radio JEEP LIBERTY 2002 KJ / 1.G Repair Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2002, Model line: LIBERTY, Model: JEEP LIBERTY 2002 KJ / 1.GPages: 1803, PDF Size: 62.3 MB
Page 1615 of 1803
(14) Remove the two roll down bracket bolts at the
left cowl side panel. (Fig. 6)
(15) Remove the ground strap bolt and disconnect
the restraint module electrical connector. (Fig. 3)
(16) Remove the glove box. (Refer to 23 - BODY/
INSTRUMENT PANEL/GLOVE BOX - REMOVAL)
(17) Remove the two HVAC mounting bolts behind
the center trim. (Fig. 3)
(18) Remove the passenger side trim bezel. (Refer
to 23 - BODY/INSTRUMENT PANEL/IP PASSEN-
GER SIDE BEZEL - REMOVAL)(19) Remove the HVAC mounting bolt above the
glove box striker. (Fig. 4)
(20) Remove the HVAC bolt at the lower outside
corner of the glove box opening. (Fig. 5)
(21) Remove the passenger side cowl trim cover.
(Refer to 23 - BODY/INTERIOR/COWL TRIM
COVER - REMOVAL)
(22) Disconnect the blower resistor electrical con-
nector. (Fig. 5)
(23) Remove the two roll down bracket bolts at the
right cowl side panel.
Fig. 2 PEDAL SUPPORT BRACKET
1 - PEDAL SUPPORT BRACKET
2 - BOLTS
3 - BOLTS
4 - ELECTRICAL CONNECTOR
Fig. 3 HVAC BOLTS
1 - RESTRAINT MODULE
2 - HVAC BOLTS
3 - RADIO WIRE HARNESS
Fig. 4 HVAC UPPER BOLT
1 - BOLT
2 - GLOVE BOX STRIKER
3 - HVAC UNIT
Fig. 5 HVAC CONNECTIONS
1 - GLOVE BOX STRIKER
2 - BLOWER RESISTOR
3 - VACUUM CHECK VALVE
4 - BOLT
23 - 150 INSTRUMENT PANELKJ
INSTRUMENT PANEL ASSEMBLY (Continued)
Page 1616 of 1803
(24) Disconnect the vacuum check valve and the
vacuum reservoir. (Fig. 5)
(25) Disconnect the blower motor electrical connec-
tor.
(26) Remove the four bolts at the top of the instru-
ment panel connecting to the cowl front panel.
(27) Roll the instrument panel rearward and
remove the wire harness from routing channel in the
rear.
(28) Disconnect the push pin fastener and position
aside the radio wire harness. Note the location of the
harness for installation.
(29) Remove the instrument panel.
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THISIS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIR-
BAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
(1) Position the instrument panel into the vehicle.
(2) Position the wire harness into the rear routing
channel and roll the instrument panel back against
the cowl.
(3) Position the radio wire harness and seat the
push pin fastener.
NOTE: Position the speaker wires through the
speaker openings.
(4) Install the four bolts at the top of the instru-
ment panel connecting to the cowl front panel and
tighten to 28 N´m (21 ft. lbs.).
(5) Connect the blower motor electrical connector.
(6) Connect the vacuum check valve and the vac-
uum reservoir.
(7) Connect the blower resister electrical connector.
NOTE: Do not push or pull bracket. Tighten at the
rest position.
Fig. 6 INSTRUMENT PANEL ASSEMBLY
1 - TOP BOLTS (4)
2 - CENTER SUPPORT BRACKET
3 - NUTS (4)4 - ROLL DOWN BOLTS (4)
5 - INSTRUMENT PANEL ASSEMBLY
KJINSTRUMENT PANEL 23 - 151
INSTRUMENT PANEL ASSEMBLY (Continued)
Page 1617 of 1803
(8) Install the two roll down bracket bolts at the
right cowl side panel and tighten to 54 N´m (40 ft.
lbs.).
(9) Install the HVAC mounting bolt at the lower
outside corner of the glove box opening and tighten
to 6 N´m (55 in. lbs.).
(10) Install the HVAC mounting bolt above the
glove box striker.
(11) Install the passenger side trim bezel. (Refer to
23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL PASSENGER SIDE BEZEL - INSTALLA-
TION)
(12) Install the passenger side cowl trim cover.
(Refer to 23 - BODY/INTERIOR/COWL TRIM
COVER - INSTALLATION)
(13) Install the glove box. (Refer to 23 - BODY/IN-
STRUMENT PANEL/GLOVE BOX - INSTALLA-
TION)
NOTE: Do not push or pull bracket. Tighten at the
rest position.
(14) Install the two roll down bracket bolts at the
drivers cowl side panel and tighten to 54 N´m (40 ft.
lbs.).
(15) Install the two bolts at the bottom side of the
pedal support bracket.
(16) Install the two bolts at the front of the pedal
support bracket.
(17) Connect the electrical connector at the inner
side of the pedal support bracket.
(18) Connect the wiring harness electrical connec-
tors at the junction block.
(19) Connect the wire harness electrical connector
behind the drivers side cowl trim cover.
(20) Install the left cowl trim cover. (Refer to 23 -
BODY/INTERIOR/COWL TRIM COVER - INSTAL-
LATION)
(21) Install the steering column. (Refer to 19 -
STEERING/COLUMN - INSTALLATION)
(22) Install the two HVAC mounting bolts behind
the center trim.
(23) Install the ground strap and bolt and connect
the restraint module electrical connector.
(24) Install the center support bracket and hold it
tight against the instrument panel.
(25) Tighten the lower nuts to 23 N´m (17 ft. lbs.).
(26) Tighten the upper bracket nuts to 23 N´m (17
ft. lbs.).
(27) Install the radio. (Refer to 8 - ELECTRICAL/
AUDIO/RADIO - INSTALLATION)
(28) Install the floor console. (Refer to 23 - BODY/
INTERIOR/FLOOR CONSOLE - INSTALLATION)
(29) Install the speakers.
(30) Install the instrument panel top cover. (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL TOP COVER - INSTALLATION)(31) Reconnect the battery ground cable.
