water pump JEEP DJ 1953 Owner's Guide

E

FUEL
SYSTEM
Note:
Do not remove pressed-in parts such as
nozzle, pump jet, or antipercolator air bleed.

j.
Remove body flange attaching screws, body flange assembly, and gasket.

k.
Remove idle-adjustment screw, spring, idle

port
rivet, throttle lever assembly, washer, fast
idle arm, throttle plate screws, throttle plate, and throttle shaft.
1. Remove throttle shaft seal by prying out seal

retainer.

Note:
Do not remove pressed-in vacuum passage

orifice.

m.
Remove choke valve screws and choke valve.

Unhook
choke spring and slide shaft from housing,
n.
Wash all parts in carburetor cleaning solution

and
blow out passages with compressed air. Do not immerse diaphragm or seals in cleaning solution.

Inspect
all parts for wear or damage. Always use
new gaskets when reassembling.

E-22.
Carburetor
Reassembly

•
Refer to Fig. E-13.

To
expedite
reassembly, it is advisable to group all

related
parts by the circuit to which they belong.

a.
Install
throttle shaft seal and retainer in flange casting.

b.
Install
fast-idle
arm,
washer, and lever assembly
on throttle shaft. Slide shaft into place and install throttle valve.

c.
Install
idle port rivet plug and idle adjusting

screw
and spring.

d.
Attach flange assembly to body casting. Use new gasket.
e.
Install
low-speed jet assembly.
f.
Early
production models install pump intake
strainer
in pump diaphragm housing and carefully
press into recess.

Note:
If strainer is even slightly damaged, a new
one must be installed.
g.
Install
pump diaphragm assembly in diaphragm housing.
Then,
install pump diaphragm spring
(lower)
and retainer.

h.
Install
pump lifter
link,
metering rod
arm,
upper
pump spring, and retainer.

I.
Install
metering rod jet.

Note:
No gasket is used with this jet.

j.
Install
diaphragm housing attaching screws in
the diaphragm housing, making sure that the

edges
of the diaphragm are not wrinkled.
Lower

into place and tighten screws evenly and securely,
k.
Install
throttle shaft seal, dust seal washer, and
shaft seal spring.

I.
Install
pump connector
link
in the throttle arm
assembly.
Install
throttle shaft arm assembly on
throttle shaft guiding connector
link
in pump lifter

link
hole.
CAUTION:
Linkage
must not bind in any throttle
position. If binding occurs,
loosen
clamp screw in
throttle arm, adjust slightly, then retighten screw.

m.
Install
pump check disc, disc retainer, and lock

ring.

n.
Install
metering rod and pin spring. Connect
metering rod spring.
o.
Check
and if necessary correct meter ing rod adjustment. Follow procedure of
Par.
E-16.
p.
Install
needle
seat and gasket assembly, needle,
float
and
float pin. The
stop
shoulder on the float
pin
must be on the side away from the bore of
the carburetor.

q.
Set float level to specifications. Follow pro­ cedure of
Par.
E-12.

r.
Install
air horn gasket and air horn assembly.

Install
attaching screws, lock washers, and choke
tube clamp assembly. Tighten center screws first,
s. Slide choke shaft and lever assembly into place
and
connect choke lever
spring.
Install
choke valve.
Center
the valve by tapping lightly, then hold in
place with fingers when tightening screws,
t.
Install
fast-idle connector rod with
offset
portion
of rod on top and pin spring on outside.
Install
fast-idle connecting rod spring.

E-23.
Correcting Acceleration
Flat
Spot

Early
production
Carburetor
Models 938-S, 938-
SA,
938-SC

Inasmuch
as a flat
spot
on acceleration or low speed
stumble can
come
from causes other than
car­

buretor
malfunction, it is recommended that
engine

tuning be thoroughly checked before attempting
any
actual carburetor work. Make sure that
ignition, compression, and timing are correct and
that fuel pump is supplying enough gas. Also, the F-head
engine
employs a water-heated intake

manifold.
Proper vaporization of the fuel depends
on correct intake manifold temperature. Since this
temperature is controlled by the cooling system
thermostat, include an operational check of the
thermostat when diagnosing the stumble. Operating
temperatures consistently below
155°F.
can cause stumble.

