door lock JEEP CJ 1953 Service Manual

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL
H
FIG.
H-59—HEAD LAMP

1—
Door

2—
Retaining
Screw

3—
Retaining
Ring

4—
Sealed
Beam
Unit
5—
Mounting
Ring

6—
Adjusting
Screw 7—
Housing

8—
Wires

9—
Door
Screw 310669
to cross the vertical
tapes
at the measured height
of each lamp center respectively.

g.
Remove the head lamp doors.
h.
Clean
the head lamps.

H-132.
Aiming Head Lamps

a.
Turn
the headlights on low beam. Cover the lamp not being aimed. Be sure to use the horizontal reference line on the screen that is the same dimen­
sion as the vehicle lamp height.
b.
Turn
the vertical aiming screw counterclock­
wise until the lamp beam is considerably lower

than
the horizontal reference line on the screen.
Then,
turn
the screw clockwise until the top
edge

of the high intensity
area
is even with the horizontal

line.
See Fig. H-60.
I
(T)

JT)

1'.'' | '':'
11460

FIG.
H-60—HEADLIGHT AIMING
CHART
1—
Vertical
Tape,
Left
Lamp
Center

2—
Vehicle
Centerline

3—
—Vertical
Tape,
Right
Lamp
Center
4—
Zone
of Greatest Intensity
5—
2
*
(Two Inches)
6— 25'0
'
7—
2
*
(Two Inches)
8—
Height
of
Lamp
Centers
9—
Horizontal
Tape

Note:
Always bring the beam into final position
by turning both aiming screws clockwise so that
the unit is held under proper tension when the operation is complete.

c. Turn
the horizontal aiming screw counterclock­
wise until the beam is off.
Then,
turn
the same
screw
clockwise until the
left
edge
of the high
intensity area is 2" [5,08 cm.] to the right of the
lamp center line. See Fig. H-60.

d.
Cover the lamp that has been aimed and aim
the other lamp using the same procedure.
e.
Carefully
reinstall the head lamp doors.

H-133.
Parking
and
Turn Signal Light
The
parking lights are mounted in the radiator

guard
panel just below the headlights. These lights

are
on only when the main switch control knob is
pulled
out to the first notch.

To
replace a parking lamp, remove two screws allowing the lens and colored reflector to be re­
moved. Replace the lamp, which is recessed back

in
the housing.

If
the
complete
parking light assembly is to be
removed for service or replacement, disconnect the

wire
plug at the back of the housing.
Then
remove
the nuts and lock washers securing the parking light assembly and remove out the front of the

panel.

H-134. Tail, Stop
and
Turn Signal Light

Refer
to Fig. H-57 and H-58.

The
tail
lights are mounted in the
rear
corner
posts

of the body. They are on whenever the main switch
control
knob is pulled out to any position.

a.
To replace a lamp, remove the snap ring on

early
models
and remove the lens; on late
models
remove lens screws, lens and gasket.
Clean
lens
and
reflector before replacing.
b. To remove the parking and
tail
light housing,
disconnect wiring, remove the two nuts and lock
washers securing
tail
light assembly to body and remove from
rear
of body.

H-135-
Backup Lights •
Refer to Fig. H-61.

The
backup lights on late production vehicles are located on the
rear
of the vehicle directly below
the
tail
light. The backup lights are actuated
through a switch when the ignition is on and the

transmission
is in reverse. 215