starter Motor Relay
The engine starter motor relay provides an input to the ECU,
indicating the starter motor is engaged.
Wide Open Throttle (WOT) Switch
The WOT switch is mounted on the side of the throttle body.
The switch provides a voltage signal to the ECU under wide open
throttle conditions. The ECU responds to this signal by enriching the
air/fuel mixture delivered to the injector.
Closed Throttle (Idle) Switch
This switch is integral with the idle speed actuator (ISA)
motor. The switch provides a voltage signal to the ECU, which
increases or decreases the throttle stop angle in response to engine
operating conditions.
Transmission Gear Position Indicator
The gear position indicator is mounted on vehicles equipped
with automatic transaxles. It provides a signal to the ECU to
indicate that the transaxle is in a driving mode and not in Park or
Neutral.
Power Steering Pressure Switch
The switch increases the idle speed during periods of high
power steering pump load and low engine RPM.
A/C Switch
The A/C switch sends a signal to the ECU when the air
conditioner is operating and when the compressor clutch must be
engaged to lower the temperature. The ECU, in turn, increases engine
speed to compensate for the added load of the air conditioner.
FUEL CONTROL

The ECU controls the A/C compressor clutch by means of the
A/C clutch relay. See Fig. 15.
UP-SHIFT INDICATOR LAMP
Manual transaxle vehicles are equipped with an up-shift
indicator lamp. The lamp is normally turned on when the ignition
switch is turned "ON", and is turned off when the engine starts.
The lamp will again light during engine operation, according
to engine speed and load conditions. A switch, located on the
transaxle, prevents lamp from lighting when transmission is shifted
to the next highest gear. If the shift of gears is not performed, the
ECU will turn the lamp off after 3-5 seconds.
MODES OF OPERATION
IGNITION SWITCH "ON" MODE
When the TBI system is activated by the ignition switch, the
system power relay is energized, and the fuel pump is energized by
the ECU through the fuel pump relay. The pump will operate for
approximately 1 second, unless the engine is operating or the starter
motor is engaged.
The ECU receives input from the CTS, MAT, and MAP sensors.
The up-shift indicator lamp is illuminated.
ENGINE START-UP MODE
When the starter motor is engaged, the ECU receives inputs
from the CTS and speed sensors, the starter motor relay, and the wide
open throttle switch. The fuel pump is activated by the ECU and
voltage is applied to the injector, with the ECU controlling
injection time.
The ECU determines proper ignition timing from the speed
sensor input. If the wide open throttle switch is engaged, the ECU
will deactivate the injector to prevent flooding.
ENGINE WARM-UP MODE
The ECU receives inputs from the CTS, MAT, MAP, speed, and
knock sensors. It also is informed of throttle, gear (automatic
transaxle models) and A/C control position.
The ECU provides a ground for the injector, precisely
controlling fuel delivery to the engine. The ECU also controls
ignition timing, engine idle speed and throttle stop angle. On
vehicles with manual transmissions, the up-shift indicator lamp is
controlled according to engine speed and load.
CRUISE MODE
During cruising speed, the ECU receives inputs from the CTS,
MAT, MAP, EGO, speed and knock sensors. It is also informed of
throttle, gear (automatic transaxle models), and A/C control position.\
The ECU provides a ground to the injector, precisely
controlling injector time. It also controls idle speed, throttle stop
angle, ignition timing, air/fuel mixture ratio and up-shift indicator
lamp.
DECELERATION MODE
During deceleration, the ECU receives inputs from the CTS,

NOTE: Voltage should drop 0.5-1.5 volts with hot engine, at idle.
Fig. 6: MAP Sensor Terminal Identification
If markings on MAP sensor vary from illustration, use markings on
sensor.
2) Test voltage at pin 33 of ECU connector for 4.0-5.0 volts
to verify wiring harness condition. Repair if required.
3) With ignition on, check for MAP sensor supply voltage of
4.5-5.5 volts at sensor connector pin C. Similar voltage should be
present at pin 16 of ECU connector. Repair or replace wiring harness
if required. Test for sensor ground between pin 17 of ECU connector
and pin A of sensor connector.
4) Using an ohmmeter, check for ground from pin 17 of ECU
connector to pin 2. If an open circuit is indicated, check for a
defective sensor ground on the flywheel housing near the starter
motor.
5) If ground is good, the ECU must be replaced. Before
replacing ECU, check to see if pin 17 of ECU connector is shorted to
12 volts. If so, correct the condition and test ECU before replacing.
Refer to the ELECTRONIC CONTROL UNIT TEST.
ELECTRONIC CONTROL UNIT