If
the stumble persists, a
YF-938-S,
YF-938-SA,

or
YF-938-SC
carburetor can be converted to a
YF-938-SD
carburetor by installing Special Kit
924161, consisting of a pump discharge check
needle, a metering rod, and a metering rod jet. If this kit is installed, the pump discharge check

needle
replaces the original
ball,
weight, and re­

tainer
and the small wire-type retainer used with
the
ball
check assembly must not be reinstalled.

When
installing the kit, check the size of the pump discharge jet, No. 2, Fig. E-14.
Early
production
YF-938S
and
YF-938SA
carburetors have a .025" [0,635 mm.] jet installed. If the carburetor being
converted has a .025" jet it must be opened up to .031" [0,787 mm.] by running a No. 68
drill
through
the jet as shown in
Fig.
E-14.
The jet must be drilled
as it is a pressed in part and cannot be replaced.
Upon
completing the installation of the conversion

kit,
mark
or tag the carburetor to indicate that it
is a
YF-938SD.
118

E

FUEL
SYSTEM
port into the venturi.

The
check
ball
in the pump plunger head is a vapor
vent for the pump well. Without this vent, vapor
pressure in the pump would force fuel from the
pump system into the
engine
manifold, causing

hard
starting when the
engine
is hot.
There
is another
hole
in the pump lever, into which
the accelerator pump rod can be inserted to pro­ vide quicker pump action.
This
adjustment setting
is used only in extreme cold temperature condi­ tions. The pump discharge check
ball
in the dis­
charge passage prevents discharge of fuel from the
pump nozzles when the accelerator pump is in­
operative.

E-31.
Choke System

The
choke system consists of a manually-operated
choke valve, a fast-idle connecting rod, and a fast-
idle arm. The choke valve is offset-spring loaded
to prevent over-choking during the starting
warm-
up period. When the choke valve is moved to a
closed position for starting, the fast idle connector

rod
revolves the fast idle
link.
This
action increases
the
engine
idle speed to prevent stalling during the

warm-up
period. A fast-idle connector rod return
spring
prevents
partial
closing of the choke valve.

E-32.
Carburetor
Removal

a.
Remove attaching wing nut and air cleaner from
carburetor.

b. Remove throttle cable from
ball
stud on throttle
lever adapter.

c.
Disconnect fuel line from carburetor inlet fitting.

d.
Disconnect positive crankcase ventilator
hose
from
nipple on carburetor body.
e. Disconnect distributor vacuum line from throttle body of carburetor.
f. Remove four attaching cap screws, carburetor,
and
gasket from intake manifold.

E-33.
Air
Horn
Body Removal and Disassembly

a.
Remove attaching screws, and carefully lift air
horn
body upward to remove from fuel bowl body.
b. Place air horn body in inverted position on
bench. Remove float hinge pin and lift float as­ sembly from cover. Remove inlet valve
needle
from
float arm. Remove
needle
seat, fiber gasket

and
seat screen from air horn body; discard gasket. See Fig. E-22.

c.
Depress shaft and allow spring to snap re­ peatedly to remove power piston from air horn body.
This
will
force power piston retaining washer

from
air horn body.

d.
Remove retainer from end of accelerator pump
plunger shaft. Remove pump assembly from pump

inner
arm. Loosen set screw on inner arm and re­

move
outer lever and shaft from plunger. Remove gasket from air horn body or fuel bowl body and

discard.

e. Remove two retaining screws and choke valve plate from choke shaft. Withdraw choke shaft from
air
horn body. Remove choke lever and collar from
choke shaft.
Note
position of choke lever in relation
12856
FIG.
E-22—AIR HORN BODY

1
—
Float

2— Power Piston
3—
Pump
Plunger
4—
Choke
Valve to choke trip lever at end of the choke shaft for

ease
in reassembly.

