wheel size JEEP CHEROKEE 1988 Service Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 1988, Model line: CHEROKEE, Model: JEEP CHEROKEE 1988Pages: 1378, PDF Size: 19.9 MB
Page 192 of 1378
\003
AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS
1988 J e ep C hero ke e
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85 C for 2 hours is generally considered a
maximum limit).
Page 278 of 1378
in the brake fluid.
4) Using proper sized rod, apply and release master cylinder
until no air bubbles exist in brake fluid flow. Once all air bubbles
are gone from master cylinder secure cap and install.
5) Bleeder tubes should be left installed on master cylinder
until master cylinder in installed. Master cylinder must be bled at
brake lines and wheels after installation.
Bleeding On Vehicle
1) Install master cylinder on vehicle after bench bleeding.
Remove bleeder lines and install brake lines. DO NOT fully tighten
brake lines at this time.
2) Slowly force brake pedal to the floor and hold in this
position. Tighten brake lines and release brake pedal. Repeat
procedure until no air bubbles exist at brake lines. Remaining wheel
cylinder or calipers may be require bleeding.
HYDRAULIC CONTROL VALVES
Hold Off Valve
1) Prior to the pressure tank bleeding procedure, the hold
off valve incorporated in the combination valve must be correctly
positioned. This allows brake fluid to flow through the combination
valve to the entire brake system.
2) The valve stem of the hold off valve may be retained using
tools available from Chrysler Motors (C-4121) or General Motors
(J-23709) during bleeding procedure. See Figs. 2 and 3. Remove valve
retainer once brake bleeding procedure is complete.
CAUTION: DO NOT use rigid clamp to position valve stem. Damage to
the valve assembly may result causing brake failure.
Fig. 2: Positioning Hold Off Valve
Courtesy of American Motors/Jeep Corp.
Page 309 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual \
\
\
\
\
\
\
Condition Code](/img/16/57037/w960_57037-308.png "JEEP CHEROKEE 1988 Service Repair Manual \
\
\
\
\
\
\
Condition Code")
\
\
\
\
\
\
\
Condition Code Procedure
Tire diameter incorrect,
affecting ABS or TCS ... A ............ Require replacement.
Tire pressure incorrect,
affecting ABS or TCS ... A .. Require repair or replacement.
Tire size incorrect,
affecting ABS or TCS ... A ............ Require replacement.
\
\
\
\
\
\
\
TOOTHED RINGS (TONE WHEEL)
NOTE: Copied from Drivetrain UIGs.
If the toothed ring requires replacement and cannot be
replaced as a separate component, replace the assembly of which the
ring is a part.
TOOTHED RING INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Alignment incorrect ..... B ............... Require repair or
replacement.
Bent .................... B ............ Require replacement.
Contaminated, affecting
performance ............. A ........ Require repair. Identify
and correct cause.
Cracked ................. B ............ Require replacement.
Loose ................... A ............. Require replacement
of worn parts.
Missing ................. C ............ Require replacement.
Number of teeth
incorrect .............. B ............ Require replacement.
Teeth broken ............ A ............ Require replacement.
Teeth damaged, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
VACUUM BOOSTERS
VACUUM BOOSTER INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Applies too much assist
(oversensitive) ........ A ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Auxiliary vacuum pump
inoperative ............ A ........... ( 1) Require repair or
replacement.
Check valve grommet
deteriorated, affecting
performance ............ A .. Require replacement of grommet.
Page 313 of 1378
to the conditions that follow, you may suggest rebuilding or
replacement of the other wheel cylinder (on the same axle) for
preventive maintenance, for example, the part is close to the end of
its useful life.
Determine the need to rebuild or replace based upon the
individual wheel cylinder conditions that follow.
WHEEL CYLINDER INSPECTION
\
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ..... Require replacement of bent
parts.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
corroded, affecting
structural integrity ... A . Require replacement of corroded
parts.
