width KIA CARNIVAL 2007 Workshop Manual

Valve stem to valve
guide clearanceIntake
0.020 ~ 0.050mm(0.0008 ~ 0.0020in.) 0.10mm(0.0039in.)
or less
Exhaust 0.035 ~ 0.065mm(0.0014 ~ 0.0026in.) 0.13mm(0.0051in.)
or less
Valve guide
Inner diameter Intake 6.000 ~ 6.015mm(2.2362 ~ 2.2368in.)
Exhaust 6.000 ~ 6.015mm(2.2362 ~ 2.2368in.)
Length Intake 45.8 ~ 46.2mm(1.8031 ~ 1.8189in.)
Exhaust 46.8 ~ 47.2mm(1.8425 ~ 1.8583in.)
Valve spring
Free length 46.8mm(1.8425in.)
Load Height: 35mm 180.5 ~ 199.5N(18.4 ~ 20.3Kgf, 40.6 ~ 44.8lb)
Height: 26.5mm 342 ~ 378N(34.9 ~ 38.6Kgf, 76.9 ~ 85.1lb)
Out of squareness 1.5° or less
MLA(Mechanical Lash Adjuster)
MLA outer diameter Intake 29.964 ~ 29.980mm(1.1797 ~ 1.1803in.)
Exhaust 29.964 ~ 29.980mm(1.1797 ~ 1.1803in.)
Cylinder head
tappet bore inner
diameter Intake
30.000 ~ 30.025mm(1.1811 ~ 1.1821in.)
Exhaust 30.000 ~ 30.025mm(1.1811 ~ 1.1821in.)
MLA to tappet bore
clearance Intake
0.020 ~ 0.061mm(0.0008 ~ 0.0024in.) 0.07mm(0.0027in.)
or less
Exhaust 0.020 ~ 0.061mm(0.0008 ~ 0.0024in.) 0.07mm(0.0027in.)
or less
Valve clearance
Intake 0.17 ~ 0.23mm (0.0067 ~ 0.0090in.) 0.10 ~ 0.30mm
(0.0039 ~
0.0118in.)
Exhaust 0.27 ~ 0.33mm (0.0106 ~ 0.0129in.) 0.20 ~ 0.40mm
(0.0078 ~
0.0157in.)
Cylinder block
Cylinder bore 96.00 ~ 96.03mm (3.7795 ~ 3.7807in.)
Flatness of gasket surface Less than 0.05mm (0.0019in.)
[Less than 0.02mm (0.0008in.) / 150x150]
Piston
Piston outer diameter 95.96 ~ 95.99mm(3.7779 ~ 3.7791in.)
Piston to cylinder clearance 0.03 ~ 0.05mm(0.0012 ~ 0.0020in.)
Ring groove width No. 1 ring groove 1.22 ~ 1.24mm (0.0480 ~ 0.0488in.)
No. 2 ring groove 1.22 ~ 1.24mm (0.0480 ~ 0.0488in.)
Oil ring groove 2.01 ~ 2.03mm (0.0791 ~ 0.0799in.)
Piston O.S. 0.25mm(0.0098in.)
Piston ring
Side clearance No. 1 ring 0.04 ~ 0.08mm(0.0016 ~ 0.0031in.) 0.1mm(0.0039in.)

If the margin thickness is less than the specification, replace the valve.
Specification
Intake : 1.0mm(0.0394in.)
Exhaust : 1.3mm(0.0512.)
(4)Check the valve length.
Length
Intake : 110.1mm(4.3346in)
Exhaust : 111.1mm(4.3740in)
(5) Check the surface of the valve stem tip for wear.
If the valve stem tip is worn, replace the valve.
3. Inspect valve seats
(1) Check the valve seat for evidence of overheating or improper contact with the valve face.
If the valve seat is worn, replace cylinder head.
(2) Before reconditioning the seat, check the valve guide for wear. If the valve guide is worn, replace the valve
guide first.
(3) Recondition the valve seat with a valve seat grinder or cutter. The valve seat contact width should be within
specifications and centered on the valve face.
4. Inspect valve springs.
(1) Using a steel square, measure the out - of- square of the valve spring.
(2) Using vernier calipers, measure the free length of the valve spring.
Valve spring
[Standard]
Free height : 46.8mm (1.8425in.)
Out- of- square : 1.5° or less

Tightening torque
39.2 ~ 49.0Nm (4.0 ~ 5.0kgf.m, 28.9 ~ 36.2lb- ft)
2.Install oil pump case.
(1) Using a gasket scraper, remove all the old packing material from the gasket surfaces.
(2) Before assembling the oil pan, the liquid sealant TB1217H should be applied on the oil pan.
The part must be assembled within 5 minutes after the sealant was applied.
Bead width : 2.5mm(0.0984in.)
a.Make clean the sealing face before assembling two parts.
b. Remove harmful foreign materials on the sealing face before applying sealant.
c. When applying sealant gasket, sealant must not be protrude into the inside of oil pan.
d. To prevent leakage of oil, apply sealant gasket to the inner threads of the bolt holes.
e. After assembly, wait at least 30 minutes before filling the engine with oil.
(3) Install the oil pump case(A).
Tightening torque
18.6 ~ 23.5(1.9 ~ 2.4kgf.m, 13.7 ~ 17.4lb- ft)