ECU JEEP WRANGLER 2004 TJ / 2.G User Guide

TO OPEN AND CLOSE THE HOOD
To open hood, first release both hood latches.
Next, locate handle in middle of the front end of the
hood. Insert hand into gap between hood and radiator
support and lift up on handle to raise hood. You may
have to push down slightly on hood before lifting up on
handle. Insert the support rod into the slot in the radiator
support.To close the hood, remove the support rod from the
radiator support and place it in the retaining clip. Lower
the hood slowly, then let it drop the last few inches.
Secure both of the hood latches.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55
3

STORAGE
Glove Compartment
To unlock the glove compartment, insert the key and
turn. To open, pull the latch up.
Console Storage Compartment Ð If Equipped
To unlock, insert key and turn. To open, press the latch
button.
Add-A-TrunkŸ Ð If Equipped
The factory-installed Add-A-TrunkŸ option provides a
secured compartment for parcels or equipment when the
tailgate is closed and locked. To gain access to this
compartment, simply open the tailgate and release the
spring loaded latch pins. The cover of the Add-A-
TrunkŸ can then be raised.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65
3

When the Add-A-TrunkŸ is not desired, it can be easily
removed from the rear compartment. Remove the four
knobs that secure the ªtrunkº to the body. Lift the
Add-A-TrunkŸ out and place the knobs in the molded-in
storage area. Storage space is also provided for the wheel
lock, and lock key tool.
Do not leave the Add-A-TrunkŸ loose in your vehicle.
Remove it and store it in a safe place.
DUAL TOP Ð IF EQUIPPED
If your vehicle is equipped with a Dual Top,you must
remove one of the tops from the vehicle.The soft top
was installed at the factory for shipping purposes only.
The soft top and the hard top are to be used indepen-
dently.Removal is mandatory to prevent any possible
wear and tear on the soft top, should both tops remain on
the vehicle at the same time. Failure to do so may void
your soft top warranty.
Removing The Soft Top
1. Locate and remove the 2 boxes that contain the
following items:
²right and left door frames
²door frame attachment knobs (4)
²right and left quarter windows
²rear tailgate window
2. Remove the hard top. Refer to ªHard Top Removalº in
this section.
3. Remove the soft top bow assembly pivot bracket
screws (2 per side) using a #30 Torxthead driver.
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

c. Lay the soft top back into the vehicle with the
curved portion of the bows facing upward.
d. Tap the knuckles on the side with a rubber mallet
to reattach them to the pivot bracket.
e. Screw the pivot screws back into place. Secure
them until they are snug being careful not to cross-
thread the screws.CAUTION!
Do not overtighten the screws. You can strip the
screws if they are overtightened.
5. Unsnap and remove the black boot cover. This cover
should be discarded. It was intended as a protective
cover for shipping only.
NOTE:A visual instruction sheet is enclosed in the dual
top wrap.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69
3

26. Close the header latches and position the sun visor.HARD TOP
CAUTION!
²The hard top is not designed to carry any addi-
tional loads such as roof racks, spare tires, build-
ing, hunting, or camping supplies, and/or lug-
gage, etc. Also, it was not designed as a structural
member of the vehicle, and thus cannot properly
carry any additional loads other than environmen-
tal (rain, snow, etc.).
²The hard top does not include any devices to
properly secure any loads on the roof, and any
damage (structural or surface finish) that occurs
due to any additional loading to the top area will
void the vehicle warranty.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

CAUTION!
Do not move your vehicle until the top has been
either fully attached to the windshield frame and
bodyside, or fully removed.
Hard Top Removal
1. Fold down the sun visors and move them to the side.
2. Unlatch the two hard top latches located at the top of
the windshield.3. Unbolt the six Torxthead screws which secure the
hard top to the vehicle using a #40 Torxthead driver.
CAUTION!
When removing the 2 front screws just rearward of
the doors, make sure that the nut does not fall into
the seat belt retractor. Grasp the nut to prevent this
from occurring.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79
3

7. Disconnect the washer hose and install the tethered
cap.
CAUTION!
Make sure storage cap is installed to prevent foreign
materials from entering tube and clogging system.
8. Disconnect the wire harness from the hard top by
pressing the tab at the side of the connector and pulling
to disconnect.
NOTE:If the red latch on the connector is locked, push
the red latch to the right until you can only see the latch
on one end (right) of the connector. This will unlock
connector tab, allowing the tab to be pressed down and
enabling the harness to be disconnected from the hard
top.
9. Remove the hard top from the vehicle.
10. Fold the harness back and secure it to the main
harness using the attached Velcrotstrap, to prevent the
harness from rattling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81
3

NOTE:If the doors are to be removed, pull the #4 fuse
from the fuse block to prevent dome lamp illumination.
Hard Top Installation
NOTE:
If the door frames are installed from soft top
usage, they must be removed prior to installation of the
hard top.
1. Inspect the hard top seals for damage and replace if
necessary.
2. Install the hard top using the same steps for removal
in reverse order.
NOTE:The hard top must be positioned properly to
ensure sealing. Set the hard top on the windshield frame
so that there is no overhang. Also, make sure that the
hard top is sitting flush with the body at the sides and
check to ensure that there is a uniform gap between the
lift glass and hard top.
SOFT TOP
CAUTION!
²The soft top is not designed to carry any addi-
tional loads such as roof racks, spare tires, build-
ing, hunting, or camping supplies, and/or lug-
gage, etc. Also, it was not designed as a structural
member of the vehicle, and thus cannot properly
carry any additional loads other than environmen-
tal (rain, snow, etc.).
²The soft top does not include any devices to
properly secure any loads on the roof, and any
damage (structural or surface finish) that occurs
due to any additional loading to the top area will
void any vehicle warranty.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

10. Remove SunriderŸ pins to release side rails from
brackets located on both door rails (Unlimited Models
Only).
11. Release the hook portion of the latches. Grasp the
side bow behind the header and lift the top back.12. As you begin to lower the top, wrap the sail panels so
that they rest on the roof of the vehicle.
NOTE:If your vehicle is equipped with a Dual Top,
ensure that the hard top wire harness is folded back and
secured to the main harness, using the attached Velcrot
strap, to prevent connector damage.
13. Make sure the sides of the top are folded inward as
the top continues to fold, and that the check straps are
clear of the vehicle.
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Unclip and move the sun visors to the side.
3. Release the header latches, and slide the plastic sleeves
forward.
4. Grasp the header and lift the top back. Make sure the
material is folded back as shown. Secure latches to plastic
retainer on header. Locate strap to secure the header to
the sport bar. Wrap strap around sport bar and hook to
header and tighten.5. Attach and reposition sunvisors.
To Lower
1. Remove strap from header and sport bar.
2. Release header latches from header retainer.
3. Unclip and move the sun visors to the side.
4. Grasp the front header and pull to the front of the
vehicle.
5. Slide plastic sleeve rearward over SunriderŸ link.
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE