parking brake KIA CARNIVAL 2007 User Guide

TIGHTENING TORQUE
ItemsNmkgf.m lb - ft
Master cylinder to booster mounting nut 8 ~ 120.8 ~ 1.2 5.8 ~ 8.7
Brake booster mounting nut 13 ~ 161.3 ~ 1.6 9.4 ~ 11.6
Bleeder screw 7 ~ 130.7 ~ 1.3 5.06 ~ 9.4
Brake tube nut, brake hose 13 ~ 171.3 ~ 1.7 9.4 ~ 12.3
Caliper guide rod bolt (Front) 22 ~ 322.2 ~ 3.215.9 ~ 23.1
Caliper guide rod bolt (Rear) 22 ~ 322.2 ~ 3.215.9 ~ 23.1
Caliper assembly to knuckle (Front) 85 ~ 1008.5 ~ 1061.5 ~ 72.3
Caliper assembly to knuckle (Rear) 50 ~ 605.0 ~ 6.036.2 ~ 43.4
Brake hose to front caliper 25 ~ 302.5 ~ 3.018.1 ~ 21.7
Brake pedal assembly bracket mounting nut 10 ~ 151.0 ~ 1.5 7.2 ~ 10.8
Brake pedal mounting nut 13 ~ 161.3 ~ 1.6 9.4 ~ 11.6
Stop lamp switch mounting nut 8 ~ 100.8 ~ 1.0 5.8 ~ 7.23
Active wheel speed sensor mounting bolt on
the brake plate 7 ~ 10
0.7 ~ 1.0 5.1 ~ 7.2
HECU mounting bracket bolt 17 ~ 261.7 ~ 2.612.3 ~ 18.8
HECU mounting nut 6 ~ 100.6 ~ 1.0 4.3 ~ 7.2
Yaw rate & lateral acceleration sensor bolt 5 ~ 80.5 ~ 0.8 3.62 ~ 5.8
SPECIFICATION (ABS)
Part ItemStandard valueRemark
HECU(Hydraulic and
Electronic Control
Unit) System
4 channel 4 sensor
(Solenoid)
·ABS system:ABS &
EBD control
Type
Motor, valve relay
intergrated type
Operating voltage 8 V ~ 16 V(DC)
Operating temperature - 40 ~ 120 °C
( - 40 ~ 248 °F)
Warning lamp Operating voltage
12 V·ABS W/L:ABS failure
·Brake W/L:Parking,
brake oil, EBD failure
Current consumption 80 mA
Acitve wheel speed
sensor Supply voltage
DC 4.5 ~ 2.0 V
Operating temperature - 40 ~ 150 °C
Output current low 5.9 ~ 8.4 mATyp.7 mA
Output current High 11.8 ~ 16.8 mATyp.14 mA
Frequency range 1 ~ 2500 HZ
Air gap Front
0.15 ~ 1.5 mm Typ.0.7 mm
Rear 0.2 ~ 1.2 mm Typ.0.7 mm
Tone wheel 48 teeth
Output duty 30~70 %
SPECIFICATION(ESP)

