License plate light JEEP LIBERTY 2002 KJ / 1.G User Guide
[x] Cancel search | Manufacturer: JEEP, Model Year: 2002, Model line: LIBERTY, Model: JEEP LIBERTY 2002 KJ / 1.GPages: 1803, PDF Size: 62.3 MB
Page 540 of 1803
SPECIFICATIONS - LAMPS/LIGHTING -
EXTERIOR
BULB SPECIFICATIONS
LAMP BULB
Backup 3157 P27/7W
Brake 3157 P27/7W
Center High Mounted
Stop921/W16W
Front Fog 9145
Front Park 3157 P27/7W
Front Position W5W
Front Side Marker 168
Front Turn 3157 P27/7W
Headlamp (North
America)9007QL
Headlamp (Rest-Of-
World)H-4 W0W6
License Plate (North
America)168
License Plate (Rest-Of-
World)W5W
Rear Fog 3157 P27/7W
Rear Park/Tail 3157 P27/7W
Rear Turn 3157 P27/7W
Side Repeater W5W
BACKUP LAMP SWITCH
DESCRIPTION
Vehicles equipped with a manual transmission
have a normally open, spring-loaded plunger type
back-up lamp switch (Fig. 2). The backup lamp
switch is located in a threaded hole on the side of the
manual transmission housing, beneath the floor
panel of the vehicle. The backup lamp switch has a
threaded body and a hex formation near the plunger
end of the switch, and an integral connector recepta-
cle at the opposite end of the switch. When installed,
only the connector receptacle and the hex formation
are visible on the outside of the transmission hous-
ing. Vehicles with an optional electronic automatic
transmission have a Transmission Range Sensor
(TRS) that is used to perform several functions,
including that of the backup lamp switch. The TRS is
described in further detail elsewhere in this service
information. The backup lamp switch cannot be
adjusted or repaired and, if faulty or damaged, the
entire switch unit must be replaced.
OPERATION
The backup lamp switch controls the flow of bat-
tery current to the backup lamp bulbs at the back of
the vehicle through an output on the back-up lamp
feed circuit. The switch plunger is mechanically actu-
ated by the gearshift mechanism within the trans-
mission, which will depress the switch plunger and
close the switch contacts whenever the reverse gear
has been selected. The switch receives battery cur-
rent through a fuse in the Junction Block (JB) on a
fused ignition switch output (run) circuit whenever
the ignition switch is in the On position. A take out
of the engine wire harness connects the backup lamp
switch to the vehicle electrical system. The backup
lamp switch and circuits can be tested using conven-
tional diagnostic tools and methods.
DIAGNOSIS AND TESTING - BACKUP LAMP
SWITCH
(1) Disconnect and isolate the battery negative
cable.
(2) Raise and support the vehicle.
(3) Locate and disconnect the engine wire harness
connector for the backup lamp switch from the
switch connector receptacle.
(4) Check for continuity between the two terminal
pins in the backup lamp switch connector receptacle.
(a) With the gear selector lever in the Reverse
position, there should be continuity.
(b) With the gear selector lever in any position
other than Reverse, there should be no continuity.
Fig. 2 Backup Lamp Switch - Typical
1 - MANUAL TRANSMISSION
2 - BACKUP LAMP SWITCH
3 - ENGINE WIRE HARNESS
KJLAMPS8Ls-15
LAMPS/LIGHTING - EXTERIOR (Continued)
Page 571 of 1803
REST-OF-WORLD
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the bulb and socket unit from the
license plate lamp unit housing that is being
removed. (Refer to 8 - ELECTRICAL/LAMPS/LIGHT-
ING - EXTERIOR/LICENSE PLATE LAMP BULB -
REMOVAL - REST-OF-WORLD).
(3) Remove the two screws that secure the license
plate lamp unit to the back of the license plate
bracket (Fig. 49).
(1) Remove the license plate lamp unit from the
back of the license plate bracket.
INSTALLATION
NORTH AMERICA
(1) Position the license plate lamp unit to the rear
bumper fascia.
(2) Reconnect the wire harness connector for the
license plate lamp unit to the lamp socket pigtail
wire.
(3) Position the license plate lamp unit into the
mounting hole in the rear bumper fascia (Fig. 48).
(4) Install and tighten the two screws that secure
the license plate lamp unit housing to the rear
bumper fascia. Tighten the screws to 2 N´m (20 in.
lbs.).
(5) Reconnect the battery negative cable.REST-OF-WORLD
(1) Position the license plate lamp unit onto the
back of the license plate bracket (Fig. 49).
(2) Install and tighten the two screws that secure
the license plate lamp unit to the back of the license
plate bracket. Tighten the screws to 2 N´m (20 in.
lbs.).
(3) Reinstall the bulb and socket unit into the
license plate lamp unit housing that is being
replaced. (Refer to 8 - ELECTRICAL/LAMPS/LIGHT-
ING - EXTERIOR/LICENSE PLATE LAMP BULB -
INSTALLATION - REST-OF-WORLD).
(4) Reconnect the battery negative cable.
MULTI-FUNCTION SWITCH
DESCRIPTION
The multi-function switch is located on the steering
column, just below the steering wheel (Fig. 50). The
only visible components of the multi-function switch
are two levers, or control stalks that extend through
dedicated openings in each side of the steering col-
umn shrouds. The remainder of the switch, its
mounting provisions, and its electrical connections
are all concealed beneath the steering column
shrouds. The switch housing and controls are con-
structed of molded black plastic. A saddle-like forma-
tion in the center of the multi-function switch
housing straddles the steering column tube just
below the column lock housing, and two posts inte-
gral to the lower surface of the switch housing
engage two holes on the forward-facing side of the
lock housing. Two integral ledge-like locating tabs
near the top of the rearward facing switch housing
surface are supported and located by two upright
stanchions that extend upward from the top of the
lock housing. Also on the rearward facing switch
housing surface near the center, an integral ledge-
like mounting tab rests on a similar ledge-like tab
that extends from each side of the steering column
lock housing. When the steering column shrouds are
installed on the column, the switch mounting tabs
are clamped along with the mounting tabs of the
clockspring between the integral mounting stan-
chions of the upper shroud and the lock housing tabs,
and are secured to the steering column lock housing
by the same two screws that secure the two shroud
halves to each other and the column.
There are several versions of the multi-function
switch to support both optional equipment and equip-
ment that is required only in certain markets. Each
multi-function switch control stalk has both white
nomenclature and International Control and Display
Symbol graphics applied to it, which clearly identify
its many functions. Each control stalk has a control
Fig. 49 License Plate Lamp Bulb Remove/Install -
Rest-Of-World
1 - LAMP UNIT (2)
2 - LICENSE PLATE BRACKET
3 - SCREW (4)
4 - BULB & SOCKET (2)
8Ls - 46 LAMPSKJ
LICENSE PLATE LAMP UNIT (Continued)
Page 1462 of 1803
DIAGNOSIS AND TESTING - TREAD WEAR
INDICATORS
Tread wear indicators are molded into the bottom
of the tread grooves. When tread depth is 1.6 mm
(1/16 in.), the tread wear indicators will appear as a
13 mm (1/2 in.) band (Fig. 14).
Tire replacement is necessary when indicators
appear in two or more grooves or if localized balding
occurs.
DIAGNOSIS AND TESTING - TIRE WEAR
PATTERNS
Under inflation will cause wear on the shoulders of
tire. Over inflation will cause wear at the center of
tire.
Excessive camber causes the tire to run at an
angle to the road. One side of tread is then worn
more than the other (Fig. 15).
Excessive toe-in or toe-out causes wear on the
tread edges and a feathered effect across the tread
(Fig. 15).
DIAGNOSIS AND TESTING - TIRE NOISE OR
VIBRATION
Radial-ply tires are sensitive to force impulses
caused by improper mounting, vibration, wheel
defects, or possibly tire imbalance.
To find out if tires are causing the noise or vibra-
tion, drive the vehicle over a smooth road at varyingspeeds. Note the noise level during acceleration,
deceleration and slight left and right steering inputs.
STANDARD PROCEDURE - REPAIRING LEAKS
For proper repairing, a radial tire must be removed
from the wheel. Repairs should only be made if the
defect, or puncture, is in the tread area (Fig. 16). The
tire should be replaced if the puncture is located in
the sidewall.
Deflate tire completely before removing the tire
from the wheel. Use lubrication such as a mild soap
solution when dismounting or mounting tire. Use
tools free of burrs or sharp edges which could dam-
age the tire or wheel rim.
Before mounting tire on wheel, make sure all rust
is removed from the rim bead and repaint if neces-
sary.
Install wheel on vehicle, and tighten to proper
torque specification.
CLEANING
Remove the protective coating on the tires before
delivery of a vehicle. This coating may cause deteri-
oration of the tires.
To remove the protective coating, apply warm
water and let it soak for a few minutes. Afterwards,
scrub the coating away with a soft bristle brush.
Steam cleaning may also be used to remove the coat-
ing.
NOTE: DO NOT use gasoline, mineral oil, oil-based
solvent or a wire brush for cleaning.
SPECIFICATIONS
SPECIFICATIONS
DESCRIPTION SPECIFICATION
Tire P215/75R16
Tire P235/70R16
Spare Tire P215/75D16
POLYSPARE ONLY ON
169
SPARE TIRE
REMOVAL
(1) Raise the license plate.
(2) Remove the two bolts securing the wheel cover
to the wheel.
(3) Remove the two lug nuts and the one wheel
lock (if equipped) securing the tire/wheel to the spare
tire carrier.
(4) Remove the spare tire.
