Oil transfer JEEP LIBERTY 2002 KJ / 1.G Owner's Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2002, Model line: LIBERTY, Model: JEEP LIBERTY 2002 KJ / 1.GPages: 1803, PDF Size: 62.3 MB
Page 1654 of 1803
DESCRIPTION - REFRIGERANT SYSTEM
SERVICE PORT
The two refrigerant system service ports are used
to charge, recover/recycle, evacuate, and test the air
conditioning refrigerant system. Unique service port
coupler sizes are used on the R-134a system, to
ensure that the refrigerant system is not accidentally
contaminated by the use of the wrong refrigerant
(R-12), or refrigerant system service equipment.
OPERATION
OPERATION - HEATER AND AIR CONDITIONER
The heater and optional air conditioner are blend-
air type systems. In a blend-air system, a blend door
controls the amount of unconditioned air (or cooled
air from the evaporator on models with air condition-
ing) that is allowed to flow through, or around, the
heater core. A temperature control knob on the A/C
Heater control panel determines the discharge air
temperature by controlling an electric actuator,
which moves the blend door. This allows an almost
immediate control of the output air temperature of
the system.
The mode control knob on the heater-only or A/C
Heater control panel is used to direct the conditioned
air to the selected system outlets. Both mode control
switches use engine vacuum to control the mode
doors, which are operated by vacuum actuators.
On all vehicles, the outside air intake can be shut
off by selecting the Recirculation Mode with the
mode control knob. This will operate a vacuum actu-
ated recirculation door that closes off the outside
fresh air intake and recirculates the air that is
already inside the vehicle.
The optional air conditioner for all models is
designed for the use of non-CFC, R-134a refrigerant.
The air conditioning system has an evaporator to cool
and dehumidify the incoming air prior to blending it
with the heated air. This air conditioning system
uses a fixed orifice tube in the liquid line near the
condenser outlet tube to meter refrigerant flow to the
evaporator coil. To maintain minimum evaporator
temperature and prevent evaporator freezing, the
A/C low pressure switch on the accumulator cycles
the compressor clutch.
OPERATION - REFRIGERANT SYSTEM SERVICE
PORT
The high pressure service port is located on the
refrigerant line, near the discharge port of the com-
pressor. The low pressure service port is located on
the liquid line at the side of the engine compartment,
near the condensor.Each of the service ports has a threaded plastic
protective cap installed over it from the factory. After
servicing the refrigerant system, always reinstall
both of the service port caps.
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - A/C
PERFORMANCE
The air conditioning system is designed to provide
the passenger compartment with low temperature
and low humidity air. The evaporator, located in the
HVAC housing on the dash panel below the instru-
ment panel, is cooled to temperatures near the freez-
ing point. As warm damp air passes through the
cooled evaporator, the air transfers its heat to the
refrigerant in the evaporator and the moisture in the
air condenses on the evaporator fins. During periods
of high heat and humidity, an air conditioning sys-
tem will be more effective in the Recirculation Mode.
With the system in the Recirculation Mode, only air
from the passenger compartment passes through the
evaporator. As the passenger compartment air dehu-
midifies, the air conditioning system performance
levels improve.
Humidity has an important bearing on the temper-
ature of the air delivered to the interior of the vehi-
cle. It is important to understand the effect that
humidity has on the performance of the air condition-
ing system. When humidity is high, the evaporator
has to perform a double duty. It must lower the air
temperature, and it must lower the temperature of
the moisture in the air that condenses on the evapo-
rator fins. Condensing the moisture in the air trans-
fers heat energy into the evaporator fins and tubing.
This reduces the amount of heat the evaporator can
absorb from the air. High humidity greatly reduces
the ability of the evaporator to lower the temperature
of the air.
However, evaporator capacity used to reduce the
amount of moisture in the air is not wasted. Remov-
ing some of the moisture out of the air entering the
vehicle adds to the comfort of the passengers.
Although, an owner may expect too much from the
air conditioning system on humid days. A perfor-
mance test is the best way to determine whether the
system is performing up to standard. This test also
provides valuable clues as to the possible cause of
trouble with the air conditioning system.
Before proceeding, (Refer to 24 - HEATING & AIR
CONDITIONING/PLUMBING - WARNING) and
(Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING - CAUTION). The air temperature in
the test room and in the vehicle must be a minimum
of 21É C (70É F) for this test.
24 - 2 HEATING & AIR CONDITIONINGKJ
HEATING & AIR CONDITIONING (Continued)
Page 1704 of 1803
evaporator outlet tube. Connect the accumulator inlet
tube refrigerant line coupler to the evaporator outlet
tube. (Refer to 24 - HEATING & AIR CONDITION-
ING/PLUMBING - STANDARD PROCEDURE - A/C
LINE COUPLERS)
(3) Tighten the accumulator retaining band screw
to 5 N´m (45 in. lbs.).
(4) Remove the tape or plugs from the refrigerant
line fittings on the suction line and the accumulator
outlet tube. Connect the suction line to the accumu-
lator outlet tube refrigerant line coupler. (Refer to 24
- HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - A/C LINE COUPLERS)
(5) Plug the wire harness connector into the low
pressure cycling clutch switch.
(6) Connect the battery negative cable.
(7) Evacuate the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM EVACUATE)
(8) Charge the refrigerant system. (Refer to 24 -
HEATING & AIR CONDITIONING/PLUMBING -
STANDARD PROCEDURE - REFRIGERANT SYS-
TEM CHARGE)NOTE: If the accumulator is replaced, add 120 mil-
liliters (4 fluid ounces) of refrigerant oil to the
refrigerant system. Use only refrigerant oil of the
type recommended for the compressor in the vehi-
cle. (Refer to 24 - HEATING & AIR CONDITIONING/
PLUMBING/REFRIGERANT OIL - DESCRIPTION)
HEATER CORE
DESCRIPTION
The heater core is located in the HVAC housing,
under the instrument panel. It is a heat exchanger
made of rows of tubes and fins and uses warm engine
coolant as its heat source.
OPERATION
Engine coolant is circulated through heater hoses
to the heater core at all times. As the coolant flows
through the heater core, heat removed from the
engine is transferred to the heater core fins and
tubes. Air directed through the heater core picks up
the heat from the heater core fins. The temperature
control door allows control of the heater output air
temperature by controlling how much of the air flow-
ing through the HVAC housing is directed through
the heater core. The blower motor speed controls the
volume of air flowing through the HVAC housing.
The heater core cannot be repaired and, if faulty or
damaged, it must be replaced. Refer to Cooling for
more information on the engine cooling system, the
engine coolant and the heater hoses.
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
Fig. 13 A/C LOW PRESSURE SWITCH
1 - WIRING HARNESS CONNECTOR
2 - A/C LOW PRESSURE SWITCH
3 - A/C LINE TO EVAPORATOR
4 - ACCUMULATOR MOUNTING BRACKET
5 - ACCUMULATOR
6 - A/C LOW PRESSURE LINE
24 - 52 PLUMBINGKJ
ACCUMULATOR (Continued)
Page 1741 of 1803
ANTENNA BODY & CABLE - OPERATION . . . 8A-5
ANTENNA BODY & CABLE - REMOVAL.....8A-6
ANTENNA BODY AND CABLE -
DIAGNOSIS AND TESTING..............8A-5
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-8
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-7
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER.......................8E-10
ANTILOCK BRAKE - REMOVAL,
CONTROLLER.......................8E-10
ANTILOCK BRAKING SYSTEM -
DIAGNOSIS AND TESTING..............5-33
A-PILLAR SEAL - INSTALLATION.......23-185
A-PILLAR SEAL - REMOVAL...........23-185
A-PILLAR TRIM AND GRAB HANDLE -
INSTALLATION......................23-156
A-PILLAR TRIM AND GRAB HANDLE -
REMOVAL.........................23-156
A-PILLAR WEATHERSTRIP/RETAINER -
INSTALLATION, WINDSHIELD..........23-187
A-PILLAR WEATHERSTRIP/RETAINER -
REMOVAL, WINDSHIELD..............23-186
APPLICATION TABLE, SPECIFICATIONS -
A/C ................................24-9
AREA LEAKS - DIAGNOSIS AND
TESTING, REAR SEAL..................9-61
ARM - DESCRIPTION, FRONT WIPER.....8R-12
ARM - DESCRIPTION, LOWER CONTROL . . . 2-21
ARM - DESCRIPTION, REAR WIPER......8R-37
ARM - DESCRIPTION, ROCKER......9-29,9-37
ARM - INSTALLATION, FRONT WIPER....8R-13
ARM - INSTALLATION, LOWER CONTROL . . 2-10,
2-21
ARM - INSTALLATION, REAR WIPER.....8R-38
ARM - INSTALLATION, ROCKER..........9-37
ARM - INSTALLATION, UPPER CONTROL . . . 2-21
ARM - OPERATION, FRONT WIPER......8R-12
ARM - OPERATION, LOWER CONTROL.....2-21
ARM - OPERATION, REAR WIPER.......8R-38
ARM - REMOVAL, FRONT WIPER........8R-12
ARM - REMOVAL, LOWER CONTROL . . 2-10,2-21
ARM - REMOVAL, REAR WIPER.........8R-38
ARM - REMOVAL, ROCKER..............9-37
ARM - REMOVAL, UPPER CONTROL......2-20
ARM, BUSHINGS, AND BALL JOINT -
DESCRIPTION, UPPER SUSPENSION......2-20
ARM, BUSHINGS, AND BALL JOINT -
OPERATION, UPPER SUSPENSION........2-20
ARM PARK RAMP - INSTALLATION,
WIPER.............................8R-43
ARM PARK RAMP - REMOVAL, WIPER . . . 8R-43
ASD AND FUEL PUMP RELAYS -
DIAGNOSIS AND TESTING...............8I-4
ASD SENSE - PCM INPUT - OPERATION....8I-4
ASH RECEIVER LAMP BULB -
INSTALLATION.......................8L-71
ASH RECEIVER LAMP BULB - REMOVAL . . 8L-71
ASH RECEIVER LAMP UNIT -
INSTALLATION.......................8L-72
ASH RECEIVER LAMP UNIT - REMOVAL . . 8L-72
ASSEMBLY - ASSEMBLY, INPUT CLUTCH . 21-138
ASSEMBLY - DESCRIPTION, INPUT
CLUTCH...........................21-133
ASSEMBLY - DESCRIPTION,
TRANSMISSION SOLENOID/TRS........21-169
ASSEMBLY - DISASSEMBLY, INPUT
CLUTCH...........................21-135
ASSEMBLY - INSTALLATION.........8W-97-11
ASSEMBLY - INSTALLATION, GUIDE.....23-179
ASSEMBLY - INSTALLATION,
INSTRUMENT PANEL.................23-151
ASSEMBLY - INSTALLATION, MODULE . . . 23-181
ASSEMBLY - INSTALLATION,
TRANSMISSION SOLENOID/TRS........21-170
ASSEMBLY - OPERATION, INPUT
CLUTCH...........................21-135
ASSEMBLY - OPERATION,
TRANSMISSION SOLENOID/TRS........21-169
ASSEMBLY - POWER DISTRIBUTION
CENTER ASSEMBLY
...............8W-97-10
ASSEMBLY - REMOVAL, GUIDE
........23-179
ASSEMBLY - REMOVAL, INSTRUMENT
PANEL
............................23-149
ASSEMBLY - REMOVAL, MODULE
......23-181