1) If all components have been checked and/or repaired, but
a system failure or problem still exists, the ECU may be at fault.
However, the ECU is a very reliable unit and must always be the final
component replaced if a doubt exists concerning the cause of a system
failure.
2) The only way to confirm an ECU malfunction is to take the
unit to an AMC dealer to have it tested. This is the only sure way to
avoid replacing a good ECU.
SYSTEM DIAGNOSIS
PRELIMINARY CHECKS
Be sure fuel is actually reaching the injector. Make sure no
air is entering the intake or exhaust system above the catalytic
converter. Before assuming an engine control system malfunction,
inspect the following systems to ensure components are in good
condition and are operating properly.
* All support systems and wiring.
* Battery connections and specific gravity.
* Electrical and vacuum connections on components and sensors.
* Emission control devices.
* Ignition system.
* Vacuum hoses.
CAUTION: Never connect or disconnect a component without turning the
ignition switch off. Never apply more than 12 volts or AC
voltage to system terminals. Disconnect battery cables
before charging it. Remove ECU if temperatures are expected
to exceed 176
F (80C), such as in a paint shop bake oven.
DIAGNOSTIC TEST CHARTS
Following are 6 different diagnostic test flow charts,
providing the shortest means of testing the system. These include:
* Ignition Switch "OFF" Chart - Tests system power for ECU
memory keep-alive voltage.
* Ignition Switch "ON" Power Chart - Tests system power
function and fuel pump power function.
* Ignition Switch "ON" Input Chart - Tests closed throttle
(idle) switch, wide open throttle (WOT) switch, manifold
absolute pressure (MAP) sensor, park/neutral switch, coolant
temperature sensor (CTS), manifold air/fuel temperature (MAT\
)
sensor and the respective switch or sensor circuits.
* System Operational Chart - Tests engine start-up and fuel
injector circuits, plus function of closed loop air/fuel
mixture, coolant temperature sensor, manifold air/fuel
temperature sensor, knock sensor and closed loop ignition
retard/advance, EGR valve and canister purge solenoid, idle
speed actuator, and A/C control.
* Basic Engine Chart - Indicates possible failures within other
engine related components.
* Man. Trans. Up-shift Chart - Tests up-shift indicator lamp
function on manual transmission vehicles.

assembly. To install, reverse removal procedure.
ADJUSTMENTS
NOTE: The following adjustment procedures should not be necessary
during normal vehicle operation or maintenance. Adjustment
of the listed components should only be required when a
faulty component is replaced with a new one.
IDLE SPEED ACTUATOR (ISA) MOTOR
1) With air cleaner removed, air conditioner off (if
equipped) and engine at normal operating temperature, connect a
tachometer to terminals 1 (+) and 3 (-) of the small diagnostic
connector D1. See Fig. 16. Turn ignition off and observe ISA motor
plunger. The plunger should move to fully extended position.
2) With ISA plunger fully extended, disconnect wire
connector and start engine. Engine speed should be 3300-3700 RPM. If
not, turn hex head screw on end of plunger until correct speed is
obtained.
3) Hold closed throttle switch plunger all the way in while
opening throttle. Release the throttle. Throttle lever should not make
contact with the plunger. If contact is made, inspect throttle
linkage and/or cable for binding or damage. Repair as needed.
4) Reconnect ISA motor wire connector and turn ignition off
for 10 seconds. Motor should move to fully extended position. Start
engine. Engine speed should be 3300-3700 RPM for a short time and
then fall to normal idle. Turn off engine and remove tachometer.
5) When final adjustments have been made, apply thread
sealer to adjustment screw threads to prevent movement. Install air
cleaner.
WIDE OPEN THROTTLE SWITCH
1) Remove the throttle body assembly from the engine, and
loosen 2 WOT switch retaining screws. Hold throttle in wide open
position, and attach a Throttle Angle Gauge (J-26701) to flat surface
of the throttle lever.
2) Rotate scale to align the 15
mark with the pointer.
Level the gauge. Rotate scale to align zero with the pointer, and
close the throttle enough to center bubble. This positions the
throttle at 15
before wide open throttle.
3) Adjust the WOT switch lever on the throttle cam so that
the plunger is just closed at 15
position. Tighten the retaining
screws, and remove the gauge.

\003
4.0 L C EC S YSTE M

1988 J e ep C hero ke e
1988 COMPUTERIZED ENGINE Controls
ENGINE CONTROL SYSTEM
JEEP 4.0L MPFI 6-CYLINDER
Cherokee, Comanche & Wagoneer
DESCRIPTION
The 4.0L engine control system controls engine operation to
lower exhaust emissions while maintaining good fuel economy and
driveability. The system is designed to maintain a 14.7:1 air/fuel
ratio under all engine operating conditions. When the ideal air/fuel
ratio is maintained, the catalytic converter can control oxides of
nitrogen (NOx), hydrocarbon (HC), and carbon monoxide (CO) emissio\
ns.
The system consists of the following sub-systems: Fuel
Control, Data Sensors and Switches, Electronic Control Unit (ECU),
Diagnostics, Electronic Spark Advance, Idle Speed Control, Exhaust Gas
Recirculation, and Transmission Shift Light.
OPERATION
FUEL CONTROL
The fuel control system delivers fuel to the engine. Fuel
from the in-tank fuel pump flows to the fuel rail, injectors and
pressure regulator. The pressure regulator maintains fuel system
pressure at 31-39 psi (2.l-2.7 kg/cm
). Excess fuel is returned to the
tank by a fuel return line.
The fuel pump is energized through the fuel pump relay that
is located on the right inner fender panel in the engine compartment.
Battery voltage is provided through the ignition switch and is
energized when the ECU completes the ground path.
The fuel injectors are electrically operated solenoid valves.
The ECU determines injector pulse width ("on/off") time based upon
engine operating conditions and delivers the proper pulse width to
maintain an air/fuel ratio of 14.7:l.
The ECU varies the amount of voltage applied to the injectors
to compensate for battery voltage changes. Battery voltage information
is provided to the ECU through the wiring harness. No sensor or switch
is required.
DATA SENSORS & SWITCHES
Each sensor and/or switch furnishes electronic impulses to
the ECM. Based on these input signals, the ECM computes spark timing
and air/fuel mixture for proper engine operation.
Coolant Temperature Sensor (CTS)
The CTS is located on the left side of the block, just below
exhaust manifold. The sensor provides coolant temperature information
to the ECU. Engine coolant temperature is used by the ECU for the
following functions:
* Enrich air/fuel mixture for cold engine starts.
* Control idle speed during warm-up.
* Increase spark advance during cold engine operation.
* Prevent EGR flow during cold engine operation.