Fig. 14 Tread Wear Indicators
1 - TREAD ACCEPTABLE
2 - TREAD UNACCEPTABLE
3 - WEAR INDICATOR
22 - 8 TIRES/WHEELSKJ
TIRES (Continued)
Page 1753 of 1803
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-68
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION........................9-26
INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION....................9-28,9-36
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.......................9-27,9-35
INTERIOR - DESCRIPTION, LAMPS/
LIGHTING..........................8L-65
INTERIOR - DIAGNOSIS AND TESTING,
LAMPS/LIGHTING....................8L-68
INTERIOR - OPERATION, LAMPS/
LIGHTING..........................8L-67
INTERIOR - SPECIFICATIONS,
LAMPS/LIGHTING....................8L-71
INTERLOCK CABLE - INSTALLATION,
PARK .............................21-153
INTERLOCK CABLE - REMOVAL, PARK . . . 21-153
INTERLOCK SYSTEM - DESCRIPTION,
BRAKE TRANSMISSION SHIFT.........21-124
INTERLOCK SYSTEM - DIAGNOSIS AND
TESTING, BRAKE TRANSMISSION
SHIFT.............................21-125
INTERLOCK SYSTEM - OPERATION,
BRAKE TRANSMISSION SHIFT.........21-125
INTERMEDIATE SHAFT - INSTALLATION . . . 19-11
INTERMEDIATE SHAFT - REMOVAL......19-11
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-4
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
INTRUSION TRANSCEIVER MODULE -
DESCRIPTION.......................8Q-14
INTRUSION TRANSCEIVER MODULE -
INSTALLATION......................8Q-16
INTRUSION TRANSCEIVER MODULE -
OPERATION.........................8Q-15
INTRUSION TRANSCEIVER MODULE -
REMOVAL..........................8Q-15
INVERTED FLARING - STANDARD
PROCEDURE, DOUBLE..................5-8
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - INSTALLATION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
IOD FUSE - REMOVAL..............8W-97-3
ISO FLARING - STANDARD PROCEDURE....5-8
JOINT - DESCRIPTION, UPPER
SUSPENSION ARM, BUSHINGS, AND
BALL...............................2-20
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - INSTALLATION, UPPER BALL.....2-20
JOINT - OPERATION, UPPER
SUSPENSION ARM, BUSHINGS, AND
BALL...............................2-20
JOINT - REMOVAL, UPPER BALL.........2-20
JOINT/BOOT-INNER - INSTALLATION, CV . . . 3-17
JOINT/BOOT-INNER - REMOVAL, CV.......3-15
JOINT/BOOT-OUTER - INSTALLATION, CV . . . 3-13
JOINT/BOOT-OUTER - REMOVAL, CV......3-12
JOINTS - ASSEMBLY, SINGLE CARDAN
UNIVERSAL...........................3-9
JOINTS - DISASSEMBLY, SINGLE
CARDAN UNIVERSAL...................3-8
JOUNCE BUMPER - INSTALLATION.......2-19
JOUNCE BUMPER - REMOVAL...........2-19
JUMP STARTING PROCEDURE -
STANDARD PROCEDURE
.................0-5
JUNCTION BLOCK - DESCRIPTION
.....8W-97-4
JUNCTION BLOCK - DESCRIPTION
........5-20
JUNCTION BLOCK - DIAGNOSIS AND
TESTING
.........................8W-97-4
JUNCTION BLOCK - INSTALLATION
.......5-20
JUNCTION BLOCK - OPERATION
......8W-97-4
JUNCTION BLOCK - OPERATION
..........5-20
JUNCTION BLOCK - REMOVAL
...........5-20
KEY - DESCRIPTION, TRANSPONDER
....8Q-18
KEY - OPERATION, TRANSPONDER
......8Q-18
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY
................8E-15
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-18
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-16KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY............................8E-17
KEY TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY........8Q-8
KEY-IN IGNITION SWITCH -
DESCRIPTION.......................19-10
KEY-IN IGNITION SWITCH - DIAGNOSIS
AND TESTING.......................19-10
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE................8N-7
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE................8N-7
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE...............8N-7
KEYLESS ENTRY MODULE - OPERATION,
REMOTE............................8N-7
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE............................8N-7
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING, REMOTE......8N-8
KEYLESS ENTRY TRANSMITTER -
SPECIFICATIONS, REMOTE..............8N-9
KNEE BLOCKER - INSTALLATION.......23-155
KNEE BLOCKER - REMOVAL...........23-155
KNOCK SENSOR - DESCRIPTION.........8I-11
KNOCK SENSOR - INSTALLATION........8I-12
KNOCK SENSOR - OPERATION..........8I-11
KNOCK SENSOR - REMOVAL............8I-12
KNUCKLE - INSTALLATION...............2-9
KNUCKLE - REMOVAL...................2-9
LABEL - DESCRIPTION, VEHICLE
EMISSION CONTROL INFORMATION
(VECI)............................Intro.-8
LABEL - DESCRIPTION, VEHICLE SAFETY
CERTIFICATION.....................Intro.-9
LACE - INSTALLATION, OPENING TRIM . . 23-180
LACE - REMOVAL, OPENING TRIM......23-180
LAMP BULB - INSTALLATION, ASH
RECEIVER..........................8L-71
LAMP BULB - INSTALLATION, CARGO....8L-73
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP BULB - INSTALLATION,
COURTESY.........................8L-76
LAMP BULB - INSTALLATION, FRONT....8L-27
LAMP BULB - INSTALLATION, FRONT
FOG ...............................8L-22
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-28
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-45
LAMP BULB - INSTALLATION, READING . . . 8L-79
LAMP BULB - INSTALLATION, REAR.....8L-59
LAMP BULB - INSTALLATION, REPEATER . . 8L-60
LAMP BULB - INSTALLATION, VANITY....8L-84
LAMP BULB - REMOVAL, ASH RECEIVER . . 8L-71
LAMP BULB - REMOVAL, CARGO........8L-72
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-18
LAMP BULB - REMOVAL, COURTESY.....8L-75
LAMP BULB - REMOVAL, FRONT........8L-26
LAMP BULB - REMOVAL, FRONT FOG....8L-21
LAMP BULB - REMOVAL, FRONT
POSITION..........................8L-28
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-44
LAMP BULB - REMOVAL, READING......8L-79
LAMP BULB - REMOVAL, REAR.........8L-58
LAMP BULB - REMOVAL, REPEATER.....8L-60
LAMP BULB - REMOVAL, VANITY........8L-83
LAMP INDICATOR - DESCRIPTION,
FRONT FOG.........................8J-19
LAMP INDICATOR - DESCRIPTION, REAR
FOG ...............................8J-27
LAMP INDICATOR - OPERATION, FRONT
FOG ...............................8J-19
LAMP INDICATOR - OPERATION, REAR
FOG ...............................8J-27
LAMP (MIL) - DESCRIPTION,
MALFUNCTION INDICATOR.............8J-24
LAMP (MIL) - OPERATION,
MALFUNCTION INDICATOR
.............8J-24
LAMP RELAY - DESCRIPTION, DAYTIME
RUNNING
...........................8L-20
LAMP RELAY - DESCRIPTION, FRONT
FOG
...............................8L-22
LAMP RELAY - DESCRIPTION, PARK
.....8L-54
LAMP RELAY - DESCRIPTION, REAR FOG
. 8L-56LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT FOG.................8L-23
LAMP RELAY - DIAGNOSIS AND
TESTING, PARK......................8L-55
LAMP RELAY - DIAGNOSIS AND
TESTING, REAR FOG..................8L-57
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - INSTALLATION, FRONT
FOG ...............................8L-24
LAMP RELAY - INSTALLATION, PARK.....8L-56
LAMP RELAY - INSTALLATION, REAR
FOG ...............................8L-58
LAMP RELAY - OPERATION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - OPERATION, FRONT FOG . . 8L-22
LAMP RELAY - OPERATION, PARK.......8L-54
LAMP RELAY - OPERATION, REAR FOG . . . 8L-57
LAMP RELAY - REMOVAL, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - REMOVAL, FRONT FOG . . . 8L-24
LAMP RELAY - REMOVAL, PARK........8L-55
LAMP RELAY - REMOVAL, REAR FOG....8L-58
LAMP REPLACEMENT - STANDARD
PROCEDURE, CMTC...................8M-2
LAMP REPLACEMENT - STANDARD
PROCEDURE, COURTESY...............8M-2
LAMP SWITCH - DESCRIPTION, BACKUP . . 8L-15
LAMP SWITCH - DESCRIPTION, BRAKE . . . 8L-16
LAMP SWITCH - DIAGNOSIS AND
TESTING, BACKUP.....................8L-15
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE.....................8L-17
LAMP SWITCH - INSTALLATION, BRAKE . . 8L-18
LAMP SWITCH - INSTALLATION, CARGO . . 8L-74
LAMP SWITCH - INSTALLATION,
READING...........................8L-80
LAMP SWITCH - OPERATION, BACKUP . . . 8L-15
LAMP SWITCH - OPERATION, BRAKE.....8L-16
LAMP SWITCH - REMOVAL, BRAKE......8L-17
LAMP SWITCH - REMOVAL, CARGO......8L-73
LAMP SWITCH - REMOVAL, READING....8L-80
LAMP UNIT - ADJUSTMENT, FRONT FOG . . 8L-25
LAMP UNIT - INSTALLATION, ASH
RECEIVER..........................8L-72
LAMP UNIT - INSTALLATION, CARGO.....8L-74
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP UNIT - INSTALLATION, COURTESY . . 8L-77
LAMP UNIT - INSTALLATION, FRONT.....8L-28
LAMP UNIT - INSTALLATION, FRONT
FOG ...............................8L-25
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-46
LAMP UNIT - INSTALLATION, READING . . . 8L-81
LAMP UNIT - INSTALLATION, REAR......8L-60
LAMP UNIT - INSTALLATION, REPEATER . . 8L-61
LAMP UNIT - REMOVAL, ASH RECEIVER . . 8L-72
LAMP UNIT - REMOVAL, CARGO........8L-74
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-19
LAMP UNIT - REMOVAL, COURTESY.....8L-76
LAMP UNIT - REMOVAL, FRONT.........8L-27
LAMP UNIT - REMOVAL, FRONT FOG.....8L-25
LAMP UNIT - REMOVAL, LICENSE PLATE . . 8L-45
LAMP UNIT - REMOVAL, READING.......8L-81
LAMP UNIT - REMOVAL, REAR..........8L-59
LAMP UNIT - REMOVAL, REPEATER......8L-60
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
DIAGNOSIS AND TESTING..............8L-7
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-5