ASSEMBLY - REMOVAL, TRANSMISSION
SOLENOID/TRS
.....................21-170ASSEMBLY, 4C RETAINER/BULKHEAD....21-123
ASSEMBLY, ASSEMBLY - POWER
DISTRIBUTION CENTER............8W-97-10
ASSEMBLY, DIAGNOSIS AND TESTING....21-90
ASSEMBLY, DIFFERENTIAL.........3-105,3-41
ASSEMBLY, DIFFERENTIAL - TRAC-LOK . . . 3-109,
3-77
ASSEMBLY, DISC BRAKE CALIPERS.......5-16
ASSEMBLY, HVAC HOUSING............24-34
ASSEMBLY, INPUT CLUTCH ASSEMBLY . . 21-138
ASSEMBLY, INSTRUMENT CLUSTER......8J-10
ASSEMBLY, LOW/REVERSE CLUTCH.....21-146
ASSEMBLY, MANUAL - NV1500.........21-13
ASSEMBLY, MANUAL - NV3550.........21-48
ASSEMBLY, OIL PUMP.................9-67
ASSEMBLY, OIL PUMP...............21-151
ASSEMBLY, PLANETARY GEARTRAIN....21-160
ASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-9
ASSEMBLY, TRANSFER CASE - NV231 . . . 21-194
ASSEMBLY, TRANSFER CASE - NV242 . . . 21-230
ASSEMBLY, VALVE BODY.............21-176
ASSEMBLY, WHEEL CYLINDERS..........5-29
ASSEMBLY WINDOW DEFOGGER
FUNCTION - DIAGNOSIS AND TESTING,
REAR HVAC CONTROL.................8G-9
ASSIST HANDLE - INSTALLATION.......23-157
ASSIST HANDLE - REMOVAL............23-157
AUDIO - DESCRIPTION.................8A-1
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO - OPERATION...................8A-1
AUTOMATIC TRANSMISSION - 45RFE -
DESCRIPTION.......................21-76
AUTOMATIC TRANSMISSION - 45RFE -
OPERATION.........................21-77
AUTOMATIC TRANSMISSION -
DIAGNOSIS AND TESTING.............21-77
AUTOMATIC TRANSMISSION FLUID -
DESCRIPTION.........................0-2
AUTOMATIC TRANSMISSION FLUID -
OPERATION...........................0-4
AXLE - 186FIA - ADJUSTMENTS, FRONT . . . 3-25
AXLE - 186FIA - DESCRIPTION, FRONT....3-19
AXLE - 186FIA - INSTALLATION, FRONT....3-24
AXLE - 186FIA - OPERATION, FRONT......3-19
AXLE - 186FIA - REMOVAL, FRONT.......3-24
AXLE - 198RBI - DESCRIPTION, REAR.....3-49
AXLE - 198RBI - INSTALLATION, REAR....3-54
AXLE - 198RBI - OPERATION, REAR.......3-49
AXLE - 198RBI - REMOVAL, REAR........3-54
AXLE - 8 1/4 - ADJUSTMENTS, REAR.....3-92
AXLE - 8 1/4 - DESCRIPTION, REAR......3-86
AXLE - 8 1/4 - INSTALLATION, REAR......3-91
AXLE - 8 1/4 - OPERATION, REAR........3-86
AXLE - 8 1/4 - REMOVAL, REAR..........3-91
AXLE - DESCRIPTION...................0-2
AXLE - DIAGNOSIS AND TESTING....3-20,3-51,
3-88
AXLE - INSTALLATION, 198 RBI..........5-28
AXLE - INSTALLATION, 8 1/4............5-28
AXLE - REMOVAL, 198 RBI..............5-27
AXLE - REMOVAL, 8 1/4................5-27
AXLE - SPECIFICATIONS, FRONT.........3-33
AXLE - SPECIFICATIONS, REAR..........3-62
AXLE BEARINGS - INSTALLATION....3-102,3-38
AXLE BEARINGS - REMOVAL.......3-102,3-38
AXLE BEARING/SEAL - INSTALLATION.....3-67
AXLE BEARING/SEAL - REMOVAL.........3-66
AXLE SHAFT SEALS - INSTALLATION . 3-102,3-38
AXLE SHAFT SEALS - REMOVAL....3-101,3-37
AXLE SHAFTS - INSTALLATION . . 3-101,3-37,3-65
AXLE SHAFTS - REMOVAL.....3-101,3-37,3-65
AXLE, SPECIAL TOOLS - 8 1/4 ...........3-98
AXLE, SPECIAL TOOLS - FRONT..........3-34
AXLE, SPECIAL TOOLS - REAR...........3-63
AXLE, SPECIFICATIONS - REAR..........3-98
BACK - FRONT - INSTALLATION, SEAT . . . 23-166
BACK - FRONT - REMOVAL, SEAT.......23-166
BACK - REAR - INSTALLATION, SEAT....23-168
BACK - REAR - REMOVAL, SEAT.......23-168
BACK COVER - FRONT - INSTALLATION,
SEAT
.............................23-167
BACK COVER - FRONT - REMOVAL, SEAT
. 23-166
BACK COVER - REAR - INSTALLATION,
SEAT
.............................23-169
BACK COVER - REAR - REMOVAL, SEAT
. 23-169
BACK CUSHION - FRONT -
INSTALLATION, SEAT
.................23-167BACK CUSHION - FRONT - REMOVAL,
SEAT .............................23-167
BACK CUSHION - REAR - INSTALLATION,
SEAT .............................23-170
BACK CUSHION - REAR - REMOVAL,
SEAT .............................23-170
BACK FRAME - REAR - INSTALLATION,
SEAT .............................23-171
BACK FRAME - REAR - REMOVAL, SEAT . 23-171
BACK LATCH / LOCK - INSTALLATION,
FOLDING REAR SEAT................23-170
BACK LATCH / LOCK - REMOVAL,
FOLDING REAR SEAT................23-170
BACK LATCH STRIKER - INSTALLATION,
REAR SEAT........................23-171
BACK LATCH STRIKER - REMOVAL,
REAR SEAT........................23-170
BACK RECLINER - FRONT -
INSTALLATION, SEAT.................23-166
BACK RECLINER - FRONT - REMOVAL,
SEAT .............................23-166
BACKUP LAMP SWITCH - DESCRIPTION . . 8L-15
BACKUP LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-15
BACKUP LAMP SWITCH - OPERATION....8L-15
BAFFLE SEAL - INSTALLATION,
COWL/PLENUM WINDOW.............23-187
BAFFLE SEAL - REMOVAL, COWL/
PLENUM WINDOW..................23-187
BALANCE SHAFT - INSTALLATION........9-74
BALANCE SHAFT - REMOVAL............9-74
BALANCING - STANDARD PROCEDURE,
WHEEL.............................22-4
BALL JOINT - DESCRIPTION, UPPER
SUSPENSION ARM, BUSHINGS..........2-20
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-10
BALL JOINT - INSTALLATION, UPPER.....2-20
BALL JOINT - OPERATION, UPPER
SUSPENSION ARM, BUSHINGS..........2-20
BALL JOINT - REMOVAL, UPPER.........2-20
BAR - INSTALLATION, STABILIZER....2-14,2-19
BAR - REMOVAL, STABILIZER.......2-14,2-19
BAR BUSHINGS - INSTALLATION,
STABILIZER...........................2-9
BAR BUSHINGS - REMOVAL, STABILIZER . . . 2-9
BARRELS - INSTALLATION, PANEL
OUTLET............................24-29
BARRELS - REMOVAL, PANEL OUTLET . . . 24-29
BASE - DESCRIPTION, BRAKES...........5-2
BASE - WARNING, BRAKES..............5-2
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING.............................5-3
BASE BRAKES, SPECIAL TOOLS...........5-7
BASE COAT/CLEAR COAT FINISH -
DESCRIPTION......................23-162
BATTERIES - STANDARD PROCEDURE,
RKE TRANSMITTER...................8N-8
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-8
BATTERY CABLES - DESCRIPTION.......8F-18
BATTERY CABLES - DIAGNOSIS AND
TESTING...........................8F-19
BATTERY CABLES - OPERATION.........8F-18
BATTERY CHARGING - STANDARD
PROCEDURE.........................8F-8
BATTERY HOLDDOWN - DESCRIPTION....8F-17
BATTERY HOLDDOWN - INSTALLATION . . . 8F-17
BATTERY HOLDDOWN - OPERATION.....8F-17
BATTERY HOLDDOWN - REMOVAL.......8F-17
BATTERY SYSTEM - CLEANING...........8F-5
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-6
BATTERY SYSTEM - OPERATION.........8F-2
BATTERY SYSTEM - SPECIAL TOOLS......8F-7
BATTERY SYSTEM - SPECIFICATIONS......8F-6
BATTERY TEMPERATURE SENSOR -
DESCRIPTION.......................8F-24
BATTERY TEMPERATURE SENSOR -
INSTALLATION
.......................8F-24
BATTERY TEMPERATURE SENSOR -
OPERATION
.........................8F-24
BATTERY TEMPERATURE SENSOR -
REMOVAL
..........................8F-24
BATTERY TRAY - DESCRIPTION
.........8F-21
BATTERY TRAY - INSTALLATION
.........8F-21
2 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1743 of 1803
BRAKE CALIPERS - OPERATION, DISC.....5-14
BRAKE CALIPERS - REMOVAL, DISC......5-14
BRAKE COMPONENTS, SPECIFICATIONS....5-6
BRAKE DRUM - DIAGNOSIS AND
TESTING............................5-27
BRAKE DRUM MACHINING - STANDARD
PROCEDURES........................5-27
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-26
BRAKE FLUID, SPECIFICATIONS..........5-27
BRAKE HOSE - INSTALLATION, FRONT.....5-10
BRAKE HOSE - INSTALLATION, REAR......5-10
BRAKE HOSE - REMOVAL, REAR..........5-9
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-13
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-14
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-13
BRAKE LAMP SWITCH - DESCRIPTION . . . 8L-16
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING.......................8L-17
BRAKE LAMP SWITCH - INSTALLATION . . . 8L-18
BRAKE LAMP SWITCH - OPERATION.....8L-16
BRAKE LAMP SWITCH - REMOVAL......8L-17
BRAKE LINE AND HOSES - DIAGNOSIS
AND TESTING.........................5-8
BRAKE LINES - DESCRIPTION............5-8
BRAKE PADS - INSTALLATION, FRONT.....5-11
BRAKE PADS - REMOVAL, FRONT........5-11
BRAKE ROTOR - DIAGNOSIS AND
TESTING, DISC.......................5-18
BRAKE ROTOR - STANDARD
PROCEDURE, DISC....................5-19
BRAKE SHOES - INSTALLATION, DRUM....5-11
BRAKE SHOES - REMOVAL, DRUM.......5-11
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-3
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DESCRIPTION....21-124
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - DIAGNOSIS
AND TESTING......................21-125
BRAKE TRANSMISSION SHIFT
INTERLOCK SYSTEM - OPERATION.....21-125
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION.......................8J-13
BRAKE/PARK BRAKE INDICATOR -
OPERATION.........................8J-13
BRAKES - ABS - DESCRIPTION...........5-32
BRAKES - ABS - OPERATION............5-32
BRAKES - ABS - SPECIFICATIONS........5-33
BRAKES - BASE - DESCRIPTION...........5-2
BRAKES - BASE - WARNING..............5-2
BRAKES, SPECIAL TOOLS - BASE.........5-7
BRAKING SYSTEM - DIAGNOSIS AND
TESTING, ANTILOCK...................5-33
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH............24-12
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-26
BUCKLE - INSTALLATION, REAR SEAT
BELT ..............................8O-35
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-25
BUCKLE - REMOVAL, REAR SEAT BELT . . . 8O-34
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE........................8F-10
BULB - INSTALLATION, ASH RECEIVER
LAMP..............................8L-71
BULB - INSTALLATION, CARGO LAMP....8L-73
BULB - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP................8L-19
BULB - INSTALLATION, COMPASS
MINI-TRIP ILLUMINATION..............8L-75
BULB - INSTALLATION, COURTESY
LAMP..............................8L-76
BULB - INSTALLATION, FRONT FOG
LAMP..............................8L-22
BULB - INSTALLATION, FRONT LAMP....8L-27
BULB - INSTALLATION, FRONT POSITION
LAMP..............................8L-28
BULB - INSTALLATION, HEADLAMP
......8L-32
BULB - INSTALLATION, HEATER-A/C
CONTROL ILLUMINATION
..............8L-78
BULB - INSTALLATION, LICENSE PLATE
LAMP
..............................8L-45
BULB - INSTALLATION, READING LAMP
. . . 8L-79
BULB - INSTALLATION, REAR LAMP
.....8L-59BULB - INSTALLATION, REPEATER LAMP . . 8L-60
BULB - INSTALLATION, TRANSMISSION
RANGE INDICATOR ILLUMINATION.......8L-83
BULB - INSTALLATION, VANITY LAMP....8L-84
BULB - REMOVAL, ASH RECEIVER LAMP . . 8L-71
BULB - REMOVAL, CARGO LAMP........8L-72
BULB - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-18
BULB - REMOVAL, COMPASS MINI-TRIP
ILLUMINATION......................8L-74
BULB - REMOVAL, COURTESY LAMP.....8L-75
BULB - REMOVAL, FRONT FOG LAMP....8L-21
BULB - REMOVAL, FRONT LAMP........8L-26
BULB - REMOVAL, FRONT POSITION
LAMP..............................8L-28
BULB - REMOVAL, HEADLAMP..........8L-31
BULB - REMOVAL, HEATER-A/C
CONTROL ILLUMINATION..............8L-78
