airbag JEEP GRAND CHEROKEE 2011 Owner handbook (in English)

pending on the severity and type of collision. In
these events, the ORC will deploy the SABIC
only on the impact side of the vehicle.
A quantity of non-toxic gas is generated to
inflate the side curtain airbag. The inflating side
curtain airbag pushes the outside edge of the
headliner out of the way and covers the win-
dow. The airbag inflates in about 30 ms (about
one-quarter of the time that it takes to blink your
eyes) with enough force to injure you if you are
not belted and seated properly, or if items are
positioned in the area where the side curtain
airbag inflates. This especially applies to chil-
dren. The side curtain airbag is only about
3-1/2 in (9 cm) thick when it is inflated.
Because airbag sensors estimate deceleration
over time, vehicle speed and damage are not
good indicators of whether or not an airbag
should have deployed.
NOTE:
In a rollover the pretensioners, and/or SAB
and SABIC airbags may deploy on both
sides of the vehicle.Front and Side Impact Sensors
In front and side impacts, impact sensors can
aid the ORC in determining appropriate re-
sponse to impact events. Additional sensors in
the ORC determine the level of airbag deploy-
ment and provide verification.
Enhanced Accident Response System
In the event of an impact causing airbag de-
ployment, if the communication network re-
mains intact, and the power remains intact,
depending on the nature of the event the ORC
will determine whether to have the Enhanced
Accident Response System perform the follow-
ing functions:
•
Cut off fuel to the engine.
• Flash hazard lights as long as the battery
has power or until the ignition key is turned
off.
• Turn on the interior lights, which remain on as
long as the battery has power or until the
ignition key is removed.
• Unlock the doors automatically. If a Deployment Occurs
The Advanced Front Airbags are designed to
deflate immediately after deployment.
NOTE:
Front and/or side airbags will not deploy in
all collisions. This does not mean some-
thing is wrong with the airbag system.
If you do have a collision which deploys the
airbags, any or all of the following may occur:
•
The nylon airbag material may sometimes
cause abrasions and/or skin reddening to
the driver and front passenger as the air-
bags deploy and unfold. The abrasions are
similar to friction rope burns or those you
might get sliding along a carpet or gymna-
sium floor. They are not caused by contact
with chemicals. They are not permanent and
normally heal quickly. However, if you
haven’t healed significantly within a few
days, or if you have any blistering, see your
doctor immediately.
43

•As the airbags deflate, you may see some
smoke-like particles. The particles are a nor-
mal by-product of the process that gener-
ates the non-toxic gas used for airbag infla-
tion. These airborne particles may irritate the
skin, eyes, nose, or throat. If you have skin or
eye irritation, rinse the area with cool water.
For nose or throat irritation, move to fresh air.
If the irritation continues, see your doctor. If
these particles settle on your clothing, follow
the garment manufacturer’s instructions for
cleaning.
Do not drive your vehicle after the airbags have
deployed. If you are involved in another colli-
sion, the airbags will not be in place to protect
you.
WARNING!
Deployed airbags and seat belt pretensioners
cannot protect you in another collision. Have
the airbags, seat belt pretensioners, and the
front seat belt retractor assemblies replaced
by an authorized dealer as soon as possible.
Also, have the Occupant Restraint Controller
(ORC) system serviced as well. Maintaining Your Airbag System
WARNING!
•
Modifications to any part of the airbag
system could cause it to fail when you need
it. You could be injured if the airbag system
is not there to protect you. Do not modify
the components or wiring, including adding
any kind of badges or stickers to the steer-
ing wheel hub trim cover or the upper right
side of the instrument panel. Do not modify
the front bumper, vehicle body structure, or
add aftermarket side steps or running
boards.
• It is dangerous to try to repair any part of
the airbag system yourself. Be sure to tell
anyone who works on your vehicle that it
has an airbag system.
(Continued)
WARNING!(Continued)
• Do not attempt to modify any part of your
advanced airbag system. The airbag may
inflate accidentally or may not function
properly if modifications are made. Take
your vehicle to an authorized dealer for any
advanced airbag system service. If your
seat, including your trim cover and cushion,
needs to be serviced in any way (including
removal or loosening/tightening of seat at-
tachment bolts), take the vehicle to your
authorized dealer. Only manufacturer ap-
proved seat accessories may be used. If it
is necessary to modify the airbag system
for persons with disabilities, contact your
authorized dealer.
44