Attaching hardware
loose .................. A .. Require repair or replacement.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Bleeder port damaged (if
non-repairable) ........ A ............ Require replacement.
Bleeder screw broken off
in wheel cylinder (if non-
repairable) ............ A ........ (1) Require replacement.
Bleeder screw plugged ... A ........... ( 1) Require repair or
replacement of bleeder screw.
Bleeder screw seized .... A ........ ( 2) Require replacement.
Bore corroded (pitted) .. B ............ Require replacement.
Bore grooved ............ A ............ Require replacement.
Bore oversized .......... B ............ Require replacement.
Dust boot missing ....... C ..... Require replacement of dust
boot.
Dust boot torn .......... A . ( 3) Require replacement of dust
boot.
Leaking ................. A ....... ( 4) Require rebuilding or
replacement.
Piston corroded, affecting
performance ............ B ... Require replacement of piston
and rebuilding or replacement
of wheel cylinder.
Piston finish worn off .. B ... Require replacement of piston
and rebuilding or replacement
of wheel cylinder.
Piston stuck in bore .... A .... Require replacement of wheel
cylinder.
Loose ................... B .. Require repair or replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Only required if the hydraulic system must be opened.
( 2) - Seized is defined as bleeder screw that cannot be removed
after a practical attempt at removing. Only required if
the hydraulic system must be opened.
Page 322 of 1378
Fig. 5: Bleeding Master Cylinder
Courtesy of American Motors/Jeep Corp.
3) Fill master cylinder with clean brake fluid that meets DOT
3 specifications. Ensure that the end of bleeder tubes are submerged
in the brake fluid.
4) Using proper sized rod, apply and release master cylinder
until no air bubbles exist in brake fluid flow. Once all air bubbles
are gone from master cylinder secure cap and install.
5) Bleeder tubes should be left installed on master cylinder
until master cylinder in installed. Master cylinder must be bled at
brake lines and wheels after installation.
Bleeding On Vehicle
1) Install master cylinder on vehicle after bench bleeding.
Remove bleeder lines and install brake lines. DO NOT fully tighten
brake lines at this time.
2) Slowly force brake pedal to the floor and hold in this
position. Tighten brake lines and release brake pedal. Repeat
procedure until no air bubbles exist at brake lines. Remaining wheel
cylinder or calipers may be require bleeding.
HYDRAULIC CONTROL VALVES
Hold Off Valve
1) Prior to the pressure tank bleeding procedure, the hold
off valve incorporated in the combination valve must be correctly
positioned. This allows brake fluid to flow through the combination
valve to the entire brake system.
2) The valve stem of the hold off valve may be retained using
Page 370 of 1378
\003
DRIV E A XLE - F U LL F LO ATIN G
1988 J e ep C hero ke e
Drive Axles - Dana Full-Floating Axles
Jeep Front & Rear Drive Axles
DESCRIPTION
The axle assembly is an integral carrier type with hypoid
gear ring and pinion. Stamped steel cover is removable for inspection
and repair of differential. Vehicle loads are carried by axle
housings. Axle shafts of "full-floating" rear assemblies may be
removed without disturbing wheel bearings.
Drive pinion depth, pinion bearing preload and differential
side bearing preload are all set by shims.
See LOCKING HUB and 4WD STEERING KNUCKLE articles in this
section for removal and installation procedures for these front drive
axle component parts.
AXLE RATIO & IDENTIFICATION
A metal tag on axle is stamped with gear ratio, part numbers
and limited slip identification. To determine drive axle ratio, refer
to MODEL IDENTIFICATION BY RING GEAR SIZE table.
