service schedule JEEP CHEROKEE 1988 Service Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 1988, Model line: CHEROKEE, Model: JEEP CHEROKEE 1988Pages: 1378, PDF Size: 19.9 MB
Page 589 of 1378
All involved vehicles will be entered to DIAL System Function 70 at
the time of recall implementation for dealer inquiry by VIN as needed.
PARTS
IMPORTANT: A quantity of parts will be distributed initially and
billed to all involved dealers. This quantity will cover
a portion of the total vehicles involved. Additional parts
may be ordered as needed to support customer demand.
Each involved dealer, to whom vehicles in the recall were invoiced
(or the current dealer at the same street address), will receive
enough Emission Service Packages, Recall PN C3906170, to service 25%
of those vehicles.
Each parts package contains the following components:
EMISSION SERVICE PACKAGE
\
\
\
\
\
\
\
Qty Description Qty Description
\b\
\
\
\b\
\b\
\
1 Oxygen Sensor 1 Clamp
1 Catalytic Converter 4 Bolts
1 Gasket 4 Nuts
1 Recall Completion Label 1 Instruction Sheet
\
\
\
\
\
\
\
\f
OWNER NOTIFICATION & SERVICE SCHEDULING
All involved vehicle owners known to Chrysler are being notified of
the service requirement by first class mail. They are requested to
schedule appointments for the service with their dealers at the
earliest possible date. A copy of the
CUSTOMER NOTIFICATION LETTER is
in this bulletin.
Enclosed with each owner notification is an Owner Notification Form.
The involved vehicle and recall are identified on the form for owner
or dealer reference as needed.
SERVICE PROCEDURE
A. Replace Oxygen Sensor
1. Locate the oxygen sensor in the exhaust manifold as shown in
Fig. 1 .
2. Disconnect the oxygen sensor electrical connector.
3. Remove the oxygen sensor.
4. Clean the exhaust manifold threads using a thread chaser.
NOTE: Do not use solvents or lubricants on threads.
5. Install provided oxygen sensor. Tighten to 22 ft-lbs (30 N-m)
6. Connect oxygen sensor electrical connector.
Page 593 of 1378
Chrysler Corporation has determined that some 1989 and 1990 Jeep
Cherokee, Comanche and Wrangler vehicles equipped with a 2.5L engine,
may be in violation of Federal Emissions Standards.
The Problem is... The oxygen sensor and catalytic convener on your
vehicle (identified on the enclosed form), may be
susceptible to failure. This could result in
hydrocarbon (HC), carbon monoxide (CO) and oxides
of nitrogen (NOx) emission levels above the
allowable limits, which were established to protect
the public health from the dangers of air pollution.
What you must do... * Simply contact your Jeep dealer to schedule
a service appointment. Ask the dealer to hold
parts for your vehicle or order them prior to
your appointment.
* Bring the enclosed Owner Notification Form with
you to your dealer. It tells the dealer what
service is required for your vehicle.
What Chrysler and Chrysler will repair your vehicle free of charge
your dealer will do... (parts and labor). To do this, your dealer will
replace the oxygen sensor and catalytic
converter. The service will take about one hour
but additional time may be required depending on
how service work is scheduled and processed.
If you need help... If you have trouble getting your vehicle
repaired, please call the Chrysler Customer
Center, toll free, at 1-800-853-1403.
A representative will assist you in getting your
vehicle repaired. If you are still unable to
obtain the repair as described in this letter
within a reasonable time, you may also contact
the Manufacturers Operations Division of the
Environmental Protection Agency (6405J), 401 M
Street, S.W., Washington, D.C. 20460.
In order to ensure your full protection under the emission warranty
made applicable to your vehicle under Federal law, and your right to
participate in future recalls, it is recommended that you have your
vehicle serviced as soon as possible. Failure to do so could legally
be determined to be a lack of proper maintenance of your vehicle.
Further, without this repair your vehicle may fail a state or local
emission inspection test.
We're sorry for any inconvenience, but trust that you understand our
interest in clean air and your continuing satisfaction with our
product. Thanks for your attention to this important matter.
