lock JEEP CJ 1953 User Guide

[x] Cancel search | Manufacturer: JEEP, Model Year: 1953, Model line: CJ, Model: JEEP CJ 1953
Pages: 376, PDF Size: 19.96 MB

Load previous 10 pages

Page 33 of 376

JEEP CJ 1953 User Guide
Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

C

FIG.
C-2
7—FAN
BELT
—
DAUNTLESS
V-6
ENGINE
e. Adjust mixture by turning idle mixture screws
out (counterclockwise) until a loss of engin

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

C

FIG.
C-2
7—FAN
BELT
—
DAUNTLESS
V-6
ENGINE
e. Adjust mixture by turning idle mixture screws
out (counterclockwise) until a loss of engine speed
is indicated; then, slowly
turn
both mixture screws

in
clockwise (leaner) until maximum speed (RPM)
is reached. Continue turning in (clockwise) until a slight drop in speed (RPM) is noted. Make certain
both mixture screws are adjusted equally.
This
will

ensure a "lean as possible" mixture adjustment.

Readjust
idle
stop
screw to idle engine at the
specified
R.P.M.

Note:
This
method of adjusting idle mixture must
be used to keep hydrocarbon and carbon monoxide
emissions to a minimum.

Note:
No fast idle speed adjustment is required.

Fast
idle is controlled by the curb idle speed ad justment screw. If the curb idle speed is correctly set, the fast idle speed
will
be correct.
C-26.
Dash
Pot
Adjustment

Refer
to Section
E, Par.
E-44 for proper carburetor

dash
pot adjustment procedure.

C-27.
Check
Fan
Belt

The
fan belt drives the fan, alternator, and water

pump.
See Fig. C-27.

Inspect
the fan belt for serviceability and proper
tension. The tension should be checked with the
Belt
Tension Gauge, W-283. The correct tension on a used belt is 70 to 80 pounds [31,7 a 36,2 kg.]

and
on a new belt 110 to 120 pounds [49,8 a 54,5 kg.]. When preparing for delivery of new car,
the belt strand tension should be 80 to 110 pounds [36,2 a 49,8 kg.]. When installing a new belt, adjust
the strand tension 110 to 120 pounds [49,8 a 54,5 kg.].

Adjust
the fan belt tension by loosening the clamp
bolt on the alternator brace and swinging the alter

nator
away from the engine until proper belt ten
sion is obtained.
Then
tighten the clamp bolt.

Note:
If no
gauge
is available approximate correct
tension is obtained when the thumb pressure mid
way between the pulleys causes the belt to flex
y%
inch
[IV4
cm.].

C-28.
ROAD TEST VEHICLE

After
completing the tune-up, road
test
the vehicle for power and overall performance. Make neces
sary
adjustments.

Note:
Engine run on or "dieseling" is a condition

in
which combustion continues to take place after
the normal ignition
spark
from the distributor has
been shut off by turning off the ignition switch. It is generally caused by excessive engine idle speed

in
combination with retarded ignition timing, en gine heat soak or the use of low octane fuel.

Should
engine dieseling (engine running after igni
tion key is turned off) be experienced on V-6 engine equipped vehicles, installation of Idle Stop
Valve
Kit
Part
No. 991722
will
correct the

difficulty.
33

Page 35 of 376

JEEP CJ 1953 User Guide
C-30.
TUNE-UP
SPECIFICATIONS

ITEM

BATTERY:
Voltage
Terminal
Ground Specific Gravity:
Fully
Charged Recharge at

Load
Test, minimum:
12-Volt Battery. .

SPARK PLUGS:

Make and Model

Page 37 of 376

JEEP CJ 1953 User Guide
Jeep9
UNIVERSAL SERIES SERVICE
MANUAL

D HURRICANE
F4
ENGINE

Contents

SUBJECT
PAR.

GENERAL...
D-l Description D-2

Engine
Ground Strap D-4

Engine
Mountings D-3

ENGINE REMOVAL
D

'Jeep9
UNIVERSAL SERIES SERVICE
MANUAL

D HURRICANE
F4
ENGINE

Contents

SUBJECT
PAR.