Airbag Warning LightYou will want to have the airbags
ready to inflate for your protection
in a collision. The airbag system is
designed to be maintenance free,
if any of the following occurs, have
an authorized dealer service the
airbag system immediately.
• The Airbag Warning Light does not come on
during the four to eight seconds when the
ignition switch is first turned to the ON/RUN
position.
• The Airbag Warning Light remains on after
the four to eight-second interval.
• The Airbag Warning Light comes on intermit-
tently or remains on while driving. NOTE:
If the speedometer, tachometer, or any en-
gine related gauges are not working, the
Occupant Restraint Controller (ORC) may
also be disabled. The airbags may not be
ready to inflate for your protection. Promptly
check the fuse block for blown fuses. Refer
to the label located on the inside of the fuse
block cover for the proper airbag fuses. See
your authorized dealer if the fuse is good.
Event Data Recorder (EDR)This vehicle is equipped with an event data
recorder (EDR). The main purpose of an EDR is
to record, in certain crash or near crash-like
situations, such as an air bag deployment or
hitting a road obstacle, data that will assist in
understanding how a vehicle’s systems per- formed. The EDR is designed to record data
related to vehicle dynamics and safety systems
for a short period of time, typically 30 seconds
or less. The EDR in this vehicle is designed to
record such data as:
•
How various systems in your vehicle were
operating;
• Whether or not the driver and passenger
safety belts were buckled/fastened;
• How far (if at all) the driver was depressing
the accelerator and/or brake pedal; and,
• How fast the vehicle was traveling.
These data can help provide a better under-
standing of the circumstances in which crashes
and injuries occur.
45

IL = Suitable for particular ISOFIX child restraint
systems (CRS) given in the attachment list.
These ISOFIX CRS are those of the “specific
vehicle”, “restricted” or “semi-universal” cat-
egories.
X = ISOFIX position not suitable for ISOFIX
child restraint systems in this mass group
and/or this size class.
Children 12 years and under should ride prop-
erly buckled up in a rear seat, if available.
According to crash statistics, children are safer
when properly restrained in the rear seats
rather than in the front.
There are different sizes and types of restraints
for children from newborn size to the child
almost large enough for an adult safety belt.
Always check the child seat Owner’s Manual to
ensure you have the right seat for your child.
Use the restraint that is correct for your child.WARNING!
In an collision, an unrestrained child, even a
tiny baby, can become a projectile inside the
vehicle. The force required to hold even an
infant on your lap can become so great that
you could not hold the child, no matter how
strong you are. The child and others could be
badly injured. Any child riding in your vehicle
should be in a proper restraint for the child’s
size.
Infants and Child Restraints
• Safety experts recommend that children ride
rearward-facing in the vehicle until they are
at least one year old and weigh at least
20 lbs (9 kg). Two types of child restraints
can be used rearward-facing: infant carriers
and convertible child seats.
• The infant carrier is only used rearward-
facing in the vehicle. It is recommended for
children who weigh up to about 20 lbs (9 kg).
Convertible child seats often have a higher
weight limit in the rearward-facing direction
than infant carriers do, so they can be used rearward-facing by children who weigh more
than 20 lbs (9 kg) but are less than one year
old. Both types of child restraints are held in
the vehicle by the lap/shoulder belt or the
ISOFIX child restraint anchorage system
(Refer to “ISOFIX — Child Seat Anchorage
System”)
When using certain Child Restraint Systems
with rigid attachments ISOFIX and foot stands
extending to the vehicle floor, remove the ve-
hicle floor mat prior to installation to ensure a
secure fit. Refer to the Child Restraint Owner’s
Manual for additional information.
WARNING!
• Rearward-facing child seats must never be
used in the front seat of a vehicle with the
front passenger airbag unless the airbag is
turned off. An airbag deployment could
cause severe injury or death to infants in
this position.
(Continued)
48