INSTRUMENT PANEL TOP
COVER
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Remove the a-pillar trim. (Refer to 23 - BODY/
INTERIOR/A-PILLAR TRIM AND GRAB HANDLE -
REMOVAL)
(2) Using a trim stick C-4755 or equivalent,
release the attachment clips and remove the top
cover. (Fig. 7)
Fig. 7 INSTRUMENT PANEL COVERS
1 - SIDE COVER
2 - INSTRUMENT PANEL ASSEMBLY
3 - TOP COVER
23 - 152 INSTRUMENT PANELKJ
INSTRUMENT PANEL ASSEMBLY (Continued)
Page 1750 of 1803
FUEL PRESSURE REGULATOR -
DESCRIPTION.......................14-13
FUEL PRESSURE REGULATOR -
INSTALLATION.......................14-14
FUEL PRESSURE REGULATOR -
OPERATION.........................14-14
FUEL PRESSURE REGULATOR -
REMOVAL..........................14-14
FUEL PUMP - DESCRIPTION............14-15
FUEL PUMP - OPERATION.............14-15
FUEL PUMP AMPERAGE TEST -
DIAGNOSIS AND TESTING.............14-16
FUEL PUMP CAPACITY TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP MODULE - DESCRIPTION....14-18
FUEL PUMP MODULE - INSTALLATION . . . 14-19
FUEL PUMP MODULE - OPERATION......14-18
FUEL PUMP MODULE - REMOVAL.......14-18
FUEL PUMP PRESSURE TEST -
DIAGNOSIS AND TESTING.............14-15
FUEL PUMP RELAY - DESCRIPTION......14-34
FUEL PUMP RELAY - DIAGNOSIS AND
TESTING...........................14-34
FUEL PUMP RELAY - INSTALLATION.....14-34
FUEL PUMP RELAY - OPERATION........14-34
FUEL PUMP RELAY - REMOVAL.........14-34
FUEL PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD........................8I-4
FUEL RAIL - DESCRIPTION.............14-21
FUEL RAIL - INSTALLATION..............14-24
FUEL RAIL - OPERATION...............14-21
FUEL RAIL - REMOVAL................14-22
FUEL SYSTEM PRESSURE RELEASE -
STANDARD PROCEDURE................14-4
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-5
FUEL SYSTEM, SPECIAL TOOLS..........14-6
FUEL TANK - DESCRIPTION............14-24
FUEL TANK - INSTALLATION............14-27
FUEL TANK - OPERATION..............14-24
FUEL TANK - REMOVAL...............14-25
FUEL TANK CHECK VALVE -
DESCRIPTION.......................14-28
FUEL TANK CHECK VALVE -
INSTALLATION.......................14-28
FUEL TANK CHECK VALVE - OPERATION . . 14-28
FUEL TANK CHECK VALVE - REMOVAL....14-28
FUEL TANK SKID PLATE - INSTALLATION . . . 13-9
FUEL TANK SKID PLATE - REMOVAL......13-9
FULL TIME INDICATOR - DESCRIPTION . . . 8J-29
FULL TIME INDICATOR - OPERATION.....8J-30
FUNCTION - DIAGNOSIS AND TESTING,
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER..................8G-9
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-3
FUSE - INSTALLATION, IOD..........8W-97-3
FUSE - OPERATION, IOD.............8W-97-3
FUSE - REMOVAL, IOD..............8W-97-3
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON.......8W-01-9
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL.....9-10
GAP AND FLUSH - SPECIFICATIONS.....23-116
GAS ENGINES - GENERATOR RATINGS....8F-23
GAS POWERED - STARTER MOTOR......8F-39
GAS POWERED - TORQUE
.............8F-38
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD
..................9-19,9-30
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE
.........9-9
GATE - INSTALLATION, SWING
.........23-138
GATE - REMOVAL, SWING
............23-138
GATE AJAR INDICATOR - DESCRIPTION
. . . 8J-20
GATE AJAR INDICATOR - OPERATION
.....8J-20
GATE BELTLINE WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE BELTLINE WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GATE OPENING WEATHERSTRIP -
INSTALLATION, SWING
...............23-186
GATE OPENING WEATHERSTRIP -
REMOVAL, SWING
...................23-186
GAUGE - DESCRIPTION, ENGINE
TEMPERATURE
......................8J-18
GAUGE - DESCRIPTION, FUEL
...........8J-19GAUGE - OPERATION, ENGINE
TEMPERATURE......................8J-18
GAUGE - OPERATION, FUEL............8J-20
GEAR - DESCRIPTION.................19-13
GEAR - INSTALLATION, PINION
GEAR/RING..........................3-46
GEAR - OPERATION...................19-13
GEAR - REMOVAL, PINION GEAR/RING....3-44
GEAR/RING GEAR - INSTALLATION,
PINION.............................3-46
GEAR/RING GEAR - REMOVAL, PINION....3-44
GEAR/RING GEAR/TONE RING -
INSTALLATION, PINION............3-112,3-82
GEAR/RING GEAR/TONE RING -
REMOVAL, PINION...............3-110,3-79
GEARSHIFT CABLE - ADJUSTMENTS....21-130
GEARSHIFT CABLE - DIAGNOSIS AND
TESTING..........................21-128
GEARSHIFT CABLE - INSTALLATION.....21-129
GEARSHIFT CABLE - REMOVAL........21-128
GEAR/TONE RING - INSTALLATION,
PINION GEAR/RING...............3-112,3-82
GEAR/TONE RING - REMOVAL, PINION
GEAR/RING.....................3-110,3-79
GEARTRAIN - ASSEMBLY, PLANETARY . . . 21-160
GEARTRAIN - CLEANING, PLANETARY . . . 21-159
GEARTRAIN - DESCRIPTION,
PLANETARY........................21-157
GEARTRAIN - DISASSEMBLY,
PLANETARY........................21-159
GEARTRAIN - INSPECTION, PLANETARY . 21-159
GEARTRAIN - OPERATION, PLANETARY . . 21-157
GENERAL - WARNINGS.............8W-01-7
GENERATOR - DESCRIPTION...........8F-25
GENERATOR - INSTALLATION...........8F-26
GENERATOR - OPERATION.............8F-25
GENERATOR - REMOVAL...............8F-25
GENERATOR DECOUPLER - DIAGNOSIS
AND TESTING.......................8F-27
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-26
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-30
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-27
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-27
GENERATOR RATINGS, GAS ENGINES....8F-23
GLASS - INSTALLATION, DOOR . . 23-122,23-129,
23-172
GLASS - INSTALLATION, FLIP-UP.......23-136
GLASS - REMOVAL, DOOR......23-122,23-129,
23-172
GLASS - REMOVAL, FLIP-UP..........23-136
GLASS AJAR INDICATOR - DESCRIPTION . . 8J-21
GLASS AJAR INDICATOR - OPERATION . . . 8J-21
GLASS AJAR SWITCH - DESCRIPTION,
FLIP-UP............................8L-77
GLASS AJAR SWITCH - OPERATION,
FLIP-UP............................8L-77
GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE, REAR..........8G-4
GLASS LATCH - INSTALLATION, FLIP-UP . 23-136
GLASS LATCH - REMOVAL, FLIP-UP.....23-136
GLASS PANEL - INSTALLATION........23-178
GLASS PANEL - REMOVAL............23-178
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-178
GLASS PANEL SEAL - INSTALLATION
....23-178
GLASS PANEL SEAL - REMOVAL
.......23-178
GLASS RELEASE SWITCH - DIAGNOSIS
AND TESTING, FLIP-UP
................8N-5
GLASS RUN CHANNEL - INSTALLATION
. 23-123,
23-130
GLASS RUN CHANNEL - REMOVAL
.....23-123,
23-130
GLASS SUPPORT CYLINDER -
INSTALLATION, FLIP-UP
..............23-139
GLASS SUPPORT CYLINDER -
REMOVAL, FLIP-UP
..................23-139
GLOVE BOX - INSTALLATION
..........23-148
GLOVE BOX - REMOVAL
..............23-148
GLOVE BOX LATCH - INSTALLATION
....23-148
GLOVE BOX LATCH - REMOVAL
........23-148
GLOVE BOX LATCH STRIKER -
INSTALLATION
......................23-149
GLOVE BOX LATCH STRIKER - REMOVAL
. 23-148GRAB HANDLE - INSTALLATION,
A-PILLAR TRIM.....................23-156
GRAB HANDLE - REMOVAL, A-PILLAR