GENERAL...
D-l Description D-2

Engine
Ground Strap D-4

Engine
Mountings D-3

ENGINE REMOVAL
D-5
ENGINE DISASSEMBLY
D-6
Camshaft
.......
D-28
Clutch
D-24

Crankshaft.
D-26
Crankshaft
Pulley. D-l2
Cylinder
Head. .D-17
Distributor.
.D-13

Exhaust
Manifold D-8
Exhaust
Valves and Springs D-2
7

Flywheel.
. D-25
Front
End Plate D-23
Oil
Filler
Tube D-9

Oil
Gallery Plugs D-30

Oil
Pan. . ...D-19

Oil
Pump D-l4
Piston and Connecting Rods. . . D-20
Ream
Cylinder Bore Ridges. D-l8

Rocker
Arm Assemblies D-l6 Thermostat D-ll

Timing
Gear
Cover . . D-21

Timing
Gears D-22

Valve
Tappets D-29
Ventilation Valve D-l5
Water
Outlet Fitting D-10

Water
Pump D-7

ENGINE INSPECTION
AND
REPAIR.
.D-31
Camshaft
and Bearings. D-51
Camshaft
End-Play
. . .D-53

Camshaft
Front Bearing Replacement..... D-52
Checking
Connecting Rod
Crank
Pins D-42

Checking
Crankshaft Alignment .
.
D-40
Checking
Main Bearing Journals. D-41

Cleaning.
. D-33 Connecting Rod Bearing Inspection D-48
Connecting Rod Bearings D-47 Connecting Rod Side Play D-50

Core
Hole Expansion Plug D-72
Crankshaft
.
.
D-38, 39

Crankshaft
Main Bearing Inspection D-44

Crankshaft
Main Bearings D-43

Crankshaft
Rear
Bearing Seal D-63
Cylinder
Block D-32

Cylinder
Bores D-35

Cylinder
Head. . . D-73

Exhaust
Valve Seat Insert Replacement. .
.
D-60
Fitting
Crankshaft Main Bearings

Using
Plastigage
D-45

Fitting
Crankshaft Main Bearings
Using
Shim Stock D-46

Floating
Oil Intake D-64

Flywheel.
. . .D-67

Flywheel
Housing D-71
SUBJECT
FAR.

Flywheel
Inspection. D-6 8

Flywheel
Pilot Bushing D-70 Inspection D-3 4
Inspection of Valves, Springs and Guides. .D-57
Installing
Connecting Rod Bearings....... D-49

Oil
Pan D-66
Oil
Pump D-65
Piston Ring Application
Chart
D-3 7
Pistons, Rings, and Connecting Rods..... D-36

Refacing
Valves
.
D-58

Ring
Gear
Replacement D-69
Rocker
Arm Shaft Disassembly. D-75, 76

Rocker
Arm Shaft Reassembly.
.
D-77
Rocker
Arms D-74
Tappets and Cover. . D-62
Timing
Gears and Cover D-54, 55

Valve
Guide Replacement D-61
Valve
Seat Inspection and Refacing D-59

Valve,
Springs and Guides D-56

ENGINE REASSEMBLY
D-78
Camshaft
and
Thrust
Plate .D-81
Camshaft
Timing
Gear
D-91

Check
Crankshaft
End-Play.
............D-83
Clutch.
...D-89

Crankshaft
and Bearings................ D-82

Crankshaft
Pulley D-96

Crankshaft
Rear
Bearing Seal.. .
.
D-85
Crankshaft
Timing
Gear
D-84

Cylinder
Head D-98
Distributor
D-l
00

Flywheel
®. . .. D-87
Flywheel
Housing D-88

Front
End Plate D-86
Manifold.......
D-101

Oil
Filler
Tube D-102

Oil
Gallery Plug. D-79
Oil
Pan. D-97

Oil
Pump D-93
Pistons and Connecting Rods D-95
Rocker
Arm Assembly D-99

Spark
Plugs. .D-100
Tappets D-80
Timing
Gear
Cover D-94

Timing
Gear
Oil Jet D-92

Valves
and Springs ... D-90

Water
Outlet Fitting D-104
Water
Pump D-103

ENGINE INSTALLATION.
............D-105

FINAL IN-VEHICLE
ADJUSTMENTS.
.D-106
Check
Valve Timing . . D-109
Crankcase
Ventilation Valve. D-l 10