BULB - REMOVAL, LICENSE PLATE
LAMP..............................8L-44
BULB - REMOVAL, READING LAMP......8L-79
BULB - REMOVAL, REAR LAMP.........8L-58
BULB - REMOVAL, REPEATER LAMP.....8L-60
BULB - REMOVAL, TRANSMISSION
RANGE INDICATOR ILLUMINATION.......8L-82
BULB - REMOVAL, VANITY LAMP........8L-83
BUMPER - INSTALLATION, JOUNCE.......2-19
BUMPER - REMOVAL, JOUNCE...........2-19
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF................21-125
BUSHING - NV3550 - INSTALLATION,
EXTENSION HOUSING.................21-74
BUSHING - NV3550 - REMOVAL,
EXTENSION HOUSING.................21-73
BUSHINGS - INSTALLATION, STABILIZER
BAR.................................2-9
BUSHINGS - REMOVAL, STABILIZER BAR . . . 2-9
BUSHINGS, AND BALL JOINT -
DESCRIPTION, UPPER SUSPENSION
ARM ...............................2-20
BUSHINGS, AND BALL JOINT -
OPERATION, UPPER SUSPENSION
ARM ...............................2-20
CABLE - ADJUSTMENTS, GEARSHIFT....21-130
CABLE - ADJUSTMENTS, PARK-
INTERLOCK........................21-154
CABLE - DESCRIPTION.................8P-3
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DIAGNOSIS AND TESTING,
ANTENNA BODY......................8A-5
CABLE - DIAGNOSIS AND TESTING,
GEARSHIFT........................21-128
CABLE - INSTALLATION, ANTENNA BODY . . 8A-6
CABLE - INSTALLATION, GEARSHIFT....21-129
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA......................8A-8
CABLE - INSTALLATION, LATCH RELEASE . 23-120
CABLE - INSTALLATION, PARK -
INTERLOCK........................21-153
CABLE - INSTALLATION, THROTTLE
CONTROL..........................14-46
CABLE - OPERATION...................8P-3
CABLE - OPERATION, ANTENNA BODY.....8A-5
CABLE - REMOVAL, ANTENNA BODY......8A-6
CABLE - REMOVAL, GEARSHIFT........21-128
CABLE - REMOVAL, INSTRUMENT PANEL
ANTENNA...........................8A-7
CABLE - REMOVAL, LATCH RELEASE....23-120
CABLE - REMOVAL, PARK - INTERLOCK . 21-153
CABLE - REMOVAL, THROTTLE
CONTROL..........................14-45
CABLE RESISTANCE, 2.4L - SPARK PLUG . . . 8I-3
CABLES - DESCRIPTION, BATTERY.......8F-18
CABLES - DIAGNOSIS AND TESTING,
BATTERY...........................8F-19
CABLES - INSTALLATION...............5-30
CABLES - OPERATION, BATTERY........8F-18
CABLES - REMOVAL...................5-30
CALIBRATION - STANDARD PROCEDURE,
COMPASS...........................8M-2
CALIPER ADAPTER - INSTALLATION,
DISC BRAKE.........................5-18
CALIPER ADAPTER - REMOVAL, DISC
BRAKE
..............................5-18
CALIPERS - ASSEMBLY, DISC BRAKE
......5-16
CALIPERS - CLEANING, DISC BRAKE
......5-16
CALIPERS - DESCRIPTION, DISC BRAKE
. . . 5-13
CALIPERS - DISASSEMBLY, DISC BRAKE
. . . 5-14CALIPERS - INSPECTION, DISC BRAKE....5-16
CALIPERS - INSTALLATION, DISC BRAKE . . . 5-17
CALIPERS - OPERATION, DISC BRAKE.....5-14
CALIPERS - REMOVAL, DISC BRAKE......5-14
CAMBER AND CASTER ADJUSTMENT -
STANDARD PROCEDURE.................2-5
CAMBER, CASTER AND TOE
ADJUSTMENT - STANDARD
PROCEDURE..........................2-5
CAMSHAFT(S) - DESCRIPTION.......9-23,9-33
CAMSHAFT(S) - INSTALLATION......9-25,9-33
CAMSHAFT(S) - REMOVAL..........9-24,9-33
CANISTER - DESCRIPTION, VAPOR......25-33
CANISTER - INSTALLATION, VAPOR......25-33
CANISTER - OPERATION, VAPOR........25-33
CANISTER - REMOVAL, VAPOR..........25-33
CAP - CLEANING, RADIATOR PRESSURE . . . 7-25
CAP - DESCRIPTION, FUEL FILLER.......25-27
CAP - DESCRIPTION, RADIATOR
PRESSURE..........................7-25
CAP - DIAGNOSIS AND TESTING,
RADIATOR PRESSURE.................7-25
CAP - INSPECTION, RADIATOR
PRESSURE..........................7-25
CAP - INSTALLATION, INSTRUMENT
PANEL END........................23-153
CAP - OPERATION, FUEL FILLER........25-27
CAP - OPERATION, RADIATOR
PRESSURE..........................7-25
CAP - REMOVAL, INSTRUMENT PANEL
END ..............................23-153
CAPACITIES - SPECIFICATIONS, FLUID......0-4
CAPACITOR - DESCRIPTION, IGNITION
COIL...............................8I-16
CAPACITOR - INSTALLATION, IGNITION
COIL...............................8I-16
CAPACITOR - OPERATION, IGNITION
COIL...............................8I-16
CAPACITOR - REMOVAL, IGNITION COIL . . . 8I-16
CAPACITY - SPECIFICATIONS, CHARGE . . . 24-42
CAPACITY TEST - DIAGNOSIS AND
TESTING, FUEL PUMP.................14-15
CARDAN UNIVERSAL JOINTS -
ASSEMBLY, SINGLE.....................3-9
CARDAN UNIVERSAL JOINTS -
DISASSEMBLY, SINGLE..................3-8
CARGO LAMP BULB - INSTALLATION.....8L-73
CARGO LAMP BULB - REMOVAL........8L-72
CARGO LAMP SWITCH - INSTALLATION . . 8L-74
CARGO LAMP SWITCH - REMOVAL......8L-73
CARGO LAMP UNIT - INSTALLATION.....8L-74
CARGO LAMP UNIT - REMOVAL.........8L-74
CARPETS AND FLOOR MATS -
INSTALLATION......................23-158
CARPETS AND FLOOR MATS - REMOVAL . 23-158
CASE - NV231 - ASSEMBLY, TRANSFER . . 21-194
CASE - NV231 - CLEANING, TRANSFER . . 21-190
CASE - NV231 - DESCRIPTION,
TRANSFER............................0-3
CASE - NV231 - DESCRIPTION,
TRANSFER.........................21-178
CASE - NV231 - DIAGNOSIS AND
TESTING, TRANSFER.................21-180
CASE - NV231 - DISASSEMBLY,
TRANSFER.........................21-182
CASE - NV231 - INSPECTION, TRANSFER . 21-190
CASE - NV231 - INSTALLATION,
TRANSFER.........................21-205
CASE - NV231 - OPERATION, TRANSFER
. 21-179
CASE - NV231 - REMOVAL, TRANSFER
. . 21-181
CASE - NV242 - ASSEMBLY, TRANSFER
. . 21-230
CASE - NV242 - CLEANING, TRANSFER
. . 21-227
CASE - NV242 - DESCRIPTION,
TRANSFER
............................0-3
CASE - NV242 - DESCRIPTION,
TRANSFER
.........................21-215
CASE - NV242 - DIAGNOSIS AND
TESTING, TRANSFER
.................21-216
CASE - NV242 - DISASSEMBLY,
TRANSFER
.........................21-218
CASE - NV242 - INSPECTION, TRANSFER
. 21-228
CASE - NV242 - INSTALLATION,
TRANSFER
.........................21-243
CASE - NV242 - OPERATION, TRANSFER
. 21-215
CASE - NV242 - REMOVAL, TRANSFER
. . 21-217
CASE BEARINGS - INSTALLATION,
DIFFERENTIAL
...............3-110,3-44,3-79
4 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1744 of 1803
CASE BEARINGS - REMOVAL,
DIFFERENTIAL...............3-110,3-43,3-79
CASE, NV231 - TRANSFER............21-206
CASE, NV242 - TRANSFER............21-244
CASE SKID PLATE - INSTALLATION,
TRANSFER...........................13-7
CASE SKID PLATE - REMOVAL,
TRANSFER...........................13-7
CASE, SPECIFICATIONS - NV242
TRANSFER.........................21-244
CASTER ADJUSTMENT - STANDARD
PROCEDURE, CAMBER..................2-5
CASTER AND TOE ADJUSTMENT -
STANDARD PROCEDURE, CAMBER........2-5
CATALYTIC CONVERTER - DESCRIPTION . . . 11-2
CATALYTIC CONVERTER - INSPECTION....11-3
CATALYTIC CONVERTER - INSTALLATION . . . 11-3
CATALYTIC CONVERTER - REMOVAL......11-2
CAUSES OF BURNT FLUID - DIAGNOSIS
AND TESTING......................21-125
CAUTION - SERVICE CAUTIONS.........24-39
CAUTION, HALF SHAFT.................3-10
CAUTION, REFRIGERANT HOSES/LINES/
TUBES PRECAUTIONS.................24-40
CAUTIONS, CAUTION - SERVICE.........24-39
CD CHANGER - DESCRIPTION...........8A-7
CD CHANGER - INSTALLATION...........8A-7
CD CHANGER - OPERATION.............8A-7
CD CHANGER - REMOVAL..............8A-7
CENTER - DESCRIPTION, POWER
DISTRIBUTION....................8W-97-6
CENTER - OPERATION, POWER
DISTRIBUTION....................8W-97-7
CENTER - REMOVAL, POWER
DISTRIBUTION....................8W-97-7
CENTER ASSEMBLY, ASSEMBLY -
POWER DISTRIBUTION.............8W-97-10
CENTER BEZEL - INSTALLATION,
INSTRUMENT PANEL.................23-154
CENTER BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
CENTER DISASSEMBLY, DISASSEMBLY -
POWER DISTRIBUTION..............8W-97-7
CENTER HIGH MOUNTED STOP LAMP
BULB - INSTALLATION................8L-19
CENTER HIGH MOUNTED STOP LAMP
BULB - REMOVAL....................8L-18
CENTER HIGH MOUNTED STOP LAMP
UNIT - INSTALLATION.................8L-19
CENTER HIGH MOUNTED STOP LAMP
UNIT - REMOVAL....................8L-19
CENTER SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-33
CENTER SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-32
CENTERING - STANDARD PROCEDURE,
CLOCKSPRING......................8O-14
CERTIFICATION LABEL - DESCRIPTION,
VEHICLE SAFETY...................Intro.-9
CHAIN COVER(S) - INSTALLATION,
TIMING BELT.........................9-76
CHAIN COVER(S) - REMOVAL, TIMING
BELT ...............................9-74
CHAIN WEAR, STANDARD PROCEDURE -
MEASURING TIMING...................9-71
CHANGER - DESCRIPTION, CD...........8A-7
CHANGER - INSTALLATION, CD..........8A-7
CHANGER - OPERATION, CD.............8A-7
CHANGER - REMOVAL, CD..............8A-7
CHANNEL - INSTALLATION, GLASS RUN . 23-123,
23-130
CHANNEL - REMOVAL, GLASS RUN....23-123,
23-130
CHARGE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-41
CHARGE CAPACITY - SPECIFICATIONS....24-42
CHARGING - STANDARD PROCEDURE,
BATTERY............................8F-8
CHARGING INDICATOR - DESCRIPTION . . . 8J-15
CHARGING INDICATOR - OPERATION.....8J-15
CHARGING SYSTEM - DESCRIPTION
.....8F-22
CHARGING SYSTEM - DIAGNOSIS AND
TESTING
...........................8F-22
CHARGING SYSTEM - OPERATION
.......8F-22
CHART - DIAGNOSIS AND TESTING,
COOLING SYSTEM DIAGNOSIS
............7-6
CHART, SPECIFICATIONS - TORQUE
.....19-15,
19-19,19-8CHART, SPECIFICATIONS - TORQUE....2-17,2-8
CHECK - STANDARD PROCEDURE, FLUID
LEVEL............................21-126
CHECK - STANDARD PROCEDURE, OIL
PUMP VOLUME.....................21-148
CHECK STRAP - INSTALLATION . . 23-121,23-128,
23-135
CHECK STRAP - REMOVAL.....23-121,23-128,
23-135
CHECK VALVE - DESCRIPTION, FRONT....8R-8
CHECK VALVE - DESCRIPTION, FUEL
TANK ..............................14-28
CHECK VALVE - DESCRIPTION, REAR....8R-34
CHECK VALVE - DESCRIPTION, VACUUM . . 24-28
CHECK VALVE - INSTALLATION, FRONT....8R-9
CHECK VALVE - INSTALLATION, FUEL
TANK ..............................14-28
CHECK VALVE - INSTALLATION, REAR....8R-35
CHECK VALVE - INSTALLATION, VACUUM . 24-28
CHECK VALVE - OPERATION, FRONT......8R-9
CHECK VALVE - OPERATION, FUEL TANK . . 14-28
CHECK VALVE - OPERATION, REAR......8R-34
CHECK VALVE - OPERATION, VACUUM....24-28
CHECK VALVE - REMOVAL, FRONT.......8R-9
CHECK VALVE - REMOVAL, FUEL TANK . . . 14-28
CHECK VALVE - REMOVAL, REAR.......8R-34
CHECK VALVE - REMOVAL, VACUUM.....24-28
CHECKING TRANSMISSION CLUTCH
OPERATION - DIAGNOSIS AND
TESTING, AIR.......................21-80
CHECKS - DIAGNOSIS AND TESTING,
PRELIMINARY.........................7-3
CHILD TETHER ANCHOR - DESCRIPTION . . 8O-13
CHILD TETHER ANCHOR - OPERATION . . . 8O-13
CHIME WARNING SYSTEM -
DESCRIPTION........................8B-1
CHIME WARNING SYSTEM - DIAGNOSIS
AND TESTING........................8B-6
CHIME WARNING SYSTEM - OPERATION . . . 8B-2
CHOKE AND RELAY - DESCRIPTION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - DIAGNOSIS AND
TESTING, AMPLIFIER..................8A-4