E-34.
Fuel
Bowl Body Disassembly

a.
Remove return spring of pump plunger and pump well from fuel bowl body. Remove small

aluminum
check
ball
from
bottom
of pump well
by inverting fuel bowl body and shaking into hand. Remove pump inlet screen from
bottom
of fuel bowl.
b. Remove main metering jets from fuel bowl body
using Tool C-3748.

c.
Remove power valve and fiber gasket from fuel bowl body; discard gasket.

d.
Remove three attaching screws, venturi cluster
assembly, and gasket from fuel bowl body. Center
screw has smooth shank and fiber gasket for the accelerator pump fuel bypass and seal.
e. Using a
pair
of long nosed pliers, remove T-
shaped retainer, accelerator pump discharge spring

and
steel discharge
ball
from fuel bowl body.
f. Remove two inserts from main well.

E-35.
Throttle Body Removal and Disassembly

a.
Invert
fuel bowl body; remove three attaching
screws,
throttle body and gasket; discard gasket.
b. Remove idle mixture adjustment
needles
and
springs from throttle body.

Note:
No further disassembly of the throttle body
is required. The throttle valves should never be
removed, as the idle and
spark
holes
are drilled in
direct
relation to the location of the throttle valves

and
shaft. Removal of the throttle valves
will
upset
this alignment. The throttle body assembly is serv­ iced only as a complete assembly with throttle valves intact.

E-36.
Carburetor
Cleaning and Inspection
Dirt,
gum, water, or carbon contamination on the 122

FUEL
SYSTEM
|
11893

FIG.
E-29—FUEL
AND
VACUUM
PUMP—F4
ENGINE,
EARLY
MODELS

1—
Cover
Screw
2—
Lockwasher

3—
Diaphragm
Spring
4—
Spring
Seat 5—
Diaphragm
and Rod
6—
Oil
Seal 7—
Valve
Assembly
8— Body
9—
Rocker
Arm Pin Spring
10—
Fuel
Diaphragm
11—
Oil
Seal Retainer
12—
Diaphragm
and Rod 13—
Valve
Retainer
14—
Cover
15—
Gasket

16—
Screen

17—
Bow!

18—
Bail
19—
Gasket

20—
Screw
21—
Rocker
Arm Spring
22—
Link
Spacer
23—
Rocker
Arm

24—
Washer

25—
Body
fuel. The diaphragm can start and
stop
many
times
in
each mile of vehicle operation, but the pump
actuating lihkage is always in operation while the

engine
is running. The fuel pump incorporates a
pulsator and pulsator chamber to dampen the
effect

of pump pressure pulsations on the carburetor

needle
valve.
This
prevents high fuel level in the

reservoir
that would result from the
needle
being

jarred
away from its seat. Also, operating
economy
would be affected because a high fuel level usually results in an over-rich mixture.

The
actuating linkage has its own spring to ensure
continuous contact of the lever to the camshaft
eccentric.

This
fuel pump has a sediment bowl and filtering
screen which is attached to the top of the pump by
a
wire clamp and thumb nut. The screen and sedi­
ment bowl should be cleaned at least twice yearly
to prevent trouble due to a blocked screen or water
freezing. The bowl should be washed and wiped

dry
and the screen dried and then cleaned with a
stiff
brush.
When reassembling the bowl make cer­
tain
that the cork gasket is not broken; reverse it
and
position it flat on the seat, then install the
bowl and tighten the thumb nut securely. After
cleaning, start the
engine
and carefully inspect the
bowl for leakage.

E-46.
Disassembly
Remove the cover plate, gasket, and screen or
bowl clamp, sediment bowl, gasket and screen if so equipped.
Mark
the two castings with a file to
ensure positioning in the same relation upon
assembly. Remove the screws attaching the fuel cover to the pump body. Remove the cover,

diaphragm,
and spring. Remove rocker arm pin,
rocker
arm, and rocker arm spring. Remove the
valve plate screw and separate the valve plate

retainer,
valve gaskets, and valves.

