navigation system JEEP GRAND CHEROKEE 2013 WK2 / 4.G Owners Manual

▫Adaptive Cruise Control (ACC) Menu.......230
▫Display Warnings And Maintenance........232
▫Precautions While Driving With ACC.......236
▫General Information...................239
▫Normal (Fixed Speed) Cruise Control Mode . . .239
▫Forward Collision Warning — If Equipped. . . .241
PARKSENSE® REAR PARK ASSIST — IF
EQUIPPED...........................246
▫ParkSense® Sensors....................246
▫ParkSense® Warning Display.............247
▫ParkSense® Display....................248
▫Enabling And Disabling ParkSense®........251
▫Service The ParkSense® Rear Park Assist
System.............................252▫Cleaning The ParkSense® System..........252
▫ParkSense® System Usage Precautions.......253
PARKVIEW® REAR BACK UP CAMERA — IF
EQUIPPED...........................255
▫Turning ParkView® On Or Off — With
Navigation/Multimedia Radio............257
▫Turning ParkView® On Or Off — Without
Navigation/Multimedia Radio............257
OVERHEAD CONSOLE..................258
▫Front Map/Reading Lights..............258
▫Courtesy Lights.......................259
▫Sunglasses Bin Door...................260
GARAGE DOOR OPENER — IF EQUIPPED . . .260
▫Before You Begin Programming HomeLink® . .262
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119

NOTE:If snow, ice, mud, or any foreign substance
builds up on the camera lens, clean the lens, rinse with
water, and dry with a soft cloth. Do not cover the lens.
Turning ParkView® On Or Off — With
Navigation/Multimedia Radio
1. Press the “menu” hard-key.
2. Select “system setup” soft-key.
3. Press the “camera setup” soft-key.
4. Enable or disable the rear camera feature by selecting
the “enable rear camera in reverse” soft-key.
5. Press the “save” soft-key.
Turning ParkView® On Or Off — Without
Navigation/Multimedia Radio
1. Press the “menu” hard-key.
2. Select “system setup” soft-key.
3. Enable or disable the rear camera feature by selecting
“enable rear camera in reverse” soft-key.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 257

Elapsed Time
Shows the total elapsed time of travel since the last reset
when the ignition switch is in the ACC position. Elapsed
time will increment when the ignition switch is in the ON
or START position.
To Reset The Display
Press and release the UP or DOWN button until “Vehicle
Info” displays in the EVIC and press the SELECT button.
Press the UP and DOWN button to scroll through the
available information displays, then press SELECT to
display any one of the following choices.
Units
Press and release the UP or DOWN button until “Units”
displays highlighted in the EVIC and press the SELECT
button. The EVIC, odometer, and navigation system (if
equipped) can be changed between English and Metric
units of measure. To make your selection, scroll up ordown until the preferred setting is highlighted, then
press and release the SELECT button until a check-mark
appears next to the setting, showing that the setting has
been selected.
Vehicle Info (Customer Information Features)
Press and release the UP or DOWN button until “Vehicle
Info” displays in the EVIC and press the SELECT button.
Press the UP and DOWN button to scroll through the
available information displays, then press SELECT to
display any one of the following choices.
•Coolant Temp
Displays the actual coolant temperature.
•Oil Temperature
Displays the actual oil temperature.
•Oil Pressure
Displays the actual oil pressure.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 333

Select Language
When in this display you may select one of five lan-
guages for all display nomenclature, including the trip
functions and the navigation system (if equipped). Press
the UP or DOWN button while in this display and scroll
through the language choices. Press the SELECT button
to select English, Spanish (Español), French (Français),
Italian (Italiano), German (Deutsch), and Dutch (Neder-
lands). Then, as you continue, the information will dis-
play in the selected language.
Nav–Turn By Turn
When this feature is selected, the navigation system utilizes
voice commands, guiding through the drive route, mile by
mile, turn-by-turn until the final destination is reached. To
make your selection, press and release the SELECT button
until a check-mark appears next to the feature showing the
system has been activated or the check-mark is removed
showing the system has been deactivated.
Auto Unlock Doors
When this feature is selected, all doors will unlock when
the vehicle is stopped and the transmission is in the
PARK or NEUTRAL position and the driver’s door is
opened. To make your selection, press and release the
SELECT button until a check-mark appears next to the
feature showing the system has been activated, or the
check-mark is removed showing the system has been
deactivated.
Remote Unlock Sequence
WhenUnlock Driver Door Only On 1st Pressis selected,
only the driver’s door will unlock on the first press of the
RKE transmitter UNLOCK button. When Driver Door 1st
Press is selected, you must press the RKE transmitter
UNLOCK button twice to unlock the passenger’s doors.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 339

Mode Selection MenuThe first press of the MODE button causes the Mode
Selection menu to appear on screen. The current mode is
always the default selection. The mode can be changed
for either Channel/Screen 1 or Channel/Screen 2 using
the remote control.
Use the remote control’s navigation buttons (,,,)
to navigate through the available modes, and then press
the remote control’s ENTER button to select the mode.
An alternate method of changing modes is repeated
pressing of the MODE button until the desired mode is
highlighted then press the ENTER button on the remote
control to select the mode.
In a single screen system, when a video mode (such as
DVD-video, Aux video, etc.) is active and Channel/
Screen 1 is selected using the remote control selector
switch, the first press of the remote control’s MODE
button causes the Mode Selection menu to appear.
Mode Selection Menu
402 UNDERSTANDING YOUR INSTRUMENT PANEL