homelink JEEP GRAND CHEROKEE LIMITED 2019 Owners Manual

▫Auto-Up Feature With Anti-Pinch Protection ....97
▫ Reset Auto-Up ..........................98
▫ Window Lockout Switch ...................98
▫ Wind Buffeting .........................98
 POWER SUNROOF — IF EQUIPPED ..........99
▫ Opening Sunroof .......................99
▫ Closing Sunroof .......................100
▫ Wind Buffeting ....................... .100
▫ Sunshade Operation ................... .100
▫ Pinch Protect Feature ................... .101
▫ Venting Sunroof — Express ...............101
▫ Sunroof Maintenance ................... .101
▫ Relearn Procedure ..................... .101
 COMMANDVIEW SUNROOF WITH POWER
SHADE — IF EQUIPPED ..................102
▫ Opening Sunroof .......................103
▫ Closing Sunroof .......................103 ▫
Wind Buffeting ....................... .104
▫ Opening Power Shade .................. .104
▫ Closing Power Shade ................... .104
▫ Pinch Protect Feature ................... .105
▫ Venting Sunroof — Express ...............105
▫ Sunroof Maintenance ................... .105
 HOOD .............................. .106
▫ To Open The Hood .....................106
▫ To Close The Hood .....................106
 LIFTGATE ............................ .107
▫ Opening ............................ .107
▫ Closing ............................ .108
▫ Power Liftgate

— If Equipped .............109
▫ Cargo Area Features ....................111
 GARAGE DOOR OPENER — IF EQUIPPED ....114
▫ Before You Begin Programming HomeLink .....114
▫ Canadian/Gate Operator Programming .......117
16 GETTING TO KNOW YOUR VEHICLE

▫Using HomeLink .......................118
▫ Security ..............................119
▫ Troubleshooting Tips ....................119
▫ General Information .....................120
 INTERNAL EQUIPMENT ..................120
▫ Storage ............................. .120▫
Cupholders ......................... .124
▫ Electrical Power Outlets ..................125
▫ Power Inverter — If Equipped .............129
▫ Sunglasses Bin Door ................... .130
 ROOF LUGGAGE RACK — IF EQUIPPED ......130
3
GETTING TO KNOW YOUR VEHICLE 17

WARNING!(Continued)
•Place as much cargo as possible in front of the rear
axle. Too much weight or improperly placed weight
over or behind the rear axle can cause the rear of the
vehicle to sway.
• Do not pile luggage or cargo higher than the top of
the seatback. This could impair visibility or become
a dangerous projectile in a sudden stop or accident.
GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three hand-held transmitters that
operate devices such as garage door openers, motorized
gates, lighting or home security systems. The HomeLink
unit is powered by your vehicle’s 12 Volt battery.
The HomeLink buttons, located on the overhead console,
designate the three different HomeLink channels. The
HomeLink indicator is located above the center button. NOTE:
HomeLink is disabled when the Vehicle Security
Alarm is active.
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmission
of the radio-frequency signal it is recommended that a new
battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system.

To erase the channels, place the ignition in the ON/RUN
position, and push and hold the two outside HomeLink
buttons (I and III) for up to 20 seconds or until the orange
indicator flashes.
NOTE:
•Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manufac-
tured after 1995. These garage door openers can be identi-
fied by the “LEARN” or “TRAIN” button located where
the hanging antenna is attached to the garage door opener.
NOTE: It is NOT the button that is normally used to open
and close the door. The name and color of the button may
vary by manufacturer. 1. Place the ignition in the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)
away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans-
mitter button.