Clean
all parts in cleaning solvent and blow out

with
compressed air. Valves should not be removed

from
the valve housing assembly.
Check
all parts
to see that
they
have not
been
cracked or broken
and
that screw threads have not
been
stripped or
cross threaded. Refer to Par. E-49 for fuel pump
testing. 126

E

FUEL
SYSTEM
E-78. SERVICE DIHGNOSIS
Symptoms Probable Remedy

Excessive
Fuel
Consumption:
Tires
improperly inflated Inflate

Brakes
drag Adjust
Engine
operates too cold Check thermostat
Heat control valve inoperative Check thermostatic spring
Leak
in fuel line Check all connections

Carburetor
float level high. See
"Carburetor"
section
Accelerator pump not properly adjusted Adjust

Leaky
fuel pump diaphragm Replace
Loose
engine
mountings causing high carburetor fuel level Tighten Ignition timing slow or spark advance stuck See "Distributor" section

Low
compression. Check valve tappet clearance
Air
cleaner dirty
.
Remove and clean

Engine
Hesitates on Acceleration: Accelerator pump
does
not function perfectly.
...................
.Replace piston and rod or adjust
Carburetor
float level. ... .Adjust

Spark
plugs Replace or clean and adjust

Low
compression Check valves

Distributor
points—dirty or pitted Replace

Weak
condenser or coil Replace

Carburetor
jets restricted Remove and clean

Excessive
engine
heat See "Engine" section

Engine
Stalls—Won't Idle:
Improper
condition of carburetor See
"Carburetor"
section

Low
speed
jet restricted Remove and clean
Dirty
fuel sediment bowl screen Remove and clean

Air
cleaner dirty Remove and clean

Leaky
manifold or gasket Replace

Fuel
pump diaphragm porous. Replace
Loose carburetor. Tighten
flange
nuts

Water
in fuel
Drain
and clean system

Improper
ignition. .See "Distributor" section

Spark
plugs Clean and adjust

Valves
sticking.
Grind
valves 134

Fl

EXHAUST
EMISSION CONTROL SYSTEMS The
air distribution manifold should be installed
after the exhaust manifold assembly is torqued
to the cylinder head. The recommended procedure
for exhaust manifold assembly installation is as follows:
Clean
the mating surface of both the
manifold and cylinder head.
Install
the exhaust manifold to the cylinder head using a new gasket.

Tighten
the manifold to cylinder head, attaching
bolts
down evenly.
Finish
torque tightening to 29
to 35 ft. lbs. [3,4 a 4,8 kg-m.].

Fl-23.
REQUIRED
EQUIPMENT

Each
station licensed to perform repair and main­
tenance on the Exhaust Emission Control System
must be equipped with that equipment necessary
for major
engine
tune-up analysis which shall in­ clude at least the following or equivalent.
Ignition Analyzer Oscilloscope
Ammeter
Ohmmeter
Voltmeter Tachometer
2 Vacuum Gages

Pressure
Gage (0-10 psi.)

Cam
Angle Dwell Meter Ignition Timing
Light

Engine
Exhaust Combustion Analyzer Compression Tester

Fl-24.
REPLACEMENT
PARTS

Parts
necessary to repair and/or maintain the

Exhaust
Emission Control System are available through any Jeep
SALES CORPORATION
ware­
house.

Fl-25.
WARRANTY

All
parts of the Exhaust Emission Control System

are
covered by the Manufacturer's Warranty as stated in the Warranty Service and 'Jeep' Quality
Maintenance Plan booklet.

Fl-26.
EXHAUST EMISSION CONTROL
SYSTEM
DIAGNOSIS GUIDE
Pump Noisy

Hoses Touching Other Parts of Engine or Body (Hood).

Note:
The air pump is not completely noiseless.

Under
normal conditions, pump
noise
rises in pitch as
engine
speed
increases. It is also desirable to
allow for normal break-in wear of the pump prior
to replacement for excessive noise.

Pump Seized

Replace
pump.

Leak
In
Hose

Check
for leaks; using
soap
and water — tighten
clamps or replace
hoses.
Pump
Inoperative

Loose Belt — tighten belt — do not pry on housing.

Filter
Plugged — replace.