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS.....................8L-15
LAMPS/LIGHTING - INTERIOR -
DESCRIPTION.......................8L-65
LAMPS/LIGHTING - INTERIOR -
DIAGNOSIS AND TESTING.............8L-68
LAMPS/LIGHTING - INTERIOR -
OPERATION
.........................8L-67
LAMPS/LIGHTING - INTERIOR -
SPECIFICATIONS
.....................8L-71
LASH ADJUSTER - DIAGNOSIS AND
TESTING, HYDRAULIC
..............9-19,9-30
LATCH - ACCESS PANEL - DESCRIPTION
. 23-139
LATCH - ACCESS PANEL - INSTALLATION
. 23-139
14 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1754 of 1803
LATCH - ACCESS PANEL - REMOVAL....23-139
LATCH - INSTALLATION . . 23-120,23-124,23-131,
23-137
LATCH - INSTALLATION, FLIP-UP GLASS . 23-136
LATCH - INSTALLATION, FLOOR
CONSOLE LID......................23-158
LATCH - INSTALLATION, GLOVE BOX....23-148
LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT BACK...........23-170
LATCH / LOCK - REMOVAL, FOLDING
REAR SEAT BACK...................23-170
LATCH - REMOVAL......23-120,23-124,23-131,
23-137
LATCH - REMOVAL, FLIP-UP GLASS.....23-136
LATCH - REMOVAL, FLOOR CONSOLE
LID...............................23-158
LATCH - REMOVAL, GLOVE BOX........23-148
LATCH RELEASE CABLE - INSTALLATION . 23-120
LATCH RELEASE CABLE - REMOVAL....23-120
LATCH RELEASE HANDLE -
INSTALLATION......................23-120
LATCH RELEASE HANDLE - REMOVAL . . . 23-120
LATCH STRIKER - INSTALLATION......23-124,
23-132,23-137
LATCH STRIKER - INSTALLATION, GLOVE
BOX ..............................23-149
LATCH STRIKER - INSTALLATION, REAR
SEAT BACK........................23-171
LATCH STRIKER - REMOVAL....23-124,23-132,
23-137
LATCH STRIKER - REMOVAL, GLOVE
BOX ..............................23-148
LATCH STRIKER - REMOVAL, REAR
SEAT BACK........................23-170
LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING FLUID...........21-80
LEAK - DIAGNOSIS AND TESTING,
ENGINE OIL..........................9-60
LEAK DETECTION PUMP - DESCRIPTION . . 25-27
LEAK DETECTION PUMP - INSTALLATION . 25-28
LEAK DETECTION PUMP - OPERATION....25-28
LEAK DETECTION PUMP - REMOVAL.....25-28
LEAK DOWN TEST - DIAGNOSIS AND
TESTING, FUEL PRESSURE..............14-3
LEAKAGE - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE.......9-8
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-4
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-68
LEAKS - DIAGNOSIS AND TESTING,
REAR SEAL AREA.....................9-61
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-2
LEAKS - STANDARD PROCEDURE,
REPAIRING..........................22-8
LEARN - STANDARD PROCEDURE, TCM
QUICK.............................8E-21
LEFT POWER SEAT SWITCH -
DESCRIPTION.......................8N-16
LEFT POWER SEAT SWITCH -
DIAGNOSIS AND TESTING.............8N-17
LEFT POWER SEAT SWITCH -
INSTALLATION......................8N-18
LEFT POWER SEAT SWITCH -
OPERATION
.........................8N-17
LEFT POWER SEAT SWITCH - REMOVAL
. . 8N-18
LEFT SIDE - INSTALLATION
.........2-12,2-15
LEFT SIDE - REMOVAL
.............2-11,2-15
LEVEL - DIAGNOSIS AND TESTING,
EFFECTS OF INCORRECT FLUID
........21-125
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-54
LEVEL - STANDARD PROCEDURES,
MASTER CYLINDER FLUID
..............5-26
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
.................21-126
LEVEL SENDING UNIT - DIAGNOSIS AND
TESTING, FUEL
.......................14-9
LEVEL SENDING UNIT / SENSOR -
DESCRIPTION, FUEL
...................14-9
LEVEL SENDING UNIT / SENSOR -
INSTALLATION, FUEL
.................14-10
LEVEL SENDING UNIT / SENSOR -
OPERATION, FUEL
.....................14-9
LEVEL SENDING UNIT / SENSOR -
REMOVAL, FUEL
......................14-9LEVEL SWITCH - DESCRIPTION,
WASHER FLUID.....................8R-17
LEVEL SWITCH - INSTALLATION,
WASHER FLUID.....................8R-18
LEVEL SWITCH - OPERATION, WASHER
FLUID.............................8R-17
LEVEL SWITCH - REMOVAL, WASHER
FLUID.............................8R-17
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP.........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LEVER - INSTALLATION................5-31
LEVER - INSTALLATION, SHIFT . . . 21-214,21-249
LEVER - REMOVAL....................5-31
LEVER - REMOVAL, SHIFT......21-213,21-248
LHD - INSTALLATION...............8W-97-6
LHD - REMOVAL....................8W-97-5
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LID LATCH - INSTALLATION, FLOOR
CONSOLE..........................23-158
LID LATCH - REMOVAL, FLOOR
CONSOLE..........................23-158
LIGHTER OUTLET - DESCRIPTION,
CIGAR...........................8W-97-2
LIGHTER OUTLET - DIAGNOSIS AND
TESTING, CIGAR...................8W-97-2
LIGHTER OUTLET - OPERATION, CIGAR . 8W-97-2
LIMITS - DESCRIPTION, HIGH AND LOW . . 25-20
LINE - DESCRIPTION, REFRIGERANT.....24-38
LINE - INSTALLATION, A/C DISCHARGE . . . 24-47
LINE - INSTALLATION, A/C LIQUID.......24-47
LINE - INSTALLATION, A/C SUCTION.....24-49
LINE - REMOVAL, A/C DISCHARGE.......24-46
LINE - REMOVAL, A/C LIQUID...........24-47
LINE - REMOVAL, A/C SUCTION.........24-48
LINE AND HOSES - DIAGNOSIS AND
TESTING, BRAKE.......................5-8
LINE PRESSURE (LP) SENSOR -
DESCRIPTION......................21-144
LINE PRESSURE (LP) SENSOR -
INSTALLATION......................21-144
LINE PRESSURE (LP) SENSOR -
OPERATION........................21-144
LINE PRESSURE (LP) SENSOR -
REMOVAL.........................21-144
LINES - DESCRIPTION, BRAKE............5-8
LINES - DESCRIPTION, FUEL...........14-10
LINES - DESCRIPTION, VACUUM........25-33
LINK - INSTALLATION, STABILIZER.......2-14
LINK - REMOVAL, STABILIZER...........2-14
LINK CONNECTOR - DESCRIPTION, DATA . 8E-10
LINK CONNECTOR - OPERATION, DATA . . . 8E-10
LINKAGE - INSTALLATION................6-9
LINKAGE - REMOVAL...................6-8
LINKAGE - STANDARD PROCEDURE,
STEERING..........................19-16
LIQUID LINE - INSTALLATION, A/C.......24-47
LIQUID LINE - REMOVAL, A/C...........24-47
LOAD TEST - STANDARD PROCEDURE....8F-12
LOAD VALUE - DESCRIPTION
...........25-20
LOADS - STANDARD PROCEDURE,
TESTING FOR A SHORT TO GROUND
ON FUSES POWERING SEVERAL
......8W-01-9
LOCATION - DESCRIPTION, CONNECTOR/
GROUND/SPLICE
...................8W-91-1
LOCATIONS - DESCRIPTION, FLUID
FILL/CHECK
...........................0-4
LOCATIONS - SPECIFICATIONS, SEALER
. . 23-87LOCATIONS - SPECIFICATIONS, WELD
AND STRUCTURAL ADHESIVE...........23-9
LOCK - INSTALLATION, FOLDING REAR
SEAT BACK LATCH..................23-170
LOCK - REMOVAL, FOLDING REAR SEAT
BACK LATCH.......................23-170
LOCK / UNLOCK SWITCH -
INSTALLATION, DOOR.................8N-5
LOCK / UNLOCK SWITCH - REMOVAL,
DOOR..............................8N-4
LOCK CYLINDER - INSTALLATION......23-125,
23-138
LOCK CYLINDER - INSTALLATION.......19-11
LOCK CYLINDER - REMOVAL....23-125,23-137
LOCK CYLINDER - REMOVAL...........19-10
LOCK MOTOR - DESCRIPTION, DOOR.....8N-5
LOCK MOTOR - DIAGNOSIS AND
TESTING, DOOR......................8N-5
LOCK MOTOR - OPERATION, DOOR.......8N-5
LOCK OUT - ADJUSTMENT..............5-30
LOCK RELAY - DESCRIPTION, DOOR......8N-6
LOCK RELAY - DIAGNOSIS AND
TESTING, DOOR......................8N-6
LOCK RELAY - INSTALLATION, DOOR.....8N-7
LOCK RELAY - OPERATION, DOOR........8N-6
LOCK RELAY - REMOVAL, DOOR.........8N-6
LOCK SWITCH - DESCRIPTION, DOOR
CYLINDER...........................8Q-9
LOCK SWITCH - DESCRIPTION,
TAILGATE CYLINDER...................8N-9
LOCK SWITCH - DIAGNOSIS AND
TESTING, DOOR CYLINDER............8Q-10
LOCK SWITCH - DIAGNOSIS AND
TESTING, TAILGATE CYLINDER..........8N-9
LOCK SWITCH - INSTALLATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - INSTALLATION,
TAILGATE CYLINDER..................8N-10
LOCK SWITCH - OPERATION, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - OPERATION, TAILGATE
CYLINDER...........................8N-9
LOCK SWITCH - REMOVAL, DOOR
CYLINDER..........................8Q-10
LOCK SWITCH - REMOVAL, TAILGATE
CYLINDER..........................8N-10
LOCKS - DESCRIPTION, POWER.........8N-1
LOCKS - DIAGNOSIS AND TESTING,
POWER.............................8N-3
LOCKS - OPERATION, POWER...........8N-3
LOCK/UNLOCK SWITCH - DIAGNOSIS
AND TESTING, DOOR..................8N-4
LOOP ADJUSTER - INSTALLATION, SEAT
BELT TURNING......................8O-38
LOOP ADJUSTER - REMOVAL, SEAT
BELT TURNING......................8O-37
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP
.........................8L-40
LOW FUEL INDICATOR - DESCRIPTION
. . . 8J-22
LOW FUEL INDICATOR - OPERATION
.....8J-22
LOW INDICATOR - DESCRIPTION,
COOLANT
...........................8J-15
LOW INDICATOR - OPERATION,
COOLANT
...........................8J-16
LOW LIMITS - DESCRIPTION, HIGH
......25-20
LOW MODE INDICATOR - DESCRIPTION,
FOUR
..............................8J-29
LOW MODE INDICATOR - OPERATION,
FOUR
..............................8J-30
LOW OIL PRESSURE INDICATOR -
DESCRIPTION
.......................8J-23
LOW OIL PRESSURE INDICATOR -
OPERATION
.........................8J-23
LOW PRESSURE SWITCH -
DESCRIPTION, A/C
...................24-18
LOW PRESSURE SWITCH - DIAGNOSIS
AND TESTING, A/C
...................24-19
LOW PRESSURE SWITCH -
INSTALLATION, A/C
...................24-19
KJINDEX 15
Description Group-Page Description Group-Page Description Group-Page
Page 1757 of 1803