Customer Services Field Operations
Chrysler Corporation
Page 902 of 1378
MAIN TE N AN CE IN FO RM ATIO N
1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance Information
Jeep; Cherokee,
Wagoneer
* PLEASE READ THIS FIRST *
NOTE: For scheduled maintenance intervals and the related fluid
capacities, fluid specifications and labor times for major
service intervals, see SCHEDULED SERVICES article below:
* SCHEDULED SERVICES - GASOLINE
* SCHEDULED SERVICES - DIESEL ENGINES - NORMAL (1985-87)
Warranty information and specifications for fluid
capacities, lubrication specifications, wheel and tire size,
and battery type are covered in this article.
MODEL IDENTIFICATION
VIN LOCATION
The Vehicle Identification Number (VIN) is located on the
left side of the dash panel at the base of the windshield. The VIN
chart explains the code characters.
VIN CODE ID EXPLANATION
Numbers preceding the explanations in the legend below refer
to the sequence of characters as listed on VIN identification label.
See VIN example below.
\
\
\
\
\
\
(VIN) 1 J C U N 7 7 1 X G T 0 0 0 0 0 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
\
\
\
\
\
\
1 - Manufacturing Country
1
* United States
2 - Company/Make
J * American Motors/Jeep
3 - Type
C * Multi-Purpose Vehicle
D * Incomplete Vehicle
E * Export, LHD
F * Export, RHD
4 - Engine Type
B * 2.1L (128 CID) 4-Cylinder Turbo (Diesel) (001B) (1985-87)
H * 2.5L (150 CID) 4-Cylinder TBI (Gasoline) (001H) (1986-88)
U * 2.5L (150 CID) 4-Cylinder 1-Bbl. (Gasoline) (001U) (1984-85)
Y * 2.5L (150 CID) 4-Cylinder 1-Bbl. (Export) (001Y) (1984-85)
W * 2.8L (171 CID) V6 2-Bbl. (Gasoline) (001W) (1984-86)
M * 4.0L (242 CID) I-6 (Gasoline) (001M) (1987-88)
Page 903 of 1378
5 - Transmission/(Transfer Case)
A * Auto Column Shift (2WD)
B * Auto Floor Shift (Part Time 4WD)
C * Auto Floor Shift (Full Time 4WD)
D * Auto Floor Shift (2WD)
E * Auto Column Shift (Part Time 4WD)
J * Auto Column Shift (Full Time 4WD)
L * 5-Speed Manual Floor Shift (Part Time 4WD)
N * 5-Speed Manual Floor Shift (Full Time 4WD)
S * 4-Speed Manual Floor Shift (2WD)
W * 5-Speed Manual Shift (2WD)
X * 4-Speed Manual Floor Shift (Part Time 4WD)
6-7 - Body Style
73 * Cherokee Wagon 2-Door (2WD)
74 * Cherokee Wagon 4-Door (2WD)
75 * Wagoneer Wagon 4-Door (4WD)
77 * Cherokee Wagon 2-Door (4WD)
78 * Cherokee Wagon 4-Door (4WD)
8 - Trim Package
1 * Custom
2 * Pioneer
3 * Chief
4 * Laredo
5 * Base
5 * Wagoneer
6 * Limited
K * Cherokee Base (2WD)
L * Pioneer (2WD)
M * Laredo (2WD)
9 - Check Digit
* Manufacturer Assigned
10 - Model Year
E * 1984
F * 1985
G * 1986
H * 1987
J * 1988
11 - Assembly Plant
T * Toledo, Ohio
12-17 - Sequential Serial Number
* Production Sequence
MAINTENANCE SERVICE INFORMATION
SEVERE & NORMAL SERVICE DEFINITION
NOTE: Use the Severe Service schedule if the vehicle to be serviced
is operated under ANY (one or more) of these conditions:
Service is recommended at specified mileage intervals of
vehicle operation. Service schedules are based on the following
primary operating conditions:
Severe Service
* Short Trips (About 15 Miles)
Page 904 of 1378
* Cold Climate Operation
* Towing Or Heavily Loading
* Severe Dust Conditions
* Sustained High Speed Operation
* Off-Road Driving
* Hot Weather, Stop-And-Go Driving
* Extensive Idling Conditions (Taxi Or Delivery Type Service)
Normal Service
* Driven More Than 10 Miles Daily
* No Severe Service Operating Conditions
CAMSHAFT TIMING BELT REPLACEMENT INFORMATION (TURBO-DIESEL)
CAUTION: Failure to replace a faulty camshaft timing belt may result
in serious engine damage.