Oil
Filter
, . .
...D-lll

Valve
Adjustment D-107

Valve
Adjustment Procedure D-l08

SERVICE
DIAGNOSIS
D-112

SPECIFICATIONS D-l
13 37

Page 38 of 376

JEEP CJ 1953 User Guide
HURRICANE
F4
ENGINE

D-1.
GENERAL

This
section describes service and repair of the
F4
engine. The
engine
code
number shown in Fig.
A-3
is provided to identify the four cylinder engine

HURRICANE
F4
ENGINE

D-1.
GENERAL

This
section describes service and repair of the
F4
engine. The
engine
code
number shown in Fig.
A-3
is provided to identify the four cylinder engine.
The
meaning of the coded letters and numbers that

are
stamped on the water pump boss, at the front of the cylinder block, is given below.
Letter
to
Designate
Market

M
—
Military
E
—
Export

D
— Domestic
I
—
Industrial
&
Marine

Letter
to
Designate
Engine
Letter
to
Designate
Year
Built
R
— 1969

S
— 1970

T
— 1971
U—
1972

V
— 1973

W
— 1974

Numbers
to Designate
Compression
Ratio

F
— F4-134
Engine
63
67
•

71
-
6.3 to 1

•
6.7 to 1

-
7.1 to 1

Market
-
D
S F

(Domestic)

(1970)

Engine-
EXAMPLE

123 A B S
(F4-134)

Day- "L

Compression
Ratio

(6.7)
-
Service Engine (S)
Short
Block
(R)

-.010*
Oversize Pistons

(123rd)
-.010*
Undersize
Main

and
Rod Bearings
All
disassembly and assembly procedures are
presented in logical order, assuming a complete

engine
overhaul with
engine
removed from the vehicle. However, many of
these
procedures can
also be performed as on-vehicle services if vehicle
or
engine
components are removed to gain access
to parts involved.

Note:
Some
engines
are equipped with an exhaust
emission control system. Service information on
the components of this system is given in Section

F-l.
D-2.
Description

The
Hurricane
F4-134
engine
is an F-head, four-
cyiinder
engine
of combination valve-in-head and valve-in-block construction.
Large
intake valves
mounted in the head allow
rapid,
unobstructed
flow of fuel and air to the combustion chambers through short, water-jacketed intake passages.The
intake valves are operated by push rods through

rocker
arms. The exhaust valves are mounted

in
the block with through water jacketing to provide
effective
cooling. The exhaust valves are
operated by conventional valve tappets.
The
engine
is pressure lubricated. An oil pump

driven
from the camshaft forces the lubricant
through oil channels and drilled passages in the

crankshaft
to efficiently lubricate the main and
connecting rod bearings.
Lubricant
is also force
fed to the camshaft bearings, rocker arms, timing
gears, etc.
Cylinder
walls and piston pins are

lubricated
from spurt
holes
in the "follow" side of
the connecting rods.
Circulation
of the coolant is controlled by a
thermostat in the water
outlet
elbow cast as part
of the cylinder head.

The
cylinder head assembly when installed on the

engine
consists of the inlet valve guides, inlet valves, inlet valve springs, rocker arm and shaft assemblies, spark plugs, temperature indicator
fitting, water
outlet
fitting, and other assembled

parts.
The carburetor and air cleaner assembly
bolt to the top of the cylinder head. The rocker

arm
cover is attached to the top of the head to
enclose
the inlet valve mechanism.
The
engine
is equipped with a fully counterbalanced
crankshaft
supported by three main bearings. To better control balance, the counterweights are in
dependently forged and permanently attached to
the crankshaft with dowels and cap screws that are tack-welded.
Crankshaft
end play is adjusted by
shims placed
between
the crankshaft thrust washer

and
the shoulder on the crankshaft.
The
exhaust manifold is a separate unit. The intake
manifold is cast as an integral part of the cylinder
head and is completely water jacketed.
This
con
struction transfers heat from the cooling system
to the intake passages and assists in vaporizing
the fuel when the
engine
is cold. Therefore, there
is no heat control valve required in the exhaust manifold. Individual exhaust ports in the cylinder
block direct
gasses
into the exhaust manifold for unobstructed flow through the exhaust system.