Exhaust Backfire

Check
for vacuum leaks — correct as necessary.
Check
air filter for excessive
restriction
— replace as necessary.

Check
anti-backfire valve — replace as necessary.

Induction System Backfire

Verify
engine
timing and distributor dwell.

Verify
accelerator pump charge. 146

F2
EXHAUST EMISSION CONTROL SYSTEMS
F2-3L
EXHAUST EMISSION CONTROL SYSTEM
DIAGNOSIS
GUIDE

Pump Noisy
Hoses Touching Other Parts of Engine or Body (Hood).

Note:
The Air Pump is not completely noiseless.

Under
normal conditions, pump
noise
rises in pitch as
engine
speed
increases. It is desirable to allow
for normal break-in wear of the pump prior to re­
placement for
excessive
noise.
Pump Seized
Replace pump.
-
do not pry on housing.
Leak
In Hose

Check
for leaks; using
soap
and water, tighten clamps or replace
hoses.

Pump Inoperative
Loose Belt — tighten belt
-

Filter
Plugged — replace.

Exhaust
Backfire

Check
for vacuum leaks — correct as necessary.
Check
anti-backfire valve — replace as necessary
Induction System Backfire

Verify
engine
timing and distributor dwell.
Verify
accelerator pump charge.

F2-32.
EXHAUST EMISSION CONTROL SYSTEM MAINTENANCE CHART

Efficient
performance of the Exhaust Emission very important that all of the maintenance require-

Control
System is
dependent
upon precise main-
ments
are performed with extreme care at the
tenance. As indicated in the following chart, it is specific interval indicated.
Thousands of miles* or

OPERATION
number of months whichever occurs first 2 6 12 18 24 30
Inspect engine-driven
belts
for condition and tension R R
Replace positive crankcase ventilation valve
(PCV)
R R

Check
for free operation of exhaust manifold heat control valve O O O O O

Clean
carburetor air cleaner — Oil Bath O O O O O
Replace carburetor air cleaner
element
— Dry Type O
Check
heated air system O O

Engine
tune-up O O

Check
engine
timing R O O O
Adjust
carburetor idle
speed
and mixture R O O O

Perform
factory-recommended road
test
for evaluation of overall performance and handling O O O O O

R
— Required Services O — Recommended Services

*
Miles Kilometers
2,000
—
3,200

6,000
—
9,600

12,000
—
19,200 18,000
—
28,800
24,000
—
38,400
30,000
—
48,000

F2-33.
GENERAL SPECIFICATIONS
Air
Pump Belt Tension 60 lb.

Rotor
Ring Screw Torque . 37 lb-in.
Housing Cover Bolt Torque 10 lb-ft. Speed Ratio, Air Pump to Engine
1
\i to 1

F2-34.
EXHAUST EMISSION CONTROL SYSTEM CARBURETOR SPECIFICATIONS

Make
Rochester Model Designation 2G Code Number
7027082
—
7041185

Choke
Manual
Number of Barrels 2

Throttle
Bore... \W [3,65 cm.]
Main
Metering Jet Production .051" - 60° [1,29 mm.]
High
Altitude — over
5000
ft .049" - 60° [1,24 mm.]
—
over
10,000
ft .047" - 60° [1,19 mm.]

Float
Level
Adjustment* 1%," [2,94 cm.]
Float
Drop Adjustment l%" [4,76 cm.]
Pump Rod Adjustment** 1%" [2,94 cm.]
Engine
Idle
R.P.M.
(In Neutral) 650 to 700

Initial
Idle Speed-screw
setting
3 turns in

Initial
Idle Mixture-screw
setting
2 turns out
Dash
Pot Setting. Y%w [3,75 mm.]
*From
air horn gasket to top of float at toe.

**From
air cleaner ring to top of pump rod.
158

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

COOLING
SYSTEM

Contents

SUBJECT
PAR.

