airbag KIA CARNIVAL 2007 User Guide

DIAGNOSTIC TROUBLE CODES (DTC)
DTCFAULT DESCRIPTION PAGE
B1101 Battery Voltage too High
B1102 Battery Voltage too Low
B1328 Front Impact Sensor [Driver] Defect
B1329 Front Impact Sensor [Driver] Communication Error
B1333 Front Impact Sensor [Passenger] Defect
B1334 Front Impact Sensor [Passenger] Communication Error
B1346 Driver Airbag Resistance too High
B1347 Driver Airbag Resistance too Low

B1348Driver Airbag Circuit Short to Ground
B1349 Driver Airbag Circuit Short to Battery
B1352 Passenger Airbag Resistance too High
B1353 Passenger Airbag Resistance too Low
B1354 Passenger Airbag Circuit Short to Ground
B1355 Passenger Airbag Circuit Short to Battery
B1361 Seat Belt Pretensioner [Front- Driver] Resistance too High
B1362 Seat Belt Pretensioner [Front- Driver] Resistance too Low
B1363 Seat Belt Pretensioner [Front- Driver] Circuit Short to Ground
B1364 Seat Belt Pretensioner [Front- Driver] Circuit Short to Battery
B1367 Seat Belt Pretensioner [Front- Passenger] Resistance too High
B1368 Seat Belt Pretensioner [Front- Passenger] Resistance too Low
B1369 Seat Belt Pretensioner [Front- Passenger] Circuit Short to Ground
B1370 Seat Belt Pretensioner [Front- Passenger] Circuit Short to Battery
B1378 Side Airbag [Front- Driver] Resistance too High
B1379 Side Airbag [Front- Driver] Resistance too Low
B1380 Side Airbag [Front- Driver] Circuit Short to Ground
B1381 Side Airbag [Front- Driver] Circuit Short to Battery
B1382 Side Airbag [Front- Passenger] Resistance too High
B1383 Side Airbag [Front- Passenger] Resistance too Low
B1384 Side Airbag [Front- Passenger] Circuit Short to Ground
B1385 Side Airbag [Front- Passenger] Circuit Short to Battery
B1395 Squib Interconnection Fault
B1400 Side Impact Sensor [Front- Driver] Defect
B1403 Side Impact Sensor [Front- Passenger] Defect
B1409 Side Impact Sensor [Front- Driver] Communication Error
B1410 Side Impact Sensor [Front- Passenger] Communication Error
B1412 Side Impact Sensor [Rear- Driver] Communication Error
B1413 Side Impact Sensor [Rear- Passenger] Communication Error
B1418 Side Impact Sensor [Rear- Driver] Defect
B1419 Side Impact Sensor [Rear- Passenger] Defect
B1473 Curtain Airbag [Driver] Resistance too High
B1474 Curtain Airbag [Driver] Resistance too Low
B1475 Curtain Airbag [Driver] Circuit Short to Ground
B1476 Curtain Airbag [Driver] Circuit Short to Battery
B1477 Curtain Airbag [Passenger] Resistance too High
B1478 Curtain Airbag [Passenger] Resistance too Low
B1479 Curtain Airbag [Passenger] Circuit Short to Ground
B1480 Curtain Airbag [Passenger] Circuit Short to Battery
B1527 Passenger Airbag Deactivation Switch Open or Short to Battery
B1528 Passenger Airbag Deactivation Switch Short or Short to Ground

B1529Passenger Airbag Deactivation Switch Defect
B1530 Passenger Airbag Deactivation Switch Instability
B1620 Supplemental Restraint System Control Module Internal Fault (Replace SRSCM)
B1650 Crash Recorded - Frontal (Replace SRSCM)
B1651 Crash Recorded - Driver Side (Replace SRSCM)
B1652 Crash Recorded - Passenger Side (Replace SRSCM)
B1655 Crash Recorded - Passenger Side with PAB inhibited (Replace SRSCM)
B1657 Crash Recorded - Belt Pretensioner Only
B1658 Belt Pretensioner 6 times Deployment (Replace SRSCM)
B1701 Buckle Pretensioner [Front- Driver] Resistance Too High
B1702 Buckle Pretensioner [Front- Driver] Resistance Too Low
B1703 Buckle Pretensioner [Front- Driver] Resistance Circuit Short to Ground
B1704 Buckle Pretensioner [Front- Driver] Resistance Circuit Short to Battery
B1706 Buckle Pretensioner [Front- Passenger] Resistance Too High y
B1707 Buckle Pretensioner [Front- Passenger] Resistance Too Low
B1708 Buckle Pretensioner [Front- Passenger] Resistance Circuit Short to Ground y
B1709 Buckle Pretensioner [Front- Passenger] Resistance Circuit Short to Battery
B1722 Curtain Airbag [Rear- Driver] Resistance too High
B1723 Curtain Airbag [Rear- Driver] Resistance too Low
B1724 Curtain Airbag [Rear- Driver] Circuit short to Ground
B1725 Curtain Airbag [Rear- Driver] Circuit short to Battery
B1726 Curtain Airbag [Rear- Passenger] Resistance too High
B1727 Curtain Airbag [Rear- Passenger] Resistance too Low
B1728 Curtain Airbag [Rear- Passenger] Circuit short to Ground
B1729 Curtain Airbag [Rear- Passenger] Circuit short to Battery
B2500 SRS Warning Lamp Fault
B2505 Passenger Airbag Deactivation Lamp Fault

2007 > 2.7L V6 GASOLINE >
DESCRIPTION
The primary purpose of the SRSCM (Supplemental Restraints System Control Module) is to discriminate between an
event that warrants restraint system deployment and an event that does not. The SRSCM must decide whether to
deploy the restraint system or not. After determining that pretensioners and/or airbag deployment is required, the
SRSCM must supply sufficient power to the pretensioners and airbag igniters to initiate deployment. The SRSCM
determines that an impact may require deployment of the pretensioners and airbags from data obtained from impact
sensors and other components in conjunction with a safing function. The SRSCM will not be ready to detect a crash or
to activate the restraint system devices until the signals in the SRSCM circuitry stabilize. It is possible that the SRSCM
could activate the safety restraint devices in approximately 2 seconds but is guaranteed to fully function after prove-
out is completed. The SRSCM must perform a diagnostic routine and light a system readiness indicator at key - on. The
system must perform a continuous diagnostic routine and provide fault annunciation through a warning lamp indicator
in the event of fault detection. A serial diagnostic communication interface will be used to facilitate servicing of the
restraint control system.