proper increased enrichment for the next engine start. Idle speed is
nonadjustable.
EMISSION CONTROL
The ECU electrically controls Exhaust Gas Recirculation (EGR).\
An ECU-controlled solenoid valve is used to control EGR valve
function. This valve is located on the left inner fender panel and is
operated by the ECU in response to coolant temperature, throttle
position, and manifold pressure.
Under conditions of engine warm-up, engine idle, wide open
throttle, or rapid acceleration/deceleration, the solenoid valve is
energized, blocking vacuum to the EGR valve. At normal operating
temperatures with engine speed above idle, the solenoid valve is de-
energized, allowing normal EGR valve function.
NOTE: If the electrical connector is removed from the EGR solenoid,
EGR flow will be allowed at all times.
A/C CLUTCH CONTROL
The ECU controls the A/C compressor clutch to improve idle
quality. The A/C compressor clutch will be engaged or disengaged as
deemed necessary by the ECU through the A/C clutch relay.
SHIFT LIGHT CONTROL
The shift light system is used on all manual transmission
equipped vehicles. The ECU monitors coolant temperature, throttle
position, vehicle speed, and engine speed to control the shift light.
The ECU calculates what gear position the vehicle should be in and
uses this information to turn on the light. The light indicates the
best shift point to the driver for maximum fuel economy.
The light is tested when the ignition switch is turned on.
When the engine is started, the light should go out. A transmission-
mounted switch prevents the light from illuminating when the
transmission is shifted into high gear. The ECU turns the light off if
the shift to the next higher gear is not performed within 3-5 seconds
after light comes on.
DIAGNOSIS & TESTING
PRELIMINARY CHECKS
Before assuming that the ECU is faulty, the following systems
and components must be in good condition and operating properly:
* Air filter.
* All support systems and wiring.
* Battery connections and specific gravity.
* Compression pressure.
* Electrical and vacuum connections to components, sensors and
switches.
* Emission control devices.
* Ignition system.
* All vacuum and fuel line (hose) connections.
FUEL SYSTEM TEST
Fuel Pressure
1) Remove cap from pressure test port on fuel rail and

AB BREVIA TIO NS

1988 J e ep C hero ke e
GENERAL INFORMATION
COMMONLY USED ABBREVIATION
"A" ABBREVIATION TABLE
"A" ABBREVIATION TABLE







\









\








\









\









\









\









\






 
ABBREVIATION DEFINITION 










\








\b
\









\









\









\









\









\






A Amperes 

A/C Air Conditioning 

A/T Automatic Transmission/Transaxle 

AAP Auxiliary Accelerator Pump 

AB Air Bleed 

ABCV Air Bleed Control Valve 

ABDC After Bottom Dead Center 

ABRS Air Bag Restraint System 

ABS Anti-Lock Brake System 

AC Alternating Current 

ACC A/C Clutch Compressor 

ACCS A/C Cycling Switch 

ACCUM Accumulator 

ACCY Accessory 

ACT Air Charge Temperature Sensor 

ACV Thermactor Air Control Valve 

ADJ Adjust or Adjustable 

ADV Advance 

AFS Airflow Sensor 

AI Air Injection 

AIR or A.I.R. Air Injection Reactor 

AIS Air Injection System 

ALCL Assembly Line Communications Link 

ALDL Assembly Line Diagnostic Link 

ARC Automatic Ride Control 

ASCD Automatic Speed Control Device 

ASCS Air Suction Control Solenoid 

ASD Auto Shutdown 

ASDM Air Bag System Diagnostic Module 

ASV Air Suction Valve 

ATC Automatic Temperature Control 

ATDC After Top Dead Center 

ATF Automatic Transmission Fluid 

ATS Air Temperature Sensor 

AXOD Automatic Transaxle Overdrive 

Abs. Absolute 

Accy. Accessory 

Alt. Alternator or Altitude 

Amp. Ampere 

Assy. Assembly 

Auto. Automatic 

Aux. Auxiliary 

Avg. Average 











\








\









\









\









\









\









\





\f

"B" ABBREVIATION TABLE
"B" ABBREVIATION TABLE