TRIM.............................23-156
GRID - DESCRIPTION, REAR WINDOW
DEFOGGER..........................8G-5
GRID - DIAGNOSIS AND TESTING, REAR
WINDOW DEFOGGER..................8G-5
GRID - OPERATION, REAR WINDOW
DEFOGGER..........................8G-5
GRID REPAIR - STANDARD PROCEDURE,
REAR GLASS HEATING.................8G-4
GRILLE - INSTALLATION..............23-142
GRILLE - INSTALLATION, COWL........23-140
GRILLE - REMOVAL..................23-142
GRILLE - REMOVAL, COWL...........23-140
GRILLE OPENING REINFORCEMENT -
INSTALLATION......................23-142
GRILLE OPENING REINFORCEMENT -
REMOVAL.........................23-142
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO..............................8W-01-9
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-9
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-11
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION.................8A-10
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION.................8A-10
GROUNDS - DESCRIPTION, POWER......8E-13
GUARD - DESCRIPTION, THERMAL......8F-20
GUARD - INSTALLATION, THERMAL......8F-20
GUARD - OPERATION, THERMAL........8F-20
GUARD - REMOVAL, THERMAL..........8F-20
GUIDE ASSEMBLY - INSTALLATION.....23-179
GUIDE ASSEMBLY - REMOVAL.........23-179
GUIDE SEALS - DESCRIPTION, VALVE . 9-29,9-38
GUIDES - DESCRIPTION, VALVE......9-19,9-30
HALF SHAFT - CAUTION................3-10
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-10
HALF SHAFT - INSTALLATION............3-11
HALF SHAFT - REMOVAL...............3-10
HALF SHAFT, SPECIFICATIONS...........3-11
HANDLE - INSTALLATION, A-PILLAR
TRIM AND GRAB....................23-156
HANDLE - INSTALLATION, ASSIST......23-157
HANDLE - INSTALLATION, EXTERIOR . . . 23-123,
23-130,23-136
HANDLE - INSTALLATION, LATCH
RELEASE..........................23-120
HANDLE - REMOVAL, A-PILLAR TRIM
AND GRAB.........................23-156
HANDLE - REMOVAL, ASSIST..........23-157
HANDLE - REMOVAL, EXTERIOR . 23-123,23-130,
23-136
HANDLE - REMOVAL, LATCH RELEASE . . 23-120
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING
..........................8W-01-7
HAZARD SWITCH - DESCRIPTION
.......8L-29
HAZARD SWITCH - INSTALLATION
.......8L-30
HAZARD SWITCH - OPERATION
.........8L-29
HAZARD SWITCH - REMOVAL
..........8L-30
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION
........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION
........................5-36
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION
..........................5-35
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL
...........................5-36
HEAD - DESCRIPTION, CYLINDER
........9-30
HEAD COVER(S) - DESCRIPTION,
CYLINDER
...........................9-25
HEAD COVER(S) - INSTALLATION,
CYLINDER
.......................9-26,9-34
HEAD COVER(S) - REMOVAL, CYLINDER
. . 9-25,
9-34
KJINDEX 11
Description Group-Page Description Group-Page Description Group-Page
Page 1756 of 1803
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-35
MOTOR - OPERATION, REAR WIPER.....8R-41
MOTOR - REMOVAL, BLOWER..........24-30
MOTOR - REMOVAL, DRIVE...........23-182
MOTOR - REMOVAL, HEADLAMP
LEVELING..........................8L-36
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-36
MOTOR - REMOVAL, REAR WIPER......8R-42
MOTOR - REMOVAL, STARTER..........8F-39
MOTOR - REMOVAL, WINDOW..........8N-22
MOTOR, GAS POWERED - STARTER......8F-39
MOTOR RELAY - DESCRIPTION,
BLOWER...........................24-20
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-41
MOTOR RELAY - DIAGNOSIS AND
TESTING, BLOWER...................24-21
MOTOR RELAY - INSTALLATION,
BLOWER...........................24-22
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-43
MOTOR RELAY - OPERATION, BLOWER . . . 24-20
MOTOR RELAY - OPERATION, STARTER . . . 8F-42
MOTOR RELAY - REMOVAL, BLOWER....24-21
MOTOR RELAY - REMOVAL, STARTER....8F-43
MOTOR RESISTOR - DESCRIPTION,
BLOWER...........................24-22
MOTOR RESISTOR - DIAGNOSIS AND
TESTING, BLOWER.....................24-22
MOTOR RESISTOR - INSTALLATION,
BLOWER...........................24-22
MOTOR RESISTOR - OPERATION,
BLOWER...........................24-22
MOTOR RESISTOR - REMOVAL,
BLOWER...........................24-22
MOTOR SWITCH - DESCRIPTION,
BLOWER...........................24-23
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER...................24-23
MOTOR SWITCH - INSTALLATION,
BLOWER...........................24-23
MOTOR SWITCH - OPERATION, BLOWER . . 24-23
MOTOR SWITCH - REMOVAL, BLOWER . . . 24-23
MOUNT - INSTALLATION, FRONT.........9-57
MOUNT - INSTALLATION, REAR..........9-57
MOUNT - REMOVAL, FRONT.............9-56
MOUNT - REMOVAL, REAR..............9-57
MOUNTED STOP LAMP BULB -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP BULB -
REMOVAL, CENTER HIGH..............8L-18
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-19
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-19
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-3
MOUNTING - STANDARD PROCEDURE,
WHEEL............................22-10
MOUNTING BRACKET - INSTALLATION,
PASSENGER AIRBAG.................8O-31
MOUNTING BRACKET - REMOVAL,
PASSENGER AIRBAG.................8O-31
MUFFLER - DESCRIPTION...............11-4
MUFFLER - INSTALLATION
..............11-5
MUFFLER - REMOVAL
..................11-5
MULTI-FUNCTION SWITCH -
DESCRIPTION
.......................8L-46
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING
.......................8L-50
MULTI-FUNCTION SWITCH -
INSTALLATION
.......................8L-53
MULTI-FUNCTION SWITCH - OPERATION
. . 8L-48
MULTI-FUNCTION SWITCH - REMOVAL
. . . 8L-53
NAME PLATES - INSTALLATION,
EXTERIOR
.........................23-141
NAME PLATES - REMOVAL, EXTERIOR
. . . 23-140
NOISE - DIAGNOSIS AND TESTING, A/C
COMPRESSOR
.......................24-42
NOISE - DIAGNOSIS AND TESTING,
WIND
...............................23-3
NOISE DIAGNOSIS, DIAGNOSIS AND
TESTING - WATER DRAINAGE AND
WIND
.............................23-176
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE
.......................22-8NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-9
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-11
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO..................8A-10
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO....................8A-10
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
DESCRIPTION.......................25-20
NOZZLE - DESCRIPTION, FRONT
WASHER...........................8R-11
NOZZLE - DESCRIPTION, REAR WASHER . 8R-36
NOZZLE - INSTALLATION, FRONT
WASHER...........................8R-11
NOZZLE - INSTALLATION, REAR
WASHER...........................8R-37
NOZZLE - OPERATION, FRONT WASHER . . 8R-11
NOZZLE - OPERATION, REAR WASHER . . . 8R-36
NOZZLE - REMOVAL, FRONT WASHER....8R-11
NOZZLE - REMOVAL, REAR WASHER....8R-36
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-8