OPERATION - DESCRIPTION, MODES OF . . 8E-11
OPERATION - DIAGNOSIS AND TESTING,
AIR CHECKING TRANSMISSION
CLUTCH............................21-80
ORDER, 2.4L 4-CYLINDER - ENGINE
FIRING..............................8I-2
ORDER, 3.7L V-6 - ENGINE FIRING........8I-2
ORIFICE TUBE - DESCRIPTION, A/C......24-50
ORIFICE TUBE - INSTALLATION, A/C......24-50
ORIFICE TUBE - OPERATION, A/C........24-50
ORIFICE TUBE - REMOVAL, A/C.........24-50
ORVR - DESCRIPTION.................25-29
ORVR - OPERATION..................25-29
OUT - ADJUSTMENT, LOCK..............5-30
OUTBOARD SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-34
OUTBOARD SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-33
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-186
OUTER BELT MOLDING - INSTALLATION,
REAR DOOR.......................23-186
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-186
OUTER BELT MOLDING - REMOVAL,
REAR DOOR.......................23-186
OUTER TIE ROD END REMOVAL TOOL,
SPECIAL TOOLS.....................19-15
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-11
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER.........................8W-97-11
OUTLET - INSTALLATION, POWER....8W-97-13
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER......8W-97-11
OUTLET - REMOVAL, POWER........8W-97-12
OUTLET BARRELS - INSTALLATION,
PANEL.............................24-29
OUTLET BARRELS - REMOVAL, PANEL . . . 24-29
OUTLETS - DESCRIPTION, DEMISTER....24-29
OUTPUT - DESCRIPTION, PCM...........8I-4
OUTPUT - OPERATION, PCM............14-33
OUTPUT - OPERATION, PCM.............8I-4
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - INSTALLATION,
REAR.............................21-212
OUTPUT SHAFT SEAL - REMOVAL,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - REMOVAL, REAR . 21-210
OUTPUT SPEED SENSOR - DESCRIPTION . 21-152
OUTPUT SPEED SENSOR -
INSTALLATION......................21-152
OUTPUT SPEED SENSOR - OPERATION . . 21-152
OUTPUT SPEED SENSOR - REMOVAL . . . 21-152
OVERDRIVE OFF INDICATOR -
DESCRIPTION.......................8J-26
OVERDRIVE OFF INDICATOR -
OPERATION.........................8J-26
OVERDRIVE SWITCH - DESCRIPTION....21-153
OVERDRIVE SWITCH - OPERATION.....21-153
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE, REMOVAL........8M-4
OVERRIDE RELAY - DESCRIPTION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - INSTALLATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - OPERATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - REMOVAL, CLUTCH
SWITCH.............................6-10
OXYGEN SENSOR - DESCRIPTION.......14-40
OXYGEN SENSOR - INSTALLATION.......14-43
OXYGEN SENSOR - OPERATION.........14-40
OXYGEN SENSOR - REMOVAL..........14-41
PADS - INSTALLATION, FRONT BRAKE.....5-11
PADS - REMOVAL, FRONT BRAKE........5-11
PAINT CODE - DESCRIPTION..........23-162
PAINT CODES - SPECIFICATIONS.......23-162
PAINT TOUCH-UP - DESCRIPTION
......23-163
PAN - CLEANING, OIL
..................9-63
PAN - DESCRIPTION, OIL
...............9-63
PAN - INSPECTION, OIL
................9-63
PAN - INSTALLATION, OIL
...............9-64PAN - REMOVAL, OIL..................9-63
PANEL - DESCRIPTION, LATCH - ACCESS . 23-139
PANEL - INSTALLATION, GLASS........23-178
PANEL - INSTALLATION, LATCH -
ACCESS...........................23-139
PANEL - INSTALLATION, QUARTER TRIM . 23-159
PANEL - INSTALLATION, TRIM . . . 23-126,23-132,
23-138
PANEL - REMOVAL, GLASS............23-178
PANEL - REMOVAL, LATCH - ACCESS . . . 23-139
PANEL - REMOVAL, QUARTER TRIM....23-159
PANEL - REMOVAL, TRIM . 23-125,23-132,23-138
PANEL ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS...................23-178
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-8
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT......................23-151
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT......................23-149
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT......................23-154
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT......................23-154
PANEL DOOR - INSTALLATION..........24-36
PANEL DOOR ACTUATOR -
INSTALLATION.......................24-25
PANEL DOOR ACTUATOR - REMOVAL....24-24
PANEL DRIVER SIDE BEZELS -
INSTALLATION, INSTRUMENT..........23-154
PANEL DRIVER SIDE BEZELS -
REMOVAL, INSTRUMENT.............23-153
PANEL END CAP - INSTALLATION,
INSTRUMENT......................23-153
PANEL END CAP - REMOVAL,
INSTRUMENT......................23-153
PANEL OUTLET BARRELS -
INSTALLATION.......................24-29
PANEL OUTLET BARRELS - REMOVAL....24-29
PANEL PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT..........23-154
PANEL PASSENGER SIDE BEZEL -
REMOVAL, INSTRUMENT.............23-154
PANEL SEAL - INSTALLATION, GLASS . . . 23-178
PANEL SEAL - REMOVAL, GLASS.......23-178
PANEL TOP COVER - INSTALLATION,
INSTRUMENT......................23-153
PANEL TOP COVER - REMOVAL,
INSTRUMENT......................23-152
PARK - INTERLOCK CABLE -
INSTALLATION......................21-153
PARK - INTERLOCK CABLE - REMOVAL . . 21-153
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PARK RAMP - INSTALLATION, WIPER
ARM ..............................8R-43
PARK RAMP - REMOVAL, WIPER ARM . . . 8R-43
PARKING BRAKE - DESCRIPTION.........5-29
PARKING BRAKE - OPERATION...........5-29
PARK-INTERLOCK CABLE -
ADJUSTMENTS.....................21-154
PART TIME INDICATOR - DESCRIPTION . . . 8J-29
PART TIME INDICATOR - OPERATION.....8J-29
PASSENGER AIRBAG - DESCRIPTION....8O-27
PASSENGER AIRBAG - INSTALLATION....8O-29
PASSENGER AIRBAG - OPERATION......8O-27
PASSENGER AIRBAG - REMOVAL........8O-28
PASSENGER AIRBAG DOOR -
INSTALLATION......................8O-30
PASSENGER AIRBAG DOOR - REMOVAL . . 8O-29
PASSENGER AIRBAG MOUNTING
BRACKET - INSTALLATION.............8O-31
PASSENGER AIRBAG MOUNTING
BRACKET - REMOVAL
.................8O-31
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION
.......................8G-14
PASSENGER SEAT HEATER SWITCH -
INSTALLATION
......................8G-15
PASSENGER SEAT HEATER SWITCH -
OPERATION
.........................8G-14
PASSENGER SEAT HEATER SWITCH -
REMOVAL
..........................8G-15PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT PANEL....23-154
PASSENGER SIDE BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION..................8E-11
PCM - OPERATION...................8E-14
PCM INPUT - OPERATION, ASD SENSE.....8I-4
PCM OUTPUT - DESCRIPTION............8I-4
PCM OUTPUT - OPERATION............14-33
PCM OUTPUT - OPERATION.............8I-4
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE.........................8E-1
PCV VALVE - DESCRIPTION............25-29
PCV VALVE - DIAGNOSIS AND TESTING . . . 25-31
PCV VALVE - INSTALLATION............25-32
PCV VALVE - OPERATION..............25-31
PCV VALVE - REMOVAL...............25-32
PEDAL - DESCRIPTION.................5-20
PEDAL - INSTALLATION................5-20
PEDAL - INSTALLATION, ACCELERATOR . . . 14-30
PEDAL - INSTALLATION, CLUTCH.........6-10
PEDAL - OPERATION...................5-20
PEDAL - REMOVAL....................5-20
PEDAL - REMOVAL, ACCELERATOR......14-29
PEDAL - REMOVAL, CLUTCH............6-10
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-11
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-11
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-11
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION..........6-8
PILOT BEARING - REMOVAL..............6-8
PINION GEAR/RING GEAR -
INSTALLATION........................3-46
PINION GEAR/RING GEAR - REMOVAL.....3-44
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION...................3-112,3-82
PINION GEAR/RING GEAR/TONE RING -
REMOVAL......................3-110,3-79
PINION SEAL - INSTALLATION . . 3-103,3-39,3-68
PINION SEAL - REMOVAL......3-102,3-38,3-68
PIPE - INSTALLATION, CROSS-OVER......11-3
PIPE - REMOVAL, CROSS-OVER..........11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-49
PISTON FITTING - STANDARD
PROCEDURE.........................9-50
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-52
PISTONS - DESCRIPTION.............21-155
PISTONS - OPERATION...............21-155
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-160
PLANETARY GEARTRAIN - CLEANING....21-159
PLANETARY GEARTRAIN - DESCRIPTION . 21-157
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-159
PLANETARY GEARTRAIN - INSPECTION . . 21-159
PLANETARY GEARTRAIN - OPERATION . . 21-157
PLATE - INSTALLATION, DOOR SILL
SCUFF............................23-157
PLATE - INSTALLATION, FLEX............9-49
PLATE - INSTALLATION, FRONT SKID......13-6
PLATE - INSTALLATION, FUEL TANK
SKID...............................13-9
PLATE - INSTALLATION, REAR DOOR
SCUFF............................23-160
PLATE - INSTALLATION, TRANSFER
CASE SKID..........................13-7
PLATE - REMOVAL, DOOR SILL SCUFF . . . 23-157
PLATE - REMOVAL, FLEX...............9-49
PLATE - REMOVAL, FRONT SKID.........13-6
PLATE - REMOVAL, FUEL TANK SKID
......13-9
PLATE - REMOVAL, REAR DOOR SCUFF
. . 23-160
PLATE - REMOVAL, TRANSFER CASE
SKID
...............................13-7
PLATE LAMP BULB - INSTALLATION,
LICENSE
...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE
...........................8L-44