MODEL IDENTIFICATION BY RING GEAR SIZE
\
\
\
\
\
Model Ring Gear Diameter
44 ....................................... 8.50"
60 ....................................... 9.75"
61 ....................................... 9.75"
70 ...................................... 10.50"
80 ...................................... 11.25"
\
\
\
\
\
FRONT HUB, BEARING, SPINDLE & AXLE SHAFT R & I
FRONT HUB BEARING ADJUSTING SPECIFICATIONS \
\
\
\
\
Application ( 1) Ft. Lbs. (N.m)
Adjusting Nut
Step 1 ............................... 50 (68)
Step 2 .......................... Back Off 20
Lock Nut ............................... 50 (68)
( 1) - While Rotating Hub.
\
\
\
\
\
REMOVAL (CHEROKEE, COMANCHE & WAGONEER)
1) Raise and support vehicle. Remove tire and wheel assembly.
Remove disc brake caliper and support out of way.
2) Match mark disc rotor and hub and remove disc rotor.
Remove cotter pin, nut lock and axle hub nut. Remove hub-to-knuckle
bolts. Pull hub assembly off axle shaft. Pull axle shaft through
knuckle to remove. Inspect axle shaft "U" joint and shaft splines for
wear. Replace as necessary.
3) Press hub out of bearings. Remove seals and bearings.
Page 429 of 1378
Vibration can come from many sources. Before overhauling
driveline, check other sources of possible vibration as follows:
* Tires and wheels - Check tire inflation and wheel balance.
Check for foreign objects in tread, damaged tread, mismatched
tread patterns or incorrect tire size.
* Center Bearing - Tighten drive shaft center bearing
mounting bolts. If bearing insulator is deteriorated or
oil-soaked, replace it.
* Engine & Transmission Mountings - Tighten mounting bolts.
If mountings are deteriorated, replace them.
* Drive Shaft - Check drive shaft for damage or dents that
could affect balance. Check for undercoating adhering to
shafts. If present, clean shafts thoroughly.
* Universal Joints - Check for foreign material stuck in
joints. Check for loose bolts and worn bearings.
ADJUSTMENTS
DRIVE SHAFT PHASING
One-Piece Shafts
Check that flanges on either end of drive shaft are in same
plane. Often there are arrows on slip joint and drive shaft to aid in
alignment. See Fig. 2. If flanges are not in same plane, disassemble
universal joint and align.
Fig. 2: Slip Joint Alignment Arrows
Align arrows for proper shaft phasing.
2-Piece Shafts
1) All General Motors models with 32 splines use keys on
spline and slip joint, which can only mate in correct position. On
most models with 2-piece shafts, proper phasing is accomplished by
keys on spline and slip joint.
Page 902 of 1378
MAIN TE N AN CE IN FO RM ATIO N
1988 J e ep C hero ke e
1984-88 MAINTENANCE
AMC/Jeep Maintenance Information
Jeep; Cherokee,
Wagoneer
* PLEASE READ THIS FIRST *
NOTE: For scheduled maintenance intervals and the related fluid
capacities, fluid specifications and labor times for major
service intervals, see SCHEDULED SERVICES article below:
* SCHEDULED SERVICES - GASOLINE
* SCHEDULED SERVICES - DIESEL ENGINES - NORMAL (1985-87)
Warranty information and specifications for fluid
capacities, lubrication specifications, wheel and tire size,
and battery type are covered in this article.
MODEL IDENTIFICATION
VIN LOCATION
The Vehicle Identification Number (VIN) is located on the
left side of the dash panel at the base of the windshield. The VIN
chart explains the code characters.
VIN CODE ID EXPLANATION
Numbers preceding the explanations in the legend below refer
to the sequence of characters as listed on VIN identification label.
See VIN example below.
