octane JEEP DJ 1953 Service Manual

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

C

FIG.
C-2
7—FAN
BELT
—
DAUNTLESS
V-6
ENGINE
e. Adjust mixture by turning idle mixture screws
out (counterclockwise) until a loss of engine speed
is indicated; then, slowly
turn
both mixture screws

in
clockwise (leaner) until maximum speed (RPM)
is reached. Continue turning in (clockwise) until a slight drop in speed (RPM) is noted. Make certain
both mixture screws are adjusted equally.
This
will

ensure a "lean as possible" mixture adjustment.

Readjust
idle
stop
screw to idle engine at the
specified
R.P.M.

Note:
This
method of adjusting idle mixture must
be used to keep hydrocarbon and carbon monoxide
emissions to a minimum.

Note:
No fast idle speed adjustment is required.

Fast
idle is controlled by the curb idle speed ad­ justment screw. If the curb idle speed is correctly set, the fast idle speed
will
be correct.
C-26.
Dash
Pot
Adjustment

Refer
to Section
E, Par.
E-44 for proper carburetor

dash
pot adjustment procedure.

C-27.
Check
Fan
Belt

The
fan belt drives the fan, alternator, and water

pump.
See Fig. C-27.

Inspect
the fan belt for serviceability and proper
tension. The tension should be checked with the
Belt
Tension Gauge, W-283. The correct tension on a used belt is 70 to 80 pounds [31,7 a 36,2 kg.]

and
on a new belt 110 to 120 pounds [49,8 a 54,5 kg.]. When preparing for delivery of new car,
the belt strand tension should be 80 to 110 pounds [36,2 a 49,8 kg.]. When installing a new belt, adjust
the strand tension 110 to 120 pounds [49,8 a 54,5 kg.].

Adjust
the fan belt tension by loosening the clamp
bolt on the alternator brace and swinging the alter­

nator
away from the engine until proper belt ten­
sion is obtained.
Then
tighten the clamp bolt.

Note:
If no
gauge
is available approximate correct
tension is obtained when the thumb pressure mid­
way between the pulleys causes the belt to flex
y%
inch
[IV4
cm.].

C-28.
ROAD TEST VEHICLE

After
completing the tune-up, road
test
the vehicle for power and overall performance. Make neces­
sary
adjustments.

Note:
Engine run on or "dieseling" is a condition

in
which combustion continues to take place after
the normal ignition
spark
from the distributor has
been shut off by turning off the ignition switch. It is generally caused by excessive engine idle speed

in
combination with retarded ignition timing, en­ gine heat soak or the use of low octane fuel.

Should
engine dieseling (engine running after igni­
tion key is turned off) be experienced on V-6 engine equipped vehicles, installation of Idle Stop
Valve
Kit
Part
No. 991722
will
correct the

difficulty.
33

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

E
is generally caused by excessive
engine
idle speed

in
combination with retarded ignition timing,

engine
heat soak or the use cf low octane fuel.
Should
engine
dieseling
(engine
running after ignition key is turned off) be experienced on V-6

engine
equipped vehicles, installation of Idle Stop
Valve
Kit
Part
No.
991722
will
correct the
difficulty.

E-43.
Fast
Idle Adjustment
No fast idle speed adjustment is required.
Fast

idle is controlled by the curb idle speed adjustment

screw.
If curb idle speed is correctly set and the choke rod is properly adjusted, fast idle speed
will

be correct;

E-44.
Dash Pot Adjustment —
F4
and V-6 Engine

•
Refer to
Figs.
E-27 and E-28. Before adjusting the dash pot, the
engine
idle speed

and
mixture should be correctly adjusted.
With
the

engine
idling at normal operating temperature,
adjust
the dash pot as follows:

The
dash pot adjustment is made with the throttle
set at curb idle (not fast idle). Loosen dash pot lock
nut and
turn
the dash pot assembly until dash pot
plunger contacts the throttle lever without the plunger being depressed.
Then
turn
the dash pot
assembly 2turns against the throttle lever, de­ pressing the dash pot plunger. Tighten the lock nut
securely. As a final check, open carburetor and
allow throttle to snap closed. Time dash pot delay­ ing action from the point where the throttle lever
hits the dash pot to the point where the lever
stops

moving. The dash pot should delay or cushion
closing action for two seconds by saying, "One
thousand and one, one thousand and two."
14204

FIG.
E-27—DASH
POT
ADJUSTMENT—V6
ENGINE
1—
Throttle
Lever
3—Dash Pot
2—
Plunger
4—Lock
Nut
E-45.
FUEL
PUMP
(DOUBLE-ACTION)
—

HURRICANE
F4
ENGINE

•
Early
Models

The
double-action fuel pump consists of a metal
body, a rubber diaphragm, rocker arm, valves,
FIG.
E-28—DASH
POT
ADJUSTMENT—F4
ENGINE

1—
Throttle
Lever
3—Dash Pot
2—
Plunger
4—Lock
Nut springs, gaskets, and a glass sediment bowl complete

with
strainer.
The
metal pump body provides
a
work­
ing housing for the diaphragm, lever, valves, and springs. The fuel pump is mounted on the left side
of the
engine
and is actuated by an eccentric on the
camshaft. An air
dome
is cast into the metal cover
to relieve the carburetor
needle
valve and the fuel
pump diaphragm of excessive pressure when the

carburetor
needle
valve is closed.

Tracing
pump operation from the beginning, the
camshaft eccentric forces the diaphragm up, over­
coming spring pressure.
This
action creates a
partial
vacuum
in the pump chamber.
Fuel
from the main

tank
is forced into the low-pressure pump chamber
through the open disc valve. Incoming fuel supplies
the force necessary to open the valve, which is

a
one-way check valve. As the
engine
camshaft continues to rotate, spring pressure forces the

diaphragm
downward as the pump rocker arm
follows the camshaft eccentric to its low
spot.

The
downward action of the diaphragm
closes

the intake valve and forces fuel to the carburetor

reservoir
through the pump
outlet
valve. Both intake and
outlet
valves are one-way check valves
opened and closed by fuel flow. No mechanical components are required in the control of valve
operation.

Fuel
is delivered to the carburetor only when the float
needle
is off its seat. When the fuel level in the carburetor bowl is high enough for the float to
force the
needle
against its seat, pressure backs up
to the fuel pump air
dome
and causes the diaphragm
to
stop
pumping. In this position, the pump is said
to be balanced because the pressure in the pump- to-carburetor line equals that of the diaphragm

spring.
In this way, fuel from the pump to the
carburetor
is always under pressure. The carburetor

uses
fuel, causing the float to drop and
pull
the

carburetor
needle
valve off its seat. Pressure in the pump immediately drops as fuel is delivered to the

carburetor
reservoir. Almost instantaneously the

diaphragm
again starts operating to pump more 125