turn signal bulb JEEP LIBERTY 2007 KJ / 1.G Owners Manual
[x] Cancel search | Manufacturer: JEEP, Model Year: 2007, Model line: LIBERTY, Model: JEEP LIBERTY 2007 KJ / 1.GPages: 417
Page 119 of 417
Turn Signals
Move the multi-function control lever up or down and
the arrows on each side of the instrument cluster flash to
show proper operation of the front and rear turn signal
lights. You can signal a lane change by moving the lever
partially up or down without moving beyond the detent.
If either light flashes at a very fast rate, check for a
defective outside light bulb. If an indicator fails to light
when the lever is moved, it would suggest that the fuse
or indicator is defective.
NOTE:A tone will chime if the turn signals are left on
for more than 2 miles (3.2 km).
High Beam Switch
Pull the multi-function control lever towards you to
switch the headlights to HIGH beam. Pull the multi-
function control lever a second time to switch the head-
lights to LOW beam. The “High Beam Indicator Light”
will illuminate when the high beams are on.
Passing Light
You can signal another vehicle with your headlights by
lightly pulling the multi-function control lever toward
the steering wheel. This will cause the headlights to turn
on at high beam and remain on until the lever is released.
The “High Beam Indicator Light” will illuminate when
the high beams are on.
Interior Lights
The overhead lights will come on when a door is opened,
and when the rotating ring on the multi-function control
lever is in a position other than OFF. They may also be
turned on by rotating the control for the dimmer switch
on the multi-function control lever fully upward or by
pressing the “Unlock” button on the keyfob.
The overhead lights will automatically turn off in about 8
minutes if a door is left open or the dimmer control is left
in the dome light position. Turn the ignition switch ON to
restore the overhead light operation.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119
3
Page 314 of 417
▫Driveline And Steering Component
Lubrication..........................331
▫Body Lubrication.....................331
▫Windshield Wiper Blades................331
▫Windshield Washers...................332
▫Exhaust System......................333
▫Cooling System.......................333
▫Hoses And Vacuum/Vapor Harnesses.......338
▫Fuel System Connections................339
▫Brake System........................339
▫Clutch Hydraulic System —
Manual Transmission Only..............342
▫Front/Rear Axle Fluid..................342
▫Transfer Case........................343▫Manual Transmission..................344
▫Automatic Transmission................345
▫Appearance Care And Protection
From Corrosion......................347
Fuse Panel...........................353
▫Interior Fuses........................353
▫Underhood Fuses
(Power Distribution Center)..............356
Vehicle Storage........................361
Replacement Bulbs......................361
Bulb Replacement......................362
▫Head Light..........................362
▫Front Turn Signal.....................363
▫Front Fog Light (Front Fascia Mounted).....364
314 MAINTAINING YOUR VEHICLE
Page 362 of 417
Exterior Lights Bulb Type
Front Side Marker........................ 168
Headlights..........................9007QL
Rear License Plate Light.................... 168
Rear Stop/Tail Lights...............3157 P27/7W
Rear Turn Signal Lights (2).........3757 APY27/7W
NOTE:Numbers refer to commercial bulb types that
can be purchased from your authorized dealer.
If a bulb needs to be replaced, visit your authorized
dealer.
BULB REPLACEMENT
Head Light
1. Open the hood.
2. Reach behind the headlamp unit in the engine com-
partment to access the headlamp bulb lock ring.3. Firmly grasp the lock ring on the back of the headlamp
unit housing.
4. Rotate the lock ring on the back of the headlamp
housing counter-clockwise to unlock it.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean
the bulb with rubbing alcohol.
5. Disconnect the electrical connector and replace the
bulb.
362 MAINTAINING YOUR VEHICLE
Page 363 of 417
Front Turn Signal
1. Remove the screw from the turn signal/park lamp
unit.
2. Pull the inboard side of the lamp away enough to
disengage the tab that secures the outboard side of the
lamp from the slot in the front bumper fascia.3. Rotate the bulb socket counter-clockwise to unlock it.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean
the bulb with rubbing alcohol.
4. Disconnect the electrical connector and replace the
bulb.
MAINTAINING YOUR VEHICLE 363
7
Page 365 of 417
Rear Tail, Stop, Turn Signal, and Back-Up Lights
1. Open the swing gate.
2. Remove the two Torx fasteners.
3. Remove rear lamp assembly.
4. Rotate the socket on the back of the lamp housing
counter-clockwise to unlock it.
5. Replace the bulb.
Center High Mounted Stop Light (CHMSL)
1. Remove the two screws securing the CHMSL.
2. Twist the bulb socket to remove from the CHMSL
housing.
3. Pull the bulb out of the socket.
4. Replace the bulb, reinstall the socket and reattach the
CHMSL.
MAINTAINING YOUR VEHICLE 365
7