18 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1773 of 1803
INSTALLATION, DAYTIME RUNNING
LAMP RELAY........................8L-21
INSTALLATION, ENGINE ASSEMBLY.......9-12
INSTALLATION, ENGINE COOLANT
TEMPERATURE SENSOR................7-22
INSTALLATION, EXHAUST MANIFOLD......9-53
INSTALLATION, FRONT FOG LAMP BULB . . 8L-22
INSTALLATION, FRONT FOG LAMP
RELAY.............................8L-24
INSTALLATION, FRONT FOG LAMP UNIT . . 8L-25
INSTALLATION, FRONT LAMP BULB......8L-27
INSTALLATION, FRONT LAMP UNIT......8L-28
INSTALLATION, FRONT MOUNT..........9-44
INSTALLATION, FRONT POSITION LAMP
BULB..............................8L-28
INSTALLATION, HAZARD SWITCH........8L-30
INSTALLATION, HEADLAMP BULB.......8L-32
INSTALLATION, HEADLAMP HIGH BEAM
RELAY.............................8L-35
INSTALLATION, HEADLAMP LEVELING
MOTOR............................8L-36
INSTALLATION, HEADLAMP LEVELING
SWITCH............................8L-38
INSTALLATION, HEADLAMP LOW BEAM
RELAY.............................8L-41
INSTALLATION, HEADLAMP UNIT........8L-42
INSTALLATION, HYDRAULIC LIFTERS......9-29
INSTALLATION, INTAKE MANIFOLD........9-52
INSTALLATION, LAMP.................8L-66
INSTALLATION, LAMP BAR.............8L-66
INSTALLATION, LAMP BAR SWITCH......8L-67
INSTALLATION, LICENSE PLATE LAMP
BULB..............................8L-45
INSTALLATION, LICENSE PLATE LAMP
UNIT..............................8L-46
INSTALLATION, LOWER BALL JOINT.......2-5
INSTALLATION, LOWER CONTROL ARM
BUSHING.............................2-3
INSTALLATION, LOWER SUSPENSION
ARM BUSHING........................2-8
INSTALLATION, MUFFLER...............11-5
INSTALLATION, MULTI-FUNCTION
SWITCH............................8L-53
INSTALLATION, OIL FILTER..............9-47
INSTALLATION, OIL PAN................9-48
INSTALLATION, OIL PUMP..............9-50
INSTALLATION, PARK LAMP RELAY......8L-56
INSTALLATION, PISTON & CONNECTING
ROD................................9-41
INSTALLATION, RADIATOR..............7-24
INSTALLATION, RADIATOR FAN -
ELECTRIC...........................7-27
INSTALLATION, REAR FOG LAMP RELAY . . 8L-58
INSTALLATION, REAR LAMP BULB.......8L-59
INSTALLATION, REAR LAMP UNIT.......8L-60
INSTALLATION, REAR MOUNT...........9-45
INSTALLATION, REPEATER LAMP BULB . . . 8L-60
INSTALLATION, REPEATER LAMP UNIT . . . 8L-61
INSTALLATION, RHD....................5-1
INSTALLATION, ROCKER ARMS..........9-30
INSTALLATION, STRUCTURAL COLLAR....9-44
INSTALLATION, TIMING BELT............9-56
INSTALLATION, TIMING BELT COVER(S) . . . 9-53
INSTALLATION, TIMING BELT
TENSIONER & PULLEY.................9-59
INSTALLATION, TRAILER TOW
CONNECTOR........................8L-61
INSTALLATION, TRAILER TOW RELAY....8L-63
INSTALLATION, UPPER BALL JOINT........2-6
INSTALLATION, UPPER CONTROL ARM
BUSHINGS............................2-4
INSTALLATION, UPPER SUSPENSION
ARM BUSHING........................2-8
INSTALLATION, VIBRATION DAMPER......9-43
INTAKE MANIFOLD - DESCRIPTION.......9-51
INTAKE MANIFOLD - INSPECTION........9-52
INTAKE MANIFOLD - INSTALLATION.......9-52
INTAKE MANIFOLD - OPERATION.........9-51
INTAKE MANIFOLD - REMOVAL..........9-52
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING........................9-51
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
...........................9-27
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
........................9-27
JOINT - INSTALLATION, LOWER BALL
......2-5
JOINT - INSTALLATION, UPPER BALL
......2-6
JOINT - REMOVAL, LOWER BALL
..........2-5JOINT - REMOVAL, UPPER BALL..........2-6
LAMP - INSTALLATION................8L-66
LAMP - REMOVAL....................8L-66
LAMP BAR - DESCRIPTION.............8L-65
LAMP BAR - DIAGNOSIS AND TESTING . . . 8L-65
LAMP BAR - INSTALLATION............8L-66
LAMP BAR - OPERATION..............8L-65
LAMP BAR - REMOVAL................8L-65
LAMP BAR AIMING - STANDARD
PROCEDURE........................8L-65
LAMP BAR SWITCH - DESCRIPTION.....8L-67
LAMP BAR SWITCH - INSTALLATION.....8L-67
LAMP BAR SWITCH - REMOVAL.........8L-67
LAMP BULB - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP BULB - INSTALLATION, FRONT....8L-27
LAMP BULB - INSTALLATION, FRONT
FOG ...............................8L-22
LAMP BULB - INSTALLATION, FRONT
POSITION..........................8L-28
LAMP BULB - INSTALLATION, LICENSE
PLATE .............................8L-45
LAMP BULB - INSTALLATION, REAR.....8L-59
LAMP BULB - INSTALLATION, REPEATER . . 8L-60
LAMP BULB - REMOVAL, CENTER HIGH
MOUNTED STOP.....................8L-18
LAMP BULB - REMOVAL, FRONT........8L-27
LAMP BULB - REMOVAL, FRONT FOG....8L-21
LAMP BULB - REMOVAL, FRONT
POSITION..........................8L-28
LAMP BULB - REMOVAL, LICENSE
PLATE .............................8L-44
LAMP BULB - REMOVAL, REAR.........8L-59
LAMP BULB - REMOVAL, REPEATER.....8L-60
LAMP RELAY - DESCRIPTION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - DESCRIPTION, FRONT
FOG ...............................8L-22
LAMP RELAY - DESCRIPTION, PARK.....8L-54
LAMP RELAY - DESCRIPTION, REAR FOG . 8L-56
LAMP RELAY - DIAGNOSIS AND
TESTING, FRONT FOG.................8L-23
LAMP RELAY - DIAGNOSIS AND
TESTING, PARK......................8L-55
LAMP RELAY - DIAGNOSIS AND
TESTING, REAR FOG..................8L-57
LAMP RELAY - INSTALLATION, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - INSTALLATION, FRONT
FOG ...............................8L-24
LAMP RELAY - INSTALLATION, PARK.....8L-56
LAMP RELAY - INSTALLATION, REAR
FOG ...............................8L-58
LAMP RELAY - OPERATION, DAYTIME
RUNNING...........................8L-20
LAMP RELAY - OPERATION, FRONT FOG . . 8L-22
LAMP RELAY - OPERATION, PARK.......8L-54
LAMP RELAY - OPERATION, REAR FOG . . . 8L-57
LAMP RELAY - REMOVAL, DAYTIME
RUNNING...........................8L-21
LAMP RELAY - REMOVAL, FRONT FOG . . . 8L-24
LAMP RELAY - REMOVAL, PARK........8L-55
LAMP RELAY - REMOVAL, REAR FOG....8L-58
LAMP SWITCH - DESCRIPTION, BACKUP . . 8L-15
LAMP SWITCH - DESCRIPTION, BRAKE . . . 8L-16
LAMP SWITCH - DIAGNOSIS AND
TESTING, BACKUP....................8L-15
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE.....................8L-17
LAMP SWITCH - INSTALLATION, BRAKE . . 8L-18
LAMP SWITCH - OPERATION, BACKUP . . . 8L-15
LAMP SWITCH - OPERATION, BRAKE.....8L-16
LAMP SWITCH - REMOVAL, BRAKE......8L-17
LAMP UNIT - ADJUSTMENT, FRONT FOG . . 8L-25
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP................8L-19
LAMP UNIT - INSTALLATION, FRONT.....8L-28
LAMP UNIT - INSTALLATION, FRONT
FOG ...............................8L-25
LAMP UNIT - INSTALLATION, LICENSE
PLATE .............................8L-46
LAMP UNIT - INSTALLATION, REAR......8L-60
LAMP UNIT - INSTALLATION, REPEATER
. . 8L-61
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP
.....................8L-19
LAMP UNIT - REMOVAL, FRONT
.........8L-27
LAMP UNIT - REMOVAL, FRONT FOG
.....8L-24
LAMP UNIT - REMOVAL, LICENSE PLATE
. . 8L-45LAMP UNIT - REMOVAL, REAR..........8L-59
LAMP UNIT - REMOVAL, REPEATER......8L-61
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
DIAGNOSIS AND TESTING..............8L-7
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-5
LAMPS/LIGHTING - EXTERIOR -
SPECIFICATIONS.....................8L-15
LASH ADJUSTER (TAPPET) NOISE
DIAGNOSIS - DIAGNOSIS AND
TESTING............................9-28
LEAK INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL...................9-4
LEAKAGE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION
PRESSURE...........................9-3
LEAKS - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-2
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD....................9-51
LEVEL CHECK, STANDARD PROCEDURE
- ENGINE OIL........................9-47
LEVELING MOTOR - DESCRIPTION,
HEADLAMP.........................8L-35
LEVELING MOTOR - INSTALLATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - OPERATION,
HEADLAMP.........................8L-36
LEVELING MOTOR - REMOVAL,
HEADLAMP.........................8L-36
LEVELING SWITCH - DESCRIPTION,
HEADLAMP...........................8L-37
LEVELING SWITCH - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-37
LEVELING SWITCH - INSTALLATION,
HEADLAMP.........................8L-38
LEVELING SWITCH - OPERATION,
HEADLAMP.........................8L-37
LEVELING SWITCH - REMOVAL,
HEADLAMP.........................8L-38
LICENSE PLATE LAMP BULB -
INSTALLATION.......................8L-45
LICENSE PLATE LAMP BULB - REMOVAL . . 8L-44
LICENSE PLATE LAMP UNIT -
INSTALLATION.......................8L-46
LICENSE PLATE LAMP UNIT - REMOVAL . . 8L-45
LIFTERS - INSTALLATION, HYDRAULIC....9-29
LIFTERS - REMOVAL, HYDRAULIC........9-29
LOCKED ENGINE - STANDARD
PROCEDURE, HYDROSTATIC..............9-9
LOW BEAM RELAY - DESCRIPTION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - DIAGNOSIS AND
TESTING, HEADLAMP.................8L-40
LOW BEAM RELAY - INSTALLATION,
HEADLAMP.........................8L-41
LOW BEAM RELAY - OPERATION,
HEADLAMP.........................8L-39
LOW BEAM RELAY - REMOVAL,
HEADLAMP.........................8L-40
LOWER BALL JOINT - INSTALLATION......2-5
LOWER BALL JOINT - REMOVAL..........2-5
LOWER CONTROL ARM BUSHING -
INSTALLATION.........................2-3
LOWER CONTROL ARM BUSHING -
REMOVAL............................2-2
