brake JEEP CHEROKEE 1988 Service Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 1988, Model line: CHEROKEE, Model: JEEP CHEROKEE 1988Pages: 1378, PDF Size: 19.9 MB
Page 83 of 1378
Resistance value should be about 22 ohms. Measure resistance between
either terminal and battery negative post. Resistance value should be
infinite. If resistance values are not as specified, replace relay. If
okay, reconnect electrical connectors.
2) Disconnect electrical connector from "SOL" terminal.
Connect voltmeter between terminal and battery negative post. While
observing voltmeter, turn ignition switch to "START" position. If 12
volts is not indicated, check and repair wiring harness, bulkhead
connector, and/or ignition switch. If battery voltage is present, go
to next step.
3) If battery voltage is present, but starter relay does not
work, place transmission in Park (Neutral for man. trans.) and apply
parking brake. Disconnect electrical connector from terminal "I" (Dark
Green wire) and apply battery voltage to terminal. Using a jumper
wire, touch terminal "G" to ground. If relay does not click, replace
relay. If relay does click, repair ground circuit.
Fig. 7: Design & Function of Relays
REMOVAL & INSTALLATION
Page 90 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual AB BREVIA TIO NS
1988 J e ep C hero ke e
GENERAL INFORMATION
COMMONLY USED ABBREVIATION
"A" ABBREVIATION TABLE
"A" ABBREVIATION TABLE \](/img/16/57037/w960_57037-89.png "JEEP CHEROKEE 1988 Service Repair Manual AB BREVIA TIO NS
1988 J e ep C hero ke e
GENERAL INFORMATION
COMMONLY USED ABBREVIATION
\"A\" ABBREVIATION TABLE
\"A\" ABBREVIATION TABLE \")
AB BREVIA TIO NS
1988 J e ep C hero ke e
GENERAL INFORMATION
COMMONLY USED ABBREVIATION
"A" ABBREVIATION TABLE
"A" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
A Amperes
A/C Air Conditioning
A/T Automatic Transmission/Transaxle
AAP Auxiliary Accelerator Pump
AB Air Bleed
ABCV Air Bleed Control Valve
ABDC After Bottom Dead Center
ABRS Air Bag Restraint System
ABS Anti-Lock Brake System
AC Alternating Current
ACC A/C Clutch Compressor
ACCS A/C Cycling Switch
ACCUM Accumulator
ACCY Accessory
ACT Air Charge Temperature Sensor
ACV Thermactor Air Control Valve
ADJ Adjust or Adjustable
ADV Advance
AFS Airflow Sensor
AI Air Injection
AIR or A.I.R. Air Injection Reactor
AIS Air Injection System
ALCL Assembly Line Communications Link
ALDL Assembly Line Diagnostic Link
ARC Automatic Ride Control
ASCD Automatic Speed Control Device
ASCS Air Suction Control Solenoid
ASD Auto Shutdown
ASDM Air Bag System Diagnostic Module
ASV Air Suction Valve
ATC Automatic Temperature Control
ATDC After Top Dead Center
ATF Automatic Transmission Fluid
ATS Air Temperature Sensor
AXOD Automatic Transaxle Overdrive
Abs. Absolute
Accy. Accessory
Alt. Alternator or Altitude
Amp. Ampere
Assy. Assembly
Auto. Automatic
Aux. Auxiliary
Avg. Average
\
\
\
\
\
\
\
\f
"B" ABBREVIATION TABLE
"B" ABBREVIATION TABLE
Page 91 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION](/img/16/57037/w960_57037-90.png "JEEP CHEROKEE 1988 Service Repair Manual \
\
\
\
\
\
\
ABBREVIATION DEFINITION")
\
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
B/P Backpressure
BAC By-Pass Air Control
BAP Barometric Absolute Pressure Sensor
BARO Barometric
BBDC Before Bottom Dead Center
BCM Body Control Module
BDC Bottom Dead Center
BHP Brake Horsepower
BLK Black
BLU Blue
BMAP Barometric & Manifold Absolute Pressure Sensor
BOO Brake On-Off Switch
BP Barometric Pressure sensor
BPS Barometric Pressure Sensor
BPT Backpressure Transducer
BRN Brown
BTDC Before Top Dead Center
BTU British Thermal Unit
BVSV Bimetallic Vacuum Switching Valve
Baro. Barometric
Batt. Battery
Bbl. Barrel (Example: 4-Bbl.)