NV1500 - ASSEMBLY, MANUAL.........21-13
NV1500 - CLEANING, MANUAL..........21-10
NV1500 - DESCRIPTION, MANUAL........21-1
NV1500 - DISASSEMBLY, MANUAL........21-4
NV1500 - INSPECTION, MANUAL..........21-11
NV1500 - INSTALLATION, EXTENSION
HOUSING SEAL......................21-32
NV1500 - INSTALLATION, MANUAL......21-29
NV1500 - MANUAL...................21-30
NV1500 - OPERATION, MANUAL..........21-1
NV1500 - REMOVAL, EXTENSION
HOUSING SEAL......................21-32
NV1500 - REMOVAL, MANUAL...........21-3
NV1500 - SPECIFICATIONS.............21-30
NV231 - ASSEMBLY, TRANSFER CASE . . . 21-194
NV231 - CLEANING, TRANSFER CASE . . . 21-190
NV231 - DESCRIPTION, TRANSFER CASE . . . 0-3
NV231 - DESCRIPTION, TRANSFER CASE . 21-178
NV231 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-180
NV231 - DISASSEMBLY, TRANSFER
CASE.............................21-182
NV231 - INSPECTION, TRANSFER CASE . . 21-190
NV231 - INSTALLATION, TRANSFER
CASE.............................21-205
NV231 - OPERATION, TRANSFER CASE . . 21-179
NV231 - REMOVAL, TRANSFER CASE....21-181
NV231 - TRANSFER CASE.............21-206
NV242 - ASSEMBLY, TRANSFER CASE . . . 21-230
NV242 - CLEANING, TRANSFER CASE . . . 21-227
NV242 - DESCRIPTION, TRANSFER CASE . . . 0-3
NV242 - DESCRIPTION, TRANSFER CASE . 21-215
NV242 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-216
NV242 - DISASSEMBLY, TRANSFER
CASE.............................21-218
NV242 - INSPECTION, TRANSFER CASE . . 21-228
NV242 - INSTALLATION, TRANSFER
CASE.............................21-243
NV242 - OPERATION, TRANSFER CASE . . 21-215
NV242 - REMOVAL, TRANSFER CASE....21-217
NV242 - TRANSFER CASE.............21-244
NV242 TRANSFER CASE,
SPECIFICATIONS....................21-244
NV3550 - ASSEMBLY, MANUAL.........21-48
NV3550 - CLEANING, MANUAL..........21-46
NV3550 - DESCRIPTION, MANUAL.......21-33
NV3550 - DISASSEMBLY, MANUAL.......21-35
NV3550 - INSPECTION, MANUAL........21-46
NV3550 - INSTALLATION, EXTENSION
HOUSING BUSHING...................21-74
NV3550 - INSTALLATION, EXTENSION
HOUSING SEAL......................21-74
NV3550 - INSTALLATION, MANUAL......21-70
NV3550 - MANUAL...................21-71
NV3550 - OPERATION, MANUAL
.........21-33
NV3550 - REMOVAL, EXTENSION
HOUSING BUSHING
...................21-73
NV3550 - REMOVAL, EXTENSION
HOUSING SEAL
......................21-74
NV3550 - REMOVAL, MANUAL
..........21-34
ODOMETER - DESCRIPTION
............8J-25ODOMETER - OPERATION..............8J-25
OFF INDICATOR - DESCRIPTION,
OVERDRIVE.........................8J-26
OFF INDICATOR - OPERATION,
OVERDRIVE.........................8J-26
OIL - DESCRIPTION, REFRIGERANT......24-53
OIL - OPERATION, REFRIGERANT........24-54
OIL - STANDARD PROCEDURE, ENGINE....9-61
OIL FILTER - INSTALLATION.............9-63
OIL FILTER - REMOVAL.................9-63
OIL GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE.............9-10
OIL LEAK - DIAGNOSIS AND TESTING,
ENGINE.............................9-60
OIL LEVEL - STANDARD PROCEDURE,
REFRIGERANT.......................24-54
OIL PAN - CLEANING..................9-63
OIL PAN - DESCRIPTION................9-63
OIL PAN - INSPECTION.................9-63
OIL PAN - INSTALLATION...............9-64
OIL PAN - REMOVAL...................9-63
OIL PRESSURE - DIAGNOSIS AND
TESTING, ENGINE.....................9-60
OIL PRESSURE INDICATOR -
DESCRIPTION, LOW..................8J-23
OIL PRESSURE INDICATOR -
OPERATION, LOW....................8J-23
OIL PRESSURE SENSOR/SWITCH -
DESCRIPTION........................9-65
OIL PRESSURE SENSOR/SWITCH -
INSTALLATION........................9-65
OIL PRESSURE SENSOR/SWITCH -
OPERATION..........................9-65
OIL PRESSURE SENSOR/SWITCH -
REMOVAL...........................9-65
OIL PUMP - ASSEMBLY................9-67
OIL PUMP - ASSEMBLY..............21-151
OIL PUMP - CLEANING...............21-150
OIL PUMP - DESCRIPTION............21-147
OIL PUMP - DISASSEMBLY.............9-65
OIL PUMP - DISASSEMBLY............21-149
OIL PUMP - INSPECTION...............9-66
OIL PUMP - INSPECTION.............21-150
OIL PUMP - INSTALLATION.............9-67
OIL PUMP - OPERATION..............21-147
OIL PUMP - REMOVAL.................9-65
OIL PUMP FRONT SEAL - INSTALLATION . 21-152
OIL PUMP FRONT SEAL - REMOVAL....21-152
OIL PUMP VOLUME CHECK - STANDARD
PROCEDURE.......................21-148
OIL SEAL - FRONT - INSTALLATION,
CRANKSHAFT........................9-47
OIL SEAL - FRONT - REMOVAL,
CRANKSHAFT........................9-46
OIL SEAL - REAR - INSTALLATION,
CRANKSHAFT........................9-48
OIL SEAL - REAR - REMOVAL,
CRANKSHAFT........................9-48
ON-BOARD DIAGNOSTICS (OBD) -
DIAGNOSIS AND TESTING...............7-3
ON/OFF RELAY - DESCRIPTION, WIPER . . . 8R-25
ON/OFF RELAY - DIAGNOSIS AND
TESTING, WIPER.....................8R-26
ON/OFF RELAY - INSTALLATION, WIPER . . 8R-26
ON/OFF RELAY - OPERATION, WIPER....8R-25
ON/OFF RELAY - REMOVAL, WIPER......8R-26
OPEN-CIRCUIT VOLTAGE TEST -
STANDARD PROCEDURE...............8F-12
OPENING DIMENSIONS -
SPECIFICATIONS....................23-111
OPENING FLARE MOLDINGS -
INSTALLATION, FRONT WHEEL.........23-145
OPENING FLARE MOLDINGS -
INSTALLATION, REAR WHEEL..........23-145
OPENING FLARE MOLDINGS -
REMOVAL, FRONT WHEEL............23-145
OPENING FLARE MOLDINGS -
REMOVAL, REAR WHEEL.............23-145
OPENING REINFORCEMENT -
INSTALLATION, GRILLE...............23-142
OPENING REINFORCEMENT - REMOVAL,
GRILLE
...........................23-142
OPENING TRIM LACE - INSTALLATION
. . . 23-180
OPENING TRIM LACE - REMOVAL
......23-180
OPENING WEATHERSTRIP -
INSTALLATION, SWING GATE
..........23-186
OPENING WEATHERSTRIP - REMOVAL,
SWING GATE
.......................23-186
KJINDEX 17
Description Group-Page Description Group-Page Description Group-Page
Page 1759 of 1803
PRIMARY WEATHERSTRIP - REMOVAL,
DOOR............................23-185
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER........8N-9
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM................8E-1
PROGRAMMING - STANDARD
PROCEDURE, SENTRY KEY
TRANSPONDER.......................8Q-8
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - FRONT -
INSTALLATION.........................3-6
PROPELLER SHAFT - FRONT - REMOVAL . . . 3-6
PROPELLER SHAFT - REAR -
INSTALLATION.........................3-7
PROPELLER SHAFT - REAR - REMOVAL....3-7
PROPELLER SHAFT ANGLE - STANDARD
PROCEDURES.........................3-3
PROPELLER SHAFT, SPECIFICATIONS.......3-6
PROPORTIONING VALVE - DIAGNOSIS
AND TESTING........................5-20
PULLEY - DESCRIPTION, GENERATOR
DECOUPLER........................8F-26
PULLEY - INSTALLATION..............19-23
PULLEY - INSTALLATION, GENERATOR
DECOUPLER........................8F-30
PULLEY - OPERATION, GENERATOR
DECOUPLER........................8F-27
PULLEY - REMOVAL..................19-23
PULLEY - REMOVAL, GENERATOR
DECOUPLER........................8F-27