CHOKE AND RELAY - INSTALLATION,
AMPLIFIER..........................8A-4
CHOKE AND RELAY - OPERATION,
AMPLIFIER..........................8A-3
CHOKE AND RELAY - REMOVAL,
AMPLIFIER..........................8A-4
CIGAR LIGHTER OUTLET -
DESCRIPTION.....................8W-97-2
CIGAR LIGHTER OUTLET - DIAGNOSIS
AND TESTING.....................8W-97-2
CIGAR LIGHTER OUTLET - OPERATION . 8W-97-2
CLEVIS BRACKET - INSTALLATION........2-13
CLEVIS BRACKET - REMOVAL...........2-13
CLOCKSPRING - DESCRIPTION.........8O-13
CLOCKSPRING - INSTALLATION.........8O-16
CLOCKSPRING - OPERATION...........8O-14
CLOCKSPRING - REMOVAL............8O-15
CLOCKSPRING CENTERING - STANDARD
PROCEDURE........................8O-14
CLUSTER - ASSEMBLY, INSTRUMENT....8J-10
CLUSTER - DESCRIPTION, INSTRUMENT . . . 8J-2
CLUSTER - DIAGNOSIS AND TESTING,
INSTRUMENT........................8J-7
CLUSTER - DISASSEMBLY, INSTRUMENT . . . 8J-9
CLUSTER - INSTALLATION, INSTRUMENT . 8J-11
CLUSTER - OPERATION, INSTRUMENT.....8J-4
CLUSTER - REMOVAL, INSTRUMENT......8J-9
CLUSTER BEZEL - INSTALLATION.......23-147
CLUSTER BEZEL - REMOVAL..........23-147
CLUTCH - ASSEMBLY, LOW/REVERSE
. . . 21-146
CLUTCH - CLEANING, LOW/REVERSE
....21-146
CLUTCH - DESCRIPTION
.................6-1
CLUTCH - DIAGNOSIS AND TESTING
.......6-2
CLUTCH - DISASSEMBLY, LOW/REVERSE
. 21-145
CLUTCH - INSPECTION, A/C
COMPRESSOR
.......................24-14
CLUTCH - INSPECTION, LOW/REVERSE
. . 21-146
CLUTCH - INSTALLATION, A/C
COMPRESSOR
.......................24-14
CLUTCH - OPERATION
..................6-1
CLUTCH - REMOVAL, A/C COMPRESSOR
. . 24-13
CLUTCH - SPECIFICATIONS
...............6-5
CLUTCH - WARNING
....................6-2
CLUTCH ASSEMBLY - ASSEMBLY, INPUT
. 21-138CLUTCH ASSEMBLY - DESCRIPTION,
INPUT............................21-133
CLUTCH ASSEMBLY - DISASSEMBLY,
INPUT............................21-135
CLUTCH ASSEMBLY - OPERATION,
INPUT............................21-135
CLUTCH BREAK-IN - STANDARD
PROCEDURE, A/C COMPRESSOR........24-12
CLUTCH COIL - DIAGNOSIS AND
TESTING, A/C COMPRESSOR...........24-12
CLUTCH DISC - INSTALLATION............6-6
CLUTCH DISC - REMOVAL...............6-6
CLUTCH OPERATION - DIAGNOSIS AND
TESTING, AIR CHECKING
TRANSMISSION......................21-80
CLUTCH PEDAL - INSTALLATION.........6-10
CLUTCH PEDAL - REMOVAL.............6-10
CLUTCH PEDAL POSITION SWITCH -
DESCRIPTION........................6-11
CLUTCH PEDAL POSITION SWITCH -
DIAGNOSIS AND TESTING..............6-11
CLUTCH PEDAL POSITION SWITCH -
OPERATION..........................6-11
CLUTCH RELAY - DESCRIPTION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - DIAGNOSIS AND
TESTING, COMPRESSOR...............24-15
CLUTCH RELAY - INSTALLATION, A/C
COMPRESSOR.......................24-16
CLUTCH RELAY - OPERATION, A/C
COMPRESSOR.......................24-15
CLUTCH RELAY - REMOVAL, A/C
COMPRESSOR........................24-16
CLUTCH RELEASE BEARING -
INSTALLATION.........................6-6
CLUTCH RELEASE BEARING - REMOVAL....6-6
CLUTCH SWITCH OVERRIDE RELAY -
DESCRIPTION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
INSTALLATION........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
OPERATION..........................6-10
CLUTCH SWITCH OVERRIDE RELAY -
REMOVAL...........................6-10
CLUTCHES - DESCRIPTION, HOLDING . . . 21-131
CLUTCHES - OPERATION, HOLDING.....21-132
CMTC LAMP REPLACEMENT -
STANDARD PROCEDURE...............8M-2
COAT FINISH - DESCRIPTION, BASE
COAT/CLEAR.......................23-162
COAT/CLEAR COAT FINISH -
DESCRIPTION, BASE.................23-162
CODE - DESCRIPTION, PAINT..........23-162
CODES - DESCRIPTION, DIAGNOSTIC
TROUBLE............................25-2
CODES - SPECIFICATIONS, PAINT.......23-162
CODES - STANDARD PROCEDURE,
ERASING TRANSMITTER...............8M-8
CODES - STANDARD PROCEDURE,
SETTING TRANSMITTER...............8M-9
COIL - DESCRIPTION, IGNITION..........8I-9
COIL - DIAGNOSIS AND TESTING, A/C
COMPRESSOR CLUTCH...............24-12
COIL - INSTALLATION, IGNITION.........8I-10
COIL - OPERATION, IGNITION............8I-9
COIL - REMOVAL, IGNITION............8I-10
COIL CAPACITOR - DESCRIPTION,
IGNITION...........................8I-16
COIL CAPACITOR - INSTALLATION,
IGNITION...........................8I-16
COIL CAPACITOR - OPERATION,
IGNITION...........................8I-16
COIL CAPACITOR - REMOVAL, IGNITION . . . 8I-16
COIL RESISTANCE, 2.4L - IGNITION
.......8I-2
COIL RESISTANCE, 3.7L V-6 - IGNITION
....8I-3
COLLAPSIBLE SPACER - INSTALLATION
....3-70
COLLAPSIBLE SPACER - REMOVAL
.......3-70
COLUMN - DESCRIPTION
...............19-5
COLUMN - INSTALLATION
...............19-7
COLUMN - REMOVAL
..................19-5
COLUMN, SPECIAL TOOLS - STEERING
....19-8
COMBINATION FLASHER - DESCRIPTION
. . 8L-19
COMBINATION FLASHER - OPERATION
. . . 8L-19
COMBUSTION PRESSURE LEAKAGE -
DIAGNOSIS AND TESTING, CYLINDER
......9-8
COMMUNICATION - DESCRIPTION
........8E-8
COMMUNICATION - OPERATION
..........8E-8
KJINDEX 5
Description Group-Page Description Group-Page Description Group-Page
Page 1747 of 1803
DIFFERENTIAL - TRAC-LOK - CLEANING . . 3-109,
3-77
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY...................3-107,3-75
DIFFERENTIAL - TRAC-LOK -
INSPECTION....................3-109,3-77
DIFFERENTIAL CASE BEARINGS -
INSTALLATION...............3-110,3-44,3-79
DIFFERENTIAL CASE BEARINGS -
REMOVAL..................3-110,3-43,3-79
DIMENSIONS - SPECIFICATIONS, FRAME . . . 13-3
DIMENSIONS - SPECIFICATIONS,
OPENING..........................23-111
DIODE - INSTALLATION............8W-01-14
DIODE - REMOVAL................8W-01-14
DIODE REPLACEMENT - STANDARD
PROCEDURE.........................24-9
DISASSEMBLY - POWER DISTRIBUTION
CENTER DISASSEMBLY.............8W-97-7
DISASSEMBLY, 4C RETAINER/BULKHEAD . 21-122
DISASSEMBLY, DIAGNOSIS AND
TESTING...........................21-83
DISASSEMBLY, DIFFERENTIAL......3-105,3-41
DISASSEMBLY, DIFFERENTIAL -
TRAC-LOK......................3-107,3-75
DISASSEMBLY, DISASSEMBLY - POWER
DISTRIBUTION CENTER.............8W-97-7
DISASSEMBLY, DISC BRAKE CALIPERS....5-14
DISASSEMBLY, HVAC HOUSING.........24-34
DISASSEMBLY, INPUT CLUTCH
ASSEMBLY.........................21-135
DISASSEMBLY, INSTRUMENT CLUSTER....8J-9
DISASSEMBLY, LOW/REVERSE CLUTCH . . 21-145
DISASSEMBLY, MANUAL - NV1500........21-4
DISASSEMBLY, MANUAL - NV3550.......21-35
DISASSEMBLY, OIL PUMP...............9-65
DISASSEMBLY, OIL PUMP.............21-149
DISASSEMBLY, PLANETARY GEARTRAIN . 21-159
DISASSEMBLY, SINGLE CARDAN
UNIVERSAL JOINTS....................3-8
DISASSEMBLY, TRANSFER CASE -
NV231............................21-182
DISASSEMBLY, TRANSFER CASE -
NV242............................21-218
DISASSEMBLY, VALVE BODY...........21-173
DISASSEMBLY, WHEEL CYLINDERS.......5-28
DISC - INSTALLATION, CLUTCH...........6-6
DISC - REMOVAL, CLUTCH...............6-6
DISC BRAKE CALIPER ADAPTER -
INSTALLATION........................5-18
DISC BRAKE CALIPER ADAPTER -
REMOVAL...........................5-18
DISC BRAKE CALIPERS - ASSEMBLY......5-16
DISC BRAKE CALIPERS - CLEANING......5-16
DISC BRAKE CALIPERS - DESCRIPTION....5-13
DISC BRAKE CALIPERS - DISASSEMBLY . . . 5-14
DISC BRAKE CALIPERS - INSPECTION.....5-16
DISC BRAKE CALIPERS - INSTALLATION . . . 5-17
DISC BRAKE CALIPERS - OPERATION.....5-14
DISC BRAKE CALIPERS - REMOVAL.......5-14
DISC BRAKE ROTOR - DIAGNOSIS AND
TESTING............................5-18
DISC BRAKE ROTOR - STANDARD
PROCEDURE.........................5-19
DISCHARGE (ESD) SENSITIVE DEVICES -
STANDARD PROCEDURE,
ELECTROSTATIC...................8W-01-8
DISCHARGE LINE - INSTALLATION, A/C . . . 24-47
DISCHARGE LINE - REMOVAL, A/C.......24-46
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-2
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-6
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-7
DISTRIBUTION CENTER - REMOVAL,
POWER..........................8W-97-7
DISTRIBUTION CENTER ASSEMBLY,
ASSEMBLY - POWER
..............8W-97-10
DISTRIBUTION CENTER DISASSEMBLY,
DISASSEMBLY - POWER
............8W-97-7
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER
...................8W-97-2
DOO - INSTALLATION, FLOOR -
DEFROST
...........................24-37
DOOR - INSTALLATION
.........23-122,23-129DOOR - INSTALLATION, BLEND.........24-35
DOOR - INSTALLATION, PANEL..........24-36
DOOR - INSTALLATION, PASSENGER
AIRBAG............................8O-30
DOOR - INSTALLATION, RECIRC.........24-37
DOOR - REMOVAL.............23-122,23-129
DOOR - REMOVAL, BLEND.............24-35
DOOR - REMOVAL, DEFROST...........24-35
DOOR - REMOVAL, FLOOR - DEFROST....24-36
DOOR - REMOVAL, PASSENGER AIRBAG . . 8O-29
DOOR - REMOVAL, RECIRC............24-37
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-20
DOOR ACTUATOR - INSTALLATION,
FLOOR - DEFROST...................24-25
DOOR ACTUATOR - INSTALLATION,
PANEL.............................24-25
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION.....................24-26
DOOR ACTUATOR - REMOVAL, BLEND....24-20
DOOR ACTUATOR - REMOVAL, FLOOR -
DEFROST...........................24-24
DOOR ACTUATOR - REMOVAL, PANEL....24-24
DOOR ACTUATOR - REMOVAL,
RECIRCULATION.....................24-26
DOOR AJAR INDICATOR - DESCRIPTION . . 8J-17
DOOR AJAR INDICATOR - OPERATION....8J-17
DOOR AJAR SWITCH - DESCRIPTION....8L-77
DOOR AJAR SWITCH - OPERATION........8L-77
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION........................8Q-9
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS AND TESTING.............8Q-10
DOOR CYLINDER LOCK SWITCH -
INSTALLATION......................8Q-10
DOOR CYLINDER LOCK SWITCH -
OPERATION.........................8Q-10
DOOR CYLINDER LOCK SWITCH -
REMOVAL..........................8Q-10
DOOR GLASS - INSTALLATION . . 23-122,23-129,
23-172
DOOR GLASS - REMOVAL......23-122,23-129,
23-172
DOOR LOCK / UNLOCK SWITCH -
INSTALLATION.......................8N-5
DOOR LOCK / UNLOCK SWITCH -
REMOVAL...........................8N-4
DOOR LOCK MOTOR - DESCRIPTION......8N-5
DOOR LOCK MOTOR - DIAGNOSIS AND
TESTING............................8N-5
DOOR LOCK MOTOR - OPERATION.......8N-5
DOOR LOCK RELAY - DESCRIPTION......8N-6
DOOR LOCK RELAY - DIAGNOSIS AND
TESTING............................8N-6
DOOR LOCK RELAY - INSTALLATION......8N-7
DOOR LOCK RELAY - OPERATION........8N-6
DOOR LOCK RELAY - REMOVAL.........8N-6
DOOR LOCK/UNLOCK SWITCH -
DIAGNOSIS AND TESTING..............8N-4
DOOR LOWER WEATHERSTRIP -
INSTALLATION......................23-186
DOOR LOWER WEATHERSTRIP -
REMOVAL.........................23-186
DOOR OUTER BELT MOLDING -
INSTALLATION, FRONT...............23-186
DOOR OUTER BELT MOLDING -
INSTALLATION, REAR................23-186
DOOR OUTER BELT MOLDING -
REMOVAL, FRONT...................23-186
DOOR OUTER BELT MOLDING -
REMOVAL, REAR....................23-186
DOOR PRIMARY WEATHERSTRIP -