2007 > 2.7L V6 GASOLINE >
removal
a.Removal of the airbag must be performed according to the precautions/ procedures described previously.
b. Before disconnecting the front impact sensor connector, disconnect the front airbag connector(s).
c. Do not turn the ignition switch ON and do not connect the battery cable while replacing the front impact
sensor.
1. Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2. Disconnect Front Impact Sensor conncetor.
3. Remove the FIS mounting bolt then remove the Front Impact Sensor.
INSTALLATION
a.Ensure that the harness is installed and routed properly to prevent damage to the wiring.
b. Do not turn the ignition switch ON and do not connect the battery cable while replacing the front impact
sensor.
1. Install the new Front Impact Sensor with bolt then connect the SRS harness connector to the Front Impact Sensor.
Tightening torque
: 1.0 ~ 1.4 kgf.m (9.5 ~ 13.6 Nm, 7.0 ~ 10.0 lb.ft)
2. Reconnect the negative battery cable.
3. After installing the Front Impact Sensor, confirm proper system operation: Turn the ignition switch ON the SRS
indicator light should be turned on for about six seconds and then go off.

2007 > 2.7L V6 GASOLINE >
REMOVAL
FRONT SIDE IMPACT SENSOR
a. Removal of the airbag must be performed according to the precautions/procedures described previously.
b. Before disconnecting the side impact sensor connector(s), disconnect the side airbag connector(s).
c. Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact
sensor.
1. Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2. Remove the door scuff trim. (Refer to BD group)
3. Remove the center pillar trim. (Refer to BD group)
4. Disconnect the Side Impact Sensor connector.
5. Remove the SIS mounting bolt then remove the Side Impact Sensor.
REAR SIDE IMPACT SENSOR
1.Disconnect the battery negative cable, and wait for at least three minutes before beginning work.
2. Remove the rear pillar trim. (Refer to BD group)
3. Disconnect the Side Impact Sensor connector.
4. Remove the SIS mounting bolt then remove the Side Impact Sensor.
INSTALLATION
FRONT SIDE IMPACT SENSOR

Airbag Module

2007 > 2.7L V6 GASOLINE >
AIRBAG DISPOSAL
SPECIAL TOOL REQUIRED
Before scrapping any airbags or side airbags (including those in a whole vehicle to be scrapped), the airbags or side
airbags must be deployed. If the vehicle is still within the warranty period, before deploying the airbags or side airbags,
the Technical Manager must give approval and/or special instruction. Only after the airbags or side airbags have been
deployed (as the result of vehicle collision, for example), can they be scrapped.
If the airbags or side airbags appear intact (not deployed), treat them with extreme caution. Follow this procedure.
DEPLOYING AIRBAGS IN THE VEHICLE
If an SRS equipped vehicle is to be entirely scrapped, its airbags or side airbags should be deployed while still in the
vehicle. The airbags or side airbags should not be considered as salvageable parts and should never be installed in
another vehicle. 1. Turn the ignition switch OFF, and disconnect the battery negative cable and wait at least three minutes.
2. Confirm that each airbag or side airbag is securely mounted.
3. Confirm that the special tool is functioning properly by following the check procedure.
DRIVER'S AIRBAG :
1.Remove the driver's airbag and install the SST(0957A - 38500).
2. Install the driver's airbag on the steering wheel.
FRONT PASSENGER'S AIRBAG :
1.Remove the glove box, then disconnect the 2P connector between the front passenger's airbag and SRS main
harness.
2. Install the SST(0957A - 3F100).
SIDE AIRBAG :
1.Disconnect the 2P connector between the side airbag and side wire harness.
2. Install the SST (0957A- 3F100).
CURTAIN AIRBAG :
1.Disconnect the 2P connector between the curtain airbag and wire harness.
2. Install the SST(0957A - 38500).
SEAT BELT PRETENSIONER :
1.Disconnect the 2P connector from the seat belt pretensioner.
2. Install the SST(0957A - 38500).
3. Place the deployment tool at least thirty feet (10 meters) away from the airbag.
4. Connect a 12 volt battery to the tool.
5. Push the tool's deployment switch. The airbag should deploy (deployment is both highly audible and visible: a loud
noise and rapid inflation of the bag, followed by slow deflection)
6. Dispose of the complete airbag. No part of it can be reused. Place it in a sturdy plastic bag and seal it securely.

DEPLOYING THE AIRBAG OUT OF THE VEHICLE
If an intact airbag has been removed from a scrapped vehicle, or has been found defective or damage during transit,
storage or service, it should be deployed as follows :1. Position the airbag face up, outdoors on flat ground at least thirty feet (10meters) from any obstacles or people.
DISPOSAL OF DAMAGED AIRBAG
1.If installed in a vehicle, follow the removal procedure of driver's airbag front passenger's and side airbag.
2. In all cases, make a short circuit by twisting together the two airbag inflator wires.
3. Package the airbag in exactly the same packing that the new replacement part come in.

Drive Airbag (DAB) Module and
Clock Spring