PUMP - ASSEMBLY, OIL................9-67
PUMP - ASSEMBLY, OIL..............21-151
PUMP - CLEANING, OIL..............21-150
PUMP - DESCRIPTION................19-17
PUMP - DESCRIPTION, FUEL...........14-15
PUMP - DESCRIPTION, LEAK DETECTION . 25-27
PUMP - DESCRIPTION, OIL............21-147
PUMP - DESCRIPTION, WATER..........7-29
PUMP - DISASSEMBLY, OIL.............9-65
PUMP - DISASSEMBLY, OIL...........21-149
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-18
PUMP - INSPECTION, OIL...............9-66
PUMP - INSPECTION, OIL.............21-150
PUMP - INSTALLATION, LEAK
DETECTION.........................25-28
PUMP - INSTALLATION, OIL.............9-67
PUMP - OPERATION..................19-17
PUMP - OPERATION, FUEL.............14-15
PUMP - OPERATION, LEAK DETECTION . . . 25-28
PUMP - OPERATION, OIL.............21-147
PUMP - OPERATION, WATER............7-30
PUMP - REMOVAL, LEAK DETECTION....25-28
PUMP - REMOVAL, OIL.................9-65
PUMP AMPERAGE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-16
PUMP CAPACITY TEST - DIAGNOSIS
AND TESTING, FUEL..................14-15
PUMP FRONT SEAL - INSTALLATION,
OIL...............................21-152
PUMP FRONT SEAL - REMOVAL, OIL....21-152
PUMP MODULE - DESCRIPTION, FUEL....14-18
PUMP MODULE - INSTALLATION, FUEL . . . 14-19
PUMP MODULE - OPERATION, FUEL.....14-18
PUMP MODULE - REMOVAL, FUEL.......14-18
PUMP PRESSURE TEST - DIAGNOSIS
AND TESTING, FUEL..................14-15
PUMP RELAY - DESCRIPTION, FUEL.....14-34
PUMP RELAY - DIAGNOSIS AND
TESTING, FUEL......................14-34
PUMP RELAY - INSTALLATION, FUEL.....14-34
PUMP RELAY - OPERATION, FUEL.......14-34
PUMP RELAY - REMOVAL, FUEL........14-34
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL...............8I-4
PUMP, SPECIAL TOOLS - POWER
STEERING..........................19-20
PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-148
PUMP/MOTOR - DESCRIPTION, WASHER
. 8R-18
PUMP/MOTOR - INSTALLATION,
WASHER
...........................8R-20
PUMP/MOTOR - OPERATION, WASHER
. . . 8R-19
PUMP/MOTOR - REMOVAL, WASHER
....8R-19
QUARTER TRIM PANEL - INSTALLATION
. 23-159QUARTER TRIM PANEL - REMOVAL.....23-159
QUARTER WINDOW - INSTALLATION....23-172
QUARTER WINDOW - REMOVAL........23-172
QUICK CONNECT FITTING -
DESCRIPTION.......................14-10
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-21
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE........................14-10
RACK - INSTALLATION, LUGGAGE......23-144
RACK - REMOVAL, LUGGAGE..........23-144
RADIAL-PLY TIRES - DESCRIPTION.......22-6
RADIATOR - CLEANING.................7-24
RADIATOR - DESCRIPTION..............7-22
RADIATOR - FAN - VISCOUS - CLEANING . . 7-29
RADIATOR - FAN - VISCOUS -
DESCRIPTION........................7-27
RADIATOR - FAN - VISCOUS -
INSPECTION.........................7-29
RADIATOR - FAN - VISCOUS -
INSTALLATION........................7-29
RADIATOR - FAN - VISCOUS -
OPERATION..........................7-27
RADIATOR - FAN - VISCOUS - REMOVAL . . . 7-28
RADIATOR - INSPECTION...............7-24
RADIATOR - INSTALLATION.............7-24
RADIATOR - REMOVAL.................7-23
RADIATOR CROSSMEMBER -
INSTALLATION......................23-146
RADIATOR CROSSMEMBER - REMOVAL . 23-146
RADIATOR FAN - ELECTRIC -
DESCRIPTION........................7-26
RADIATOR FAN - ELECTRIC -
INSTALLATION........................7-27
RADIATOR FAN - ELECTRIC -
OPERATION..........................7-26
RADIATOR FAN - ELECTRIC - REMOVAL . . . 7-26
RADIATOR PRESSURE CAP - CLEANING . . . 7-25
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-25
RADIATOR PRESSURE CAP - DIAGNOSIS
AND TESTING........................7-25
RADIATOR PRESSURE CAP -
INSPECTION.........................7-25
RADIATOR PRESSURE CAP - OPERATION . . 7-25
RADIO - DESCRIPTION.................8A-8
RADIO - INSTALLATION................8A-9
RADIO - OPERATION...................8A-8
RADIO - REMOVAL....................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION.................8A-9
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION...............8A-11
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION.................8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL...................8A-10
RAIL - DESCRIPTION, FUEL............14-21
RAIL - INSTALLATION, FUEL............14-24
RAIL - OPERATION, FUEL..............14-21
RAIL - REMOVAL, FUEL...............14-22
RAIL WEATHERSTRIP/RETAINER -
INSTALLATION, SIDE.................23-186
RAIL WEATHERSTRIP/RETAINER -
REMOVAL, SIDE....................23-186
RAMP - INSTALLATION, WIPER ARM
PARK..............................8R-43
RAMP - REMOVAL, WIPER ARM PARK . . . 8R-43
RANGE INDICATOR ILLUMINATION BULB
- INSTALLATION, TRANSMISSION........8L-83
RANGE INDICATOR ILLUMINATION BULB
- REMOVAL, TRANSMISSION
...........8L-82
RANGE SENSOR - DESCRIPTION,
TRANSMISSION
.....................21-168
RANGE SENSOR - OPERATION,
TRANSMISSION
.....................21-168
RATINGS, GAS ENGINES - GENERATOR
. . . 8F-23
RBI AXLE - INSTALLATION, 198
..........5-28
RBI AXLE - REMOVAL, 198
..............5-27
READING LAMP BULB - INSTALLATION
. . . 8L-79
READING LAMP BULB - REMOVAL
.......8L-79
READING LAMP SWITCH -
INSTALLATION
.......................8L-80
READING LAMP SWITCH - REMOVAL
.....8L-80
READING LAMP UNIT - INSTALLATION
. . . 8L-81
READING LAMP UNIT - REMOVAL
.......8L-81
REAR - DESCRIPTION
..................2-16REAR - INSTALLATION, CRANKSHAFT
OIL SEAL............................9-48
REAR - INSTALLATION, PROPELLER
SHAFT...............................3-7
REAR - INSTALLATION, SEAT..........23-168
REAR - INSTALLATION, SEAT BACK.....23-168
REAR - INSTALLATION, SEAT BACK
COVER............................23-169
REAR - INSTALLATION, SEAT BACK
CUSHION..........................23-170
REAR - INSTALLATION, SEAT BACK
FRAME............................23-171
REAR - INSTALLATION, SEAT CUSHION . . 23-171
REAR - REMOVAL, CRANKSHAFT OIL
SEAL...............................9-48
REAR AXLE - 198RBI - DESCRIPTION.....3-49
REAR AXLE - 198RBI - INSTALLATION.....3-54
REAR AXLE - 198RBI - OPERATION.......3-49
REAR AXLE - 198RBI - REMOVAL........3-54
REAR AXLE - 8 1/4 - ADJUSTMENTS......3-92
REAR AXLE - 8 1/4 - DESCRIPTION.......3-86
REAR AXLE - 8 1/4 - INSTALLATION......3-91
REAR AXLE - 8 1/4 - OPERATION.........3-86
REAR AXLE - 8 1/4 - REMOVAL..........3-91
REAR AXLE - SPECIFICATIONS...........3-62
REAR AXLE, SPECIAL TOOLS............3-63
REAR AXLE, SPECIFICATIONS............3-98
REAR BRAKE HOSE - INSTALLATION......5-10
REAR BRAKE HOSE - REMOVAL...........5-9
REAR CENTER SEAT BELT &
RETRACTOR - INSTALLATION...........8O-33
REAR CENTER SEAT BELT &
RETRACTOR - REMOVAL..............8O-32
REAR CHECK VALVE - DESCRIPTION.....8R-34
REAR CHECK VALVE - INSTALLATION....8R-35
REAR CHECK VALVE - OPERATION.......8R-34
REAR CHECK VALVE - REMOVAL........8R-34
REAR CROSSMEMBER - INSTALLATION....13-7
REAR CROSSMEMBER - REMOVAL.......13-7
REAR DOOR OUTER BELT MOLDING -