GENERAL
.G-l Antifreeze Solutions. .G-l6
Cylinder
Block.
..................
.G-8

Draining
Cooling System............... G-3

Engine
Overheating..
.................
.G-19
Fan
Belt.
......... .........
.G-18
Filling
Cooling System.................
G-2

Inhibited
Coolant Solution .G-l7

Temperature
Sending Unit.
...........
.G-l0

Thermostat
.........................
G-9

RADIATOR
.G-5
Radiator
and Heater Hoses.............
G-7
SUBJECT
PAR.

Radiator
Pressure
Cap.................
G-4

Radiator
Removal and Replacement..... G-6

WATER
PUMP.
. . .G-ll
Water
Pump Disassembly. .............G-13

Water
Pump Inspection.
..............
.G-12

Water
Pump Reassembly.
.............
.G-14

Water
Pump Removal and Replacement. .G-l5

SERVICE
DIAGNOSIS.
.G-20

SPECIFICATIONS
. .G-21

ANTIFREEZE
CHART.
..... ... .G-22

G-l. GENERAL
a.
The satisfactory performance of the Hurricane

F4
engine
is controlled to a great
extent
by the proper operation of the cooling system. The
engine

block is full length water jacketed which prevents
distortion of the cylinder walls. Directed cooling
and
large water holes, properly placed in the cylin­
der head gasket cause more water to flow past the
valve
seats
(which are the
hottest
parts of the

block)
and
carry
the heat away from the valves, giving positive cooling of valves and seats.

Minimum
temperature of the coolant is controlled by a thermostat mounted in the
outlet
passage of
the engine. When the coolant temperature is below
thermostat-rated temperature, the thermostat re­ mains closed and the coolant is directed through
the radiator-bypass
hose
to the water pump. When the thermostat opens, coolant flow is directed to
the top of the radiator. The radiator dissipates the
excess
engine
heat before the coolant is recirculated
through the engine.
The
cooling system is pressurized. Operating pres­
sure
is regulated by the rating of the radiator cap

which
contains a relief valve, b. The Dauntless V-6
engine
efficiency and per­formance is controlled to a great
extent
by proper
operation of the cooling system. The cooling system

does
more than cool the engine. It also directs
the flow of coolant to provide the
best
operating
temperature range for each part of the engine.

In
the Dauntless V-6
engine
coolant is forced by
the water pump into two main passages that run the length of the block on each side (Fig. G-l).
FIG.
G-1—COOLANT
FLOW
THROUGH
THE
DAUNTLESS
V-6
ENGINE

161

COOLING
SYSTEM

14263

FIG.
G-2—COOLING SYSTEM
COMPONENTS
V-6
ENGINE

1—
Radiator
Pressure Cap

2—
Hose
Clamp

3—
Radiator
Hose (Inlet-Upper)
4—
Radiator
Hose (Outlet-Lower) 5—
Bolt
6—
Water
Pump Assembly 7—
Cap
8—Thermostat
By-Pass Hose
g—Water Outlet
Elbow

10—
Gasket

11—
Thermostat
12—
Water
Pump Gasket

13—
Dowel
Pin
14—
Radiator
Shroud (Heavy Duty Cooling) 15—
Pulley

16—
Fan
Spacer
17—
Fan
and Alternator Belt

18—Fan

19—
Lockwasher

20—
Radiator

21—
Drain
Cock
From
these
main passages, the coolant flows around
the
full
length of each combustion chamber.

After
cooling the block, the coolant passes through
ports between the block and each cylinder head.
These
ports direct most of the coolant flow around the exhaust valve area to prevent hot exhaust
gases

from
overheating the exhaust ports.

From
the cylinder heads, the water passes into a
water
manifold between each of the heads and the

water
pump. If the thermostat is closed, the coolant
is ported back to the pump where it is recirculated

back
into the pump and into the engine. After the
coolant heats enough to open the thermostat, the coolant is directed from the water manifold through
a
hose
to the top of the radiator and then through
the radiator which acts as a heat exchanger to cool the fluid. The coolant is then ported through a
hose

from
the bottom of the radiator to the pump, which

recirculates
it back to the engine.

