tow JEEP CHEROKEE 1988 Service Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 1988, Model line: CHEROKEE, Model: JEEP CHEROKEE 1988Pages: 1378, PDF Size: 19.9 MB
Page 5 of 1378
specification. Install front cover oil seal. See FRONT COVER OIL SEAL
Remove front cover seal installer.
4) Reverse removal procedures. Lubricate vibration damper
retaining bolt with oil prior to installation. Tighten bolts to
specification.
FRONT COVER OIL SEAL
Removal & Installation
1) Remove vibration damper. Using Seal Remover (J-9256),
remove seal from front cover. Position new seal on Front Cover Seal
Installer (J-22248) with lip facing outward.
2) Apply sealant to seal outer diameter. Lightly coat
crankshaft with oil. Place front cover seal installer on front of
crankshaft. Tap seal into front cover. Remove seal installer. Lightly
coat seal contact area of vibration damper with oil.
3) Install key in crankshaft (if removed). Install vibration\
damper. Lubricate vibration damper bolt with oil. Install retaining
bolt and washer. Tighten to specification.
CAMSHAFT & TIMING GEAR
Removal
1) Drain cooling system. Remove radiator. Remove engine front
cover. See ENGINE FRONT COVER. Remove distributor. Remove fuel pump
(if equipped with mechanical pump). Remove rocker arms and pushrods.
See ROCKER ARMS & BRIDGE under VALVES.
2) Remove valve lifters. Mark lifters for location. Remove
crankshaft oil slinger. Pull chain tensioner block toward tensioner
lever to compress spring. Hold block and move tensioner lever to lock
position. See Fig. 3.
3) Rotate crankshaft and align timing marks on crankshaft and
camshaft gears. Remove camshaft gear retaining bolt. Remove gears and
timing chain. Remove camshaft.
Fig. 3: Location of Chain Tensioner Lock
Courtesy of Chrysler Motors.
Inspection
Inspect camshaft for flaking, lobe wear or worn bearing
Page 7 of 1378
OIL PAN
See OIL PAN REMOVAL article.
PISTON & ROD ASSEMBLY
NOTE: Mark piston cylinder location for reassembly reference.
Install pistons in original cylinder location.
Removal
1) Remove cylinder head. See CYLINDER HEAD under MANIFOLDS &
CYLINDER HEAD. Remove oil pan. See OIL PAN REMOVAL article. Remove
ridge or deposits from cylinder bore.
2) Mark connecting rod and piston for cylinder ID. Remove
bearing cap. Remove piston and rod assembly.
CAUTION: Arrow on top of piston must point toward front of engine.
Oil squirt holes in connecting rod must face camshaft when
installed.
Installation
1) Ensure ring end gap and side clearance are within
specification. See ENGINE SPECIFICATIONS tables. Install rings on
piston. Position ring end gaps at specified areas. See Fig. 5.
Fig. 5: Positioning Piston Ring Gaps
Ring gaps may vary 20 degrees from positions illustrated.
2) Lubricate piston assembly and cylinder block. Install
piston assembly. Arrow on top of piston must face toward front of
Page 8 of 1378
engine and connecting rod oil squirt hole should face camshaft side of
engine.
3) Install bearings. Check oil clearance and connecting rod
side play clearance. Reverse removal procedures for remaining
components. Tighten bolts to specification.
Fitting Pistons
1) Determine cylinder taper, wear and out-of-roundness and
piston clearance. For cylinder specifications, see CYLINDER, PISTON &
CONNECTING ROD SPECIFICATIONS table. If taper or out-of-roundness are
not within specification, hone or bore cylinders for installation of
new pistons.
2) Measure piston at right angle of the piston pin at the
center line of the pin. Compare reading to cylinder bore to determine
clearance. Mark fitted piston for cylinder location.
CYLINDER, PISTON & CONNECTING ROD SPECIFICATIONS TABLE
\
\
\
\
\
\
Application In. (mm)
Connecting Rod
Crankshaft Bore .......... 2.2080-2.2085 (56.083-56.095)
Pin Bore ................... .9288-.9298 (23.591-23.616)
Cylinder Bore
Diameter ................. 3.8751-3.8775 (98.427-98.488)
Out-of-Round ................................ .001 (.02)
Taper ....................................... .001 (.02)
Piston Pin Bore Diameter ..... .9308-.9313 (23.642-23.655)
Piston Pin Diameter .......... .9304-.9309 (23.632-23.644)
Piston-to-Cylinder Clearance ..... .0009-.0017 (.022-.043)
\
\
\
\
\
\
PISTON PIN REPLACEMENT
NOTE: Note direction of arrow on piston and oil squirt hole in
connecting rod prior to removal.