INSTALLATION......................23-186
REAR DOOR OUTER BELT MOLDING -
REMOVAL.........................23-186
REAR DOOR SCUFF PLATE -
INSTALLATION......................23-160
REAR DOOR SCUFF PLATE - REMOVAL . . 23-160
REAR DRUM BRAKE - ADJUSTMENT......5-12
REAR DRUM BRAKE - DESCRIPTION......5-10
REAR DRUM BRAKE - OPERATION........5-11
REAR FASCIA - INSTALLATION...........13-2
REAR FASCIA - REMOVAL...............13-2
REAR FASCIA SUPPORT - INSTALLATION . . 13-3
REAR FASCIA SUPPORT - REMOVAL......13-3
REAR FOG LAMP INDICATOR -
DESCRIPTION.......................8J-27
REAR FOG LAMP INDICATOR -
OPERATION.........................8J-27
REAR FOG LAMP RELAY - DESCRIPTION . . 8L-56
REAR FOG LAMP RELAY - DIAGNOSIS
AND TESTING.......................8L-57
REAR FOG LAMP RELAY -
INSTALLATION.......................8L-58
REAR FOG LAMP RELAY - OPERATION . . . 8L-57
REAR FOG LAMP RELAY - REMOVAL.....8L-58
REAR GLASS HEATING GRID REPAIR -
STANDARD PROCEDURE...............8G-4
REAR HVAC CONTROL ASSEMBLY
WINDOW DEFOGGER FUNCTION -
DIAGNOSIS AND TESTING..............8G-9
REAR LAMP BULB - INSTALLATION......8L-59
REAR LAMP BULB - REMOVAL..........8L-58
REAR LAMP UNIT - INSTALLATION......8L-60
REAR LAMP UNIT - REMOVAL..........8L-59
REAR MOUNT - INSTALLATION..........9-57
REAR MOUNT - REMOVAL..............9-57
REAR OUTBOARD SEAT BELT &
RETRACTOR - INSTALLATION...........8O-34
REAR OUTBOARD SEAT BELT &
RETRACTOR - REMOVAL..............8O-33
REAR OUTPUT SHAFT SEAL -
INSTALLATION
......................21-212
REAR OUTPUT SHAFT SEAL - REMOVAL
. 21-210
REAR SEAL AREA LEAKS - DIAGNOSIS
AND TESTING
........................9-61
REAR SEAT BACK LATCH / LOCK -
INSTALLATION, FOLDING
.............23-170
REAR SEAT BACK LATCH / LOCK -
REMOVAL, FOLDING
.................23-170
20 INDEXKJ
Description Group-Page Description Group-Page Description Group-Page
Page 1764 of 1803
SPARK PLUG - OPERATION.............8I-12
SPARK PLUG - REMOVAL..............8I-15
SPARK PLUG CABLE RESISTANCE, 2.4L....8I-3
SPARK PLUG CONDITIONS - DIAGNOSIS
AND TESTING........................8I-13
SPARK PLUGS, SPARK PLUG -
CLEANING..........................8I-15
SPARK PLUGS, SPECIFICATIONS..........8I-3
SPEAKER - DESCRIPTION..............8A-13
SPEAKER - INSTALLATION.............8A-15
SPEAKER - OPERATION...............8A-14
SPEAKER - REMOVAL.................8A-14
SPECIAL TOOLS - 3.7L ENGINE..........9-15
SPECIAL TOOLS - 8 1/4 AXLE...........3-98
SPECIAL TOOLS - BASE BRAKES..........5-7
SPECIAL TOOLS - BODY................23-5
SPECIAL TOOLS - COOLING.............7-14
SPECIAL TOOLS - FRONT AXLE..........3-34
SPECIAL TOOLS - FRONT SUSPENSION.....2-8
SPECIAL TOOLS - FUEL SYSTEM.........14-6
SPECIAL TOOLS - OUTER TIE ROD END
REMOVAL TOOL.....................19-15
SPECIAL TOOLS - POWER
DISTRIBUTION SYSTEMS............8W-97-2
SPECIAL TOOLS - POWER STEERING
PUMP.............................19-20
SPECIAL TOOLS - REAR AXLE...........3-63
SPECIAL TOOLS - RFE TRANSMISSION....21-120
SPECIAL TOOLS - STEERING COLUMN....19-8
SPECIAL TOOLS - WIRING/TERMINAL . 8W-01-10
SPECIAL TOOLS, BATTERY SYSTEM.......8F-7
SPECIFICATIONS, BATTERY SYSTEM......8F-6
SPECIFICATIONS, BRAKES - ABS.........5-33
SPECIFICATIONS, CHARGE CAPACITY.....24-42
SPECIFICATIONS, CLUTCH...............6-5
SPECIFICATIONS, DIAGNOSIS AND
TESTING............................22-8
SPECIFICATIONS, FLUID CAPACITIES.......0-4
SPECIFICATIONS, FRAME DIMENSIONS....13-3
SPECIFICATIONS, FRONT AXLE...........3-33
SPECIFICATIONS, GAP AND FLUSH.....23-116
SPECIFICATIONS, IGNITION TIMING.......8I-2
SPECIFICATIONS, LAMPS/LIGHTING -
EXTERIOR..........................8L-15
SPECIFICATIONS, LAMPS/LIGHTING -
INTERIOR..........................8L-71
SPECIFICATIONS, NV1500..............21-30
SPECIFICATIONS, OPENING DIMENSIONS . 23-111
SPECIFICATIONS, PAINT CODES........23-162
SPECIFICATIONS, REAR AXLE............3-62
SPECIFICATIONS, REMOTE KEYLESS
ENTRY TRANSMITTER.................8N-9
SPECIFICATIONS, SEALER LOCATIONS....23-87
SPECIFICATIONS, SPECIFICATIONS.......24-10
SPECIFICATIONS, STANDARD
PROCEDURE.........................23-4
SPECIFICATIONS, TORQUE..............13-6
SPECIFICATIONS, WELD AND
STRUCTURAL ADHESIVE LOCATIONS......23-9
SPEED CONTROL - DESCRIPTION........8P-1
SPEED CONTROL - OPERATION..........8P-1
SPEED CONTROL - TORQUE.............8P-2
SPEED SENSOR - DESCRIPTION, INPUT . 21-143
SPEED SENSOR - DESCRIPTION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, FRONT
WHEEL.............................5-34
SPEED SENSOR - INSTALLATION, INPUT . 21-143
SPEED SENSOR - INSTALLATION,
OUTPUT...........................21-152
SPEED SENSOR - INSTALLATION, REAR
WHEEL.............................5-35
SPEED SENSOR - OPERATION, INPUT . . . 21-143
SPEED SENSOR - OPERATION, OUTPUT . . 21-152
SPEED SENSOR - REMOVAL, FRONT
WHEEL.............................5-34
SPEED SENSOR - REMOVAL, INPUT.....21-143
SPEED SENSOR - REMOVAL, OUTPUT . . . 21-152
SPEED SENSOR - REMOVAL, REAR
WHEEL.............................5-35
SPEEDOMETER - DESCRIPTION
.........8J-32
SPEEDOMETER - OPERATION
...........8J-32
SPLASH SHIELD - INSTALLATION,
FRONT WHEELHOUSE
................23-143
SPLASH SHIELD - INSTALLATION, REAR
WHEELHOUSE
......................23-144
SPLASH SHIELD - REMOVAL, FRONT
WHEELHOUSE
......................23-143SPLASH SHIELD - REMOVAL, REAR
WHEELHOUSE......................23-144
SPLICE INFORMATION - DESCRIPTION,
CONNECTOR, GROUND..............8W-01-7
SPLICING - STANDARD PROCEDURE,
WIRE...........................8W-01-14
SPRING - INSTALLATION...........2-13,2-18
SPRING - REMOVAL...............2-13,2-18
SPRINGS - DESCRIPTION, VALVE.....9-29,9-38
SPRINGS - INSTALLATION, VALVE....9-29,9-38
SPRINGS - REMOVAL, VALVE........9-29,9-38
STABILIZER BAR - INSTALLATION....2-14,2-19
STABILIZER BAR - REMOVAL........2-14,2-19
STABILIZER BAR BUSHINGS -
INSTALLATION.........................2-9
STABILIZER BAR BUSHINGS - REMOVAL....2-9
STABILIZER LINK - INSTALLATION........2-14
STABILIZER LINK - REMOVAL............2-14
STAKING - STANDARD PROCEDURE,
HEAT ...............................23-3
STARTER MOTOR - DIAGNOSIS AND
TESTING...........................8F-39
STARTER MOTOR - INSTALLATION.......8F-41
STARTER MOTOR - REMOVAL..........8F-39
STARTER MOTOR, GAS POWERED.......8F-39
STARTER MOTOR RELAY - DESCRIPTION . 8F-41
STARTER MOTOR RELAY -
INSTALLATION.......................8F-43
STARTER MOTOR RELAY - OPERATION.....8F-42
STARTER MOTOR RELAY - REMOVAL.....8F-43
STARTER RELAY - DIAGNOSIS AND
TESTING...........................8F-42
STARTING PROCEDURE - STANDARD
PROCEDURE, JUMP....................0-5
STARTING SYSTEM - DESCRIPTION......8F-32
STARTING SYSTEM - DIAGNOSIS AND
TESTING...........................8F-33
STARTING SYSTEM - INSPECTION.......8F-37
STARTING SYSTEM - OPERATION........8F-32
STATE DISPLAY TEST MODE -
DESCRIPTION........................25-2
STEERING - DESCRIPTION..............19-1
STEERING - OPERATION................19-1