Blst. Ballast
Blwr. Blower
Brkr. Breaker
\
\
\
\
\
\
\
\f
"C" ABBREVIATION TABLE
"C" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
C Celsius (Degrees)
C(3) I Computer Controlled Coil Ignition
C(4) Computer Controlled Catalytic Converter
CANP Canister Purge solenoid
CARB California Air Resources Board
CAT Catalytic Converter
CB Circuit Breaker
CBD Closed Bowl Distributor
CBVV Carburetor Bowl Vent Valve
cc Cubic Centimeter
CCC Computer Command Control
CCD Computer Controlled Dwell
CCM Central Control Module
CCO Converter Clutch Override
CCOT Cycling Clutch Orifice Tube
CCW Counterclockwise
CDI Capacitor Discharge Ignition
CEC Computerized Engine Control
CFI Central Fuel Injection
CID Cubic Inch Displacement
CID Cylinder Identification sensor
CIS Continuous Injection System
CIS-E Continuous Injection System-Electronic
CKT Circuit
CLR Clear
CNG Compressed Natural Gas
Page 93 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual \
\b\
\
\
\
\
\
EAC Electric Assist Choke](/img/16/57037/w960_57037-92.png "JEEP CHEROKEE 1988 Service Repair Manual \
\b\
\
\
\
\
\
EAC Electric Assist Choke")
\
\b\
\
\
\
\
\
EAC Electric Assist Choke
EACV Electric Air Control Valve
EBCM Electronic Brake Control Module
ECA Electronic Control Assembly
ECAT Electronically Controlled Automatic Transaxle
ECM Electronic Control Module
ECT Engine Coolant Temperature Sensor
ECU Electronic Control Unit or Engine Control Unit
EDF Electric Drive Fan relay assembly
EDIS Electronic Distributorless Ignition System
EEC Electronic Engine Control
EECS Evaporative Emission Control System
EEPROM Electronically Erasable PROM
EFE Early Fuel Evaporation
EFI Electronic Fuel Injection
EGO Exhaust Gas Oxygen sensor (see HEGO)
EGR Exhaust Gas Recirculation system
EGRC EGR Control solenoid or system
EGRV EGR Vent solenoid or system
EMR Emission Maintenance Reminder Module
ESA Electronic Spark Advance
ESC Electronic Spark Control
EST Electronic Spark Timing
ETR Emergency Tensioning Retractor
EVAP Fuel Evaporative System
EVIC Electronic Vehicle Information Center
EVO Electronic Variable Orifice
EVP EGR Valve Position Sensor
EVR EGR Valve Regulator
EVRV Electronic Vacuum Regulator Valve
Elect. Electronic
Eng. Engine
Evap. Evaporative
Exc. Except
\
\
\
\
\
\
\
\f
"F" ABBREVIATION TABLE
"F" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
F Fahrenheit (Degrees)
F/B Fuse Block
FBC Feedback Carburetor
FI Fuel Injector or Fuel Injection
FICD Fast Idle Control Device
FIPL Fuel Injector Pump Lever
FP Fuel Pump
FPM Fuel Pump Monitor
FPR-VSV Fuel Pressure Regulator Vacuum Switching Valve
FWD Front Wheel Drive
Fed. Federal
Ft. Lbs. Foot Pounds
\
\
\
\
\
\
\
\f
"G" ABBREVIATION TABLE
"G" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
Page 97 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual "P" ABBREVIATION TABLE
"P" ABBREVIATION TABLE \
\
\
\
\
\
\](/img/16/57037/w960_57037-96.png "JEEP CHEROKEE 1988 Service Repair Manual \"P\" ABBREVIATION TABLE
\"P\" ABBREVIATION TABLE \
\
\
\
\
\
\")
"P" ABBREVIATION TABLE
"P" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
"P" Park
P/C Printed Circuit
P/N Park/Neutral
P/S Power Steering
PAV Pulse Air Valve
PC-SOL Purge Control Solenoid
PCM Powertrain Control Module