WARNING!(Continued)
• Improper installation can lead to failure of
an infant or child restraint. It could come
loose in a collision. The child could be
badly injured or killed. Follow the manufac-
turer’s directions exactly when installing an
infant or child restraint.
• A rearward-facing infant restraint should
only be used in a rear seat. A rearward-
facing infant restraint in the front seat may
be struck by a deploying passenger airbag
which may cause severe or fatal injury to
the infant.
Here are some tips for getting the most out of
your child restraint:
• Before buying any restraint system, make
sure that it has a label certifying that it meets
all applicable Safety Standards. Chrysler
Group LLC also recommends that you try a
child restraint in the vehicle seats where you
will use it before you buy it. •
The restraint must be appropriate for your
child’s weight and height. Check the label on
the restraint for weight and height limits.
• Carefully follow the instructions that come
with the restraint. If you install the restraint
improperly, it may not work when you need it.
• Except for the second row center seating
position, all passenger seat belts are
equipped with cinching latch plates. The
second row center position has an automatic
locking retractor. Both types of seat belts are
designed to keep the lap portion tight
around the child restraint so that it is not
necessary to use a locking clip. If the seat
belt has a cinching latch plate, pulling up on
the shoulder portion of the lap/shoulder belt
will tighten the belt (the cinching latch plate
will keep the belt tight; however, any seat belt
system will loosen with time, so check the
belt occasionally and pull it tight if neces-
sary). For the second row center seat belt
with the automatic locking retractor, pull the
belt from the retractor until there is enough
allowance to pass it through the child re-
straint and slide the latch plate into the
buckle. Then, pull the belt until it is fully extended from the retractor. Allow the belt to
return into the retractor, pulling on the excess
webbing to tighten the lap portion around the
child restraint. For additional information, re-
fer to
Automatic Locking Mode .
• In the rear seat, you may have trouble tight-
ening the lap/shoulder belt on the child re-
straint because the buckle or latch plate is
too close to the belt path opening on the
restraint. Disconnect the latch plate from the
buckle and twist the short buckle-end belt
several times to shorten it. Insert the latch
plate into the buckle with the release button
facing out.
• If the belt still cannot be tightened, or if
pulling and pushing on the restraint loosens
the belt, disconnect the latch plate from the
buckle, turn the buckle around, and insert
the latch plate into the buckle again. If you
still cannot make the child restraint secure,
try a different seating position.
• Buckle the child into the restraint exactly as
the manufacturer’s instructions tell you.
• When your child restraint is not in use, se-
cure it in the vehicle with the seat belt or
49

WARNING!
•An incorrectly anchored tether strap could
lead to increased head motion and possible
injury to the child. Use only the anchor
positions directly behind the child seat to
secure a child restraint top tether strap.
• Do not use the cargo tie downs located on
the load floor. Improper usage of the tether
can lead to a failure of an infant or child
restraint. The child could be badly injured
or killed. Transporting Pets
Airbags deploying in the front seat could harm
your pet. An unrestrained pet will be thrown
about and possibly injured, or injure a passen-
ger during panic braking or in an accident. Pets
should be restrained in the rear seat in pet
harnesses or pet carriers that are secured by
seat belts.
ENGINE BREAK-IN
RECOMMENDATIONS
A long break-in period is not required for the
engine and drivetrain (transmission and axle) in
your vehicle.
Drive moderately during the first 300 miles
(500 km). After the initial 60 miles (100 km),
speeds up to 50 or 55 mph (80 or 90 km/h) are
desirable.
While cruising, brief full-throttle acceleration
within the limits of local traffic laws, contributes
to a good break-in. Wide-open throttle accel-
eration in low gear can be detrimental and
should be avoided.
The engine oil installed in the engine at the
factory is a high-quality energy conserving type
lubricant. Oil changes should be consistent
with anticipated climate conditions under
which vehicle operations will occur. For the
recommended viscosity and quality grades re-
fer to “Maintenance Procedures” in “Maintain-
ing Your Vehicle”. NON-DETERGENT OR
STRAIGHT MINERAL OILS MUST NEVER BE
USED.
A new engine may consume some oil during its
first few thousand miles (kilometers) of opera-
tion. This should be considered a normal part
of the break-in and not interpreted as an indi-
cation of difficulty.
Additional Requirements For Diesel
Engine — If Equipped
During the first 1500 km avoid heavy loads, e.g.
driving at full throttle. Do not exceed 2/3 of the
maximum permissible engine speed for each
gear. Change gear in good time. Do not shift
down a gear manually in order to brake.
Top Tether Strap Mounting
54