STEERING COLUMN, SPECIAL TOOLS.....19-8
STEERING FLOW AND PRESSURE -
DIAGNOSIS AND TESTING, POWER.......19-3
STEERING LINKAGE - STANDARD
PROCEDURE........................19-16
STEERING PRESSURE SWITCH -
DESCRIPTION, POWER................19-22
STEERING PRESSURE SWITCH -
INSTALLATION, POWER...............19-22
STEERING PRESSURE SWITCH -
OPERATION, POWER..................19-22
STEERING PRESSURE SWITCH -
REMOVAL, POWER...................19-22
STEERING PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER.......19-18
STEERING PUMP, SPECIAL TOOLS -
POWER............................19-20
STEERING SYSTEM - DIAGNOSIS AND
TESTING, POWER.....................19-1
STEERING SYSTEM - DIAGNOSIS AND
TESTING, SUSPENSION.................2-1
STEERING WHEEL - INSTALLATION......19-12
STEERING WHEEL - REMOVAL..........19-12
STOP LAMP BULB - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP BULB - REMOVAL, CENTER
HIGH MOUNTED.....................8L-18
STOP LAMP UNIT - INSTALLATION,
CENTER HIGH MOUNTED..............8L-19
STOP LAMP UNIT - REMOVAL, CENTER
HIGH MOUNTED.....................8L-19
STRAP - DESCRIPTION, RADIO NOISE
SUPPRESSION GROUND................8A-9
STRAP - INSTALLATION, CHECK . 23-121,23-128,
23-135
STRAP - INSTALLATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-11
STRAP - OPERATION, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRAP - REMOVAL, CHECK
.....23-121,23-128,
23-135
STRAP - REMOVAL, RADIO NOISE
SUPPRESSION GROUND
...............8A-10
STRIKER - INSTALLATION, GLOVE BOX
LATCH
............................23-149STRIKER - INSTALLATION, HOOD AJAR
SWITCH............................8Q-14
STRIKER - INSTALLATION, LATCH......23-124,
23-132,23-137
STRIKER - INSTALLATION, REAR SEAT
BACK LATCH.......................23-171
STRIKER - REMOVAL, GLOVE BOX
LATCH ............................23-148
STRIKER - REMOVAL, HOOD AJAR
SWITCH............................8Q-13
STRIKER - REMOVAL, LATCH . . . 23-124,23-132,
23-137
STRIKER - REMOVAL, REAR SEAT BACK
LATCH ............................23-170
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS, WELD................23-9
STRUCTURAL COVER - DESCRIPTION.....9-55
STRUCTURAL COVER - INSTALLATION.....9-55
STRUCTURAL COVER - OPERATION.......9-55
STRUCTURAL COVER - REMOVAL........9-55
STUDS - INSTALLATION...............22-11
STUDS - REMOVAL...................22-11
SUCTION LINE - INSTALLATION, A/C.....24-49
SUCTION LINE - REMOVAL, A/C.........24-48
SUN VISOR - INSTALLATION..........23-160
SUN VISOR - REMOVAL..............23-160
SUN VISOR SUPPORT - INSTALLATION . . 23-160
SUN VISOR SUPPORT - REMOVAL......23-160
SUNROOF - DESCRIPTION............23-175
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-178
SUNSHADE - INSTALLATION...........23-179
SUNSHADE - REMOVAL..............23-179
SUPPLEMENTAL RESTRAINT
DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER A.........8O-6
SUPPLEMENTAL RESTRAINT SYSTEM -
DIAGNOSIS AND TESTING..............8O-6
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE, HANDLING
NON-DEPLOYED......................8O-6
SUPPLIES - DESCRIPTION, 5 VOLT......8E-13
SUPPLIES - OPERATION, 5 VOLT........8E-15
SUPPORT - INSTALLATION, REAR
FASCIA..............................13-3
SUPPORT - INSTALLATION, SUN VISOR . . 23-160
SUPPORT - REMOVAL, REAR FASCIA......13-3
SUPPORT - REMOVAL, SUN VISOR.....23-160
SUPPORT BRACKET - INSTALLATION,
REARVIEW MIRROR.................23-161
SUPPORT CYLINDER - INSTALLATION . . . 23-120
SUPPORT CYLINDER - INSTALLATION,
FLIP-UP GLASS.....................23-139
SUPPORT CYLINDER - REMOVAL.......23-120
SUPPORT CYLINDER - REMOVAL,
FLIP-UP GLASS.....................23-139
SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO NOISE............8A-9
SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO NOISE...........8A-11
SUPPRESSION GROUND STRAP -
OPERATION, RADIO NOISE.............8A-10
SUPPRESSION GROUND STRAP -
REMOVAL, RADIO NOISE..............8A-10
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET............9-9
SUSPENSION - DIAGNOSIS AND
TESTING, REAR.......................2-17
SUSPENSION AND STEERING SYSTEM -
DIAGNOSIS AND TESTING...............2-1
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - DESCRIPTION, UPPER......2-20
SUSPENSION ARM, BUSHINGS, AND
BALL JOINT - OPERATION, UPPER........2-20
SUSPENSION, SPECIAL TOOLS - FRONT....2-8
SWING GATE - INSTALLATION.........23-138
SWING GATE - REMOVAL.............23-138
SWING GATE BELTLINE WEATHERSTRIP
- INSTALLATION....................23-186
SWING GATE BELTLINE WEATHERSTRIP
- REMOVAL
........................23-186
SWING GATE OPENING WEATHERSTRIP
- INSTALLATION
....................23-186
SWING GATE OPENING WEATHERSTRIP
- REMOVAL
........................23-186
SWITCH - DESCRIPTION
................8P-5
SWITCH - DESCRIPTION, A/C HIGH
PRESSURE
.........................24-17
KJINDEX 25
Description Group-Page Description Group-Page Description Group-Page
Page 1782 of 1803
JEEP LIBERTY 2002
2.4L ENGNOTE: All Parts in this section are included in R&R SteerinaColumn unless noted otherwise.
WHEEL & TRIM
2
~fI::;~~ ~/\1f'R14
151
r-54
4~3
~~29
~
5004-09529
1 Mount, Eng R 52059252AAL 52059253AA2 Mount, Trans 52059299AA3 Crossmember, Trans 52128592AA#/ncludes R&R Trans Mount
2
1~18.6 142.00.8 109.00.7 123.00'1.1 40.4519,.
004-09527
004-09910 ~
1 Wheel, Steeringll UR71 DX9AA m .5 136.00llAdditional Parts &lor Dealer Contact Required2 Module, Driver Air Bag-See Air Bag System Section3 Switch, Remote Radio R 560423f2AB m #.4 14.25L 56042313AB m #.4 13.50#R&R Both Sides .64 Switch, Cruise ControlLimited Mode! R 56010358AB m .3 24.60L 56010359AB m .3 24.60IRenegade, Sport Model R 56010088AC m .3 14.60L 56010089AC m .3 14.605 Clockspring-See Air Bag System Section
3.7L ENG
f17~
COLUMN
2
3~m 1.5m 2.5R&I Steering Column O/H Steering Column (Includes R&I)
9-AA
5 Belt, Timing 4621844 m 3.8 78.606 Tensioner, Timing Belt 53010371AA m #.2 0.001I 7 Pulley, Idler 53013324AA m #.1 20.458 Gear, Camshaft (2) 4667609 m #.2 24.109 Gear, Crankshaft 4621918 m #.2 18.35#W/Timing Belt Removed10 Cover, Inner Timing 53010482AB m 39.50 004-0953011 Cover Valve 53010493AC m .7 87.6012 Cap, Oil Filler 4648831AA 6.85 1 Mount, Eng R 52059226AA13 Gasket, Valve Cover 4777478 m 84.45 L 52059227AA14 Dipstick, Eng Oil 53010494AA 6.10 2 Mount, Trans15 Tube, Eng Dipstick 53010476AB .5 9.6Q 2 WD16 Pan, Eng Oil 53010491AA m 1.6 65.85 Man Trans 52059309AA17 Plug, Drain 6035417 5.25 Auto Trans 52059306AA18 Gasket, Eng Oil Pan 4621579 m 26.20 4 WD19 Pan, Trans vii Man Trans 52059324AA2 WD 4800078AA m.9 28.20 Auto Trans 52002334AB4 WD 5013681AA m.9 30.85 3 Crossmember, Trans 52058643AF#Includes R&R Trans Mount
.6 102.00.8 104.00
.7.7
.7.7'1.1
4 '
7~ 10 8-'-/
~J=::~~~$=l=~~::~
~ 114-12
5-"'1 1
6*
2~ ~
m 10.6R&I Enginefrrans Assy
32S
Q>--E
1 b~4
~A56010126AD
m .6 75.00I56010125AD m .6 75.0056010158AC m .5 29.204793576 m.7 5.205GK59DX9AB m #.3 6.20
96.206.25
6.206.20
5.45
.2-{
.