Removal
Position piston on Support (J-21872-1), Pin Pilot (J-21872-2\
)
and Driver (J-21872-3) on an arbor press. See Fig. 6. Press piston pin
from piston.
NOTE: Piston and pin must be at standard room temperature when
measuring fit. Piston pin should gravity-fall through the
piston at room temperature. Piston pin cannot be reused
after removal.
Inspection
Measure piston pin diameter, piston bore and connecting rod
bores. Replace components if not within specification. See CYLINDER,
PISTON & CONNECTING ROD SPECIFICATIONS table.
NOTE: Connecting rod must be positioned on the piston so the oil
squirt hole faces the camshaft side of the engine with
piston installed with arrow toward the front of the engine.
Installation
1) Insert pin pilot through piston and connecting rod. Place
assembly on support. Insert piston pin through the upper piston pin
bore and into connecting rod pin bore. See Fig. 6.
Page 10 of 1378
NOTE: Crankshaft journal diameters are indicated by a color coded
mark placed on the adjacent counterweight or cheek toward
the flanged (rear) end of crankshaft. Note color code to
determine proper bearing usage. Check oil clearance after
bearing installation.
Removal
1) Remove oil pan. See OIL PAN REMOVAL at end of ENGINE
section. See oil pump. See OIL PUMP under ENGINE OILING. Remove main
bearing cap.
2) Rotate crankshaft to position rod to be serviced at bottom
of stroke. Mark bearing cap and connecting rod. Remove bearing cap
with bearing. Push piston and rod assembly up to remove upper bearing.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Using Plastigage method, check bearing clearances. Replace
bearings as necessary to obtain correct clearance. Bearings are
available in standard and undersize application.
2) If required, different sized upper and lower bearings may
be installed to obtain correct oil clearance. Tighten bolts to
specification. Check rod side play. Rotate crankshaft to ensure
freedom of movement. Reverse removal procedures for remaining
components. Tighten bolts to specification.
NOTE: Avoid combining bearing inserts in excess of .001" (.02 mm)
difference in size. Odd size inserts must be on bottom (rod
cap) side.
MAIN BEARINGS
Removal
1) Remove oil pan. See OIL PAN REMOVAL at end of ENGINE
section. Remove oil pump. See OIL PUMP under ENGINE OILING.
2) Ensure main bearing caps are marked for location. Rotate
crankshaft to remove bearings. Note color code on edge of bearing.
NOTE: Crankshaft journal diameters are indicated by a color coded
mark placed on the adjacent counterweight or cheek toward
the flanged (rear) end of crankshaft. Note color code to
determine proper bearing usage. Check oil clearance after
bearing installation.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Ensure caps are installed in original location. Using
Plastigage method, check bearing clearances.
2) Replace bearings as necessary to obtain correct clearance.
Bearings are available in standard and undersize applications. If
required, different sized upper and lower bearings may be installed to
obtain correct oil clearance.
NOTE: If different sized bearings are used, the odd sized bearings
must all be uniform in location (upper or lower). DO NOT use
bearings with a thickness difference exceeding .001" (.02
mm).
3) Apply Loctite to corners of rear main bearing cap prior to
final installation. Tighten bolts to specification. Check crankshaft
end play. See CRANKSHAFT END PLAY. Rotate crankshaft to ensure freedom
of movement. Reverse removal procedures for remaining components.
Tighten bolts to specification.
Page 11 of 1378
Crankshaft End Play
1) Using dial indicator, check crankshaft end play. Inspect
crankshaft thrust surfaces or thrust bearing for wear if not within
specification. See ENGINE SPECIFICATIONS table.
2) Replace thrust bearing if required. When replacing thrust
bearing, pry crankshaft forward then reward prior to tightening main
bearing cap to specification. Recheck end play. Replace crankshaft if
not within specification.
REAR MAIN BEARING OIL SEAL
Removal
Remove transmission, clutch housing and flywheel or drive
plate. Using screwdriver, pry oil seal from housing. Avoid damage to
surrounding area.
NOTE: Shim must be used when installing old type oil seal Part No.
(324 1669) only. DO NOT use shim when installing new type
oil seal Part. No. (8933 004 143).
Installation
1) Position wing nut on Seal Installer (J-36306) until it
contacts the shaft nut. See Fig. 7. Install shim if old type seal Part
No. (324 1669) is used.
2) Lubricate inner and outer edges of seal. Install seal on
seal installer with seal dust shield toward the wing nut. Install seal
installer on crankshaft so pilot and dowel are positioned on the
crankshaft.
3) Thread the seal installer attaching screws into the
crankshaft and tighten. Rotate wing nut until it bottoms. This will
properly position the seal.