The condition of camshaft drive belts should always be
checked on vehicles which have more than 50,000 miles. Although some
manufacturers do not recommend belt replacement at a specified
mileage, others require it at 60,000-100,000 miles. A camshaft drive
belt failure may cause extensive damage to internal engine components
on most engines, although some designs do not allow piston-to-valve
contact. These designs are often called "Free Wheeling".
Many manufacturers changed their maintenance and warranty
schedules in the mid-1980's to reflect timing belt inspection and/or
replacement at 50,000-60,000 miles. Most service interval schedules
reflect these changes.
Belts or components should be inspected and replaced if any
of the following conditions exist:
* Cracks Or Tears In Belt Surface
* Missing, Damaged, Cracked Or Rounded Teeth
* Oil Contamination
* Damaged Or Faulty Tensioners
* Incorrect Tension Adjustment
SERVICE LABOR TIMES
SERVICE LABOR TIMES TABLE (HOURS)\
\
\
\
\
\
\
( 1) 30,000 60,000
Application Mile Service Mile Service
2.1L (Turbo Diesel)
Automatic Transmission ........... 4.3 ................ 4.5
Manual Transmission .............. 3.6 ................ 3.8
2.5L
Automatic Transmission ........... 5.6 ................ 3.5
Manual Transmission .............. 4.9 ................ 3.5
2.8L
Automatic Transmission ........... 5.8 ................ 3.7
Manual Transmission .............. 5.1 ................ 3.7
4.0L
Automatic Transmission ........... 5.7 ................ 3.6
Manual Transmission .............. 5.0 ................ 3.6
( 1) - Add .8 hr. for vehicles equipped with 4WD.
\
\
\
\
\
\
\
Page 917 of 1378
WARNING: DO NOT USE starting fluids (ether) or flammable liquids to
aid the starting of a Cummins Turbo-Diesel. NEVER pour diesel
fuel, flammable liquids or starting fluids into the air
cleaner canister, air intake or turbocharger housing in an
attempt to start the vehicle. A flash fire may result causing
personal injury.
TRANSFER CASE
CAUTION: Both drive axles are disengaged when transmission gear is
in Neutral position. Always set parking brake when leaving
vehicle unattended.
CAUTION: Never attempt to engage Low range when vehicle is moving
faster than 2-3 MPH (3-5 KM/H). Transfer case damage may
result.
GASOLINES CONTAINING ALCOHOL
CAUTION: Exclusive use of gasohol is not recommended. Vehicle test
results have shown that significant fuel system corrosion
can result when gasohol is used exclusively. Fuel additives
which are now being sold as octane enhancers are not
recommended. Most of these products contain high
concentrations of methanol.
WARRANTY INFORMATION
CAUTION: Due to the different warranties offered in various regions
and the variety of after-market extended warranties
available, please refer to the warranty package that came
with the vehicle to verify all warranty options.
BASIC NEW CAR WARRANTY
Jeep Corporation warrants to the original purchaser that the
vehicle is free from defects under normal use and service for 12
months or 12,000 miles, whichever comes first.
POWERTRAIN PROTECTION LIMITED WARRANTY
Begins at 12 months or 12,000 miles and lasts for 7 years or
70,000 miles, whichever comes first. Warranty covers Engine,
Transmission, Transfer Case, and Drive Shaft/Drive Axle(s) for RWD &
4WD.
Items not covered include, normal scheduled maintenance,
tune-ups, clutch adjustments, lack of proper maintenance, and vehicles
on which the mileage cannot readily be determined. A 100.00 deductible
on 2WD models and a 150.00 deductible on 4WD models applies to each
repair visit.