LOWER SUSPENSION ARM BUSHING -
INSTALLATION.........................2-8
LOWER SUSPENSION ARM BUSHING -
REMOVAL............................2-7
LUBRICATION - DESCRIPTION...........9-46
LUBRICATION - OPERATION
.............9-46
MAIN BEARING - FITTING - STANDARD
PROCEDURE
.........................9-35
MANIFOLD - CLEANING, EXHAUST
........9-53
MANIFOLD - DESCRIPTION, EXHAUST
.....9-53
MANIFOLD - DESCRIPTION, INTAKE
.......9-51
MANIFOLD - INSPECTION, EXHAUST
......9-53
MANIFOLD - INSPECTION, INTAKE
........9-52
MANIFOLD - INSTALLATION, EXHAUST
....9-53
MANIFOLD - INSTALLATION, INTAKE
......9-52
MANIFOLD - OPERATION, EXHAUST
.......9-53
MANIFOLD - OPERATION, INTAKE
........9-51
MANIFOLD - REMOVAL, EXHAUST
........9-53
MANIFOLD - REMOVAL, INTAKE
..........9-52
4 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1774 of 1803
MANIFOLD LEAKS - DIAGNOSIS AND
TESTING, INTAKE.....................9-51
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.........................9-11
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE......................9-7
MOTOR - DESCRIPTION, HEADLAMP
LEVELING..........................8L-35
MOTOR - INSTALLATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - OPERATION, HEADLAMP
LEVELING..........................8L-36
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-36
MOUNT - INSTALLATION, FRONT.........9-44
MOUNT - INSTALLATION, REAR..........9-45
MOUNT - REMOVAL, FRONT.............9-44
MOUNT - REMOVAL, REAR..............9-45
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH..............8L-18
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-19
MOUNTING - DESCRIPTION, ENGINE......9-44
MUFFLER - DESCRIPTION...............11-4
MUFFLER - INSTALLATION..............11-5
MUFFLER - REMOVAL..................11-4
MULTI-FUNCTION SWITCH -
DESCRIPTION.......................8L-46
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-50
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-53
MULTI-FUNCTION SWITCH - OPERATION . . 8L-48
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-53
NOISE DIAGNOSIS - DIAGNOSIS AND
TESTING, LASH ADJUSTER (TAPPET)......9-28
OFF - INSTALLATION, CYLINDER HEAD....9-28
OFF - REMOVAL, CYLINDER HEAD........9-27
OIL AND FILTER CHANGE - STANDARD
PROCEDURE, ENGINE..................9-47
OIL FILTER - DESCRIPTION.............9-47
OIL FILTER - INSTALLATION.............9-47
OIL FILTER - REMOVAL.................9-47
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE..............9-9
OIL LEAK INSPECTION - DIAGNOSIS
AND TESTING, ENGINE..................9-4
OIL LEVEL CHECK, STANDARD
PROCEDURE - ENGINE.................9-47
OIL PAN - INSTALLATION...............9-48
OIL PAN - REMOVAL...................9-48
OIL PRESSURE CHECKING - DIAGNOSIS
AND TESTING, ENGINE.................9-46
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-48
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-48
OIL PUMP - ASSEMBLY................9-50
OIL PUMP - CLEANING.................9-49
OIL PUMP - DISASSEMBLY.............9-49
OIL PUMP - INSPECTION...............9-50
OIL PUMP - INSTALLATION.............9-50
OIL PUMP - REMOVAL.................9-49
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT........................9-37
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT........................9-37
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT........................9-39
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT........................9-38
OIL SEAL(S) - INSTALLATION,
CAMSHAFT..........................9-22
OIL SEAL(S) - REMOVAL, CAMSHAFT.....9-22
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-2
OPERATION, BACKUP LAMP SWITCH.....8L-15
OPERATION, BALANCE SHAFT
...........9-59
OPERATION, BRAKE LAMP SWITCH
......8L-16
OPERATION, CAMSHAFT(S)
.............9-23
OPERATION, COMBINATION FLASHER
....8L-19
OPERATION, COOLANT RECOVERY
PRESS CONTAINER
....................7-20OPERATION, COOLING SYSTEM...........7-2
OPERATION, CRANKSHAFT..............9-33
OPERATION, CYLINDER HEAD...........9-19
OPERATION, DAYTIME RUNNING LAMP
RELAY.............................8L-20
OPERATION, DESCRIPTION..............7-20
OPERATION, ENGINE BLOCK HEATER -
2.4L................................7-20
OPERATION, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
OPERATION, EXHAUST MANIFOLD........9-53
OPERATION, FRONT FOG LAMP RELAY . . . 8L-22
OPERATION, HAZARD SWITCH..........8L-29
OPERATION, HEADLAMP HIGH BEAM
RELAY.............................8L-33
OPERATION, HEADLAMP LEVELING
MOTOR............................8L-36
OPERATION, HEADLAMP LEVELING
SWITCH............................8L-37
OPERATION, HEADLAMP LOW BEAM
RELAY.............................8L-39
OPERATION, HOSE CLAMPS..............7-2
OPERATION, INTAKE MANIFOLD..........9-51
OPERATION, LAMP BAR...............8L-65
OPERATION, LAMPS/LIGHTING -
EXTERIOR...........................8L-5
OPERATION, LUBRICATION..............9-46
OPERATION, MULTI-FUNCTION SWITCH . . . 8L-48
OPERATION, OIL PRESSURE SENSOR/
SWITCH..............................9-48
OPERATION, PARK LAMP RELAY........8L-54
OPERATION, PISTON & CONNECTING
ROD................................9-40
OPERATION, RADIATOR FAN - ELECTRIC . . . 7-26
OPERATION, RADIATOR PRESSURE CAP . . . 7-25
OPERATION, REAR FOG LAMP RELAY....8L-57
OPERATION, TRAILER TOW RELAY.......8L-62
OPERATION, WATER PUMP - 2.4L........7-27
PAN - INSTALLATION, OIL...............9-48
PAN - REMOVAL, OIL..................9-48
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-5
PIPE - INSTALLATION, CROSS-OVER......11-4
PIPE - REMOVAL, CROSS-OVER..........11-4
PISTON & CONNECTING ROD -
DESCRIPTION........................9-40
PISTON & CONNECTING ROD -
INSTALLATION........................9-41
PISTON & CONNECTING ROD -
OPERATION..........................9-40
PISTON & CONNECTING ROD -
REMOVAL...........................9-40
PISTON RING, FITTING.................9-42
PISTON TO CYLINDER BORE FITTING -
STANDARD PROCEDURE................9-30
PLASTIGAGE - STANDARD PROCEDURE,
MEASURING BEARING CLEARANCE
USING..............................9-11
PLATE LAMP BULB - INSTALLATION,
LICENSE...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE...........................8L-44
PLATE LAMP UNIT - INSTALLATION,
LICENSE...........................8L-46
PLATE LAMP UNIT - REMOVAL, LICENSE . . 8L-45
PLAY - STANDARD PROCEDURE,
CRANKSHAFT END....................9-33
PLUGS - STANDARD PROCEDURE,
ENGINE CORE AND OIL GALLERY.........9-9
POSITION LAMP BULB - INSTALLATION,
FRONT.............................8L-28
POSITION LAMP BULB - REMOVAL,
FRONT
.............................8L-28
PRELIMINARY CHECKS - DIAGNOSIS
AND TESTING
.........................7-2
PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET
SURFACE
............................9-11
PRESS CONTAINER - DESCRIPTION,
COOLANT RECOVERY
..................7-20
PRESS CONTAINER - OPERATION,
COOLANT RECOVERY
..................7-20PRESSURE CAP - CLEANING, RADIATOR . . . 7-25
PRESSURE CAP - DESCRIPTION,
RADIATOR...........................7-25
PRESSURE CAP - DIAGNOSIS AND
TESTING, RADIATOR...................7-25
PRESSURE CAP - INSPECTION,
RADIATOR...........................7-25
PRESSURE CAP - OPERATION,
RADIATOR...........................7-25
PRESSURE CHECKING - DIAGNOSIS AND
TESTING, ENGINE OIL..................9-46
PRESSURE LEAKAGE TEST - DIAGNOSIS
AND TESTING, CYLINDER
COMBUSTION.........................9-3
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-48
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-48
PRESSURE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMPRESSION.......9-3
PULLEY - INSTALLATION, TIMING BELT
TENSIONER..........................9-59
PULLEY - REMOVAL, TIMING BELT
TENSIONER..........................9-59
PUMP - 2.4L - DESCRIPTION, WATER.....7-27
PUMP - 2.4L - INSPECTION, WATER......7-28
PUMP - 2.4L - OPERATION, WATER.......7-27
PUMP - ASSEMBLY, OIL................9-50
PUMP - CLEANING, OIL................9-49
PUMP - DISASSEMBLY, OIL.............9-49
PUMP - INSPECTION, OIL...............9-50
PUMP - INSTALLATION, OIL.............9-50
PUMP - REMOVAL, OIL.................9-49
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-22
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-39
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-38
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-59
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-45
REAR MOUNT - REMOVAL..............9-45
REAR SUSPENSION, SPECIAL TOOLS......2-6
RECOVERY PRESS CONTAINER -
DESCRIPTION, COOLANT...............7-20
RECOVERY PRESS CONTAINER -
OPERATION, COOLANT.................7-20
REFILLING COOLING SYSTEM -
STANDARD PROCEDURE................7-11
RELAY - DESCRIPTION, DAYTIME
RUNNING LAMP.....................8L-20
RELAY - DESCRIPTION, FRONT FOG
LAMP..............................8L-22
RELAY - DESCRIPTION, HEADLAMP
HIGH BEAM
.........................8L-33
RELAY - DESCRIPTION, HEADLAMP LOW
BEAM
..............................8L-39
RELAY - DESCRIPTION, PARK LAMP
.....8L-54
RELAY - DESCRIPTION, REAR FOG LAMP
. 8L-56
RELAY - DESCRIPTION, TRAILER TOW
....8L-62
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page
Page 1775 of 1803
RELAY - DIAGNOSIS AND TESTING,