PCS Purge Control Solenoid
PCSDM Passenger Compartment Sensor/Diagnostic Module
PCV Positive Crankcase Ventilation
PFE Pressure Feedback EGR sensor or circuit
PFI Port Fuel Injection (see MA SEFI)
PGM-CARB Programmed Carburetor
PGM-FI Programmed Fuel Injection
PIP Profile Ignition Pickup
PNK Pink
PPL Purple
PRNDL Park Reverse Neutral Drive Low
PROM Programmable Read-Only Memory
psi Pounds Per Square Inch
PSPS Power Steering Pressure Switch
PTC Positive Temperature Coefficient
PTO Power Take-Off
PWR GND Power Ground circuit
Pkg. Package
Press. Pressure
Prog. Programmed or Programmable
Pts. Pints
Pwr. Power
\
\
\
\
\
\
\
\f
"Q" ABBREVIATION TABLE
"Q" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
Qts. Quarts
\
\
\
\
\
\
\
\f
"R" ABBREVIATION TABLE
"R" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
RABS Rear Anti-Lock Brake System
RAC Remote Accessory Control
RAM Random Access Memory
RAP Retained Accessory Power
RECIRC Recirculation
RED Red
RH Right Hand
ROM Read Only Memory
RPM Revolutions Per Minute
Page 98 of 1378
RVB Rear Vacuum Break
RWAL Rear Wheel Anti-Lock Brake
RWD Rear Wheel Drive
Recirc. Recirculate or Recirculation
Reg. Regulator
Rly. Relay
\
\
\
\
\
\
\
\f
"S" ABBREVIATION TABLE
"S" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
SAW Spark Angle Word
SBC Single Bed Converter
SBEC Single Board Engine Controller
SC Super Charged
SCC Spark Control Computer
SCS Air Suction Control Solenoid
SDM Supplemental Restraint System Diagnostic Module
SDU SRS Diagnostic Unit
SEN Sensor
SES Service Engine Soon
SFI Sequential (Port) Fuel Injection
SIG RTN Signal Return circuit
SIL Shift Indicator Light
SIR Supplemental Inflatable Restraint
SMEC Single Module Engine Controller
SOHC Single Overhead Cam
SOL or Sol. Solenoid
SPFI Sequential Port Fuel Injection
SPK Spark Control
SPOUT Spark Output Signal
SRS Supplemental Restraint System (Air Bag)
SS 3/4-4/3 Shift Solenoid circuit
SSI Solid State Ignition
STAR Self-Test Automatic Readout
STI Self Test Input circuit
STO Self-Test Output
SUB-O2 Sub Oxygen Sensor
Sen. or Sens. Sensor
Sol. Solenoid
Sprchg. Supercharger
Strg. Steering
Susp. Suspension
Sw. Switch
Sys. System
\
\
\
\
\
\
\
\f
"T" ABBREVIATION TABLE
"T" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
T.V. Throttle Valve
TAB Thermactor Air By-Pass
TAC Thermostatic Air Cleaner
TAD Thermactor Air Diverter
TAN Tan
TBI Throttle Body Injection
Page 118 of 1378
HEATER HOSES
HIGH PRESSURE RELIEF VALVES (HPRV)
IDLERS
IN-LINE FILTERS
METAL FITTINGS
METAL LINES
MIX AND AIR CONTROL DOORS (BLEND DOORS)
O-RINGS
ORIFICE TUBES
PILOT-OPERATED ABSOLUTES (POAS)
PLENUMS
PRESSURE CONTROL VALVES
PRESSURE SENSORS
PULLEYS
RADIATORS
RECEIVER-DRIERS
REFRIGERANT
REFRIGERANT OIL
RELAYS
SEALS
SERVICE PORTS
SPRING LOCK COUPLINGS
SUCTION THROTTLING VALVES (STVS)
SWITCHES (ELECTRICAL)
TENSIONERS
THERMISTORS AND PRESSURE SENSORS
THERMOSTATS AND HOUSINGS
VACUUM HOSES AND TUBES
VACUUM RESERVOIRS
VACUUM TUBES
VALVES IN RECEIVER (VIRS)
WATER PUMPS (ELECTRIC AUXILIARY)
WIRING HARNESSES AND CONNECTORS
MOTORIST ASSURANCE PROGRAM (MAP)
OVERVIEW
The Motorist Assurance Program is the consumer outreach
effort of the Automotive Maintenance and Repair Association, Inc.