Powertrain Warranty also covers cost of towing to nearest
Jeep Dealer if vehicle cannot be driven due to failure of a covered
powertrain part.
ANTI-CORROSION PERFORATION WARRANTY
Warrants the sheet metal parts of the vehicle against
perforation (rust-through) due to corrosion. It covers any body sheet
metal panel for unlimited mileage during the first 36 months. Outer-
body sheet metal panels are covered for 7 years or 100,000 miles,
Page 945 of 1378
IMPORTANT: A quantity of parts will be distributed initially and
billed to all involved dealers. This quantity will cover a
portion of the total vehicles involved. Additional parts
will ba supplied as indicated in the Special Parts Supply
Message with this notification letter.
Each involved dealer, to whom vehicles in the recall were invoiced
(or the current dealer at the same street address), will receive
enough Oxygen Sensor Packages, Recall P/N C3905610, to service 25% of
those vehicles (minimum of 5 and maximum of 20 packages).
Each uninvolved dealer will receive 5 parts packages to service
vehicles upon request.
Each parts package contains the following components:
PARTS INFORMATION
PARTS INFORMATION TABLE \
\
\
Description Qty.
\
\
\b
Oxygen Sensor 1
\
\
\b
Instruction Sheet 1
\
\
\f
OWNER NOTIFICATION & SERVICE SCHEDULING
All involved vehicle owners known to Chrysler are being notified of
the service requirement by first class mail. They are requested to
schedule appointments for the service with their dealers at the
earliest possible date. A copy of the
CUSTOMER NOTIFICATION LETTER is
in this bulletin.
Enclosed with each owner notification is an Owner Notification Form.
The involved vehicle and recall are identified on the form for owner
or dealer reference as needed.
SERVICE PROCEDURE
A. OXYGEN SENSOR INSPECTION
1. Raise Vehicle on a hoist and locate oxygen sensor in exhaust
manifold as shown in Fig. 1.
a. If the oxygen sensor has a metal stone shield around the sensor
body continue with Step B.
b. If the sensor does not have a stone shield, a new sensor has
already been installed and no further service is required.
WARNING: Exhaust manifold becomes very hot during engine operation.
Allow engine to cool before removing oxygen sensor.
1. Disconnect the oxygen sensor electrical connector.
2. Remove oxygen sensor using a crowfoot socket.
3. Clean exhaust manifold threads.
Page 947 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual \
\
\
\
\
\
\
EMISSIONS RECALL - OXYGEN SENSOR](/img/16/57037/w960_57037-946.png "JEEP CHEROKEE 1988 Service Repair Manual \
\
\
\
\
\
\
EMISSIONS RECALL - OXYGEN SENSOR")
\
\
\
\
\
\
\
EMISSIONS RECALL - OXYGEN SENSOR REPLACEMENT
Dear Chrysler Vehicle Owner:
Chrysler Corporation and the Environmental Protection Agency has
determined that the oxygen sensor on certain Cherokee, Wagoneer and
Comanche models may be susceptible to failure. Failure of the oxygen
sensor may cause your vehicle to be in violation of Federal Emissions
Standards. For this reason, we are asking you to return your vehicle,
identified by the Vehicle Identification Number on the enclosed form,
to your dealer for a special service repair. This service will be
provided free of charge.
The needed instructions have been sent to all involved dealers. The
service will not hurt your engine performance or fuel economy. To
obtain this service:
* Contact your Jeep/Eagle dealer as soon as possible to make an
appointment for the free service.
* Take the enclosed Owner Notification Form with you at the time of
your appointment and give it to your dealer. The form identifies
the vehicle and recall for which service is required.
* The dealer will inspect and replace the oxygen sensor if
necessary. The service will take about one-half hour, but
additional time may be required depending on how service
appointments are scheduled and processed.
In order to ensure your full protection under the emission warranty
made applicable to your vehicle under Federal law, and your right to
participate in future recalls, it is recommended that you have your
vehicle serviced as soon as possible. Failure to do so could legally
be determined to be a lack of proper maintenance of your vehicle.