INSTALLATION......................23-185
DOOR PRIMARY WEATHERSTRIP -
REMOVAL.........................23-185
DOOR SCUFF PLATE - INSTALLATION,
REAR.............................23-160
DOOR SCUFF PLATE - REMOVAL, REAR . . 23-160
DOOR SILL SCUFF PLATE -
INSTALLATION......................23-157
DOOR SILL SCUFF PLATE - REMOVAL
. . . 23-157
DOOR/HOUSING - INSTALLATION, FUEL
FILL
..............................23-141
DOOR/HOUSING - REMOVAL, FUEL FILL
. 23-141
DOUBLE INVERTED FLARING -
STANDARD PROCEDURE
.................5-8
DRAIN AND FILL - STANDARD
PROCEDURE, FLUID
...........21-208,21-246DRAIN TUBE - INSTALLATION..........23-181
DRAIN TUBE - REMOVAL.............23-180
DRAINAGE AND WIND NOISE
DIAGNOSIS, DIAGNOSIS AND TESTING
- WATER ..........................23-176
DRAINING COOLING SYSTEM 3.7L
ENGINE - STANDARD PROCEDURE........7-12
DRAW TEST - STANDARD PROCEDURE,
IGNITION-OFF.......................8F-14
DRIVE - DIAGNOSIS AND TESTING,
VISCOUS FAN........................7-28
DRIVE BELT - DIAGNOSIS AND TESTING,
SERPENTINE.........................7-15
DRIVE MOTOR - INSTALLATION........23-182
DRIVE MOTOR - REMOVAL............23-182
DRIVER AIRBAG - DESCRIPTION........8O-17
DRIVER AIRBAG - INSTALLATION.......8O-20
DRIVER AIRBAG - OPERATION..........8O-18
DRIVER AIRBAG - REMOVAL...........8O-19
DRIVER SEAT HEATER SWITCH -
DESCRIPTION.......................8G-11
DRIVER SEAT HEATER SWITCH -
INSTALLATION......................8G-13
DRIVER SEAT HEATER SWITCH -
OPERATION.........................8G-12
DRIVER SEAT HEATER SWITCH -
REMOVAL..........................8G-13
DRIVER SIDE BEZELS - INSTALLATION,
INSTRUMENT PANEL.................23-154
DRIVER SIDE BEZELS - REMOVAL,
INSTRUMENT PANEL.................23-153
DROP - STANDARD PROCEDURE,
TESTING FOR A VOLTAGE...........8W-01-10
DRUM - DIAGNOSIS AND TESTING,
BRAKE..............................5-27
DRUM BRAKE - ADJUSTMENT, REAR......5-12
DRUM BRAKE - DESCRIPTION, REAR.....5-10
DRUM BRAKE - OPERATION, REAR.......5-11
DRUM BRAKE SHOES - INSTALLATION....5-11
DRUM BRAKE SHOES - REMOVAL........5-11
DRUM MACHINING - STANDARD
PROCEDURES, BRAKE.................5-27
DUCT - INSTALLATION, DEFROST/
DEMISTER..........................24-32
DUCT - INSTALLATION, FLOOR..........24-32
DUCT - INSTALLATION, FLOOR CONSOLE . 24-31
DUCT - REMOVAL, FLOOR.............24-32
DUCT - REMOVAL, FLOOR CONSOLE.....24-31
DUCT/DEMISTER ADAPTOR - REMOVAL,
DEFROST...........................24-32
EFFECTS OF INCORRECT FLUID LEVEL -
DIAGNOSIS AND TESTING............21-125
ELECTRIC - DESCRIPTION, RADIATOR
FAN ................................7-26
ELECTRIC - INSTALLATION, RADIATOR
FAN ................................7-27
ELECTRIC - INSTALLATION, WINDOW
REGULATOR.................23-126,23-134
ELECTRIC - OPERATION, RADIATOR FAN . . . 7-26
ELECTRIC - REMOVAL, RADIATOR FAN....7-26
ELECTRIC - REMOVAL, WINDOW
REGULATOR.................23-126,23-134
ELECTRICAL - DESCRIPTION............5-34
ELECTRICAL - OPERATION..............5-34
ELECTRICAL TESTER - STANDARD
PROCEDURE, USING MIDTRONICS.......8F-15
ELECTROSTATIC DISCHARGE (ESD)
SENSITIVE DEVICES - STANDARD
PROCEDURE......................8W-01-8
ELEMENT - DESCRIPTION, HEATED SEAT . 8G-13
ELEMENT - DIAGNOSIS AND TESTING,
HEATED SEAT .......................8G-13
ELEMENT - OPERATION, HEATED SEAT . . . 8G-13
EMISSION CONTROL INFORMATION
(VECI) LABEL - DESCRIPTION,
VEHICLE..........................Intro.-8
EMISSION CONTROL SYSTEM -
DESCRIPTION........................25-1
END - INSTALLATION, TIE ROD.........19-16
END - REMOVAL, TIE ROD.............19-16
END CAP - INSTALLATION, INSTRUMENT
PANEL
............................23-153
END CAP - REMOVAL, INSTRUMENT
PANEL
............................23-153
END REMOVAL TOOL, SPECIAL TOOLS -
OUTER TIE ROD
.....................19-15
ENGINE - 3.7L - DESCRIPTION
............9-3
ENGINE - DESCRIPTION, 3.7L
............7-21
8 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1756 of 1803
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-35
MOTOR - OPERATION, REAR WIPER.....8R-41
MOTOR - REMOVAL, BLOWER..........24-30
MOTOR - REMOVAL, DRIVE...........23-182
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-36
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-36
MOTOR - REMOVAL, REAR WIPER......8R-42
MOTOR - REMOVAL, STARTER..........8F-39
MOTOR - REMOVAL, WINDOW..........8N-22
MOTOR, GAS POWERED - STARTER......8F-39
MOTOR RELAY - DESCRIPTION,
BLOWER...........................24-20
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-41
MOTOR RELAY - DIAGNOSIS AND
TESTING, BLOWER...................24-21
MOTOR RELAY - INSTALLATION,
BLOWER...........................24-22
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-43
MOTOR RELAY - OPERATION, BLOWER . . . 24-20
MOTOR RELAY - OPERATION, STARTER . . . 8F-42
MOTOR RELAY - REMOVAL, BLOWER....24-21
MOTOR RELAY - REMOVAL, STARTER....8F-43
MOTOR RESISTOR - DESCRIPTION,
BLOWER...........................24-22
MOTOR RESISTOR - DIAGNOSIS AND
TESTING, BLOWER.....................24-22
MOTOR RESISTOR - INSTALLATION,
BLOWER...........................24-22
MOTOR RESISTOR - OPERATION,
BLOWER...........................24-22
MOTOR RESISTOR - REMOVAL,
BLOWER...........................24-22
MOTOR SWITCH - DESCRIPTION,
BLOWER...........................24-23
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER...................24-23
MOTOR SWITCH - INSTALLATION,
BLOWER...........................24-23
MOTOR SWITCH - OPERATION, BLOWER . . 24-23
MOTOR SWITCH - REMOVAL, BLOWER . . . 24-23
MOUNT - INSTALLATION, FRONT.........9-57
MOUNT - INSTALLATION, REAR..........9-57
MOUNT - REMOVAL, FRONT.............9-56
MOUNT - REMOVAL, REAR..............9-57
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH..............8L-18
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-19
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-3
MOUNTING - STANDARD PROCEDURE,
WHEEL............................22-10
MOUNTING BRACKET - INSTALLATION,
PASSENGER AIRBAG.................8O-31
MOUNTING BRACKET - REMOVAL,
PASSENGER AIRBAG.................8O-31
MUFFLER - DESCRIPTION...............11-4
MUFFLER - INSTALLATION
..............11-5
MUFFLER - REMOVAL
..................11-5
MULTI-FUNCTION SWITCH -
DESCRIPTION
.......................8L-46
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING
.......................8L-50
MULTI-FUNCTION SWITCH -
INSTALLATION
.......................8L-53
MULTI-FUNCTION SWITCH - OPERATION
. . 8L-48
MULTI-FUNCTION SWITCH - REMOVAL
. . . 8L-53
NAME PLATES - INSTALLATION,
EXTERIOR
.........................23-141
NAME PLATES - REMOVAL, EXTERIOR
. . . 23-140
NOISE - DIAGNOSIS AND TESTING, A/C
COMPRESSOR
.......................24-42
NOISE - DIAGNOSIS AND TESTING,
WIND
...............................23-3
NOISE DIAGNOSIS, DIAGNOSIS AND
TESTING - WATER DRAINAGE AND
WIND
.............................23-176
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE
.......................22-8NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-9
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-11
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO..................8A-10
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO....................8A-10
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
DESCRIPTION.......................25-20
NOZZLE - DESCRIPTION, FRONT
WASHER...........................8R-11
NOZZLE - DESCRIPTION, REAR WASHER . 8R-36
NOZZLE - INSTALLATION, FRONT
WASHER...........................8R-11
NOZZLE - INSTALLATION, REAR
WASHER...........................8R-37
NOZZLE - OPERATION, FRONT WASHER . . 8R-11
NOZZLE - OPERATION, REAR WASHER . . . 8R-36
NOZZLE - REMOVAL, FRONT WASHER....8R-11
NOZZLE - REMOVAL, REAR WASHER....8R-36
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-8
NV1500 - ASSEMBLY, MANUAL.........21-13
NV1500 - CLEANING, MANUAL..........21-10
NV1500 - DESCRIPTION, MANUAL........21-1
NV1500 - DISASSEMBLY, MANUAL........21-4
NV1500 - INSPECTION, MANUAL..........21-11
NV1500 - INSTALLATION, EXTENSION
HOUSING SEAL......................21-32
NV1500 - INSTALLATION, MANUAL......21-29
NV1500 - MANUAL...................21-30
NV1500 - OPERATION, MANUAL..........21-1
NV1500 - REMOVAL, EXTENSION
HOUSING SEAL......................21-32
NV1500 - REMOVAL, MANUAL...........21-3
NV1500 - SPECIFICATIONS.............21-30
NV231 - ASSEMBLY, TRANSFER CASE . . . 21-194
NV231 - CLEANING, TRANSFER CASE . . . 21-190
NV231 - DESCRIPTION, TRANSFER CASE . . . 0-3
NV231 - DESCRIPTION, TRANSFER CASE . 21-178
NV231 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-180
NV231 - DISASSEMBLY, TRANSFER
CASE.............................21-182
NV231 - INSPECTION, TRANSFER CASE . . 21-190
NV231 - INSTALLATION, TRANSFER
CASE.............................21-205
NV231 - OPERATION, TRANSFER CASE . . 21-179
NV231 - REMOVAL, TRANSFER CASE....21-181
NV231 - TRANSFER CASE.............21-206
NV242 - ASSEMBLY, TRANSFER CASE . . . 21-230
NV242 - CLEANING, TRANSFER CASE . . . 21-227
NV242 - DESCRIPTION, TRANSFER CASE . . . 0-3
NV242 - DESCRIPTION, TRANSFER CASE . 21-215
NV242 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-216
NV242 - DISASSEMBLY, TRANSFER
CASE.............................21-218
NV242 - INSPECTION, TRANSFER CASE . . 21-228
NV242 - INSTALLATION, TRANSFER
CASE.............................21-243
NV242 - OPERATION, TRANSFER CASE . . 21-215
NV242 - REMOVAL, TRANSFER CASE....21-217
NV242 - TRANSFER CASE.............21-244
NV242 TRANSFER CASE,
SPECIFICATIONS....................21-244
NV3550 - ASSEMBLY, MANUAL.........21-48
NV3550 - CLEANING, MANUAL..........21-46
NV3550 - DESCRIPTION, MANUAL.......21-33
NV3550 - DISASSEMBLY, MANUAL.......21-35
NV3550 - INSPECTION, MANUAL........21-46
NV3550 - INSTALLATION, EXTENSION
HOUSING BUSHING...................21-74
NV3550 - INSTALLATION, EXTENSION
HOUSING SEAL......................21-74
NV3550 - INSTALLATION, MANUAL......21-70
NV3550 - MANUAL...................21-71
NV3550 - OPERATION, MANUAL
.........21-33
NV3550 - REMOVAL, EXTENSION
HOUSING BUSHING
...................21-73
NV3550 - REMOVAL, EXTENSION
HOUSING SEAL
......................21-74
NV3550 - REMOVAL, MANUAL
..........21-34
ODOMETER - DESCRIPTION
............8J-25ODOMETER - OPERATION..............8J-25
OFF INDICATOR - DESCRIPTION,
OVERDRIVE.........................8J-26
OFF INDICATOR - OPERATION,
OVERDRIVE.........................8J-26
OIL - DESCRIPTION, REFRIGERANT......24-53
OIL - OPERATION, REFRIGERANT........24-54
OIL - STANDARD PROCEDURE, ENGINE....9-61
OIL FILTER - INSTALLATION.............9-63
OIL FILTER - REMOVAL.................9-63
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.............9-10
OIL LEAK - DIAGNOSIS AND TESTING,
ENGINE.............................9-60
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-54