(AMRA). Participation in the Motorist Assurance Program is drawn from
retailers, suppliers, independent repair facilities, vehicle
manufacturers and industry associations.
Our organization's mission is to strengthen the relationship
between the consumer and the auto repair industry. We produce
materials that give motorists the information and encouragement to
take greater responsibility for their vehicles-through proper,
manufacturer-recommended, maintenance. We encourage participating
service and repair shops (including franchisees and dealers) to adopt
(1) a Pledge of Assurance to their Customers and (2) the Motorist
Assurance Program Standards of Service. All participating service
providers have agreed to subscribe to this Pledge and to adhere to the
promulgated Standards of Service demonstrating to their customers that
they are serious about customer satisfaction.
These Standards of Service require that an inspection of the
vehicle's (problem) system be made and the results communicated to the\
customer according to industry standards. Given that the industry did
not have such standards, the Motorist Assurance Program successfully
promulgated industry inspection communication standards in 1994-95 for
the following systems: Exhaust, Brakes, ABS, Steering and Suspension,
Engine Maintenance and Performance, HVAC, and Electrical Systems.
Further, revisions to all of these inspection communication standards
Page 119 of 1378
are continually republished. In addition to these, standards for Drive
Train and Transmissions have recently been promulgated. Participating
shops utilize these Uniform Inspection & Communication Standards as
part of the inspection process and for communicating their findings to
their customers.
The Motorist Assurance Program continues to work
cooperatively and proactively with government agencies and consumer
groups toward solutions that both benefit the customer and are
mutually acceptable to both regulators and industry. We maintain the
belief that industry must retain control over how we conduct our
business, and we must be viewed as part of the solution and not part
of the problem. Meetings with state and other government officials
(and their representatives), concerned with auto repair and/or
consumer protection, are conducted. Feedback from these sessions is
brought back to the association, and the program adjusted as needed.
To assure auto repair customers recourse if they were not
satisfied with a repair transaction, the Motorist Assurance Program
offers mediation and arbitration through MAP/BBB-CARE and other non-
profit organizations. MAP conducted pilot programs in twelve states
before announcing the program nationally in October, 1998. During the
pilots, participating repair shops demonstrated their adherence to the
Pledge and Standards and agreed to follow the UICS in communicating
the results of their inspection to their customers. To put some
"teeth" in the program, an accreditation requirement for shops was
initiated. The requirements are stringent, and a self-policing method
has been incorporated which includes the "mystery shopping" of
outlets.
We welcome you to join us as we continue our outreach... with
your support, both the automotive repair industry and your customers
will reap the benefits. Please visit MAP at our Internet site www.
motorist.org or contact us at:
1444 I Street, NW Suite 700
Washington, DC 20005
Phone (202) 712-9042 Fax (202) 216-9646
January 1999
MAP UNIFORM INSPECTION GENERAL GUIDELINES
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
It is MAP policy that all exhaust, brake, steering,
suspension, wheel alignment, drive-line, engine performance and
maintenance, and heating, ventilation and air conditioning, and
electrical services be offered and performed under the standards and
procedures specified in these sections.
Before any service is performed on a vehicle, an inspection
of the appropriate system must be performed. The results of this
inspection must be explained to the customer and documented on an
inspection form. The condition of the vehicle and its components will
indicate what services/part replacements may be "Required" or
"Suggested". In addition, suggestions may be made to satisfy the
requests expressed by the customer.
When a component is suggested or required to be repaired or
replaced, the decision to repair or replace must be made in the
customer's best interest, and at his or her choice given the options
available.
This section lists the various parts and conditions that
indicate a required or suggested service or part replacement.
Although this list is extensive, it is not fully inclusive. In
addition to this list, a technician may make a suggestion. However,
any suggestions must be based on substantial and informed experience,
Page 120 of 1378
or the vehicle manufacturer's recommended service interval and must be
documented.
Some conditions indicate that service or part replacement is
required because the part in question is no longer providing the
function for which it is intended, does not meet a vehicle
manufacturer's design specification or is missing.
Example:
An exhaust pipe has corroded severely and has a hole in it
through which exhaust gases are leaking. Replacement of the
exhaust pipe in this case is required due to functional
failure.