PartItemStandard ValueRemark
HECU(Hydraulic and
Electronic Control
Unit) System
4 channel 4
sensor(Solenoid)
·Total control(ABS,
EBD, TCS, ESP)
Type
Motor, valve relay
intergrated type
Operating voltage 8 V ~ 16 V(DC)
Operating temperature - 40 ~ 120 °C(- 40 ~
248 °F)
Warning lamp Operating voltage
12 V
·ESP Operating Lamp
·ESP Warning Lamp
Current consumption 80 mA
Active wheel speed
sensor Supply voltage
DC 4.5 ~ 20V
Operating temperature - 40 ~ 150 °C
Output current low 5.9 ~ 8.4 mA
Output current high 11.8 ~ 16.8 mA
Tone wheel 48 teeth
Frequency range 1 ~ 2500 HZ
Airgap Front
0.15 ~ 1.5 mm Typ. 0.7 mm
Rear 0.2 ~ 1.2 mm Typ. 0.7 mm
Steering Wheel Angle
Sensor Operating Voltage
8V ~ 16 V
Current Consumption Max 150 mA
Operating Angular velocity Max ± 780 °/sec
Yaw - rate & Lateral G
sensor Operating Voltage
8 V ~ 16 V
Current Consumption Max. 120 mA
Output Voltage high 4.35 V~ 4.65 VTyp. 4.5 V
Output Voltage low 0.35 ~ 0.65 VTyp. 0.5 V
Yaw Sensor Operating Range ±100 ° /s
G Sensor Operating Range ±1.8 G
Reference voltage output 2.464 ~ 2.536 VTyp. 2.5 V
LUBRICANT
Item Recommended lubricantQuantity
Brake fluid DOT 3 or DOT 4As required
Brake pedal bushing and brake pedal bolt Chassis greaseAs required
Parking brake shoe and backing plate contact surfaces Bearing greaseAs required
Caliper guide rod and boot RX - 2 grease0.8 ~ 1.3 g
Rear caliper guide rod and boot Rubber grease0.8 ~ 1.3g

Parking Brake System
Parking Brake Assembly

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Remove the lower panel (A), after loosening the parking lever. (Refer to BD group 'Crash pad')
2.Remove the parking release nose (B).
3. Remove the parking brake switch (A).
[LHD]
[RHD]
4.Remove the parking brake cable (A).

5.Remove the mounting nuts (A) and bolt (B) of the parking brake bracket.
[LHD]
[RHD]
6.Remove the release cable assembly (C).
7. Remove the damper assembly (A).
[LHD]

[RHD]
8.Remove the parking brake lamp switch (A).
[LHD]
9.Raise the rear of the vehicle and make sure it is securely supported.
10. Remove the mounting bolt (A) of the parking brake wire bracket from the body.

11.Remove the four mounting bolts (A) of the parking brake wire bracket from the rear cross member.
12.Remove the rear wheels and tires from the rear hubs.
13. Remove the hub cap (A) and the disc (B).
14.Remove the hub nut (A) and washer (B) and remove the rear hub (C).
15.Remove the shoe hold down pin and spring (A) by pressing and rotating the spring.

16.Remove the adjuster assembly (B) and the lower return spring (C).
17. Remove the strut (B) and the upper return spring (A).
18.Remove the retaining ring (B) of the parking brake wire (A) from back of the backing plate.
19.Disconnect the parking brake wire from the brake shoe.
INSTALLATION
1.Install the backing plate (A).

2.Connect the parking brake wire (B) to the brake shoe (A).
3.Install the shoe hold down pin and spring (A) to hold the brake shoe (B).
4.Install the adjuster assembly (B) and the lower return spring (C).
5. Install the upper return spring (A) and strut (B).
6.Grease where is necessary.
7. Install the rear hubs.
8. Install the hub nut (A). After installation, lock the nut to the spindle as shown in the illustration.

9.Install the hub cap (A) and the disc (B).
10. Install the rear wheels and tires from the rear hubs.
11. Tighten the parking brake adjusting nut.
12. Install the parking brake wire and the pedal assembly.
ADJUSTMENT
ADJUSTMENT OF REAR BRAKE SHOE CLEARANCE
1. Raise the vehicle, and make sure it is securely supported.
2. Remove the rear wheel and tire from the rear hub.
3. After removing the plug from the disc, rotate the toothed wheel by a screw driver until the disc is not moving, and
then return it by 5 notches.
ADJUSTMENT PRECEDURE OF DIH FOOT PARKING BRAKE
1.Adjust the adjusting nut (A) so that parking pedal stoke is to be 88 ~ 98 mm(3.46 ~ 3.86 in) when operating effort
is 200 N(20 kgf, 44 lb) after full stroke operation of parking pedal over 3 times for setting parking wire.