The
pistons have an extra
groove
directly above
the top ring which acts as a heat dam or insulator.
As
is common practice with manufacturers,
some

engines
are built with oversize cylinder bores or undersize crankshaft journals. These
engines
are
considered standard as replacement parts of the

correct
sizes are supplied. Before ordering parts or
doing any work with a particular engine, it is important to check the
engine
code
number to
determine if oversize or undersize parts are re

quired.
Definite identification is given by a letter
stamped after the
engine
code
number. See Fig.

A-5
for location. The letters used and their mean ings are given here:

A
— .010*
[0,254
mm.] undersize main and
connecting rod bearings.

B
— .010"
[0,254
mm.] oversize pistons.

AB
—
Combination
of A and B.

S
—
Service
engine.

R
—
Short
Block.
Detailed specifications for the
Hurricane
F4
engine

are
at the end of this section.
Torque
specifications
for
engine
service are at the end of this manual in Section U. When adjustments are necessary, refer to
these
specifications so that factory clearances

are
maintained.

D-3.
Engine Mountings

The
front of the
engine
is supported by two rubber
Text continued on
page
41. 38

Page 39 of 376

JEEP CJ 1953 User Guide
Jeep
UNIVERSAL
SERIES
SERVICE
MANUAL

FIG.
D-l—HURRICANE
F4-ENGINE
— END
SECTION
VIEW

1— Intake Valve Spring Retainer

2—
Adjusting
Screw
3—
Nut

4— Rocker Arm
5—

Page 40 of 376

JEEP CJ 1953 User Guide
D
HURRICANE
F4
ENGINE ®
<S>® ® ® ®

®
® @> ® ® ®® ® (§) 11759

FIG.
D-2—HURRICANE F4-ENGINE
—
SIDE SECTIONAL VIEW

1— Fan
2— Water Pump
3— Pipe Plug
4— Water O

Page 41 of 376

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL

D
insulator
mountings attached to the frame side

rail
brackets. The
rear
of the engine-transmission
assembly is supported by a rubber insulator
mounting under the
rear
of the transmission on
the frame center cross member.
This
cross member
is bolted to the frame side
rails
so that it can be
dropped when removing the transmission or engine-

transmission
assembly. The rubber insulators allow
free side and vertical oscillation to effectively

neutralize
engine
vibration at the source.

The
rubber
insulator mountings should be inspected
for separation and deterioration by jacking the
power plant away from the frame, near the sup
ports. Vibration cannot be effectively absorbed by
separated or worn insulators. They should be re placed if faulty.

D-4.
Engine
Ground
Strap

To
be sure of an
effective
ground for the electrical

circuits,
a ground strap bridges the right front

engine
support to the chassis. The connections of this strap must be kept clean and tight for proper
operation of the electrical system.

D-5. ENGINE REMOVAL

Should
the
engine
require overhauling, it is neces

sary
to remove it from the vehicle. The following procedure covers removal of the
engine
only.

The
engine, transmission and transfer case may be
removed as a unit by removing (in addition to the following procedure) the radiator guard and the
access plates in the floor pan.

a.
Drain
the cooling system by opening the
drain
cocks at the
bottom
of the radiator and lower right
side of the cylinder block.

b.
Disconnect the battery at the positive terminal
to avoid the possibility of short
circuit.

c. Remove the air cleaner horn from the carburetor
and
disconnect the breather
hose
at the oil filler
pipe.

d.
Disconnect the carburetor choke and throttle controls by loosening the clamp
bolts
and set
screws.

e. Disconnect the fuel-tank-to-fuel-pump line at the fuel pump by unscrewing the connecting nut.
f- Plug the fuel line to prevent fuel leakage.
g. Remove the radiator and radiator grille support

rods.

h. Remove the upper and lower radiator
hoses
by
loosening the
hose
clamps and slipping the clamps
back
on the
hose.
If so equipped, remove the heater

hoses
(one to the water pump, one to the
rear
of
the cylinder head) in the same manner.

i.
Remove the four
bolts
from the fan hub and re

move
the fan hub and fan blades.

j.
Remove the four radiator attaching screws. Re
move
the radiator and shroud as one unit, k. Remove the starting motor cables. Remove the

starting
motor.