Further, without this repair your vehicle may fail a state or local
emission inspection test.
If you have any problem obtaining the service, please contact the
Chrysler Zone Service Office in your area. (It is listed under
"Service Assistance" in your Owner's Manual.} A Zone representative
will arrange for prompt servicing of your vehicle. If you are still
unable to obtain the repair as described in this letter within a
reasonable time, you may also contact the Manufacturers Operations
Division of the Environmental Protection Agency (6405d), 401 M Street
S. W., Washington, D. C. 20460.
We regret any inconvenience this action may cause, but trust you
understand our interest in clean air and in your continuing
satisfaction with our product. Thank you for your prompt attention to
this important matter.
Customer Services Field Operations
Chrysler Corporation
\
\
\
\
\
\
\
COMPLETION REPORTING & REIMBURSEMENT
Claims for vehicles which have been serviced must be submitted on
the DIAL System. Claims submitted will be used by Chrysler to record
recall service completions and provide dealer payments.
Page 950 of 1378
\003
SC HED ULE D S ER VIC ES - G ASO LIN E
1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance & Service Intervals - Gasoline
Jeep; Cherokee, Wagoneer
* PLEASE READ THIS FIRST *
NOTE: All SERVICE SCHEDULES are listed for normal service
vehicles. If vehicle is operated under severe service
conditions, see SEVERE SERVICE REQUIREMENTS (PERFORM
W/SERVICE SCHEDULES) for items requiring additional
maintenance.
NOTE: This article contains scheduled maintenance service
information. Fluid types and capacities listed with each
service in this article are only those necessary to perform
that scheduled service. For specifications pertaining to
fluid capacities for the entire vehicle, fuse and circuit
breaker identification, wheel and tire size, battery type,
warranty information, or model identification refer to the
MAINTENANCE INFORMATION article in this section.
CAUTIONS & WARNINGS
AIR CONDITIONING MAINTENANCE
WARNING: NEVER add A/C refrigerant to correct a non-cooling problem
unless pressure gauges are connected to the system by a
certified technician. Lack of cooling may be caused by a
restriction, therefore adding refrigerant can cause a
dangerous pressure rise.
ANTI-LOCK BRAKE SYSTEM (If Equipped)
The anti-lock brake system contains electronic equipment that
can be susceptible to interference caused by improperly installed or
high output radio transmitting equipment. Since this interference
could cause the possible loss of the anti-lock braking capability,
such equipment should be installed by qualified professionals.
On models equipped with anti-lock brake systems, ALWAYS
observe the following cautions:
* DO NOT attempt to bleed hydraulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES Section.
* DO NOT mix tire sizes. As long as tires remain close to the
original diameter, increasing the width is acceptable.
Rolling diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* Use ONLY recommended brake fluids. DO NOT use silicone brake
fluids in an ABS-equipped vehicle.
BATTERY WARNING
WARNING: When battery is disconnected, vehicles equipped with
Page 957 of 1378
Fig. 5: Identification Label Locations
Courtesy of American Motors Corp.
SPARK PLUG REPLACEMENT INTERVALS
Spark plug replacement intervals, if given, are for Original
Equipment Manufacturer (OEM) installed or specified plugs. If vehicle
is equipped with platinum type or other non-OEM type spark plugs,
follow replacement interval specified by spark plug manufacturer.
OXYGEN SENSOR
If vehicle is equipped with an oxygen sensor, replace at 82,
500 miles or when the emissions maintenance reminder light remains on
continuously with the key in the ON position, whichever occurs first.
SEVERE & NORMAL SERVICE DEFINITIONS
CAUTION: Use the Severe Service schedule if the vehicle to be serviced
is operated under ANY (one or more) of these conditions:
Service is recommended at mileage intervals based on vehicle
operation. Normal Service and Severe Service are based on the
following primary operating conditions:
Severe Service
* Short Trips (About 15 Miles)
* Desert Or Cold Climate Operation
* Towing Or Heavily Loaded
* Severe Dust Conditions
* Hot Weather, Stop-And-Go Driving