OIL PAN - CLEANING..................9-63
OIL PAN - DESCRIPTION................9-63
OIL PAN - INSPECTION.................9-63
OIL PAN - INSTALLATION...............9-64
OIL PAN - REMOVAL...................9-63
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE.....................9-60
OIL PRESSURE INDICATOR -
DESCRIPTION, LOW..................8J-23
OIL PRESSURE INDICATOR -
OPERATION, LOW....................8J-23
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-65
OIL PRESSURE SENSOR/SWITCH -
INSTALLATION........................9-65
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-65
OIL PRESSURE SENSOR/SWITCH -
REMOVAL...........................9-65
OIL PUMP - ASSEMBLY................9-67
OIL PUMP - ASSEMBLY..............21-151
OIL PUMP - CLEANING...............21-150
OIL PUMP - DESCRIPTION............21-147
OIL PUMP - DISASSEMBLY.............9-65
OIL PUMP - DISASSEMBLY............21-149
OIL PUMP - INSPECTION...............9-66
OIL PUMP - INSPECTION.............21-150
OIL PUMP - INSTALLATION.............9-67
OIL PUMP - OPERATION..............21-147
OIL PUMP - REMOVAL.................9-65
OIL PUMP FRONT SEAL - INSTALLATION . 21-152
OIL PUMP FRONT SEAL - REMOVAL....21-152
OIL PUMP VOLUME CHECK - STANDARD
PROCEDURE.......................21-148
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT........................9-47
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT........................9-46
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT........................9-48
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT........................9-48
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-3
ON/OFF RELAY - DESCRIPTION, WIPER . . . 8R-25
ON/OFF RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-26
ON/OFF RELAY - INSTALLATION, WIPER . . 8R-26
ON/OFF RELAY - OPERATION, WIPER....8R-25
ON/OFF RELAY - REMOVAL, WIPER......8R-26
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-12
OPENING DIMENSIONS -
SPECIFICATIONS....................23-111
OPENING FLARE MOLDINGS -
INSTALLATION, FRONT WHEEL.........23-145
OPENING FLARE MOLDINGS -
INSTALLATION, REAR WHEEL..........23-145
OPENING FLARE MOLDINGS -
REMOVAL, FRONT WHEEL............23-145
OPENING FLARE MOLDINGS -
REMOVAL, REAR WHEEL.............23-145
OPENING REINFORCEMENT -
INSTALLATION, GRILLE...............23-142
OPENING REINFORCEMENT - REMOVAL,
GRILLE
...........................23-142
OPENING TRIM LACE - INSTALLATION
. . . 23-180
OPENING TRIM LACE - REMOVAL
......23-180
OPENING WEATHERSTRIP -
INSTALLATION, SWING GATE
..........23-186
OPENING WEATHERSTRIP - REMOVAL,
SWING GATE
.......................23-186
KJINDEX 17
Description Group-Page Description Group-Page Description Group-Page
Page 1757 of 1803
OPERATION - DESCRIPTION, MODES OF . . 8E-11
OPERATION - DIAGNOSIS AND TESTING,
AIR CHECKING TRANSMISSION
CLUTCH............................21-80
ORDER, 2.4L 4-CYLINDER - ENGINE
FIRING..............................8I-2
ORDER, 3.7L V-6 - ENGINE FIRING........8I-2
ORIFICE TUBE - DESCRIPTION, A/C......24-50
ORIFICE TUBE - INSTALLATION, A/C......24-50
ORIFICE TUBE - OPERATION, A/C........24-50
ORIFICE TUBE - REMOVAL, A/C.........24-50
ORVR - DESCRIPTION.................25-29
ORVR - OPERATION..................25-29
OUT - ADJUSTMENT, LOCK..............5-30
OUTBOARD SEAT BELT & RETRACTOR -
INSTALLATION, REAR.................8O-34
OUTBOARD SEAT BELT & RETRACTOR -
REMOVAL, REAR....................8O-33
OUTER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-186
OUTER BELT MOLDING - INSTALLATION,
REAR DOOR.......................23-186
OUTER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-186
OUTER BELT MOLDING - REMOVAL,
REAR DOOR.......................23-186
OUTER TIE ROD END REMOVAL TOOL,
SPECIAL TOOLS.....................19-15
OUTLET - DESCRIPTION, CIGAR
LIGHTER.........................8W-97-2
OUTLET - DESCRIPTION, POWER......8W-97-11
OUTLET - DIAGNOSIS AND TESTING,
CIGAR LIGHTER...................8W-97-2
OUTLET - DIAGNOSIS AND TESTING,
POWER.........................8W-97-11
OUTLET - INSTALLATION, POWER....8W-97-13
OUTLET - OPERATION, CIGAR LIGHTER . 8W-97-2
OUTLET - OPERATION, POWER......8W-97-11
OUTLET - REMOVAL, POWER........8W-97-12
OUTLET BARRELS - INSTALLATION,
PANEL.............................24-29
OUTLET BARRELS - REMOVAL, PANEL . . . 24-29
OUTLETS - DESCRIPTION, DEMISTER....24-29
OUTPUT - DESCRIPTION, PCM...........8I-4
OUTPUT - OPERATION, PCM............14-33
OUTPUT - OPERATION, PCM.............8I-4
OUTPUT SHAFT SEAL - INSTALLATION,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - INSTALLATION,
REAR.............................21-212
OUTPUT SHAFT SEAL - REMOVAL,
FRONT......................21-208,21-246
OUTPUT SHAFT SEAL - REMOVAL, REAR . 21-210
OUTPUT SPEED SENSOR - DESCRIPTION . 21-152
OUTPUT SPEED SENSOR -
INSTALLATION......................21-152
OUTPUT SPEED SENSOR - OPERATION . . 21-152
OUTPUT SPEED SENSOR - REMOVAL . . . 21-152
OVERDRIVE OFF INDICATOR -
DESCRIPTION.......................8J-26
OVERDRIVE OFF INDICATOR -
OPERATION.........................8J-26
OVERDRIVE SWITCH - DESCRIPTION....21-153
OVERDRIVE SWITCH - OPERATION.....21-153
OVERHEAD CONSOLE - DESCRIPTION....8M-1
OVERHEAD CONSOLE - OPERATION......8M-2
OVERHEAD CONSOLE, REMOVAL........8M-4
OVERRIDE RELAY - DESCRIPTION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - INSTALLATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - OPERATION,
CLUTCH SWITCH......................6-10
OVERRIDE RELAY - REMOVAL, CLUTCH
SWITCH.............................6-10
OXYGEN SENSOR - DESCRIPTION.......14-40
OXYGEN SENSOR - INSTALLATION.......14-43
OXYGEN SENSOR - OPERATION.........14-40
OXYGEN SENSOR - REMOVAL..........14-41
PADS - INSTALLATION, FRONT BRAKE.....5-11
PADS - REMOVAL, FRONT BRAKE........5-11
PAINT CODE - DESCRIPTION..........23-162
PAINT CODES - SPECIFICATIONS.......23-162
PAINT TOUCH-UP - DESCRIPTION
......23-163
PAN - CLEANING, OIL
..................9-63
PAN - DESCRIPTION, OIL
...............9-63
PAN - INSPECTION, OIL
................9-63
PAN - INSTALLATION, OIL
...............9-64PAN - REMOVAL, OIL..................9-63
PANEL - DESCRIPTION, LATCH - ACCESS . 23-139
PANEL - INSTALLATION, GLASS........23-178
PANEL - INSTALLATION, LATCH -
ACCESS...........................23-139
PANEL - INSTALLATION, QUARTER TRIM . 23-159
PANEL - INSTALLATION, TRIM . . . 23-126,23-132,
23-138
PANEL - REMOVAL, GLASS............23-178
PANEL - REMOVAL, LATCH - ACCESS . . . 23-139
PANEL - REMOVAL, QUARTER TRIM....23-159
PANEL - REMOVAL, TRIM . 23-125,23-132,23-138
PANEL ADJUSTMENT, ADJUSTMENTS -
SUNROOF GLASS...................23-178
PANEL ANTENNA CABLE -
INSTALLATION, INSTRUMENT............8A-8
PANEL ANTENNA CABLE - REMOVAL,
INSTRUMENT........................8A-7
PANEL ASSEMBLY - INSTALLATION,
INSTRUMENT......................23-151
PANEL ASSEMBLY - REMOVAL,
INSTRUMENT......................23-149
PANEL CENTER BEZEL - INSTALLATION,
INSTRUMENT......................23-154
PANEL CENTER BEZEL - REMOVAL,
INSTRUMENT......................23-154
PANEL DOOR - INSTALLATION..........24-36
PANEL DOOR ACTUATOR -
INSTALLATION.......................24-25
PANEL DOOR ACTUATOR - REMOVAL....24-24
PANEL DRIVER SIDE BEZELS -
INSTALLATION, INSTRUMENT..........23-154
PANEL DRIVER SIDE BEZELS -
REMOVAL, INSTRUMENT.............23-153
PANEL END CAP - INSTALLATION,
INSTRUMENT......................23-153
PANEL END CAP - REMOVAL,
INSTRUMENT......................23-153
PANEL OUTLET BARRELS -
INSTALLATION.......................24-29
PANEL OUTLET BARRELS - REMOVAL....24-29
PANEL PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT..........23-154
PANEL PASSENGER SIDE BEZEL -
REMOVAL, INSTRUMENT.............23-154
PANEL SEAL - INSTALLATION, GLASS . . . 23-178
PANEL SEAL - REMOVAL, GLASS.......23-178
PANEL TOP COVER - INSTALLATION,
INSTRUMENT......................23-153
PANEL TOP COVER - REMOVAL,
INSTRUMENT......................23-152
PARK - INTERLOCK CABLE -
INSTALLATION......................21-153
PARK - INTERLOCK CABLE - REMOVAL . . 21-153
PARK LAMP RELAY - DESCRIPTION......8L-54
PARK LAMP RELAY - DIAGNOSIS AND
TESTING...........................8L-55
PARK LAMP RELAY - INSTALLATION.....8L-56
PARK LAMP RELAY - OPERATION.......8L-54
PARK LAMP RELAY - REMOVAL.........8L-55
PARK RAMP - INSTALLATION, WIPER
ARM ..............................8R-43
PARK RAMP - REMOVAL, WIPER ARM . . . 8R-43
PARKING BRAKE - DESCRIPTION.........5-29
PARKING BRAKE - OPERATION...........5-29
PARK-INTERLOCK CABLE -
ADJUSTMENTS.....................21-154
PART TIME INDICATOR - DESCRIPTION . . . 8J-29
PART TIME INDICATOR - OPERATION.....8J-29
PASSENGER AIRBAG - DESCRIPTION....8O-27
PASSENGER AIRBAG - INSTALLATION....8O-29
PASSENGER AIRBAG - OPERATION......8O-27
PASSENGER AIRBAG - REMOVAL........8O-28
PASSENGER AIRBAG DOOR -
INSTALLATION......................8O-30
PASSENGER AIRBAG DOOR - REMOVAL . . 8O-29
PASSENGER AIRBAG MOUNTING
BRACKET - INSTALLATION.............8O-31
PASSENGER AIRBAG MOUNTING
BRACKET - REMOVAL
.................8O-31
PASSENGER SEAT HEATER SWITCH -
DESCRIPTION
.......................8G-14
PASSENGER SEAT HEATER SWITCH -
INSTALLATION
......................8G-15
PASSENGER SEAT HEATER SWITCH -
OPERATION
.........................8G-14
PASSENGER SEAT HEATER SWITCH -
REMOVAL
..........................8G-15PASSENGER SIDE BEZEL -
INSTALLATION, INSTRUMENT PANEL....23-154
PASSENGER SIDE BEZEL - REMOVAL,
INSTRUMENT PANEL.................23-154
PATTERNS - DIAGNOSIS AND TESTING,
TIRE WEAR..........................22-8
PCM - DESCRIPTION..................8E-11
PCM - OPERATION...................8E-14
PCM INPUT - OPERATION, ASD SENSE.....8I-4
PCM OUTPUT - DESCRIPTION............8I-4
PCM OUTPUT - OPERATION............14-33
PCM OUTPUT - OPERATION.............8I-4
PCM/SKIM PROGRAMMING - STANDARD
PROCEDURE.........................8E-1
PCV VALVE - DESCRIPTION............25-29
PCV VALVE - DIAGNOSIS AND TESTING . . . 25-31
PCV VALVE - INSTALLATION............25-32
PCV VALVE - OPERATION..............25-31
PCV VALVE - REMOVAL...............25-32
PEDAL - DESCRIPTION.................5-20
PEDAL - INSTALLATION................5-20
PEDAL - INSTALLATION, ACCELERATOR . . . 14-30
PEDAL - INSTALLATION, CLUTCH.........6-10
PEDAL - OPERATION...................5-20
PEDAL - REMOVAL....................5-20
PEDAL - REMOVAL, ACCELERATOR......14-29
PEDAL - REMOVAL, CLUTCH............6-10
PEDAL POSITION SWITCH -
DESCRIPTION, CLUTCH.................6-11
PEDAL POSITION SWITCH - DIAGNOSIS
AND TESTING, CLUTCH.................6-11
PEDAL POSITION SWITCH - OPERATION,
CLUTCH.............................6-11
PERFORMANCE - DIAGNOSIS AND
TESTING, A/C........................24-2
PERFORMANCE - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS............9-4
PERFORMANCE - DIAGNOSIS AND
TESTING, HEATER.....................24-6