I.
Disconnect the wires from the alternator or
generator. Disconnect the ignition
primary
wire
at the ignition coil.
NOTE:
ON
ENGINES EQUIPPED WITH EX

HAUST
EMISSION CONTROL, REMOVE THE
AIR
PUMP,
AIR
DISTRIBUTION
MANI
FOLD,
AND
ANTI-BACKFIRE (DIVERTER)

VALVE.
SEE SECTION
Fl
FOR PROCEDURE.
m.
Disconnect the oil pressure and temperature
sending unit wires at the units.

n.
Disconnect the exhaust pipe at the exhaust
manifold by removing the stud nuts.

o.
Disconnect the
spark
plug cables at the plugs

and
remove the cable bracket from the rocker arm cover stud.

p.
Remove the rocker arm cover by removing the
attaching stud nuts.

q.
Attach a lifting bracket to the
engine
using
existing head bolt locations. Be sure the
bolts
selected
will
hold the
engine
with the weight

balanced.
Attach lifting bracket to a boom hoist,

or
other lifting device, and take up all slack,
r.
Remove the two nuts and
bolts
from each front

engine
support. Disconnect the
engine
ground strap.
Remove the
engine
supports.
Lower
the
engine
slightly to permit access to the two top
bolts
on
the flywheel housing.
s. Remove the
bolts
which attach the flywheel
housing to the engine.

t.
Pull
the
engine
forward, or
roll
the vehicle back

wards,
until the clutch clears the flywheel housing.

Lift
the
engine
from the vehicle.

D-6. ENGINE DISASSEMBLY

Engine
disassembly is presented in the sequence to be followed when the
engine
is to be completely
overhauled after removal from the vehicle. Some
of the operations of the procedure are also ap
plicable
separately with the
engine
in the vehicle,

provided
that wherever necessary the part of the

engine
to be worked on is first made accessible by
removal
of
engine
accessories or other parts.

When
the disassembly operations are performed

with
the
engine
out of the vehicle, it is assumed,
in
this procedure, that all of the accessories have been removed
prior
to starting the disassembly

and
the oil has been drained.
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle,

special
instructions are given to cover different
operations required when disassembly is
done
with the
engine
installed.

During
disassembly operations, the
engine
should
be mounted in a suitable
engine
repair
stand. Where

practicable,
modify or adapt an existing repair

stand
as necessary to accommodate the engine. If

an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that

will
protect personnel against an accident and the
engine
and its parts against damage.

NOTE:
If the
engine
is being disassembled because
of possible valve failure, check the valve tappet
clearance
before disassembly. Improper valve

clearance
could be the possible cause of valve

failure,
indicating a need for more frequent valve
checks and adjustments. 41

Page 42 of 376

D

HURRICANE
F4
ENGINE
D-7.
Remove Water Pump
Remove the
bolts
and lockwashers that attach the
water pump to the cylinder block. Remove the water pump.

D-8.
Remove
Exhaust
Manifold
Remove the five nuts from the manifold studs.

Pull
the manifold off the mounting studs. Remove the center and two end gaskets from the cylinder
block. See Section Fl for exhaust emission con trolled engines.

D-9.
Remove Oil
Filler
Tube

Loop
a piece of wire several times around the tube
below the top and make a
loop
through which a
pry
bar may be used to pry over the top of the

engine
water
outlet
fitting.
Pull
on the tube, tapping it just above where it enters the crankcase.

D-10.
Remove Water Outlet Fitting
Remove the nuts and lockwashers that attach the
water
outlet
fitting to the cylinder head.
Lift
the
outlet
fitting from the cylinder head.

D-11.
Remove Thermostat

With
the water
outlet
fitting removed, the thermo
stat can be lifted from the water
outlet
elbow on the cylinder head.