\
\
\
\
\
\
(VIN) 1 J C U N 7 7 1 X G T 0 0 0 0 0 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
\
\
\
\
\
\
1 - Manufacturing Country
1
* United States
2 - Company/Make
J * American Motors/Jeep
3 - Type
C * Multi-Purpose Vehicle
D * Incomplete Vehicle
E * Export, LHD
F * Export, RHD
4 - Engine Type
B * 2.1L (128 CID) 4-Cylinder Turbo (Diesel) (001B) (1985-87)
H * 2.5L (150 CID) 4-Cylinder TBI (Gasoline) (001H) (1986-88)
U * 2.5L (150 CID) 4-Cylinder 1-Bbl. (Gasoline) (001U) (1984-85)
Y * 2.5L (150 CID) 4-Cylinder 1-Bbl. (Export) (001Y) (1984-85)
W * 2.8L (171 CID) V6 2-Bbl. (Gasoline) (001W) (1984-86)
M * 4.0L (242 CID) I-6 (Gasoline) (001M) (1987-88)
Page 914 of 1378
Command-Trac .............................. 2.2 Pts. (1.0L)
Drive Axles (3)
Front ....................................... 2.5 Pts. (1.2L)
Front (Disconnect Housing) ( 4) ............. 5.0 Ozs. (0.15L)
Rear ........................................ 2.5 Pts. (1.2L)
Rear (Trac-Lok) ( 5) ......................... 2.5 Pts. (1.2L)
( 1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
( 2) - Includes 2.3 Qts. for coolant recovery bottle.
( 3) - Fill to bottom of filler plug hole.
( 4) - Add 5 Ozs. of gear lubricant through indicator switch hole.
( 5) - Add 2 Ozs. of Limited-Slip differential lubricant additive
first, then add new fluid.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
WHEEL & TIRE SPECIFICATIONS TABLE\
\
\
\
\
\
Wheel Size Tire Size
Cherokee
15x6 & 15x7 (Aluminum Or Steel) ............. P195/75R15
15x6 & 15x7 (Aluminum Or Steel) ............. P205/75R15
15x6 & 15x7 (Aluminum Or Steel) ............. P215/75R15
15x6 & 15x7 (Aluminum Or Steel) ............. P225/75R15
Wagoneer
15x6 (Aluminum/Steel) ....................... P205/75R15
All Models
16-Inch Wheels ...................... Compact Spare Tire
\
\
\
\
\
\
TIRE REPLACEMENT
CAUTION: Always ensure all 4 tires on the vehicle are the same size,
except when using the temporary spare. The use of
mismatched tires may cause unpredictable handling.
Replacing original tires with tires of a different size may
result in false speedometer and odometer indications.
TIRE INFLATION
The tire specification decal is located in the glove box.
WHEEL TIGHTENING
Tighten the lug nuts firmly in a crisscross pattern as shown
in Fig. 11 . Tighten to 95 ft. lbs (129 N.m). Always position wheel
locking nut opposite valve stem in position indicated. See Fig. 11.
Fig. 11: Wheel Locking Nut Location
Courtesy of American Motors Corp.
Page 939 of 1378
\003
PR E-A LIG NM EN T C HEC KS
1988 J e ep C hero ke e
Wheel Alignment
PRE-ALIGNMENT INSPECTION PROCEDURES
PRE-ALIGNMENT CHECKS
Before making wheel alignment adjustment, perform the
following checks:
1) Tires should be equal in size and runout must not be
excessive. Tires and wheels should be in balance, and inflated to
manufacturer's specifications.
2) Wheel bearings must be properly adjusted. Steering linkage
and suspension must not have excessive looseness. Check for wear in
tie rod ends and ball joints.
3) Steering gear box must not have excessive play. Check and
adjust to manufacturer's specifications.
4) Vehicle must be at curb height with full fuel load and
spare tire in vehicle. No extra load should be on vehicle.
5) Vehicle must be level with floor and with suspension
settled. Jounce front and rear of vehicle several times and allow it
to settle to normal curb height.
6) If steering wheel is not centered with front wheels in
straight-ahead position, correct by shortening one tie rod adjusting
sleeve and lengthening opposite sleeve equal amounts.
7) Ensure wheel lug nuts are tightened to torque
specifications.