4) Remove seal installer. Ensure dust shield is not curled
under. Reverse removal procedures for remaining components.
Fig. 7: Installing Rear Main Bearing Oil Seal
WATER PUMP
Removal
Page 23 of 1378
input sensors. During engine start-up, the injector delivers an extra
amount of fuel to aid in starting.
EMISSION CONTROL
Both EGR and canister purge operation are regulated by the
ECU. Regulation of these 2 systems is accomplished through the use of
an electrically-operated vacuum solenoid.
Whenever the solenoid is energized by the ECU, it prevents
vacuum action on the EGR valve and canister. The solenoid is
energized by the ECU during engine warm-up, improving cold
driveability. It is also energized during closed throttle (idle),
wide open throttle and during rapid acceleration or deceleration.
In this way the EGR is prevented from operating until the
engine reaches a predetermined temperature. The canister purge does
not operate until the oxygen sensor warms up and becomes operational.
This prevents an over-rich mixture until the oxygen sensor can
compensate for the extra fuel vapor.
IDLE SPEED ACTUATOR (ISA)
The ISA motor, located on the throttle body, is an
electrically-driven actuator that changes the throttle stop angle by
acting as a movable idle stop. The ECU commands the ISA to control
engine idle speed and maintain a smooth idle during sudden engine
deceleration. It does this by providing the appropriate voltage
outputs to produce the idle speed or throttle stop angle required for
the particular engine operating condition. There is no idle speed
adjustment.
For cold engine starting, the throttle is held open for a
longer period to provide adequate engine warm-up prior to normal
operation. When starting a hot engine, the throttle is open for
shorter time.
Under normal engine operating conditions, engine idle is
maintained at a pre-programmed RPM, which may vary slightly due to
engine operating conditions. Under certain engine deceleration
conditions, the throttle is held slightly open.
IGNITION ADVANCE CONTROL
Under certain engine operating conditions, the predetermined
ignition advance curve is modified. This is accomplished through 2
switching circuits that connect the ECU and the ignition control
module.
ECU-CONTROLLED RELAYS
System Power Relay
Located on the right strut tower, this relay is energized
during engine start up and remains energized until 3 to 5 seconds
after the engine is stopped. This permits the ECU to extend the idle
speed actuator for the next start up and then cease operation. See
Fig. 4.
Page 61 of 1378
Removal
1) Drain cooling system. Remove radiator. Discharge A/C
system if necessary. Remove A/C condenser and receiver assembly (if
equipped). Remove fuel pump (if equipped with mechanical pump),
ignition wires and distributor.
2) Remove cylinder head. See CYLINDER HEAD in this article.
Remove hydraulic lifters. Using Lifter Remover/Installer (J-21884),
remove lifters. Mark lifter location for reassembly reference.
3) Remove engine front cover. See ENGINE FRONT COVER in this
article. Remove timing chain and sprockets. Remove front bumper and
grille (if necessary). Carefully remove camshaft.
Inspection
Inspect camshaft for flaking, lobe wear or worn bearing
journals. Replace if not within specification. See ENGINE
SPECIFICATIONS tables.
Installation
Lubricate camshaft and install into place. Use care not to
damage camshaft bearings. Reverse removal procedure to complete
installation. Tighten bolts to specification.
Camshaft Bearing
Replace camshaft bearings using camshaft bearing
remover/installer. Ensure oil holes are aligned after installation.
OIL PAN
See OIL PAN REMOVAL at end of ENGINE section.
PISTON & ROD
NOTE: Mark piston cylinder location for reassembly reference.
Install pistons in original cylinder location.
Removal
1) Remove cylinder head. See CYLINDER HEAD in this article.
Remove oil pan. See OIL PAN REMOVAL at end of ENGINE section. Remove
ridge or deposits from cylinder bore.
2) Mark connecting rod and piston for cylinder
identification. Remove bearing cap. Remove piston and rod assembly.
CAUTION: Arrows on top of piston must point toward front of engine.
Oil squirt holes in connecting rod must face camshaft side
of engine.
Installation
1) Ensure ring end gap and side clearance are within
specification. See ENGINE SPECIFICATIONS tables. Install rings on
piston. Position ring end gaps at specified areas. See Fig. 5. Ring
gaps may vary 20 degrees from positions illustrated.
Page 62 of 1378
Fig. 5: Positioning Piston Ring Gaps
Courtesy of Chrysler Motors
2) Lubricate piston assembly and cylinder block. Install
piston assembly. Arrows on top of piston must face toward front of
engine and connecting rod oil squirt hole should face camshaft side of
Page 63 of 1378
engine.
3) Install bearings. Check oil clearance and connecting rod
side play clearance. Reverse removal procedure for remaining
components. Tighten bolts to specification.