D-12.
Remove
Crankshaft
Pulley
Remove the crankshaft nut.
Install
a puller and
pull

the pulley from the crankshaft.

D-13.
Remove Distributor

a.
Remove
spark
plug cables from the distributor
cap,
noting the order in which they are assembled to ensure correct reassembly. No. 1
spark
plug

terminal
is in the 5 o'clock position. Starting with this tower the cables are installed in a counterclockwise direction in
1-3-4-2
firing order.

b.
Remove the
primary
lead from the terminal

post
at the side of the distributor.
c. Remove the screw holding the distributor to the crankcase and lift the assembly from the engine.
D-14. Remove Oil Pump

The
oil pump is located externally on the left side
of the engine. If only the oil pump is being removed

with
the
engine
in the vehicle, set No. 1 piston at
TDC
for reference for reinstalling the oil pump
without greatly disturbing the ignition timing.
First
remove the distributor cover and
note
the
position of the distributor rotor.
If
the distributor is already removed, sight through
the distributor
hole
before removing the oil pump.
The
slot should be near vertical. Remove the capscrews and lockwashers attaching the oil pump
to the cylinder block.
Carefully
slide the oil pump

and
its drive shaft out of the cylinder block.

D-1S.
Remove
Crankcase
Ventilation Valve

To
remove the crankcase ventilation valve from
the elbow fitting screwed into the inlet manifold of the cylinder head, first remove the
hose
and
clamp from the valve (Fig. D-32), then using a
wrench
carefully unscrew the valve from the
elbow.

D-l6.
Remove Rooker Arm Assemblies

The
rocker arm cover was previously removed as

a
step
of the
engine
removal (Par. D-5).
Remove the nuts from the rocker arm shaft support
studs, and lift the rocker arm assembly off the studs.
Lift
the intake valve push rods out of the
cylinder
block.

D-17.
Remove
Cylinder
Head

a.
Removal.
Disconnect the oil line from the flared tube con
nector and remove the rocker arm attaching stud nuts, and rocker arm shaft assembly if not pre
viously removed. Two end head
bolts
cannot be removed until the rocker arm shaft is removed.
Remove the cylinder head bolts.
There
is one
cylinder
head bolt located below the carburetor
mounting, inside the intake manifold, that must
not be overlooked.

Carefully
lift the cylinder head off the block.
Remove the valve push rods and the valve lifters.
FIG.
D-3—REMOVING
RIDGE
WITH
REAMER

Remove and discard the cylinder head gasket,
b. Disassembly.
Disassemble the parts of the cylinder head as
follows:
With
a spring compressor tool remove the
two-piece
locks recessed in the valve spring re

tainers.
Pull
the
O-ring,
valve spring, and valve out
of the cylinder head. Identify the valves for return to the same
guides
from which they are removed.
42

Page 43 of 376

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

FIG.
D-4—F4-134
ENGINE

1— Dowel Bolt
2— Bolt
3— Flywheel Ring Gear
4— Flywheel 5—
Clutch
Pilot Bushing
6— Lockwasher
7— Nut
8— Flywheel Housing
9—
Cable

10— Engine Plate (Rear)
11— Woodruff Key
12— Camshaft Thrust Plate
13— Spacer
14— Camshaft Gear
15— Washer
16—
Crankshaft
Shim (.002 *)
17—
Crankshaft
Thrust Washer
18—
Crankshaft
Gear
19— Spacer
20—
Oil
Slinger
21—
Crankshaft
Oil Seal
22— Packing Ring
23—
Gear
Cover Gasket
24—
Gear
Cover
25—Pulley

26—
Crankshaft
Pulley Nut
27—
Timing
Indicator
28— Engine Support Front Insulator
29—
Front
Engine Plate
30— Bolt 31—
Front
Plate Gasket 14251
43

Page 44 of 376

D
HURRICANE
F4
ENGINE
Note:
Check
the condition of the rubber O-rings.
Defective O-rings could be the major cause of oil
leakage into cylinders. Always discard and replace

all
O-rings removed as only new O-rings should be installed at reassembly.