PILOT BEARING - INSTALLATION..........6-8
PILOT BEARING - REMOVAL..............6-8
PINION GEAR/RING GEAR -
INSTALLATION........................3-46
PINION GEAR/RING GEAR - REMOVAL.....3-44
PINION GEAR/RING GEAR/TONE RING -
INSTALLATION...................3-112,3-82
PINION GEAR/RING GEAR/TONE RING -
REMOVAL......................3-110,3-79
PINION SEAL - INSTALLATION . . 3-103,3-39,3-68
PINION SEAL - REMOVAL......3-102,3-38,3-68
PIPE - INSTALLATION, CROSS-OVER......11-3
PIPE - REMOVAL, CROSS-OVER..........11-3
PISTON & CONNECTING ROD -
DESCRIPTION........................9-49
PISTON FITTING - STANDARD
PROCEDURE.........................9-50
PISTON RING FITTING - STANDARD
PROCEDURE.........................9-52
PISTONS - DESCRIPTION.............21-155
PISTONS - OPERATION...............21-155
PLANETARY GEARTRAIN - ASSEMBLY . . . 21-160
PLANETARY GEARTRAIN - CLEANING....21-159
PLANETARY GEARTRAIN - DESCRIPTION . 21-157
PLANETARY GEARTRAIN -
DISASSEMBLY......................21-159
PLANETARY GEARTRAIN - INSPECTION . . 21-159
PLANETARY GEARTRAIN - OPERATION . . 21-157
PLATE - INSTALLATION, DOOR SILL
SCUFF............................23-157
PLATE - INSTALLATION, FLEX............9-49
PLATE - INSTALLATION, FRONT SKID......13-6
PLATE - INSTALLATION, FUEL TANK
SKID...............................13-9
PLATE - INSTALLATION, REAR DOOR
SCUFF............................23-160
PLATE - INSTALLATION, TRANSFER
CASE SKID..........................13-7
PLATE - REMOVAL, DOOR SILL SCUFF . . . 23-157
PLATE - REMOVAL, FLEX...............9-49
PLATE - REMOVAL, FRONT SKID.........13-6
PLATE - REMOVAL, FUEL TANK SKID
......13-9
PLATE - REMOVAL, REAR DOOR SCUFF
. . 23-160
PLATE - REMOVAL, TRANSFER CASE
SKID
...............................13-7
PLATE LAMP BULB - INSTALLATION,
LICENSE
...........................8L-45
PLATE LAMP BULB - REMOVAL,
LICENSE
...........................8L-44
18 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1763 of 1803
SENSOR - INSTALLATION, OXYGEN......14-43
SENSOR - INSTALLATION, POSITION....21-210,
21-247
SENSOR - INSTALLATION, REAR WHEEL
SPEED..............................5-35
SENSOR - INSTALLATION, THROTTLE
POSITION..........................14-48
SENSOR - OPERATION, AMBIENT TEMP . . . 8M-9
SENSOR - OPERATION, BATTERY
TEMPERATURE......................8F-24
SENSOR - OPERATION, CRANKSHAFT
POSITION..........................14-31
SENSOR - OPERATION, ENGINE
COOLANT TEMPERATURE...............7-20
SENSOR - OPERATION, FRONT IMPACT . . . 8O-21
SENSOR - OPERATION, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - OPERATION, INPUT SPEED . . . 21-143
SENSOR - OPERATION, INTAKE AIR
TEMPERATURE......................14-36
SENSOR - OPERATION, KNOCK..........8I-11
SENSOR - OPERATION, LINE PRESSURE
(LP)..............................21-144
SENSOR - OPERATION, MAP...........14-38
SENSOR - OPERATION, OUTPUT SPEED . . 21-152
SENSOR - OPERATION, OXYGEN........14-40
SENSOR - OPERATION, POSITION......21-209,
21-247
SENSOR - OPERATION, THROTTLE
POSITION..........................14-47
SENSOR - OPERATION, TRANSMISSION
RANGE............................21-168
SENSOR - OPERATION, TRANSMISSION
TEMPERATURE.....................21-170
SENSOR - REMOVAL, BATTERY
TEMPERATURE......................8F-24
SENSOR - REMOVAL, CRANKSHAFT
POSITION..........................14-31
SENSOR - REMOVAL, ENGINE COOLANT
TEMPERATURE.......................7-20
SENSOR - REMOVAL, FRONT IMPACT....8O-22
SENSOR - REMOVAL, FRONT WHEEL
SPEED..............................5-34
SENSOR - REMOVAL, FUEL LEVEL
SENDING UNIT.......................14-9
SENSOR - REMOVAL, INPUT SPEED.....21-143
SENSOR - REMOVAL, INTAKE AIR
TEMPERATURE......................14-37
SENSOR - REMOVAL, KNOCK...........8I-12
SENSOR - REMOVAL, LINE PRESSURE
(LP)..............................21-144
SENSOR - REMOVAL, MAP.............14-39
SENSOR - REMOVAL, OUTPUT SPEED . . . 21-152
SENSOR - REMOVAL, OXYGEN..........14-41
SENSOR - REMOVAL, POSITION . . 21-210,21-247
SENSOR - REMOVAL, REAR WHEEL
SPEED..............................5-35
SENSOR - REMOVAL, THROTTLE
POSITION..........................14-47
SENSOR CIRCUIT - DIAGNOSIS AND
TESTING, AMBIENT TEMPERATURE.......8M-9
SENSOR RETURN - DESCRIPTION.......8E-14
SENSOR/SWITCH - DESCRIPTION, OIL
PRESSURE..........................9-65
SENSOR/SWITCH - INSTALLATION, OIL
PRESSURE
..........................9-65
SENSOR/SWITCH - OPERATION, OIL
PRESSURE
..........................9-65
SENSOR/SWITCH - REMOVAL, OIL
PRESSURE
..........................9-65
SENTRY KEY IMMOBILIZER MODULE -
DESCRIPTION
.......................8E-15
SENTRY KEY IMMOBILIZER MODULE -
INSTALLATION
.......................8E-18
SENTRY KEY IMMOBILIZER MODULE -
OPERATION
.........................8E-16
SENTRY KEY IMMOBILIZER MODULE -
REMOVAL
..........................8E-17
SENTRY KEY TRANSPONDER
PROGRAMMING - STANDARD
PROCEDURE
.........................8Q-8
SERPENTINE DRIVE BELT - DIAGNOSIS
AND TESTING
........................7-15
SERVO - DESCRIPTION
.................8P-4
SERVO - INSTALLATION
................8P-5
SERVO - OPERATION
..................8P-4
SERVO - REMOVAL
....................8P-4SETTING TRANSMITTER CODES -
STANDARD PROCEDURE...............8M-9
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO GROUND ON FUSES POWERING . . . 8W-01-9
SHAFT - CAUTION, HALF................3-10
SHAFT - DIAGNOSIS AND TESTING,
HALF...............................3-10
SHAFT - DIAGNOSIS AND TESTING,
PROPELLER...........................3-1
SHAFT - FRONT - INSTALLATION,
PROPELLER...........................3-6
SHAFT - FRONT - REMOVAL,
PROPELLER...........................3-6
SHAFT - INSTALLATION, BALANCE........9-74
SHAFT - INSTALLATION, HALF...........3-11
SHAFT - INSTALLATION, IDLER..........9-77
SHAFT - INSTALLATION, INTERMEDIATE . . 19-11
SHAFT - REAR - INSTALLATION,
PROPELLER...........................3-7
SHAFT - REAR - REMOVAL, PROPELLER....3-7
SHAFT - REMOVAL, BALANCE...........9-74
SHAFT - REMOVAL, HALF...............3-10
SHAFT - REMOVAL, IDLER..............9-77
SHAFT - REMOVAL, INTERMEDIATE......19-11
SHAFT ANGLE - STANDARD
PROCEDURES, PROPELLER..............3-3
SHAFT SEAL - INSTALLATION, FRONT
OUTPUT.....................21-208,21-246
SHAFT SEAL - INSTALLATION, REAR
OUTPUT............................21-212
SHAFT SEAL - REMOVAL, FRONT
OUTPUT.....................21-208,21-246
SHAFT SEAL - REMOVAL, REAR OUTPUT . 21-210
SHAFT SEALS - INSTALLATION, AXLE....3-102,
3-38
SHAFT SEALS - REMOVAL, AXLE....3-101,3-37
SHAFT, SPECIFICATIONS - HALF..........3-11
SHAFT, SPECIFICATIONS - PROPELLER.....3-6
SHAFTS - INSTALLATION, AXLE . 3-101,3-37,3-65
SHAFTS - REMOVAL, AXLE.....3-101,3-37,3-65
SHIELD - INSTALLATION, FRONT
WHEELHOUSE SPLASH...............23-143
SHIELD - INSTALLATION, REAR
WHEELHOUSE SPLASH...............23-144
SHIELD - REMOVAL, FRONT
WHEELHOUSE SPLASH...............23-143
SHIELD - REMOVAL, REAR
WHEELHOUSE SPLASH...............23-144
SHIELDS - DESCRIPTION, HEAT..........11-4
SHIELDS - INSTALLATION, SEAT
CUSHION SIDE.....................23-167
SHIELDS - REMOVAL, SEAT CUSHION
SIDE.............................23-167
SHIFT BEZEL - INSTALLATION.........23-158
SHIFT BEZEL - REMOVAL.............23-158
SHIFT BOOT - INSTALLATION, 4WD
FLOOR............................23-156
SHIFT BOOT - REMOVAL, 4WD FLOOR . . . 23-156
SHIFT INTERLOCK SYSTEM -
DESCRIPTION, BRAKE TRANSMISSION . . 21-124
SHIFT INTERLOCK SYSTEM - DIAGNOSIS
AND TESTING, BRAKE TRANSMISSION . . 21-125
SHIFT INTERLOCK SYSTEM -
OPERATION, BRAKE TRANSMISSION....21-125
SHIFT LEVER - INSTALLATION . . . 21-214,21-249
SHIFT LEVER - REMOVAL.......21-213,21-248
SHIFT MECHANISM - DESCRIPTION.....21-160
SHIFT MECHANISM - INSTALLATION....21-160
SHIFT MECHANISM - OPERATION
......21-160
SHIFT MECHANISM - REMOVAL
........21-160
SHOCK - INSTALLATION
................2-18
SHOCK - REMOVAL
....................2-18
SHOES - INSTALLATION, DRUM BRAKE
....5-11
SHOES - REMOVAL, DRUM BRAKE
.......5-11
SHORT TO GROUND - STANDARD
PROCEDURE, TESTING FOR A
........8W-01-9
SHORT TO GROUND ON FUSES
POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A
...........................8W-01-9
SIDE - INSTALLATION, LEFT
.........2-12,2-15
SIDE - INSTALLATION, RIGHT
........2-12,2-15
SIDE - REMOVAL, LEFT
.............2-11,2-15
SIDE - REMOVAL, RIGHT
...........2-11,2-14
SIDE BEZEL - INSTALLATION,
INSTRUMENT PANEL PASSENGER
......23-154SIDE BEZEL - REMOVAL, INSTRUMENT
PANEL PASSENGER..................23-154
SIDE BEZELS - INSTALLATION,
INSTRUMENT PANEL DRIVER..........23-154
SIDE BEZELS - REMOVAL, INSTRUMENT
PANEL DRIVER.....................23-153
SIDE CURTAIN AIRBAG - DESCRIPTION . . . 8O-38
SIDE CURTAIN AIRBAG - INSTALLATION . . 8O-41
SIDE CURTAIN AIRBAG - OPERATION....8O-39
SIDE CURTAIN AIRBAG - REMOVAL......8O-40
SIDE IMPACT AIRBAG CONTROL
MODULE - DESCRIPTION..............8O-43
SIDE IMPACT AIRBAG CONTROL
MODULE - INSTALLATION.............8O-45
SIDE IMPACT AIRBAG CONTROL
MODULE - OPERATION................8O-43
SIDE IMPACT AIRBAG CONTROL
MODULE - REMOVAL.................8O-44
SIDE MOLDINGS - INSTALLATION, BODY . 23-140
SIDE MOLDINGS - REMOVAL, BODY....23-140
SIDE RAIL WEATHERSTRIP/RETAINER -
INSTALLATION......................23-186
SIDE RAIL WEATHERSTRIP/RETAINER -
REMOVAL.........................23-186
SIDE SHIELDS - INSTALLATION, SEAT
CUSHION..........................23-167
SIDE SHIELDS - REMOVAL, SEAT
CUSHION..........................23-167
SIDE VIEW MIRROR - INSTALLATION....23-145
SIDE VIEW MIRROR - REMOVAL.......23-145
SIDEVIEW MIRROR - REMOVAL..........8N-13
SIGNAL INDICATOR - DESCRIPTION,
TURN..............................8J-34
SIGNAL INDICATOR - OPERATION, TURN . . 8J-34
SILL SCUFF PLATE - INSTALLATION,
DOOR............................23-157
SILL SCUFF PLATE - REMOVAL, DOOR . . . 23-157
SINGLE CARDAN UNIVERSAL JOINTS -
ASSEMBLY...........................3-9
SINGLE CARDAN UNIVERSAL JOINTS -
DISASSEMBLY.........................3-8
SIREN - DESCRIPTION................8Q-16
SIREN - INSTALLATION...............8Q-17
SIREN - OPERATION..................8Q-17
SIREN - REMOVAL...................8Q-17
SKID PLATE - INSTALLATION, FRONT......13-6
SKID PLATE - INSTALLATION, FUEL
TANK ...............................13-9
SKID PLATE - INSTALLATION, TRANSFER
CASE...............................13-7
SKID PLATE - REMOVAL, FRONT.........13-6
SKID PLATE - REMOVAL, FUEL TANK......13-9
SKID PLATE - REMOVAL, TRANSFER
CASE...............................13-7
SKIS INDICATOR - DESCRIPTION........8J-31
SKIS INDICATOR - OPERATION..........8J-31
SKIS INITIALIZATION - STANDARD
PROCEDURE.........................8Q-8
SLEEVE - INSTALLATION, HEADREST....23-164
SLEEVE - REMOVAL, HEADREST.......23-164
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-27
SOLENOID - INSTALLATION, EVAP/
PURGE.............................25-27
SOLENOID - OPERATION, EVAP/PURGE . . . 25-27
