brake rotor JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual GRAND CHEROKEE 2002 WJ / 2.G JEEP JEEP https://www.carmanualsonline.info/img/16/7175/w960_7175-0.png JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual

Page 30 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual BUSHINGS
REMOVAL
(1) Remove the upper suspension arm from axle.
(2) Position Spacer 8279 over the axle bushing on
a 4x2 vehicle and right side on a 4x4 vehicle.
(3) Place Receiver 7932-1 over flanged

Page 31 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual ing (Fig. 4) from the steering knuckle and off the
axle shaft.
INSTALLATION
(1) Install the hub bearing to the knuckle.
(2) Install the hub bearing to knuckle bolts and
tighten to 102 N´m (75 ft. lbs

Page 46 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual DIFFERENTIAL & DRIVELINE
TABLE OF CONTENTS
page page
PROPELLER SHAFT......................1
FRONT TUBE AXLE......................14
FRONT AXLE - 186FBI....................15REAR AXLE - 198RBI.........

Page 47 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual DRIVELINE VIBRATION
Drive Condition Possible Cause Correction
Propeller Shaft Noise 1) Undercoating or other foreign material
on shaft.1) Clean exterior of shaft and wash with
solvent.
2) Loose U-join

Page 59 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual FRONT TUBE AXLE
TABLE OF CONTENTS
page page
FRONT TUBE AXLE
REMOVAL.............................14INSTALLATION.........................14
FRONT TUBE AXLE
REMOVAL
(1) Raise and support the vehicle.
(2)

Page 65 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual Condition Possible Causes Correction
Axle Noise 1. Insufficient lubricant. 1. Fill differential with the correct
fluid type and quantity.
2. Improper ring gear and pinion
adjustment.2. Check ring gear

Page 66 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual INSTALLATION
CAUTION: The weight of the vehicle must be sup-
ported by the springs before suspension arms and
track bar fasteners can be tightened. If springs are
not at their normal ride position, ri

Page 79 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual AXLE SHAFTS
REMOVAL
If the axle shaft and hub bearing are being
removed in order to service another component, the
axle shaft and hub bearing can be removed as an
assembly.
(1) Raise and support the v

Page 82 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual INSTALLATION
(1) Pack the bearing caps 1/3 full of wheel bearing
lubricant. Apply extreme pressure (EP), lithium-base
lubricant to aid in installation.
(2) Position the spider in the yoke. Insert the

Page 84 of 2199

JEEP GRAND CHEROKEE 2002 WJ / 2.G Workshop Manual (6) Install propeller shaft with installation refer-
ence marks aligned.
(7) Fill differential with gear lubricant.
(8) Install brake rotors and calipers.
(9) Install wheel and tire assemblies.
(10) L
Page:   1-10 11-20 21-30 31-40 40 next >