.3 114.00.3 37.9517.9517.95
11
~
004-09911
1 Switch Combinationw/Fog Lampsw/o Fog LamRs2 Switch, Hazard3 Switch, Ignition4 Cover, Upper Column5 Cover, Lower ColumnMan TranswfTilt 5GE04DX9AB m #.3w/o Tilt 5GEOODX9AB m #.3Auto Transwmlt 5GE08DX9AB m #.3w/o Tilt 5GE06DX9AB m #.3#R&R Complete6 Trim, Ignition Cylinder 55314965AB m7 Shaft, Upper1jMan Trans 10To 12-16-01 55314993AB m 2.0 389.00 004-09528
From 12-17-01 5057077AA m 2.0 425.00Auto Trans Damper, Crankshaft N.A. m 1.0 0.00To 12-16-01 55314994AB m 2.0 350.00 1 Cover, Timing 53021238AA m 272.00From 12-17-01 5057078AA m 2.0 420.00 2 Cover, Valve R 53020996 m #.8 22.45l1Additional Parts &/or Dealer Contact Required L 53020995 m #.8 22.858 Shaft, Lower 55315022AB m .8 330.00 #R&R Both Sides 1.29 Bracket, No.1 Column 55314992AA m 9.85'3 Gasket, Valve Cover AiL 53020992-1 m 24.0010 Bracket, No.2 Column 55314987AA m 154.00 4 Housing, Oil Filler 53020890 m 26.1011 Bracket, Shaft 55315003AB m 11.00 5 Gasket, Oil Filler Housing 53020889AB 4.8512 Bracket, Lower Column 55315009AA m 8.85 6 Cap, 011 Filler 53032389AC 5.107 Dipstick, En~ Oil 53021026AE 1.70I8 Tube, Eng I?lpstick 53021274AE .5 4.259 Pan, Eng 011 53021000AB m 2.7 69.20Gasket, Eng Oil Pan 53021001 m 16.7010 Plug, Drain 6504894AA 5.25111 Pan, Trans Oil2 WD 4800078AA m 1.3 28.204 WD 5013681AA m 1.3 30.85
2.4L ENG
R&I Air Cleaner Assy.4
1~
2~-l1.b-!6it
3~~ 004-0953,
1 Cleaner Assy.. Air 53013102AAElement, Air "Ieane~ 5019443AATube, Air Cleane~ 53013093AA1llncluded w/Air Cleaner Assy2 Tube, Inlet 53013101AA3 Bracket, Air Cleaner 53013473AAGrommet, Air Cleaner 53013357AA
Use Procedure Explanation 12 with the following text..4 113.00.2 14.603.75
.2 51.0025.252.70
2.4L ENG
m 7.4R&I Engine/Trans Assy
Illustration Located in Next Column3.7L ENG
.4R&I Air Cleaner Assy6503553 3.2053010477AA m .9 47.9553010483AA m .3 11.85153010484AA m #1.3 12.35"nc'udes R&R Crankshaft Pulley
1 Boll,
CH568
~~~10/;1
97.3572.25
115.0067.8595.00:v
Page 1784 of 1803
Starter2.4L Eng3.7L Eng
STARTER Cont'd
56041436M m .9 159.0056041641AC m 1.8 159.0035 I-
r~..:::---~ ~;i:i~:~'"
4~
Use Procedure Explanation 13 with the following tex!.R&IWindshield ...#2.7#Includes Clean Up Old Adhesive as Necessary
5 ~8
~~~~ -,
S-(::~:~~::~~:::::::~ ,,~(" p-~~ ~
\\\
f,
~
'~
):1
004-09541
1 Cover, Cowl 55155850AB.3 102.002 Pin, Cowl (4) 6501925 1.853 Seal, Cowl 55235927AA.1 16.254 Panel, Dash 55177300AB #7.0 127.00#W/Plenum Panel Removed Deduct 2.05 Panel, Plenum 55176767AC 7.0 270.00
\\\
4~1'"~
JEEP LIBERTY 2002
ELECTRICALCont'd2211 racket, Instrument anel9- 12 Bracket, Hush Panel 78 7.60
113 Kit, Radio Bracke~ 5072596M 11.701]lncludes Both Sides14 Bracket, Audio Equipment 5072606M 10.4515 Striker} Glove Box Latch 5072605M 25.4516 Brk! KI!t Passenger Air Bag-See Air Bag System Section11 Latch, ulove BoxSlate Gray WQ54XDVM.1 35.50Taupe WQ54WL8AA.1 24.8518 Module, PassenQer Air Bag-See Air Bag System Section19 Bracket, Lower Steeling Column 5531498TAA 154.0020 Box, GloveSlate Gray WC86XDVAA #.2 219.00Taupe WC86WL8AA #.2 219.00#Includes R&R Glove Box Latch21 Bezel, CenterLimited Model WA96DX9AA.3 92.75Renegade, Sport Model 5072479AA .3 180.0022 Knob, Li9hter 4685536 12.0023 Outlet, Lighter 4793554 11.0024 Ashtray WA97DX9AA 25.0025 SpeakerStandard AiL 56038610AC 43.00Premium AiL 56038594AC 73.0026 Bracket, UpperSt~ring Column 55314992AA 9.85
~/-
~313028
r:l-32I27
8-34 004-09924
2
7
5WIPER SYSTEM
213 I!
""""",~~~~-~~~4
5
~,..~6
,--d
~ :: 1
11~~~ ~ 19 ~14 .7
21~h13 4 1822 r:13 IIII ~ L16 15~ 18!Jj,j17~ 'j;--16 ~-" ~24 ~ ~
1~20 004-09923
7lf26--
?7 Cluster Ass~Black 56010151AF m .9 445.00Chrome 56010461AF m .9 454.00llAdditional Palts &/or Dealer Contact Required28 Lens, Cluster (a)Black 4728962AB m 1.0 0.00Chrome 4832731AB m 1.0 46.45la) Included wlCluster Assy29 RadioCode RBP 56038586AD.5 650.00Code RBY 56038583AD.5 0.00Code RBB 56038588AG.5 390.00Code RAD 56038585AD.5 1170.00Code RBK 56038589AH.5 460.00Code RBT 56038584AD.5 0.0030 Changer, CD 82203465 .5 345.00131 Cable, CD Changer 56038596AE 37.7032 Switch, Mirror 56010093AA #.2 22.95#Included in R&R Left Front Door Trim Panel, NotIncluded in R&R Instrument Panel33 Switch;, Climate ControlI wi Nv 55037533AB m .5 80.00wlo NC 55037531AB m .5 62.95134 Knob, Climate Controlll 5069169AA 1.451]As Required
8004-09540
on
6--<:~
#1.1
,-"-;:;;;;;;::~4~10 1
WD851DVAAWD851LSAA
WD581DVAAWD581L8AA
WD591DVAAWD591L8AB5072905AA5072906AA
.6 29.35.6 29.35
.6 43.00.6 43.00
#.2 92.85#.2 92.85#.2 10.00#.2 118.00
Use Procedure Explanations 14 and 28 with the following text.Refinish Dash Panel 1.5Refinish Plenum Panel 1.0
Labor Times Shown are for Replacement with New OEM Undamaged Parts on New Undamaged Vehicles.Comments or suggestions? Need assistance? Call 1.800-854-7030 or 8!;8/578-6550, Ext 8220. Fax 1-888-256-7969 or 858/549-0629.570CH
' 2 004-09922
1 Glass, WindshieldChrysler 55235913AC #2.3 0.00 ...NAGS c DW01449GBN #2.3 958.30 Use Procedure Explanation 14 with the following text.#Includes Clean Up Otd Adhesive as Necessary R&llnstrument Panel.. m #5.02 Spacer, Windshield /4) 55360509AA .35 #tncludes R&I Steering Column & Floor Console3 Mould!ng. Upper W/$ 55235917AB 9.60 NOTE: All Parts in this section are included in R&R4 Moulding. Side WIS R 55360052AB .2 58.85 Instrument Panel unless noted otherwiseL 55360053AB .2 58.85 .
5 Mirror, Rear View 4805332AB .2 19.45 16 Button, Rear View Mirror 55076401 8.25 25-{!:Q7 Moulding, Inr W/S Garnish R 5GM92TL2AC .3 46.35 6-0L 5GM93TL2AC .3 46.3598 Visor, Sun 5Illuminated R UY66TL2AA .2 103.00 I 10 6L UY67TL2AA .2 106.00 ~Non-Illuminated R UY64TL2AA .2 61.95 ~ 6 1L UY65TL2AA .2 63.70 ()\4Clip, Visor R/L 5072343AA 2.60
4 Arm, Wiper R 5666970AAL 5066968AA#Includes R&R Wiper Blade5 Module, Wiper 55155895AA6 Reservoir, Washer 5066867AA#Includes R&I/R&R Air Cleaner Assy7 Cap, Reservoir 5066881AA8 Pump, WasherTo 8-3-01 5066880AAFrom 8-3-01 5018129ACGrommet Pump 5011809AA9 Sensor, Fluid Level 4882797Grommet, Sensor 5013755AANozzle, Washer AiL 55155854AB#Included in R&R Cowl Cover
Use Procedure Explanation 14 with the following text.R&IFloorConsole .3
NOTE: All Parts in this section are included in R&R FloorConsole unless noted otherwise.
2
~~~~~~
,~-.- ,-,..1'70 3 Door, Passenger Air Bag-See Air Bag System Section1 16'60 4 Panel, Instrument.116'60Slate Gray..To 6-14-01 WC85XDVAA m #6.5 517.00#.2 24.10 From 6-14-01 WC85XDVAB m#6.5 517.00#.2 26.00 Taupe
To 6-14-01 WC85WL8AA m #6.5 517,0078,35 From 6-14-01 WC85WL8AB m #6.5 517,0078.50 #Includes R&I Steering Column & Floor Console25005 Bracket, Instrument Panel R 5073523AA 39.95, L 5072615AA 30,8588 45 6 Grille, Instrument Panel (4) WC88DX9AA .1 0,00.7 Cover, Instrument Panel531.1100Slate Gray R 5GN55XDVAD .1 10,95, L 5GK19XDVAD .1 17,5094,2005 Taupe R 5GN55WL8AD .1 10.95, L 5GK19WL8AD .1 17,50#.2 10,00 8 Bezel, No.1 Instrument PanelLimted Model WB02DX9AA.2 30,70 004-09544Renegade, Sport ModelSlate Gray WB021DVAA.2 30.70 1 Console, FloorTaupe WB021L8AA.2 30,70 Man Trans9 Bezel, No.2 Instrument Panel Slate GrayLimited Model WB03DX9AA.1 25,45 TaupeRenegade, Sport Model Auto TransSlate Gray WB031DVAA.1 25.45 Slate GrayTaupe WB031 L8AA .1 25.45 Taupe10 Bezel, No.3 Instrument Panel 2 Lid, ConsoleLimited Model WB05DX9AA.1 22.10 Slate Grayi Renegade, Sport Model TaupeISlate Gray WB051DVAA.1 22.10 3 Latch, LidTaupe WB051l8AA.1 22.10 4 Hinge, Lid