Safety Checks You Should Make
Inside the Vehicle
Seat Belts
Inspect the belt system periodically, checking
for cuts, frays, and loose parts. Damaged parts
must be replaced immediately. Do not disas-
semble or modify the system.
Front seat belt assemblies must be replaced
after a collision. Rear seat belt assemblies must
be replaced after a collision if they have been
damaged (i.e., bent retractor, torn webbing,
etc.). If there is any question regarding belt or
retractor condition, replace the belt.Airbag Warning Light
The light should come on and remain on for four
to eight seconds as a bulb check when the
ignition switch is first turned ON. If the light is
not lit during starting, see your authorized
dealer. If the light stays on, flickers, or comes
on while driving, have the system checked by
an authorized dealer.
Defroster
Check operation by selecting the defrost mode
and place the blower control on high speed.
You should be able to feel the air directed
against the windshield. See your authorized
dealer for service if your defroster is inoper-
able.Floor Mat Safety Information
Always use floor mats designed to fit the foot
well of your vehicle. Use only floor mats that
leave the pedal area unobstructed and that are
firmly secured so that they cannot slip out of
position and interfere with the pedals or impair
safe operation of your vehicle in other ways.
WARNING!
Pedals that cannot move freely can cause
loss of vehicle control and increase the risk of
serious personal injury.
•
Always make sure that floor mats are prop-
erly attached to the floor mat fasteners.
• Never place or install floor mats or other
floor coverings in the vehicle that cannot be
properly secured to prevent them from
moving and interfering with the pedals or
the ability to control the vehicle.
(Continued)
56

INSTRUMENT CLUSTER
DESCRIPTIONS
1. Tachometer
Indicates the engine speed in revolutions per
minute (RPM).
2. Airbag Warning Light
This light will turn on for four to eight
seconds as a bulb check when the
ignition switch is first turned to the
ON/RUN position. If the light is ei-
ther not on during starting, stays on,
or turns on while driving, then have
the system inspected at an authorized dealer as
soon as possible. Refer to “Occupant Re-
straints” in “Things To Know Before Starting Your
Vehicle” for further information.
3. Malfunction Indicator Light (MIL) The Malfunction Indicator Light (MIL)
is part of an onboard diagnostic sys-
tem called OBD II that monitors en-
gine and automatic transmission con-
trol systems. The light will illuminate
when the key is in the ON/RUN position before
engine start. If the bulb does not come on when turning the key from OFF to ON/RUN, have the
condition checked promptly.
Certain conditions such as a loose or missing
gas cap, poor fuel quality, etc., may illuminate
the light after engine start. The vehicle should
be serviced if the light stays on through several
of your typical driving cycles. In most situa-
tions, the vehicle will drive normally and will not
require towing.
CAUTION!
Prolonged driving with the MIL on could cause
damage to the engine control system. It also
could affect fuel economy and drivability. If the
MIL is flashing, severe catalytic converter
damage and power loss will soon occur. Im-
mediate service is required.
WARNING!
A malfunctioning catalytic converter, as refer-
enced above, can reach higher temperatures
than in normal operating conditions. This can
cause a fire if you drive slowly or park over
flammable substances such as dry plants or
wood or cardboard, etc. This could result in
death or serious injury to the driver, occupants
or others.
4. Electronic Stability Control (ESC)
Activation/Malfunction Indicator Light —
If Equipped The “ESC Activation/Malfunction
Indicator Light” in the instrument
cluster will come on when the igni-
tion switch is turned to the ON/
RUN position. It should go out with
the engine running. If the “ESC
Activation/Malfunction Indicator Light” comes
on continuously with the engine running, a
malfunction has been detected in the ESC
system. If this light remains on after several
ignition cycles, and the vehicle has been driven
several miles (kilometers) at speeds greater
158

