wiring JEEP GRAND CHEROKEE 2010 Owner handbook (in English)

•As the airbags deflate, you may see some
smoke-like particles. The particles are a nor-
mal by-product of the process that gener-
ates the non-toxic gas used for airbag infla-
tion. These airborne particles may irritate the
skin, eyes, nose, or throat. If you have skin or
eye irritation, rinse the area with cool water.
For nose or throat irritation, move to fresh air.
If the irritation continues, see your doctor. If
these particles settle on your clothing, follow
the garment manufacturer’s instructions for
cleaning.
Do not drive your vehicle after the airbags have
deployed. If you are involved in another colli-
sion, the airbags will not be in place to protect
you.
WARNING!
Deployed airbags and seat belt pretensioners
cannot protect you in another collision. Have
the airbags, seat belt pretensioners, and the
front seat belt retractor assemblies replaced
by an authorized dealer as soon as possible.
Also, have the Occupant Restraint Controller
(ORC) system serviced as well. Maintaining Your Airbag System
WARNING!
•
Modifications to any part of the airbag
system could cause it to fail when you need
it. You could be injured if the airbag system
is not there to protect you. Do not modify
the components or wiring, including adding
any kind of badges or stickers to the steer-
ing wheel hub trim cover or the upper right
side of the instrument panel. Do not modify
the front bumper, vehicle body structure, or
add aftermarket side steps or running
boards.
• It is dangerous to try to repair any part of
the airbag system yourself. Be sure to tell
anyone who works on your vehicle that it
has an airbag system.
(Continued)
WARNING!(Continued)
• Do not attempt to modify any part of your
advanced airbag system. The airbag may
inflate accidentally or may not function
properly if modifications are made. Take
your vehicle to an authorized dealer for any
advanced airbag system service. If your
seat, including your trim cover and cushion,
needs to be serviced in any way (including
removal or loosening/tightening of seat at-
tachment bolts), take the vehicle to your
authorized dealer. Only manufacturer ap-
proved seat accessories may be used. If it
is necessary to modify the airbag system
for persons with disabilities, contact your
authorized dealer.
44

not recommended. Doing so may block the
sensor and inhibit ACC operation.
Removing ACC Sensor For Off-Roading
NOTE:
When off-roading, it may be advisable to
remove the ACC sensor. The sensor is lo-
cated behind the front lower grille in the
center of the vehicle. After removing the
lower fascia, you may remove the lower
sensor and bracket assembly.
To remove the sensor follow these instructions:
1. Unplug the connector by depressing the two
tabs on the connector and pulling it out. Do not
pull by the wiring or using any tools to remove
the connector.
2. Remove the wiring christmas tree attach-
ment from the back of the bracket.
3. Remove the two M6 fasteners that connect
the bracket to the bumper.
NOTE:
Do not change the adjustment fasteners or
pull the sensor off of the bracket. Doing so
may misalign the sensor.Store the sensor and bracket assembly in a
safe location. The wiring and connector must
be stowed properly after the sensor and
bracket assembly is removed.
A connector plug is stowed on top of the
bumper beam. Insert the wiring connector into
the connector plug.
NOTE:
When the sensor is removed, Adaptive
Cruise Control, Normal Cruise Control, and
Forward Collision Warning will not be avail-
able. The cluster will display the warning
“ACC/FCW Unavailable - Service Radar Sen-
sor.”
To reinstall the sensor and bracket assembly
reverse the process above. The fastener torque
required to assembly the bracket back to the
beam is 6.6 ft lbs (9 Nm).
ACC Unavailable Warning
If the system turns off, and the EVIC displays
“ACC/FCW Unavailable, Vehicle System Error”,
there may be a temporary malfunction that
limits ACC functionality. Although the vehicle is
still drivable under normal conditions, ACC will
be temporarily unavailable. If this occurs, tryactivating ACC again later, following a key
cycle. If the problem persists, see your autho-
rized dealer.
Service ACC Warning
If the system turns off, and the EVIC displays
“ACC/FCW Unavailable Service Radar Sen-
sor”, it indicates there is an internal system
fault. Although the vehicle is still drivable under
normal conditions, have the system checked
by an authorized dealer.
ACC/FCW Unavailable Warning
126

Check the trailer tires for proper tire inflationpressures before trailer usage.
Check for signs of tire wear or visible tire damage before towing a trailer. Refer to
“Tires – General Information” in “Starting and
Operating” for proper inspection procedure.
When replacing tires, refer to “Tires – Gen- eral Information” in “Starting and Operating”
for proper tire replacement procedures. Re-
placing tires with a higher load carrying
capacity will not increase the vehicle’s
GVWR and GAWR limits.
Towing Requirements – Trailer Brakes
Do notinterconnect the hydraulic brake sys-
tem or vacuum system of your vehicle with
that of the trailer. This could cause inad-
equate braking and possible personal injury.
An electronically-actuated trailer brake con- troller is required when towing a trailer with
electronically-actuated brakes. When towing
a trailer equipped with a hydraulic surge-
actuated brake system, an electronic brake
controller is not required. Trailer brakes are recommended for trailers
over 1,000 lbs (454 kg), and required for
trailers in excess of 1,654 lbs (750 kg).
CAUTION!
If the trailer weighs more than 1,000 lbs
(454 kg) loaded, it should have its own brakes
and they should be of adequate capacity.
Failure to do this could lead to accelerated
brake lining wear, higher brake pedal effort,
and longer stopping distances.
WARNING!
• Do not connect trailer brakes to your vehi-
cle’s hydraulic brake lines. It can overload
your brake system and cause it to fail. You
might not have brakes when you need
them and could have an accident.
• Towing any trailer will increase your stop-
ping distance. When towing, you should
allow for additional space between your
vehicle and the vehicle in front of you.
Failure to do so could result in an accident. Towing Requirements – Trailer Lights and
Wiring
Whenever you pull a trailer, regardless of the
trailer size, stop lights and turn signals on the
trailer are required for motoring safety.
The Trailer Tow Package includes a 13 pin
wiring harness. Use a factory approved trailer
harness and connector.
NOTE:
Do not cut or splice wiring into the vehicles
wiring harness.
The electrical connections are all complete to
the vehicle but you must mate the harness to a
trailer connector.
248