FRONT FOG LAMP....................8L-23
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP HIGH BEAM...............8L-34
RELAY - DIAGNOSIS AND TESTING,
HEADLAMP LOW BEAM...............8L-40
RELAY - DIAGNOSIS AND TESTING,
PARK LAMP.........................8L-55
RELAY - DIAGNOSIS AND TESTING,
REAR FOG LAMP.....................8L-57
RELAY - DIAGNOSIS AND TESTING,
TRAILER TOW.......................8L-62
RELAY - INSTALLATION, DAYTIME
RUNNING LAMP.....................8L-21
RELAY - INSTALLATION, FRONT FOG
LAMP..............................8L-24
RELAY - INSTALLATION, HEADLAMP
HIGH BEAM.........................8L-35
RELAY - INSTALLATION, HEADLAMP
LOW BEAM.........................8L-41
RELAY - INSTALLATION, PARK LAMP.....8L-56
RELAY - INSTALLATION, REAR FOG
LAMP..............................8L-58
RELAY - INSTALLATION, TRAILER TOW . . . 8L-63
RELAY - OPERATION, DAYTIME
RUNNING LAMP.....................8L-20
RELAY - OPERATION, FRONT FOG LAMP . . 8L-22
RELAY - OPERATION, HEADLAMP HIGH
BEAM..............................8L-33
RELAY - OPERATION, HEADLAMP LOW
BEAM..............................8L-39
RELAY - OPERATION, PARK LAMP.......8L-54
RELAY - OPERATION, REAR FOG LAMP . . . 8L-57
RELAY - OPERATION, TRAILER TOW.....8L-62
RELAY - REMOVAL, DAYTIME RUNNING
LAMP..............................8L-21
RELAY - REMOVAL, FRONT FOG LAMP . . . 8L-24
RELAY - REMOVAL, HEADLAMP HIGH
BEAM..............................8L-34
RELAY - REMOVAL, HEADLAMP LOW
BEAM..............................8L-40
RELAY - REMOVAL, PARK LAMP........8L-55
RELAY - REMOVAL, REAR FOG LAMP....8L-58
RELAY - REMOVAL, TRAILER TOW.......8L-63
REMOVAL - CLEANING.................9-55
REMOVAL - INSPECTION...............9-28
REMOVAL, 2.4L.......................7-20
REMOVAL, 2.4L.......................9-19
REMOVAL, 2.4L ENGINE....7-14,7-16,7-22,7-27
REMOVAL, BALANCE SHAFT.............9-60
REMOVAL, BALANCE SHAFT CARRIER.....9-64
REMOVAL, BALANCE SHAFT CHAIN.......9-64
REMOVAL, BRAKE LAMP SWITCH.......8L-17
REMOVAL, CAMSHAFT OIL SEAL(S).......9-22
REMOVAL, CAMSHAFT(S)...............9-24
REMOVAL, CATALYTIC CONVERTER.......11-2
REMOVAL, CENTER HIGH MOUNTED
STOP LAMP BULB....................8L-18
REMOVAL, CENTER HIGH MOUNTED
STOP LAMP UNIT....................8L-19
REMOVAL, CLEVIS BRACKET BUSHING.....2-2
REMOVAL, CRANKSHAFT...............9-33
REMOVAL, CRANKSHAFT OIL SEAL -
FRONT..............................9-37
REMOVAL, CRANKSHAFT OIL SEAL -
REAR...............................9-38
REMOVAL, CRANKSHAFT SPROCKET......9-55
REMOVAL, CROSS-OVER PIPE...........11-4
REMOVAL, CYLINDER HEAD.............9-20
REMOVAL, CYLINDER HEAD COVER.......9-26
REMOVAL, CYLINDER HEAD OFF.........9-27
REMOVAL, CYLINDER HEAD ON..........9-27
REMOVAL, DAYTIME RUNNING LAMP
RELAY.............................8L-21
REMOVAL, ENGINE ASSEMBLY...........9-12
REMOVAL, ENGINE COOLANT
TEMPERATURE SENSOR................7-21
REMOVAL, EXHAUST MANIFOLD.........9-53
REMOVAL, FRONT FOG LAMP BULB......8L-21
REMOVAL, FRONT FOG LAMP RELAY.....8L-24
REMOVAL, FRONT FOG LAMP UNIT......8L-24
REMOVAL, FRONT LAMP BULB.........8L-27
REMOVAL, FRONT LAMP UNIT
..........8L-27
REMOVAL, FRONT MOUNT
..............9-44
REMOVAL, FRONT POSITION LAMP
BULB
..............................8L-28
REMOVAL, HAZARD SWITCH
...........8L-29
REMOVAL, HEADLAMP BULB
...........8L-30REMOVAL, HEADLAMP HIGH BEAM
RELAY.............................8L-34
REMOVAL, HEADLAMP LEVELING
MOTOR............................8L-36
REMOVAL, HEADLAMP LEVELING
SWITCH............................8L-38
REMOVAL, HEADLAMP LOW BEAM
RELAY.............................8L-40
REMOVAL, HEADLAMP UNIT...........8L-41
REMOVAL, HYDRAULIC LIFTERS.........9-29
REMOVAL, INTAKE MANIFOLD...........9-52
REMOVAL, LAMP....................8L-66
REMOVAL, LAMP BAR................8L-65
REMOVAL, LAMP BAR SWITCH.........8L-67
REMOVAL, LICENSE PLATE LAMP BULB . . 8L-44
REMOVAL, LICENSE PLATE LAMP UNIT . . . 8L-45
REMOVAL, LOWER BALL JOINT...........2-5
REMOVAL, LOWER CONTROL ARM
BUSHING.............................2-2
REMOVAL, LOWER SUSPENSION ARM
BUSHING.............................2-7
REMOVAL, MUFFLER...................11-4
REMOVAL, MULTI-FUNCTION SWITCH....8L-53
REMOVAL, OIL FILTER.................9-47
REMOVAL, OIL PAN...................9-48
REMOVAL, OIL PUMP..................9-49
REMOVAL, PARK LAMP RELAY..........8L-55
REMOVAL, PISTON & CONNECTING ROD . . . 9-40
REMOVAL, RADIATOR..................7-22
REMOVAL, RADIATOR FAN - ELECTRIC....7-26
REMOVAL, REAR FOG LAMP RELAY......8L-58
REMOVAL, REAR LAMP BULB..........8L-59
REMOVAL, REAR LAMP UNIT...........8L-59
REMOVAL, REAR MOUNT...............9-45
REMOVAL, REPEATER LAMP BULB.......8L-60
REMOVAL, REPEATER LAMP UNIT.......8L-61
REMOVAL, RHD........................5-1
REMOVAL, ROCKER ARMS..............9-29
REMOVAL, STRUCTURAL COLLAR........9-44
REMOVAL, TIMING BELT................9-55
REMOVAL, TIMING BELT COVER(S).......9-53
REMOVAL, TIMING BELT TENSIONER &
PULLEY.............................9-59
REMOVAL, TRAILER TOW CONNECTOR . . . 8L-61
REMOVAL, TRAILER TOW RELAY........8L-63
REMOVAL, UPPER BALL JOINT...........2-6
REMOVAL, UPPER CONTROL ARM
BUSHINGS............................2-3
REMOVAL, UPPER SUSPENSION ARM
BUSHING.............................2-7
REMOVAL, VIBRATION DAMPER..........9-43
REPAIR OF DAMAGED OR WORN
THREADS - STANDARD PROCEDURE.......9-9
REPEATER LAMP BULB - INSTALLATION . . 8L-60
REPEATER LAMP BULB - REMOVAL......8L-60
REPEATER LAMP UNIT - INSTALLATION . . 8L-61
REPEATER LAMP UNIT - REMOVAL......8L-61
REVERSE FLUSHING - STANDARD
PROCEDURE, COOLING SYSTEM.........7-12
RHD - INSTALLATION...................5-1
RHD - REMOVAL.......................5-1
RING, FITTING - PISTON................9-42
ROCKER ARMS - INSPECTION...........9-30
ROCKER ARMS - INSTALLATION.........9-30
ROCKER ARMS - REMOVAL.............9-29
ROD - DESCRIPTION, PISTON &
CONNECTING.........................9-40
ROD - INSTALLATION, PISTON &
CONNECTING.........................9-41
ROD - OPERATION, PISTON &
CONNECTING.........................9-40
ROD - REMOVAL, PISTON &
CONNECTING.........................9-40
ROD, FITTING - CONNECTING............9-32
RUNNING LAMP RELAY - DESCRIPTION,
DAYTIME...........................8L-20
RUNNING LAMP RELAY - INSTALLATION,
DAYTIME...........................8L-21
RUNNING LAMP RELAY - OPERATION,
DAYTIME
...........................8L-20
RUNNING LAMP RELAY - REMOVAL,
DAYTIME
...........................8L-21
SEAL - FRONT - INSTALLATION,
CRANKSHAFT OIL
.....................9-37
SEAL - FRONT - REMOVAL,
CRANKSHAFT OIL
.....................9-37
SEAL - REAR - INSTALLATION,
CRANKSHAFT OIL
.....................9-39SEAL - REAR - REMOVAL, CRANKSHAFT
OIL ................................9-38
SEALERS - STANDARD PROCEDURE,
FORM-IN-PLACE GASKETS..............9-10
SEAL(S) - INSTALLATION, CAMSHAFT
OIL ................................9-22
SEAL(S) - REMOVAL, CAMSHAFT OIL.....9-22
SEATS - CLEANING, INTAKE/EXHAUST
VALVES .............................9-27
SEATS - DESCRIPTION, INTAKE/
EXHAUST VALVES.....................9-27
SENSOR - DESCRIPTION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - INSTALLATION, ENGINE
COOLANT TEMPERATURE...............7-22
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-21
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-21
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-48
SENSOR/SWITCH - OPERATION, OIL
PRESSURE..........................9-48
SERPENTINE DRIVE BELT DIAGNOSIS -
DIAGNOSIS AND TESTING..............7-15
SHAFT - DESCRIPTION, BALANCE........9-59
SHAFT - OPERATION, BALANCE..........9-59
SHAFT - REMOVAL, BALANCE...........9-60
SHAFT CARRIER - INSTALLATION,
BALANCE............................9-64
SHAFT CARRIER - REMOVAL, BALANCE....9-64
SHAFT CHAIN - INSTALLATION,
BALANCE............................9-64
SHAFT CHAIN - REMOVAL, BALANCE......9-64
SHAFT TIMING, INSTALLATION -
BALANCE............................9-61
SHIELDS - DESCRIPTION, HEAT..........11-4
SPECIAL TOOLS - 2.4L ENGINE..........9-17
SPECIAL TOOLS - COOLING.............7-13
SPECIAL TOOLS - FRONT SUSPENSION.....2-1
SPECIAL TOOLS - REAR SUSPENSION......2-6
SPECIFICATIONS - TORQUE.............7-13
SPECIFICATIONS, 2.4L ENGINE...........9-13
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, TORQUE..............9-16
SPROCKET - INSTALLATION,
CRANKSHAFT........................9-56
SPROCKET - REMOVAL, CRANKSHAFT.....9-55
STANDARD PROCEDURE - CLEANING.....9-31
STANDARD PROCEDURE - ENGINE OIL
LEVEL CHECK........................9-47
STANDARD PROCEDURE - INSPECTION....9-32
STANDARD PROCEDURE, CAMSHAFT
END-PLAY...........................9-23
STANDARD PROCEDURE, COOLING
SYSTEM - REVERSE FLUSHING..........7-12
STANDARD PROCEDURE, CRANKSHAFT
END PLAY ...........................9-33
STANDARD PROCEDURE, CYLINDER
BORE HONING........................9-31
STANDARD PROCEDURE, DRAINING
COOLING SYSTEM....................7-11
STANDARD PROCEDURE, ENGINE CORE
AND OIL GALLERY PLUGS...............9-9
STANDARD PROCEDURE, ENGINE
GASKET SURFACE PREPARATION.........9-11
STANDARD PROCEDURE, ENGINE OIL
AND FILTER CHANGE..................9-47
STANDARD PROCEDURE, FLUSHING
COOLERS AND TUBES.................7-30
STANDARD PROCEDURE, FORM-IN-
PLACE GASKETS AND SEALERS..........9-10
STANDARD PROCEDURE, HYDROSTATIC