The
cooling system is pressurized. Operating pres­
sure
is regulated by a relief valve in the radiator

cap. The
heater inlet
hose
is connected to a port on
the right bank cylinder head. The outlet
hose
is connected to the heater adapter tube on the water

pump.

c.
It is recommended when using water for coolant
that the cooling system be flushed and checked for leaks twice a year, preferably in the
fall
before
antifreeze is added and in the spring when the antifreeze is drained.

Reverse
flushing
will
aid greatly in removing rust 162

G
COOLING SYSTEM and
the outlet
hose
is connected to the water pump
housing.
When
installing a new hose, clean the pipe connec­
tions and apply a thin layer of nonhardening seal­
ing compound. Hose clamps should be properly
located over the connections to provide secure fastening. The pressurized cooling system pressure

can
blow off improperly installed hoses.

G-8.
Cylinder
Block

Any
coolant leaks at the engine block water joints

are
aggravated by pump pressure in the water

jacket
and by pressure developed in the cooling system when the pressure cap is in place.
Small
leaks showing up only as moist
spots
often
cannot
be detected when the engine is hot except by the
appearance of rust, corrosion, and dye stains where
leakage evaporated. Also, expansion and contrac­ tion of the engine block resulting from extreme
temperature changes can aggravate leaks. For
these

reasons, when checking for coolant leaks inspect
the block when it is cold and while the engine is

running.
A
leaking
drain
cock or plug that cannot be stopped

leaking
by tightening should be replaced.
Leaking

core-hole expansion plugs should be replaced.
If
tightening gasketed joints
will
not correct leak­
age, install new gaskets. Use a sealing compound
where recommended.

G-9.
Thermostat
a.
The cooling system of the engine is designed
to provide adequate cooling under most adverse conditions. However, it is necessary to employ
some

device to provide quick warming and to prevent
overcooling during normal operation. Automatic
control
of engine operating temperature is provided
by a water flow control thermostat installed in the
water
outlet of the
Hurricane
F4 engine. The ther­
mostat is a heat-operated valve. It should always
be maintained in working order and the vehicle
should never be driven without one installed as there would then be no control of engine tempera­

ture.
The temperature at which the thermostat
opens
is preset and cannot be altered.

b.
The thermostat on the
Hurricane
F4 engine is
located in a housing on the top front of the cylinder

head.
On the Dauntless V-6 engine it is located
in
the thermostat housing of the air intake manifold.

The
standard engine thermostat for the
Hurricane

F4
and Dauntless V-6 engine has a normal rating
of
190°F.
[87.8°C]
and should begin to open at

a
coolant temperature between
180°F.
[82°C]
to
192°F.
[89°C]
and be fully open at
202°F.
[94°C.].
See Fig. G-7 for method of testing.

When
the thermostat is not operating properly, the engine may
run
too hot or too cold. Overheating

may
damage the thermostat so that its valve
will

not function properly, and a cold engine
will
not achieve
full
efficiency.
Rust
can also interfere with
thermostat operation. To
test
the thermostat, place

it
in water heated approximately
25°F.
[17°C]
above the temperature stamped on the thermostat

valve.
Submerge the bellows completely and agitate
the water thoroughly. The valve should open fully.
Next, place the thermostat in water heated approxi-
FIG.
G-7—THERMOSTAT
TEST

mately 10°F.
[11°C]
below the temperature
stamped on the thermostat valve. Submerge the bellows completely and agitate the water thorough­
ly.
The valve should close completely. If the ther­
mostat fails either of
these
tests, it should be re­ placed with a new one of the same type and rating.

G-10. Temperature
Sending Unit

The
sending unit incorporates a temperature sens­ ing element that when it is surrounded by cold engine coolant, the unit provides the highest resist­
ance in the temperature
gauge
indicator
circuit.
Resultant
low current flow in the circuit causes the

indicator
on the instrument panel to read at the low (C) end of the
gauge.
As engine coolant tem­

perature
increases, the resistance of the unit is
decreased allowing an increased current flow in
the
circuit,
making the instrument panel
gauge

register in proportion to the temperature of the engine coolant.