more white after approximately 10 seconds,
as the system charges.
Halogen Headlamps – If Equipped
1. Open the hood.
2. Turn the low or high beam bulb one–quarter
turn counterclockwise to remove from housing.
3. Disconnect the electrical connector and re-
place the bulb.
CAUTION!
Do not touch the new bulb with your fingers.
Oil contamination will severely shorten bulb
life. If the bulb comes in contact with any oily
surface, clean the bulb with rubbing alcohol.
Front Turn Signal
1. Open the hood.
2. Turn the turn signal bulb one–quarter turn
counterclockwise to remove from housing.
3. Disconnect the electrical connector and re-
place the bulb.
CAUTION!
Do not touch the new bulb with your fingers.
Oil contamination will severely shorten bulb
life. If the bulb comes in contact with any oily
surface, clean the bulb with rubbing alcohol.
Front Fog Lamps
1. Reach through the cutout in the splash
shield and disconnect the wiring harness from
the fog lamp connector.
2. Firmly grasp the bulb by the two latches and
squeeze them together to unlock the bulb from
the back of the front fog lamp housing.
3. Pull the bulb straight out from the keyed
opening in the housing.
CAUTION!
•Do not touch the new bulb with your fin-
gers. Oil contamination will severely
shorten bulb life. If the bulb comes in
contact with any oily surface, clean the bulb
with rubbing alcohol.
• Always use the correct bulb size and type
for replacement. An incorrect bulb size or
type may overheat and cause damage to
the lamp, the socket or the lamp wiring.
4. Align the index tabs of the front fog lamp
bulb with the slots in the collar of the bulb
opening on the back of the front fog lamp
housing.
5. Insert the bulb into the housing until the
index tabs are engaged in the slots of the collar.
6. Firmly and evenly push the bulb straight into
the lamp housing until both tabs snap firmly
into place and are fully engaged.
7. Connect the wiring harness to the front fog
lamp connector.
294

Storage, Vehicle............ 192,292
Storing Your Vehicle ............292
Sun Roof ................ 140,142
Sun Visor Extension .............69
Sunglasses Storage ............140
Supplemental Restraint System -
Airbag ....................37
Suspension, Air ..............214
Sway Control, Trailer ............226
Synthetic Engine Oil ............275
Tachometer .................158
Telescoping Steering Column .......115
Temperature Control, Automatic (ATC) . . 188
Temperature Gauge, Engine Coolant . . 163
Tether Anchor, Child Restraint .......50
Tie Down Hooks, Cargo ..........149
Tilt Steering Column ............115
Tip Start ..................203
Tires ................... 57,230
Air Pressure ...............230
Chains ..................231
Changing ................259
High Speed ...............231
Inflation Pressures ...........230
Jacking ..................259 Pressure Monitor System (TPMS) . . . 234
Pressure Warning Light
.........160
Radial ..................231
Replacement ..............233
Rotation .................234
Spare Tire ................259
Spinning .................231
Tread Wear Indicators .........232
Wheel Mounting .............261
Tongue Weight/Trailer Weight .......246
Torque Converter Clutch .........209
Tow/Haul Indicator Light .........159
Towing ................. 244,265
Disabled Vehicle ............265
Guide ..................246
Recreational ...............251
Weight ..................246
Towing Eyes ................264
Traction Control ..............224
Trailer Sway Control (TSC) ........226
Trailer Towing ................244
Cooling System Tips ..........250
Hitches ..................250
Minimum Requirements .........247
Trailer and Tongue Weight .......246
Wiring ..................248
Trailer Towing Guide ............246 Trailer Weight................246
Transfer Case ...............284
Maintenance ...............284
Transmission Automatic .............. 206,285
Maintenance ...............285
Shifting ..................204
Transmitter Battery Service
(Remote Keyless Entry) ...........18
Transmitter Programming
(Remote Keyless Entry) ...........17
Transmitter, Remote Keyless Entry
(RKE) .....................17
Tread Wear Indicators ...........232
Turn Signals ........... 159,294,295
UCI Connector ...............181
uconnect (Hands-Free Phone) ......74
Universal Consumer Interface (UCI)
Connector .................181
Untwisting Procedure, Seat Belt ......32
Upholstery Care ..............288
Vanity Mirrors ................69
Variance, Compass ............175
Vehicle Identification Number (VIN) .....8
343