4. Continue to hold both buttons and observe the indicatorlight. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually
be found where the hanging antenna wire is attached to
the garage door opener/device motor. Firmly push and
release the “LEARN” or “TRAINING” button. On some
garage door openers/devices there may be a light that
blinks when the garage door opener/device is in the
LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed.
6. Return to the vehicle and push the programmed HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not activate,
push the button a third time (for two seconds) to complete
the training. To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.
Reprogramming A Single HomeLink Button (Rolling
Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program- ming A Rolling Code” step 2 and follow all remaining
steps.
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Cycle the ignition to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
116 GETTING TO KNOW YOUR VEHICLE

3. Press and hold the HomeLink button you want toprogram while you press and hold the hand-held trans-
mitter button.
4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. Press and hold the programmed HomeLink button and observe the indicator light.
• If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
Reprogramming A Single HomeLink Button (Non-
Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position. 2. Press and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Program- ming A Non-Rolling Code” step 2 and follow all remain-
ing steps.
Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian radio frequency laws require transmitter signals
to time-out (or quit) after several seconds of transmission –
which may not be long enough for HomeLink to pick up
the signal during programming. Similar to this Canadian
law, some U.S. gate operators are designed to time-out in
the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage door
or gate motor.
1. Cycle the ignition to the ON/RUN position.
3
GETTING TO KNOW YOUR VEHICLE 117

2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Continue to press and hold the HomeLink button, while you press and release (“cycle”) your hand-held trans-
mitter every two seconds until HomeLink has success-
fully accepted the frequency signal. The indicator light
will flash slowly and then rapidly when fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds or longer in rare cases. The garage door may
open and close while you are programming.
5. Press and hold the programmed HomeLink button and observe the indicator light.
NOTE: •If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels. If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink Button (Canadian/
Gate Operator)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Press and hold the desired HomeLink button until the
indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Canadian/ Gate Operator Programming” step 2 and follow all
remaining steps.
Using HomeLink
To operate, push and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e. garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.). The
hand-held transmitter of the device may also be used at
any time.
118 GETTING TO KNOW YOUR VEHICLE

Security
It is advised to erase all channels before you sell or turn in
your vehicle.
To do this, push and hold the two outside buttons for 20
seconds until the orange indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
The HomeLink Universal Transceiver is disabled when the
Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink, here
are some of the most common solutions:
•Replace the battery in the Garage Door Opener hand-
held transmitter.
• Push the LEARN button on the Garage Door Opener to
complete the training for a Rolling Code.
• Did you unplug the device for programming and re-
member to plug it back in? If you have any problems, or require assistance, please call
toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.

Overhead Console
The overhead console contains courtesy/reading lights
and storage for sunglasses. Universal Garage Door Opener
(HomeLink), power liftgate and power sunroof switches
may also be included, if equipped.
Cupholders
There are two cupholders for the front seat passengers
located in the center console.
Front Cupholders
124 GETTING TO KNOW YOUR VEHICLE

Gasoline.............................. .501
Light ................................ .155
Materials Added ........................ .502
Methanol ............................. .502
Octane Rating ....................... .501, 506
Requirements .......................... .501
Tank Capacity .......................... .505
Fueling ................................. .359
Fuses .................................. .405
Garage Door Opener (HomeLink) ...............114
Gasoline, Clean Air ........................ .502
Gasoline, (Fuel) ........................... .501
Gasoline, Reformulated ..................... .502
Gear Ranges ............................. .266
Glass Cleaning ........................... .495
Glove Compartment Storage ...................120
Gross Axle Weight Rating .....................365
Gross Vehicle Weight Rating ...................364
GVWR ................................. .362
Hazard Warning Flashers .....................392
Headlights Cleaning .............................. .492
Delay ..................................74 High Beam/Low Beam Select Switch
...........73
Lights On Reminder .......................75
On With Wipers ..........................74
Passing ................................73
Switch .................................71
Washers ................................85
Headlight Washers ..........................85
Head Restraints ............................58
Head Rests ................................58
Heated Mirrors .............................70
Heated Seats ...............................54
Heated Steering Wheel .....................63, 64
Heater, Engine Block ....................... .258
Hill Descent Control ....................... .176
Hill Descent Control Indicator .................176
Hill Start Assist ........................... .168
Hitches Trailer

Towing .......................... .366
Hood Closing ............................... .106
Opening .............................. .106
Hood Prop .............................. .106
Hood Release ............................ .106
Ignition ..................................25
12
INDEX 613