Adaptive Cruise Control (ACC)
(Cruise Control)..............118
Adding Fuel ................242
Additives, Fuel ...............241
Air Cleaner, Engine (Engine Air
Cleaner Filter) ...............276
Air Conditioner Maintenance .......277
Air Conditioning ..............186
Air Conditioning Controls .........186
Air Conditioning, Operating Tips .....192
Air Conditioning Refrigerant .......277
Air Conditioning System .......186,188
Air Filter ...................276
Air Pressure, Tires .............230
Air Suspension ...............214
Airbag .................. 37,42
Airbag Deployment .............43
Airbag Light ........... 41,45,56,158
Airbag Maintenance ............44
Airbag, Side ............. 38,41,42
Airbag, Window (Side Curtain) . . . 39,41,42
Alarm (Security Alarm) ..........163
Alarm System (Security Alarm) ......15
Alterations/Modifications, Vehicle ......8
Antifreeze (Engine Coolant) ........297
Anti-Lock Brake System (ABS) ......223
Anti-Lock Warning Light ..........162 Anti-Theft System
.............163
Appearance Care .............287
Assist, Hill Start ..............227
Auto Down Power Windows ........25
Automatic Dimming Mirror .........67
Automatic Door Locks ...........21
Automatic Headlights ...........106
Automatic Temperature Control (ATC) . . 188
Automatic Transmission .......206,285
Adding Fluid ...............286
Fluid and Filter Changes ........285
Fluid Level Check .........285,286
Fluid Type ................285
Special Additives ............285
Torque Converter ............209
Autostick ..................206
Auxiliary Electrical Outlet (Power
Outlet) ...................144
Auxiliary Power Outlet ...........144
Battery ...................276
Keyless Transmitter Replacement
(RKE) ...................18
Belts, Seat ................ 29,56
Blind Spot Monitoring ............69
Body Mechanism Lubrication .......277Brake Assist System............224
Brake Control System, Electronic .....223
Brake Fluid .................283
Brake System ...............283
Anti-Lock (ABS) .............223
Fluid Check ...............283
Master Cylinder .............283
Parking ..................222
Warning Light ..............161
Brake/Transmission Interlock .......205
Break-In Recommendations, New
Vehicle ....................54
Bulb Replacement .............293
Bulbs, Light .................57
Calibration, Compass ...........175
Camera, Rear ...............138
Capacities, Fluid ..............297
Caps, Filler Fuel ....................242
Power Steering .............221
Radiator (Coolant Pressure) ......281
Car Washes ................287
Carbon Monoxide Warning .........55
Cargo Area Cover .............149
Cargo Area Features ...........148
336

Gas Cap (Fuel Filler Cap)....242,244,273
Gasoline, Clean Air ............241
Gasoline (Fuel) ...............240
Conserving ...............171
Gauges Coolant Temperature ..........163
Fuel ....................162
Speedometer ..............162
Tachometer ...............158
Gear Ranges ................206
General Information ........15,19,239
Glass Cleaning ...............289
Gross Axle Weight Rating .........244
Gross Vehicle Weight Rating .......244
Hands-Free Phone (uconnect ) ......74
Hazard Warning Flasher .........258
Headlights .................293
Bulb Replacement ...........294
Cleaning .................289
On With Wipers .............107
Replacing ................294
Heated Mirrors ...............68
Heater ...................186
High Beam Indicator ...........159
Hill Descent Control ............228 Hill Descent Control Indicator
......159
Hill Start Assist ...............227
Holder, Cup ................146
Hood Release ...............105
Ignition ....................13
Key ................... 12,13
Ignition Key Removal ............13
Illuminated Entry ..............16
Immobilizer (Sentry Key) ..........14
Infant Restraint .............. 46,48
Inflation Pressure Tires ..........230
Information Center, Vehicle ........163
Inside Rearview Mirror ...........67
Instrument Cluster .............158
Instrument Panel and Controls ......156
Instrument Panel Lens Cleaning .....289
Integrated Power Module (Fuses) ....290
Interior Appearance Care .........288
Intermittent Wipers (Delay Wipers) ....113
Introduction ..................4
Jack Location ...............259
Jack Operation ............ 259,260
Jacking Instructions ............260
Jump Starting
...............262 Key, Programming
.............15
Key, Replacement ..............14
Key, Sentry (Immobilizer) ..........14
Key-In Reminder ..............14
Keyless Entry System ............17
Keyless Go ............... 12,174
Keys .....................12
Lap/Shoulder Belts .............29
LATCH (Lower Anchors and Tether for
CHildren) ................. 50,51
Latches ...................57
Lead Free Gasoline ............240
Leaks, Fluid .................57
Liftgate ....................26
Liftgate Flipper Glass ............26
Liftgate Window Wiper/Washer ......150
Light Bulbs ..................57
Lights .................. 57,106
Airbag ............. 41,45,56,158
Anti-Lock .................162
Automatic Headlights ..........106
Back-Up .................295
Brake Assist Warning ..........229
Brake Warning ..............161
Bulb Replacement ...........293
339