To
test
the sending unit, first run the engine until

it
has had time enough to warm up.
If
no reading is indicated on the
gauge,
check the
sending unit to
gauge
wire by removing the wire

from
the sending unit and momentarily grounding
the wire. If the
gauge
now indicates, the sending

unit
is faulty. If the
gauge
still
does
not indicate, the wire is defective.
Repair
or replace the wire,

a.
Hurricane
F4 Engine.

The
thermo-couple coolant temperature sending
unit
is mounted in the right
rear
of the cylinder head (Fig. G-8) and is connected by a single wire
to the dash unit of the instrument cluster. 166

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

FIG.
G-8—TEMPERATURE SENDING UNIT- HURRICANE
F4
ENGINE
1—Temperature
Sending Unit

b.
Dauntless V-6 Engine.

The
thermo-couple coolant sending unit is mounted
in
the left
rear
area of the intake manifold and is
connected by a single wire to the dash unit of
the instrument cluster.

G-ll.
WATER PUMP

a.
Hurricane
F4 Engine.

The
water pump on the
Hurricane
F4
engine
is a

centrifugal
impeller type of large capacity to
cir­

culate water in the entire cooling system. The double row
ball
bearing (Fig. G-9), is integral with
the shaft and is packed at assembly with a special
high melting point grease which
will
last the life of
the bearing. The bearing is sealed to retain the
lubricant
and prevent
dirt
and dust from entering.

The
bearing and shaft are retained in the water
pump body by the bearing retaining wire. The
water
seal bears against the ground seat on the
pump body and the inside of the impeller, maintain­
ing a constant pressure against both and preventing

water
leakage. A
drain
hole
in the
bottom
of the
pump body precludes any water
seepage
past the

seal
from entering the bearing.
The
impeller and the pulley hub are pressed on
the shaft under high pressure,
b.
Dauntless V-6 Engine.

A
centrifugal-type water pump, shown in
Fig.
G-10,

circulates
coolant through the Dauntless V-6
engine

and
its cooling system.
This
pump is mounted on
the timing chain cover.
Similar
to the
engine
cooling
fan
mounted on its hub, the pump is driven through
a
V-belt from the crankshaft pulley.

Coolant
enters the water pump at its center.
Centri­

fugal force then forces coolant radially outward, through vanes of the pump impeller, and backward
through two discharge passages in the timing chain cover. These passages conduct an equal amount of
coolant to each cylinder bank water jacket.
This

water
pump has a sealed double row
ball
bearing
and
a ceramic water seal, neither of which can be

serviced.
In
event
of bearing or water seal failure, the entire water pump assembly must be replaced.
G-l2.
Water
Pump Inspection

Check
the water pump for leaks, and excessive end play or
looseness
of the shaft in the pump. A

quick
way to check is to work the fan blades up
and
down by hand. If any play is noticed, this
indicates that the bearings are rough. Rough bear­ings should be checked to see if the water pump
should be replaced or rebuilt.

G-13.
Water Pump
Disassembly
—
Hurricane
F4
Engine

•
Refer to Fig. G-9.

a.
Remove the fan belt, fan blades, and fan pulley.

b.
Remove the
bolts
attaching the water pump
to the block. Remove the pump.

c.
Remove the bearing retainer spring.

d.
Remove the pump impeller and pulley with a suitable puller.

e.
Remove the pump seal, bearing and shaft, and

bearing
slinger.

G-l4.
Water Pump Reassembly
—
Hurricane
F4
Engine

•
Refer to Fig. G-9.
Before assembling the water pump, examine water
seal
seat in the pump body and should it be rough,

install
a new pump body.

To
reassemble the unit, insert the long end of the shaft into the pump body from the front end until
the outer end of the bearing is flush against the

FIG.
G-9—WATER
PUMP-
HURRICANE
F4
ENGINE

1—
Fan
and Pump Pulley
2—
Bearing
and Shaft

3—
Bearing
Retainer Spring

A—Pipe
Plug 5—
Pump
Body
6—
Seal
Washer 7—
Pump
Seal
8—
Impeller

9—
Gasket
167