D-18.
Ream
Cylinder
Bore Ridges

To
prevent breaking the piston lands, the ridge
at the top of each cylinder bore must be removed

first.
To remove this ridge, use a cylinder ridge
reamer,
as shown in Fig. D-3 following the instruc
tions furnished by the reamer manufacturer. Use

care
not to cut below the top of the upper ring
travel
in the bore. Keep each piston top covered

with
an oil-soaked cloth to prevent cuttings from
falling
into the cylinder.

Note:
This
operation should be performed at this
time before the
engine
is rotated for the sequence

steps
following.

D-19.
Remove Oil Pan
Rotate the
engine
to the upside down position.
Remove the screws and lockwashers that attach
the oil pan to the cylinder block. Remove the oil

pan
and gasket.
Discard
the gasket.

D-20.
Remove Piston and Connecting
Rod
Assemblies
Remove the stamped locking nuts from the lower
end of each connecting rod bearing bolt. Remove
the connecting rod nuts. Remove the bearing cap evenly. Push the connecting rod and piston as
sembly out of the cylinder block with the handle end of a hammer until the piston rings are free from
the cylinder bore. Remove the piston and connecting rod assembly

from
the top of the cylinder block. Reassemble the
connecting rod bearing cap with the bearings in
place in the rod from which it was removed. Rotate
the crankshaft and follow the same procedure until
all
the piston and connecting rod assemblies are
removed.
Pistons and connecting rod assemblies may be removed for repair with the
engine
in the vehicle after draining the cooling system, removing the

oil
pan and the cylinder head, and reaming the ridges as previously described.

D-21.
Remove
Timing
Gear
Cover

Remove the bolts, nuts, and lockwashers, that at
tach
the timing gear cover to the engine. Remove
the cover, timing pointer, and cover gasket.
Dis
card
the gasket. Remove the crankshaft oil seal

from
the timing gear cover and discard the seal. Remove the oil slinger and spacer from the
crank

shaft.

D-22.
Remove
Timing
Gears

Use puller W-172 for pulling both the crankshaft
and
the camshaft gears.
With
the threaded cap-
screws supplied, adapt the puller to the crankshaft
FIG.
D-5—PULLING TIMING GEARS

1—
Puller
W-172 2—
Camshaft
Gear
gear and
pull
the gear.
With
the special hook-type

puller
bolts
that fit behind the camshaft gear
flange,
pull
the camshaft gear. Remove the Wood

ruff
Keys.

D-23.
Remove
Front
End Plate
Remove the screws and lockwashers that attach the
front end plate to the cylinder block. Remove the
front end plate and gasket.
Discard
the gasket.
D-24. Remove
Clutch

Remove four
bolts
and lockwashers diagonally

opposite
that attach the clutch assembly to the
flywheel, leaving two
opposed
bolts
to be
loosened
alternately until the clutch spring pressure is re
lieved.
Then,
support the clutch assembly with
one hand while removing the two remaining bolts.

For
information on disassembly, inspection, repair

and
assembly of the clutch refer to Section I. In
structions for removing the clutch when the
engine
is in the vehicle are also given in Section I.

D-25.
Remove Flywheel

The
flywheel is attached to the crankshaft with two tapered dowel
bolts
and four special bolts.
Remove
these
attaching parts. Use a pry bar be tween the flywheel and the back of the
engine
and
carefully
loosen
the flywheel from the crankshaft.

If
the flywheel is to be removed with the
engine

in
the vehicle, the transmission and clutch must
first be removed as detailed in Section I.

D-26.
Remove
Crankshaft

Slide
the crankshaft thrust washer and all end-play

adjusting
shims off the front end of the crankshaft.

Pull
the two pieces of
rear
main bearing cap packing out of position
between
the side of the bearing cap

and
the cylinder block.

Note
the marks on the bearing caps and cylinder
block for bearing number and position. 44

Load next 10 pages

Page: < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 220 next >
Search: (bolt pattern, gas type, roof rack, fuel fill door release, steering wheel, light)

Page 33 of 376

Page 35 of 376

Page 37 of 376

Page 38 of 376

Page 39 of 376

Page 40 of 376

Page 41 of 376

Page 42 of 376

Page 43 of 376

Page 44 of 376

JEEP Owners Manuals