Fitting Pistons
1) Determine cylinder taper, wear and out-of-roundness and
piston clearance. For cylinder specifications, see CYLINDER, PISTON &
ROD SPECIFICATIONS table. If taper or out-of-roundness are not within
specification, hone or bore cylinders for installation of new pistons.
2) Measure piston at right angle of the piston pin at the
center line of the pin. Compare reading to cylinder bore to determine
clearance. Mark fitted piston for cylinder location.
CYLINDER, PISTON & ROD SPECIFICATIONS TABLE
\
\
\
\
\
\
\
Application In. (mm)
Connecting Rod
Crankshaft Bore ................ 2.2080-2.2085 (56.083-56.095)
Pin Bore ......................... .9288-.9298 (23.591-23.616)
Cylinder Bore
Diameter
4.0L ......................... 3.8751-3.8775 (98.427-98.488)
4.2L ......................... 3.7501-3.7533 (95.252-95.334)
Out-of-Round ...................................... .001 (.02)
Taper ............................................. .001 (.02)
Piston Pin Bore Diameter ........... .9308-.9313 (23.642-23.655)
Piston Pin Diameter ................ .9304-.9309 (23.632-23.644)
Piston-to-Cylinder Clearance ..... .0009-.0017 (.022-.043)
\
\
\
\
\
\
PISTON PIN
NOTE: Note direction of arrows on piston and oil squirt hole in
connecting rod location prior to removal.
Removal
Position piston on Support (J-21872-1), Pin Pilot (J-21872-2\
)
and Driver (J-21872-3) on an arbor press. See Fig. 6. Note location of
piston pin through gauge window. Press piston pin from piston.
NOTE: Piston and pin must be at standard room temperature when
measuring fit. Piston pin should gravity-fall through the
piston at room temperature. Piston pin cannot be reused
after removal.
Inspection
Measure piston pin diameter, piston bore and connecting rod
bores. Replace components if not within specification. See CYLINDER,
PISTON & ROD SPECIFICATIONS table.
NOTE: Rod must be positioned on the piston so the oil squirt hole
faces the camshaft side of the engine when piston is
installed with arrow toward the front of the engine.
Installation
1) Insert pin pilot through piston and connecting rod. Place
assembly on support. Insert piston pin through the upper piston pin
bore and into connecting rod pin bore. See Fig. 6.
Page 65 of 1378
ROD BEARING
NOTE: Crankshaft journal diameters are indicated by a color coded
mark placed on the adjacent counterweight or cheek toward
the flanged (rear) end of crankshaft. Note color code to
determine proper bearing usage. Check oil clearance after
bearing installation.
Removal
Remove oil pan. See OIL PAN REMOVAL at end of ENGINE section.
Rotate crankshaft to position rod to be serviced at bottom of stroke.
Mark bearing cap and connecting rod. Remove bearing cap with bearing.
Push piston and rod assembly up to remove upper bearing.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Using Plastigage method, check bearing clearances. Replace
bearings as necessary to obtain correct clearance. Bearings are
available in standard and undersize application.
2) If required, different sized upper and lower bearings may
be installed to obtain correct oil clearance. Tighten bolts to
specification. Check rod side play. Rotate crankshaft to ensure
freedom of movement. Reverse removal procedure for remaining
components. Tighten bolts to specification.
NOTE: Avoid combining bearing inserts in excess of .001" (.02 mm)
difference in size.
MAIN BEARING
Removal
Remove oil pan. See OIL PAN REMOVAL at end of ENGINE section.
Ensure main bearing caps are marked for location. Remove bearing cap.
Rotate crankshaft to remove bearings. Note color code on edge of
bearing.
NOTE: Crankshaft main bearing journal diameters are indicated by a
color code. Color code is placed on the adjacent cheek
toward the flanged (rear) end of crankshaft for all except
the rear main. Rear main is color coded on the rear flange.
Note color code to determine proper bearing usage. Check oil
clearance after bearing installation.
Installation
1) Note color code on edge of bearings removed. Install
bearings. Ensure caps are installed in original location with arrow on
cap facing toward front of engine. Using Plastigage method, check
bearing clearances.
2) Replace bearings as necessary to obtain correct clearance.
Bearings are available in standard and undersize applications. If
required, different sized upper and lower bearings may be installed to
obtain correct oil clearance.
NOTE: If different sized bearings are used, odd sized bearings must
all be uniform in location (upper or lower). DO NOT use
bearings with a thickness difference exceeding
.001" (.02 mm).
3) Tighten bolts to specification. Check crankshaft end play.
See CRANKSHAFT END PLAY in this article. Rotate crankshaft to ensure
freedom of movement. Reverse removal procedure for remaining
components. Tighten bolts to specification.