Example:
A brake rotor has been worn to the point where it measures
less than the vehicle manufacturer's discard specifications.
Replacement of the rotor is required because it does not meet
design specifications.
Some conditions indicate that a service or part replacement
is suggested because the part is close to the end of its useful life
or addresses a customer's need, convenience or request. If a
customer's vehicle has one of these conditions, the procedure may be
only to suggest service.
Example:
An exhaust pipe is rusted, corroded or weak, but no leaks are
present. In this case, the exhaust pipe has not failed.
However, there is evidence that the pipe may need replacement
in the near future. Replacement of the pipe may be suggested
for the customer's convenience in avoiding a future problem.
Example:
The customer desires improved ride and/or handling, but the
vehicle's shocks or struts have not failed. In this case,
replacement may be suggested to satisfy the customer's
wishes. In this case, replacement of the shocks or struts may
not be sold as a requirement.
A customer, of course, has the choice of whether or not a
shop will service his or her vehicle. He or she may decide not to
follow some of your suggestions. When a repair is required, a MAP shop
must refuse partial service on that system if, in the judgment of the
service provider, proceeding with the work could create or continue an
unsafe condition. When a procedure states that required or suggested
repair or replacement is recommended, the customer must be informed of
the generally acceptable repair/replacement options whether or not
performed by the shop.
When presenting suggested repairs to the customer, you must
present the facts, allowing the customer to draw their own conclusions
and make an informed decision about how to proceed.
The following reasons may be used for required and suggested
services. These codes are shown in the "Code" column of the MAP
Uniform Inspection & Communications Standards that follow:
Reasons to Require Repair or Replacement
A - Part no longer performs intended purpose
B - Part does not meet a design specification (regardless of
performance)
C - Part is missing
NOTE: When a repair is required, the shop must refuse partial
Page 192 of 1378
\003
AN TI- L O CK B RAK E S A FE TY P R EC AU TIO NS
1988 J e ep C hero ke e
GENERAL INFORMATION
Anti-Lock Brake Safety Precautions
* PLEASE READ THIS FIRST *
This article is intended for general information purposes
only. This information may not apply to all makes and models. If
vehicle is equipped with Anti-Lock Brake System (ABS), refer to
appropriate ANTI-LOCK BRAKE SYSTEM article in the BRAKES section for
description, operation, depressurizing, testing, system bleeding,
trouble shooting and servicing of specific system.
WARNING: Failure to depressurize ABS could lead to physical injury.
ANTI-LOCK BRAKE SAFETY PRECAUTIONS
WARNING: Failure to depressurize ABS could lead to physical injury.
* NEVER open a bleeder valve or loosen a hydraulic line
while ABS is pressurized.
* NEVER disconnect or reconnect any electrical connectors
while ignition is on. Damage to ABS control unit may result.
* DO NOT attempt to bleed hyudarulic system without first
referring to the appropriate ANTI-LOCK BRAKE SYSTEM article
in the BRAKES section.
* Only use specially designed brake hoses/lines on ABS equipped
vehicles.
* DO NOT tap on speed sensor components (sensor, sensor rings).
Sensor rings must be pressed into hubs, NOT hammered into
hubs. Striking these components can cause demagnetization or
a loss of polarization, affecting the accuracy of the speed
signal returning to the ABS control unit.
* DO NOT mix tire sizes. Increasing the width, as long as tires
remain close to the original diameter, is acceptable. Rolling
diameter must be identical for all 4 tires. Some
manufacturers recommend tires of the same brand, style and
type. Failure to follow this precaution may cause inaccurate
wheel speed readings.
* DO NOT contaminate speed sensor components with grease. Only
use recommended coating, when system calls for an
anti-corrosion coating.
* When speed sensor components have been removed, ALWAYS check
sensor-to-ring air gaps when applicable. These specifications
can be found in each appropriate article.
* ONLY use rocommended brake fluids. DO NOT use silicone brake
fluids in an ABS equipped vehicle.
* When instlling transmittion devices (CB's, telephones, etc.)
on ABS equipped vehicles, DO NOT locate the antenna near the
ABS control unit (or any control unit).
* Disconnect all on-board computers, when using electric
welding equipment.
* DO NOT expose the ABS control unit to prolonged periods of
high heat (185
F/85 C for 2 hours is generally considered a
maximum limit).