LOCKED ENGINE.......................9-9
STANDARD PROCEDURE, LAMP BAR
AIMING............................8L-65
STANDARD PROCEDURE, MAIN BEARING
- FITTING
............................9-35
STANDARD PROCEDURE, MEASURING
BEARING CLEARANCE USING
PLASTIGAGE
.........................9-11
STANDARD PROCEDURE, PISTON TO
CYLINDER BORE FITTING
...............9-30
STANDARD PROCEDURE, REFILLING
COOLING SYSTEM
....................7-11
STANDARD PROCEDURE, REPAIR OF
DAMAGED OR WORN THREADS
...........9-9
6 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1776 of 1803
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED.....................8L-18
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-19
STRUCTURAL COLLAR - INSTALLATION....9-44
STRUCTURAL COLLAR - REMOVAL.......9-44
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET...........9-11
SUSPENSION ARM BUSHING -
INSTALLATION, LOWER.................2-8
SUSPENSION ARM BUSHING -
INSTALLATION, UPPER..................2-8
SUSPENSION ARM BUSHING -
REMOVAL, LOWER.....................2-7
SUSPENSION ARM BUSHING -
REMOVAL, UPPER......................2-7
SUSPENSION, SPECIAL TOOLS - FRONT....2-1
SUSPENSION, SPECIAL TOOLS - REAR.....2-6
SWITCH - DESCRIPTION, BACKUP LAMP . . 8L-15
SWITCH - DESCRIPTION, BRAKE LAMP . . . 8L-16
SWITCH - DESCRIPTION, HAZARD.......8L-28
SWITCH - DESCRIPTION, HEADLAMP
LEVELING..........................8L-37
SWITCH - DESCRIPTION, LAMP BAR.....8L-67
SWITCH - DESCRIPTION, MULTI-
FUNCTION..........................8L-46
SWITCH - DIAGNOSIS AND TESTING,
BACKUP LAMP......................8L-15
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP.......................8L-17
SWITCH - DIAGNOSIS AND TESTING,
HEADLAMP LEVELING.................8L-37
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-50
SWITCH - INSTALLATION, BRAKE LAMP . . 8L-18
SWITCH - INSTALLATION, HAZARD......8L-30
SWITCH - INSTALLATION, HEADLAMP
LEVELING..........................8L-38
SWITCH - INSTALLATION, LAMP BAR....8L-67
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-53
SWITCH - OPERATION, BACKUP LAMP . . . 8L-15
SWITCH - OPERATION, BRAKE LAMP.....8L-16
SWITCH - OPERATION, HAZARD.........8L-29
SWITCH - OPERATION, HEADLAMP
LEVELING..........................8L-37
SWITCH - OPERATION, MULTI-FUNCTION . 8L-48
SWITCH - REMOVAL, BRAKE LAMP......8L-17
SWITCH - REMOVAL, HAZARD..........8L-29
SWITCH - REMOVAL, HEADLAMP
LEVELING..........................8L-38
SWITCH - REMOVAL, LAMP BAR........8L-67
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-53
SYSTEM - DESCRIPTION, EXHAUST.......11-1
SYSTEM - DIAGNOSIS AND TESTING,
EXHAUST............................11-2
SYSTEM - OPERATION, COOLING..........7-2
SYSTEM - REVERSE FLUSHING -
STANDARD PROCEDURE, COOLING.......7-12
SYSTEM - STANDARD PROCEDURE,
DRAINING COOLING...................7-11
SYSTEM - STANDARD PROCEDURE,
REFILLING COOLING...................7-11
SYSTEM 2.4L ENGINE - DESCRIPTION,
COOLING.............................7-1
SYSTEM DIAGNOSIS CHART -
DIAGNOSIS AND TESTING, COOLING.......7-5
SYSTEM LEAKS - DIAGNOSIS AND
TESTING, COOLING.....................7-2
TEMPERATURE SENSOR - DESCRIPTION,
ENGINE COOLANT.....................7-21
TEMPERATURE SENSOR -
INSTALLATION, ENGINE COOLANT........7-22
TEMPERATURE SENSOR - OPERATION,
ENGINE COOLANT.....................7-21
TEMPERATURE SENSOR - REMOVAL,
ENGINE COOLANT.....................7-21TENSIONER & PULLEY - INSTALLATION,
TIMING BELT.........................9-59
TENSIONER & PULLEY - REMOVAL,
TIMING BELT.........................9-59
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE.............................9-3
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION PRESSURE......9-3
TESTING, BACKUP LAMP SWITCH -
DIAGNOSIS.........................8L-15
TESTING, BRAKE LAMP SWITCH -
DIAGNOSIS.........................8L-17
TESTING, COOLING SYSTEM DIAGNOSIS
CHART - DIAGNOSIS....................7-5
TESTING, COOLING SYSTEM LEAKS -
DIAGNOSIS...........................7-2
TESTING, CYLINDER COMBUSTION
PRESSURE LEAKAGE TEST -
DIAGNOSIS...........................9-3
TESTING, CYLINDER COMPRESSION
PRESSURE TEST - DIAGNOSIS............9-3
TESTING, CYLINDER HEAD GASKET -
DIAGNOSIS..........................9-19
TESTING, ENGINE - DIAGNOSIS...........9-5
TESTING, ENGINE DIAGNOSIS -
PERFORMANCE - DIAGNOSIS.............9-5
TESTING, ENGINE MECHANICAL -
DIAGNOSIS...........................9-7
TESTING, ENGINE OIL LEAK
INSPECTION - DIAGNOSIS...............9-4
TESTING, ENGINE OIL PRESSURE
CHECKING - DIAGNOSIS................9-46
TESTING, EXHAUST SYSTEM -
DIAGNOSIS..........................11-2
TESTING, FRONT FOG LAMP RELAY -
DIAGNOSIS.........................8L-23
TESTING, HEADLAMP HIGH BEAM
RELAY - DIAGNOSIS
..................8L-34
TESTING, HEADLAMP LEVELING SWITCH
- DIAGNOSIS
........................8L-37
TESTING, HEADLAMP LOW BEAM RELAY
- DIAGNOSIS
........................8L-40
TESTING, INTAKE MANIFOLD LEAKS -
DIAGNOSIS
..........................9-51
TESTING, LAMP BAR - DIAGNOSIS
......8L-65
TESTING, LAMPS/LIGHTING - EXTERIOR
- DIAGNOSIS
.........................8L-7
TESTING, LASH ADJUSTER (TAPPET)
NOISE DIAGNOSIS - DIAGNOSIS
.........9-28
TESTING, MULTI-FUNCTION SWITCH -
DIAGNOSIS
.........................8L-50
TESTING, ON-BOARD DIAGNOSTICS
(OBD) - DIAGNOSIS
....................7-2
TESTING, PARK LAMP RELAY -
DIAGNOSIS
.........................8L-55
TESTING, PRELIMINARY CHECKS -
DIAGNOSIS
...........................7-2
TESTING, RADIATOR PRESSURE CAP -
DIAGNOSIS
..........................7-25
TESTING, REAR FOG LAMP RELAY -
DIAGNOSIS
.........................8L-57
TESTING, SERPENTINE DRIVE BELT
DIAGNOSIS - DIAGNOSIS
...............7-15
TESTING, TRAILER TOW RELAY -
DIAGNOSIS
.........................8L-62
THREADS - STANDARD PROCEDURE,
REPAIR OF DAMAGED OR WORN
..........9-9
TIMING BELT - INSTALLATION
...........9-56
TIMING BELT - REMOVAL
...............9-55
TIMING BELT COVER(S) - INSTALLATION
. . . 9-53
TIMING BELT COVER(S) - REMOVAL
......9-53
TIMING BELT TENSIONER & PULLEY -
INSTALLATION
........................9-59
TIMING BELT TENSIONER & PULLEY -
REMOVAL
...........................9-59
TIMING, INSTALLATION - BALANCE
SHAFT
..............................9-61TO CYLINDER BORE FITTING -
STANDARD PROCEDURE, PISTON........9-30
TOOLS - 2.4L ENGINE, SPECIAL..........9-17
TOOLS - COOLING, SPECIAL.............7-13
TOOLS - FRONT SUSPENSION, SPECIAL....2-1
TOOLS - REAR SUSPENSION, SPECIAL.....2-6
TORQUE - SPECIFICATIONS.............9-16
TORQUE, SPECIFICATIONS..............7-13
TOW CONNECTOR - INSTALLATION,
TRAILER...........................8L-61
TOW CONNECTOR - REMOVAL, TRAILER . . 8L-61
TOW RELAY - DESCRIPTION, TRAILER....8L-62
TOW RELAY - DIAGNOSIS AND TESTING,
TRAILER...........................8L-62
TOW RELAY - INSTALLATION, TRAILER . . . 8L-63
TOW RELAY - OPERATION, TRAILER.....8L-62
TOW RELAY - REMOVAL, TRAILER.......8L-63
TOW WIRING - DESCRIPTION, TRAILER . . 8L-64
TRAILER TOW CONNECTOR -
INSTALLATION.......................8L-61
TRAILER TOW CONNECTOR - REMOVAL . . 8L-61
TRAILER TOW RELAY - DESCRIPTION....8L-62
TRAILER TOW RELAY - DIAGNOSIS AND
TESTING...........................8L-62
TRAILER TOW RELAY - INSTALLATION . . . 8L-63
TRAILER TOW RELAY - OPERATION......8L-62
TRAILER TOW RELAY - REMOVAL.......8L-63
TRAILER TOW WIRING - DESCRIPTION . . . 8L-64
TRANS COOLER - DESCRIPTION.........7-30
TUBES - STANDARD PROCEDURE,
FLUSHING COOLERS...................7-30
UNIT - ADJUSTMENT, FRONT FOG LAMP . . 8L-25
UNIT - ADJUSTMENT, HEADLAMP.......8L-42
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
UNIT - INSTALLATION, FRONT FOG
LAMP..............................8L-25
UNIT - INSTALLATION, FRONT LAMP.....8L-28
UNIT - INSTALLATION, HEADLAMP.......8L-42
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-46
UNIT - INSTALLATION, REAR LAMP......8L-60
UNIT - INSTALLATION, REPEATER LAMP . . 8L-61
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP
................8L-19
UNIT - REMOVAL, FRONT FOG LAMP
.....8L-24
UNIT - REMOVAL, FRONT LAMP
.........8L-27
UNIT - REMOVAL, HEADLAMP
..........8L-41
UNIT - REMOVAL, LICENSE PLATE LAMP
. . 8L-45
UNIT - REMOVAL, REAR LAMP
..........8L-59
UNIT - REMOVAL, REPEATER LAMP
......8L-61
UPPER BALL JOINT - INSTALLATION
.......2-6
UPPER BALL JOINT - REMOVAL
...........2-6
UPPER CONTROL ARM BUSHINGS -
INSTALLATION
.........................2-4
UPPER CONTROL ARM BUSHINGS -
REMOVAL
............................2-3
UPPER SUSPENSION ARM BUSHING -
INSTALLATION
.........................2-8
UPPER SUSPENSION ARM BUSHING -
REMOVAL
............................2-7
USING PLASTIGAGE - STANDARD
PROCEDURE, MEASURING BEARING
CLEARANCE
..........................9-11
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST
.....................9-27
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST
.....................9-27
VIBRATION DAMPER - INSTALLATION
.....9-43
VIBRATION DAMPER - REMOVAL
.........9-43
WATER PUMP - 2.4L - DESCRIPTION
......7-27
WATER PUMP - 2.4L - INSPECTION
.......7-28
WATER PUMP - 2.4L - OPERATION
.......7-27
WIRING - DESCRIPTION, TRAILER TOW
. . 8L-64
WORN THREADS - STANDARD
PROCEDURE, REPAIR OF DAMAGED
OR
..................................9-9
KJINDEX 7
Description Group-Page Description Group-Page Description Group-Page