SOLENOID - REMOVAL, EVAP/PURGE.....25-27
SOLENOID SWITCH VALVE -
DESCRIPTION......................21-161
SOLENOID SWITCH VALVE - OPERATION . 21-161
SOLENOIDS - DESCRIPTION...........21-161
SOLENOIDS - OPERATION.............21-162
SOLENOID/TRS ASSEMBLY -
DESCRIPTION, TRANSMISSION........21-169
SOLENOID/TRS ASSEMBLY -
INSTALLATION, TRANSMISSION........21-170
SOLENOID/TRS ASSEMBLY -
OPERATION, TRANSMISSION..........21-169
SOLENOID/TRS ASSEMBLY - REMOVAL,
TRANSMISSION.....................21-170
SPACER - INSTALLATION, COLLAPSIBLE . . . 3-70
SPACER - REMOVAL, COLLAPSIBLE.......3-70
SPARE TIRE - INSTALLATION............22-9
SPARE TIRE - REMOVAL
................22-8
SPARE TIRE &TEMPORARY -
DESCRIPTION
........................22-6
SPARK PLUG - CLEANING SPARK
PLUGS
.............................8I-15
SPARK PLUG - DESCRIPTION
...........8I-12
SPARK PLUG - INSTALLATION
...........8I-15
24 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1767 of 1803
TRANSCEIVER MODULE - DESCRIPTION,
INTRUSION.........................8Q-14
TRANSCEIVER MODULE -
INSTALLATION, INTRUSION............8Q-16
TRANSCEIVER MODULE - OPERATION,
INTRUSION.........................8Q-15
TRANSCEIVER MODULE - REMOVAL,
INTRUSION.........................8Q-15
TRANSFER CASE - NV231 - ASSEMBLY . . 21-194
TRANSFER CASE - NV231 - CLEANING . . 21-190
TRANSFER CASE - NV231 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV231 -
DESCRIPTION......................21-178
TRANSFER CASE - NV231 - DIAGNOSIS
AND TESTING......................21-180
TRANSFER CASE - NV231 -
DISASSEMBLY......................21-182
TRANSFER CASE - NV231 - INSPECTION . 21-190
TRANSFER CASE - NV231 -
INSTALLATION......................21-205
TRANSFER CASE - NV231 - OPERATION . 21-179
TRANSFER CASE - NV231 - REMOVAL . . . 21-181
TRANSFER CASE - NV242 - ASSEMBLY . . 21-230
TRANSFER CASE - NV242 - CLEANING . . 21-227
TRANSFER CASE - NV242 -
DESCRIPTION.........................0-3
TRANSFER CASE - NV242 -
DESCRIPTION......................21-215
TRANSFER CASE - NV242 - DIAGNOSIS
AND TESTING......................21-216
TRANSFER CASE - NV242 -
DISASSEMBLY......................21-218
TRANSFER CASE - NV242 - INSPECTION . 21-228
TRANSFER CASE - NV242 -
INSTALLATION......................21-243
TRANSFER CASE - NV242 - OPERATION . 21-215
TRANSFER CASE - NV242 - REMOVAL . . . 21-217
TRANSFER CASE, NV231.............21-206
TRANSFER CASE, NV242.............21-244
TRANSFER CASE SKID PLATE -
INSTALLATION........................13-7
TRANSFER CASE SKID PLATE -
REMOVAL...........................13-7
TRANSFER CASE, SPECIFICATIONS -
NV242............................21-244
TRANSMISSION - 45RFE -
DESCRIPTION, AUTOMATIC.............21-76
TRANSMISSION - 45RFE - OPERATION,
AUTOMATIC.........................21-77
TRANSMISSION - DESCRIPTION,
MANUAL.............................0-2
TRANSMISSION - DIAGNOSIS AND
TESTING, AUTOMATIC.................21-77
TRANSMISSION - DIAGNOSIS AND
TESTING, MANUAL...............21-2,21-33
TRANSMISSION CLUTCH OPERATION -
DIAGNOSIS AND TESTING, AIR
CHECKING..........................21-80
TRANSMISSION CONTROL MODULE -
DESCRIPTION.......................8E-18
TRANSMISSION CONTROL MODULE -
OPERATION.........................8E-18
TRANSMISSION CONTROL RELAY -
DESCRIPTION......................21-168
TRANSMISSION CONTROL RELAY -
OPERATION........................21-168
TRANSMISSION FILL - STANDARD
PROCEDURE.......................21-128
TRANSMISSION FLUID - DESCRIPTION,
AUTOMATIC...........................0-2
TRANSMISSION FLUID - OPERATION,
AUTOMATIC...........................0-4
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - INSTALLATION....8L-83
TRANSMISSION RANGE INDICATOR
ILLUMINATION BULB - REMOVAL........8L-82
TRANSMISSION RANGE SENSOR -
DESCRIPTION
......................21-168
TRANSMISSION RANGE SENSOR -
OPERATION
........................21-168
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DESCRIPTION, BRAKE
.......21-124
TRANSMISSION SHIFT INTERLOCK
SYSTEM - DIAGNOSIS AND TESTING,
BRAKE
............................21-125
TRANSMISSION SHIFT INTERLOCK
SYSTEM - OPERATION, BRAKE
.........21-125TRANSMISSION SOLENOID/TRS
ASSEMBLY - DESCRIPTION............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - INSTALLATION...........21-170
TRANSMISSION SOLENOID/TRS
ASSEMBLY - OPERATION.............21-169
TRANSMISSION SOLENOID/TRS
ASSEMBLY - REMOVAL...............21-170
TRANSMISSION, SPECIAL TOOLS - RFE . . 21-120
TRANSMISSION, SPECIFICATIONS......21-119
TRANSMISSION TEMPERATURE SENSOR
- DESCRIPTION.....................21-170
TRANSMISSION TEMPERATURE SENSOR
- OPERATION.......................21-170
TRANSMITTER - DESCRIPTION,
UNIVERSAL.........................8M-8
TRANSMITTER - DIAGNOSIS AND
TESTING, REMOTE KEYLESS ENTRY......8N-8
TRANSMITTER - DIAGNOSIS AND
TESTING, UNIVERSAL.................8M-8
TRANSMITTER - OPERATION,
UNIVERSAL.........................8M-8
TRANSMITTER - SPECIFICATIONS,
REMOTE KEYLESS ENTRY..............8N-9
TRANSMITTER BATTERIES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER CODES - STANDARD
PROCEDURE, ERASING................8M-8
TRANSMITTER CODES - STANDARD
PROCEDURE, SETTING.................8M-9
TRANSMITTER CUSTOMER
PREFERENCES - STANDARD
PROCEDURE, RKE.....................8N-8
TRANSMITTER PROGRAMING -
STANDARD PROCEDURE, RKE...........8N-9
TRANSPONDER KEY - DESCRIPTION.....8Q-18
TRANSPONDER KEY - OPERATION.......8Q-18
TRANSPONDER PROGRAMMING -
STANDARD PROCEDURE, SENTRY KEY....8Q-8
TRAY - DESCRIPTION, BATTERY.........8F-21
TRAY - INSTALLATION, BATTERY........8F-21
TRAY - OPERATION, BATTERY..........8F-21
TRAY - REMOVAL, BATTERY............8F-21
TREAD WEAR INDICATORS - DIAGNOSIS
AND TESTING........................22-8
TRIM - INSTALLATION, B-PILLAR
LOWER...........................23-157
TRIM - INSTALLATION, B-PILLAR UPPER . 23-158
TRIM - REMOVAL, B-PILLAR LOWER....23-157
TRIM - REMOVAL, B-PILLAR UPPER....23-157
TRIM AND GRAB HANDLE -
INSTALLATION, A-PILLAR.............23-156
TRIM AND GRAB HANDLE - REMOVAL,
A-PILLAR..........................23-156
TRIM COVER - INSTALLATION, COWL . . . 23-157
TRIM COVER - REMOVAL, COWL.......23-157
TRIM LACE - INSTALLATION, OPENING . . 23-180
TRIM LACE - REMOVAL, OPENING......23-180
TRIM PANEL - INSTALLATION . . . 23-126,23-132,
23-138
TRIM PANEL - INSTALLATION, QUARTER . 23-159
TRIM PANEL - REMOVAL . 23-125,23-132,23-138
TRIM PANEL - REMOVAL, QUARTER....23-159
TRIP DEFINITION - DESCRIPTION........25-19
TROUBLE CODES - DESCRIPTION,
DIAGNOSTIC.........................25-2
TUBE - DESCRIPTION, A/C ORIFICE......24-50
TUBE - INSTALLATION, A/C ORIFICE......24-50
TUBE - INSTALLATION, DRAIN.........23-181
TUBE - OPERATION, A/C ORIFICE........24-50
TUBE - REMOVAL, A/C ORIFICE.........24-50
TUBE - REMOVAL, DRAIN.............23-180
TURN SIGNAL INDICATOR -
DESCRIPTION.......................8J-34
TURN SIGNAL INDICATOR - OPERATION . . 8J-34
TURNING LOOP ADJUSTER -
INSTALLATION, SEAT BELT.............8O-38
TURNING LOOP ADJUSTER - REMOVAL,
SEAT BELT .........................8O-37
UNIT - ADJUSTMENT, FRONT FOG LAMP . . 8L-25
UNIT - ADJUSTMENT, HEADLAMP
.......8L-42
UNIT - DIAGNOSIS AND TESTING, FUEL
LEVEL SENDING
......................14-9
UNIT - INSTALLATION, ASH RECEIVER
LAMP
..............................8L-72
UNIT - INSTALLATION, CARGO LAMP
.....8L-74
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP
................8L-19UNIT - INSTALLATION, COURTESY LAMP . . 8L-77
UNIT - INSTALLATION, FRONT FOG
LAMP..............................8L-25
UNIT - INSTALLATION, FRONT LAMP.....8L-28
UNIT - INSTALLATION, HEADLAMP.......8L-42
UNIT - INSTALLATION, LICENSE PLATE
LAMP..............................8L-46
UNIT - INSTALLATION, READING LAMP . . . 8L-81
UNIT - INSTALLATION, REAR LAMP......8L-60
UNIT - INSTALLATION, REPEATER LAMP . . 8L-61
UNIT - REMOVAL, ASH RECEIVER LAMP . . 8L-72
UNIT - REMOVAL, CARGO LAMP........8L-74
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP................8L-19
UNIT - REMOVAL, COURTESY LAMP.....8L-76
UNIT - REMOVAL, FRONT FOG LAMP.....8L-25
UNIT - REMOVAL, FRONT LAMP.........8L-27
UNIT - REMOVAL, HEADLAMP..........8L-41
UNIT - REMOVAL, LICENSE PLATE LAMP . . 8L-45
UNIT - REMOVAL, READING LAMP.......8L-81
UNIT - REMOVAL, REAR LAMP..........8L-59
UNIT - REMOVAL, REPEATER LAMP......8L-60
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING.....................14-10
UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING......................14-9
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING......................14-9
UNIVERSAL JOINTS - ASSEMBLY,
SINGLE CARDAN.......................3-9
UNIVERSAL JOINTS - DISASSEMBLY,
SINGLE CARDAN.......................3-8
UNIVERSAL TRANSMITTER -
DESCRIPTION........................8M-8
UNIVERSAL TRANSMITTER - DIAGNOSIS
AND TESTING........................8M-8
UNIVERSAL TRANSMITTER - OPERATION . . 8M-8
UNLOCK SWITCH - INSTALLATION,
DOOR LOCK.........................8N-5
UNLOCK SWITCH - REMOVAL, DOOR
LOCK...............................8N-4
UPPER BALL JOINT - INSTALLATION......2-20
UPPER BALL JOINT - REMOVAL..........2-20
UPPER CONTROL ARM - INSTALLATION . . . 2-21
UPPER CONTROL ARM - REMOVAL.......2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - DESCRIPTION.........2-20
UPPER SUSPENSION ARM, BUSHINGS,
AND BALL JOINT - OPERATION..........2-20
UPPER TRIM - INSTALLATION, B-PILLAR . 23-158
UPPER TRIM - REMOVAL, B-PILLAR....23-157
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO.............8W-01-1
USING MIDTRONICS ELECTRICAL
TESTER - STANDARD PROCEDURE.......8F-15
V-6 - ENGINE FIRING ORDER, 3.7L........8I-2
V-6 - IGNITION COIL RESISTANCE, 3.7L....8I-3
VACUUM CHECK VALVE - DESCRIPTION . . 24-28
VACUUM CHECK VALVE - INSTALLATION . . 24-28
VACUUM CHECK VALVE - OPERATION....24-28
VACUUM CHECK VALVE - REMOVAL......24-28
VACUUM LINES - DESCRIPTION.........25-33
VACUUM RESERVOIR - DESCRIPTION.....8P-7
VACUUM RESERVOIR - DIAGNOSIS AND
TESTING............................8P-7
VACUUM RESERVOIR - INSTALLATION....8P-8
VACUUM RESERVOIR - OPERATION.......8P-7
VACUUM RESERVOIR - REMOVAL........8P-7
VACUUM SYSTEM - DIAGNOSIS AND
TESTING............................24-6
VALUE - DESCRIPTION, LOAD..........25-20
VALVE - DESCRIPTION, FLOW
MANAGEMENT.......................14-6
VALVE - DESCRIPTION, FRONT CHECK....8R-8
VALVE - DESCRIPTION, FUEL TANK
CHECK.............................14-28
VALVE - DESCRIPTION, HIGH PRESSURE
RELIEF.............................24-42
VALVE - DESCRIPTION, PCV............25-29
VALVE - DESCRIPTION, REAR CHECK
....8R-34
VALVE - DESCRIPTION, SOLENOID
SWITCH
...........................21-161
VALVE - DESCRIPTION, VACUUM CHECK
. . 24-28
VALVE - DIAGNOSIS AND TESTING, PCV
. . 25-31
VALVE - DIAGNOSIS AND TESTING,
PROPORTIONING
.....................5-20
28 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page